Merge branch 'master' of http://www.denx.de/git/u-boot
diff --git a/CHANGELOG b/CHANGELOG
index e39b1e7..82be4e3 100644
--- a/CHANGELOG
+++ b/CHANGELOG
@@ -2,6 +2,55 @@
Changes since U-Boot 1.1.4:
======================================================================
+* Add support for WTK FO300 board (TQM5200 based).
+
+* Fix TQM834x hang.
+
+* Update for SC520 board.
+ Patch by David Updegraff, 02 Dec 2005
+
+* Fixed common.h spelling error.
+ Patch by Cory Tusar, 30 Nov 2005
+
+* Fix typo.
+ Patch by Andreas Engel, 28 Nov 2005
+
+* Fix fatload command on FAT32 formatted partitions.
+ Patch by Joachim Jaeger, 18 Nov 2005
+
+* Fix drivers/dm9000.c when configured in 32 bit mode.
+ Patch by Eric Benard, 17 Nov 2005
+
+* Cleanup debug code for yucca board.
+
+* MCC200: restrict addressable flash space to 32 MB
+
+* Add debug console on COM12 for MCC200 board
+
+* Fix control-c handing in CONFIG_CMDLINE_EDITING
+ Properly pass break code back from readline.
+ Patch by Roger Blofeld, 31 Jul 2006
+
+* Add commandline history support to all AMCC eval boards
+ Patch by Stefan Roese, 07 Aug 2006
+
+* Add Macronix MXLV320T flash support for AMCC Bamboo
+ Patch by Stefan Roese, 07 Aug 2006
+
+* Change "mii info" to not print an error upon missing PHY at address
+ Patch by Stefan Roese, 07 Aug 2006
+
+* Fix PCI-Express on PPC440SPe rev. A.
+
+* Fix preboot message on TQM85xx after switching to hush parser.
+
+* Adapt TQM85xx ramdisk address to Linux kernel memory map
+
+* Add initial support for PCI-Express on PPC440SPe (Yucca board).
+
+* Fix compiler warning for TRAB board.
+ Patch by Martin Krause, 07 Aug 2006
+
* Prevent USB commands from working when USB is stopped.
* Add rudimentary handling of alternate settings of USB interfaces.
diff --git a/MAKEALL b/MAKEALL
index 467a9be..720ab03 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -25,11 +25,11 @@
#########################################################################
LIST_5xxx=" \
- BC3450 cpci5200 EVAL5200 icecube_5100 \
- icecube_5200 lite5200b mcc200 o2dnt \
- pf5200 PM520 TB5200 Total5100 \
- Total5200 Total5200_Rev2 TQM5200 TQM5200_B \
- TQM5200S \
+ BC3450 cpci5200 EVAL5200 fo300 \
+ icecube_5100 icecube_5200 lite5200b mcc200 \
+ o2dnt pf5200 PM520 TB5200 \
+ Total5100 Total5200 Total5200_Rev2 TQM5200 \
+ TQM5200_B TQM5200S \
"
#########################################################################
diff --git a/Makefile b/Makefile
index 2eec40d..8cc2664 100644
--- a/Makefile
+++ b/Makefile
@@ -328,6 +328,7 @@
mcc200_config \
mcc200_SDRAM \
mcc200_highboot \
+mcc200_COM12 \
mcc200_highboot_SDRAM: unconfig
@ >include/config.h
@[ -n "$(findstring highboot,$@)" ] || \
@@ -344,6 +345,10 @@
{ echo "#define CONFIG_MCC200_SDRAM" >>include/config.h ; \
echo "... with SDRAM" ; \
}
+ @[ -z "$(findstring COM12,$@)" ] || \
+ { echo "#define CONFIG_CONSOLE_COM12" >>include/config.h ; \
+ echo "... with console on COM12" ; \
+ }
@./mkconfig -a mcc200 ppc mpc5xxx mcc200
o2dnt_config:
@@ -415,25 +420,30 @@
}
@./mkconfig -a Total5200 ppc mpc5xxx total5200
-TQM5200_config \
-TQM5200_B_config \
-TQM5200_B_HIGHBOOT_config \
+cam5200_config \
+fo300_config \
+MiniFAP_config \
TQM5200S_config \
TQM5200S_HIGHBOOT_config \
-TQM5200_STK100_config \
-cam5200_config \
-MiniFAP_config: unconfig
+TQM5200_B_config \
+TQM5200_B_HIGHBOOT_config \
+TQM5200_config \
+TQM5200_STK100_config: unconfig
@ >include/config.h
- @[ -z "$(findstring MiniFAP,$@)" ] || \
- { echo "#define CONFIG_MINIFAP" >>include/config.h ; \
- echo "... TQM5200_AC on MiniFAP" ; \
- }
@[ -z "$(findstring cam5200,$@)" ] || \
{ echo "#define CONFIG_CAM5200" >>include/config.h ; \
echo "#define CONFIG_TQM5200S" >>include/config.h ; \
echo "#define CONFIG_TQM5200_B" >>include/config.h ; \
echo "... TQM5200S on Cam5200" ; \
}
+ @[ -z "$(findstring fo300,$@)" ] || \
+ { echo "#define CONFIG_FO300" >>include/config.h ; \
+ echo "... TQM5200 on FO300" ; \
+ }
+ @[ -z "$(findstring MiniFAP,$@)" ] || \
+ { echo "#define CONFIG_MINIFAP" >>include/config.h ; \
+ echo "... TQM5200_AC on MiniFAP" ; \
+ }
@[ -z "$(findstring STK100,$@)" ] || \
{ echo "#define CONFIG_STK52XX_REV100" >>include/config.h ; \
echo "... on a STK52XX.100 base board" ; \
diff --git a/board/amcc/common/flash.c b/board/amcc/common/flash.c
index 3a50b09..a0acbba 100644
--- a/board/amcc/common/flash.c
+++ b/board/amcc/common/flash.c
@@ -76,6 +76,9 @@
case FLASH_MAN_SST:
printf("SST ");
break;
+ case FLASH_MAN_MX:
+ printf ("MACRONIX ");
+ break;
default:
printf("Unknown Vendor ");
break;
@@ -124,6 +127,9 @@
case FLASH_STMW320DT:
printf ("M29W320DT (32 M, top sector)\n");
break;
+ case FLASH_MXLV320T:
+ printf ("MXLV320T (32 Mbit, top sector)\n");
+ break;
default:
printf("Unknown Chip Type\n");
break;
@@ -375,6 +381,7 @@
{
if (((info->flash_id & FLASH_TYPEMASK) == FLASH_AM320B) ||
((info->flash_id & FLASH_TYPEMASK) == FLASH_AM320T) ||
+ ((info->flash_id & FLASH_TYPEMASK) == FLASH_MXLV320T) ||
((info->flash_id & FLASH_TYPEMASK) == FLASH_STMW320DT)) {
return flash_erase_2(info, s_first, s_last);
} else {
@@ -555,6 +562,7 @@
{
if (((info->flash_id & FLASH_TYPEMASK) == FLASH_AM320B) ||
((info->flash_id & FLASH_TYPEMASK) == FLASH_AM320T) ||
+ ((info->flash_id & FLASH_TYPEMASK) == FLASH_MXLV320T) ||
((info->flash_id & FLASH_TYPEMASK) == FLASH_STMW320DT)) {
return write_word_2(info, dest, data);
} else {
@@ -648,6 +656,9 @@
case (CFG_FLASH_WORD_SIZE) STM_MANUFACT:
info->flash_id = FLASH_MAN_STM;
break;
+ case (CFG_FLASH_WORD_SIZE) MX_MANUFACT:
+ info->flash_id = FLASH_MAN_MX;
+ break;
default:
info->flash_id = FLASH_UNKNOWN;
info->sector_count = 0;
@@ -676,6 +687,12 @@
info->sector_count = 67;
info->size = 0x00400000; break; /* => 4 MB */
+ case (CFG_FLASH_WORD_SIZE)MX_ID_LV320T:
+ info->flash_id += FLASH_MXLV320T;
+ info->sector_count = 71;
+ info->size = 0x00400000;
+ break; /* => 4 MB */
+
default:
info->flash_id = FLASH_UNKNOWN;
return (0); /* => no or unknown flash */
@@ -711,6 +728,19 @@
--i;
info->start[i] = base;
}
+ } else if ((info->flash_id & FLASH_TYPEMASK) == FLASH_MXLV320T) {
+ i = info->sector_count - 1;
+ info->start[i--] = base + info->size - 0x00002000;
+ info->start[i--] = base + info->size - 0x00004000;
+ info->start[i--] = base + info->size - 0x00006000;
+ info->start[i--] = base + info->size - 0x00008000;
+ info->start[i--] = base + info->size - 0x0000a000;
+ info->start[i--] = base + info->size - 0x0000c000;
+ info->start[i--] = base + info->size - 0x0000e000;
+ info->start[i--] = base + info->size - 0x00010000;
+
+ for (; i >= 0; i--)
+ info->start[i] = base + i * 0x00010000;
} else {
if (info->flash_id & FLASH_BTYPE) {
/* set sector offsets for bottom boot block type */
diff --git a/board/amcc/yucca/init.S b/board/amcc/yucca/init.S
index cb28936..c9eca68 100644
--- a/board/amcc/yucca/init.S
+++ b/board/amcc/yucca/init.S
@@ -82,9 +82,12 @@
*************************************************************************/
.section .bootpg,"ax"
- .globl tlbtab
-tlbtab:
+/**************************************************************************
+ * TLB table for revA
+ *************************************************************************/
+ .globl tlbtabA
+tlbtabA:
tlbtab_start
tlbentry(0xfff00000, SZ_16M, 0xfff00000, 4, AC_R|AC_W|AC_X|SA_G)
@@ -94,11 +97,56 @@
tlbentry(CFG_SDRAM_BASE + 0x30000000, SZ_256M, 0x30000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I)
tlbentry(CFG_ISRAM_BASE, SZ_256K, 0x00000000, 4, AC_R|AC_W|AC_X|SA_I)
- tlbentry(CFG_FPGA_BASE,SZ_1K, 0xE2000000, 4,AC_R|AC_W|SA_I)
+ tlbentry(CFG_FPGA_BASE, SZ_1K, 0xE2000000, 4,AC_R|AC_W|SA_I)
- tlbentry(CFG_OPER_FLASH,SZ_16M,0xE7000000, 4,AC_R|AC_W|AC_X|SA_G|SA_I)
+ tlbentry(CFG_OPER_FLASH, SZ_16M, 0xE7000000, 4,AC_R|AC_W|AC_X|SA_G|SA_I)
tlbentry(CFG_PERIPHERAL_BASE, SZ_4K, 0xF0000000, 4, AC_R|AC_W|SA_G|SA_I)
tlbentry(CFG_PCI_BASE, SZ_256M, 0x00000000, 0xC, AC_R|AC_W|SA_G|SA_I)
tlbentry(CFG_PCI_MEMBASE, SZ_256M, 0x10000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE_MEMBASE, SZ_256M, 0xB0000000, 0xD, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE_BASE, SZ_16K, 0x20000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+
+ tlbentry(CFG_PCIE0_CFGBASE, SZ_1K, 0x40000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE1_CFGBASE, SZ_1K, 0x80000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE2_CFGBASE, SZ_1K, 0xC0000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE0_XCFGBASE, SZ_1K, 0x50000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE1_XCFGBASE, SZ_1K, 0x90000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE2_XCFGBASE, SZ_1K, 0xD0000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+ tlbtab_end
+
+/**************************************************************************
+ * TLB table for revB
+ *
+ * Notice: revB of the 440SPe chip is very strict about PLB real addresses
+ * and ranges to be mapped for config space: it seems to only work with
+ * d_nnnn_nnnn range (hangs the core upon config transaction attempts when
+ * set otherwise) while revA uses c_nnnn_nnnn.
+ *************************************************************************/
+ .globl tlbtabB
+tlbtabB:
+ tlbtab_start
+ tlbentry(0xfff00000, SZ_16M, 0xfff00000, 4, AC_R|AC_W|AC_X|SA_G)
+
+ tlbentry(CFG_SDRAM_BASE, SZ_256M, 0x00000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I)
+ tlbentry(CFG_SDRAM_BASE + 0x10000000, SZ_256M, 0x10000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I)
+ tlbentry(CFG_SDRAM_BASE + 0x20000000, SZ_256M, 0x20000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I)
+ tlbentry(CFG_SDRAM_BASE + 0x30000000, SZ_256M, 0x30000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I)
+
+ tlbentry(CFG_ISRAM_BASE, SZ_256K, 0x00000000, 4, AC_R|AC_W|AC_X|SA_I)
+ tlbentry(CFG_FPGA_BASE, SZ_1K, 0xE2000000, 4,AC_R|AC_W|SA_I)
+
+ tlbentry(CFG_OPER_FLASH, SZ_16M, 0xE7000000, 4,AC_R|AC_W|AC_X|SA_G|SA_I)
+ tlbentry(CFG_PERIPHERAL_BASE, SZ_4K, 0xF0000000, 4, AC_R|AC_W|SA_G|SA_I)
+
+ tlbentry(CFG_PCI_BASE, SZ_256M, 0x00000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCI_MEMBASE, SZ_256M, 0x10000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE_MEMBASE, SZ_256M, 0xB0000000, 0xD, AC_R|AC_W|SA_G|SA_I)
+
+ tlbentry(CFG_PCIE0_CFGBASE, SZ_1K, 0x00100000, 0xD, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE1_CFGBASE, SZ_1K, 0x20100000, 0xD, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE2_CFGBASE, SZ_1K, 0x40100000, 0xD, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE0_XCFGBASE, SZ_1K, 0x10000000, 0xD, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE1_XCFGBASE, SZ_1K, 0x30000000, 0xD, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE2_XCFGBASE, SZ_1K, 0x50000000, 0xD, AC_R|AC_W|SA_G|SA_I)
tlbtab_end
diff --git a/board/amcc/yucca/yucca.c b/board/amcc/yucca/yucca.c
index ce1312c..af12839 100644
--- a/board/amcc/yucca/yucca.c
+++ b/board/amcc/yucca/yucca.c
@@ -21,12 +21,16 @@
* MA 02111-1307 USA
*
* Port to AMCC-440SPE Evaluation Board SOP - April 2005
+ *
+ * PCIe supporting routines derived from Linux 440SPe PCIe driver.
*/
#include <common.h>
#include <ppc4xx.h>
#include <asm/processor.h>
#include <i2c.h>
+#include <asm-ppc/io.h>
+
#include "yucca.h"
void fpga_init (void);
@@ -39,6 +43,9 @@
unsigned long ppcMfcpr(unsigned long cpr_reg);
unsigned long ppcMfsdr(unsigned long sdr_reg);
+int ppc440spe_init_pcie_rootport(int port);
+void ppc440spe_setup_pcie(struct pci_controller *hose, int port);
+
#define DEBUG_ENV
#ifdef DEBUG_ENV
#define DEBUGF(fmt,args...) printf(fmt ,##args)
@@ -908,6 +915,7 @@
}
#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */
+#if defined(CONFIG_PCI)
/*************************************************************************
* is_pci_host
*
@@ -923,12 +931,132 @@
*
*
************************************************************************/
-#if defined(CONFIG_PCI)
int is_pci_host(struct pci_controller *hose)
{
/* The yucca board is always configured as host. */
return 1;
}
+
+
+int yucca_pcie_card_present(int port)
+{
+ u16 reg;
+
+ reg = in_be16((u16 *)FPGA_REG1C);
+ switch(port) {
+ case 0:
+ return !(reg & FPGA_REG1C_PE0_PRSNT);
+ case 1:
+ return !(reg & FPGA_REG1C_PE1_PRSNT);
+ case 2:
+ return !(reg & FPGA_REG1C_PE2_PRSNT);
+ default:
+ return 0;
+ }
+}
+
+/*
+ * For the given slot, set rootpoint mode, send power to the slot,
+ * turn on the green LED and turn off the yellow LED, enable the clock
+ * and turn off reset.
+ */
+void yucca_setup_pcie_fpga_rootpoint(int port)
+{
+ u16 power, clock, green_led, yellow_led, reset_off, rootpoint, endpoint;
+
+ switch(port) {
+ case 0:
+ rootpoint = FPGA_REG1C_PE0_ROOTPOINT;
+ endpoint = 0;
+ power = FPGA_REG1A_PE0_PWRON;
+ green_led = FPGA_REG1A_PE0_GLED;
+ clock = FPGA_REG1A_PE0_REFCLK_ENABLE;
+ yellow_led = FPGA_REG1A_PE0_YLED;
+ reset_off = FPGA_REG1C_PE0_PERST;
+ break;
+ case 1:
+ rootpoint = 0;
+ endpoint = FPGA_REG1C_PE1_ENDPOINT;
+ power = FPGA_REG1A_PE1_PWRON;
+ green_led = FPGA_REG1A_PE1_GLED;
+ clock = FPGA_REG1A_PE1_REFCLK_ENABLE;
+ yellow_led = FPGA_REG1A_PE1_YLED;
+ reset_off = FPGA_REG1C_PE1_PERST;
+ break;
+ case 2:
+ rootpoint = 0;
+ endpoint = FPGA_REG1C_PE2_ENDPOINT;
+ power = FPGA_REG1A_PE2_PWRON;
+ green_led = FPGA_REG1A_PE2_GLED;
+ clock = FPGA_REG1A_PE2_REFCLK_ENABLE;
+ yellow_led = FPGA_REG1A_PE2_YLED;
+ reset_off = FPGA_REG1C_PE2_PERST;
+ break;
+
+ default:
+ return;
+ }
+
+ out_be16((u16 *)FPGA_REG1A,
+ ~(power | clock | green_led) &
+ (yellow_led | in_be16((u16 *)FPGA_REG1A)));
+
+ out_be16((u16 *)FPGA_REG1C,
+ ~(endpoint | reset_off) &
+ (rootpoint | in_be16((u16 *)FPGA_REG1C)));
+ /*
+ * Leave device in reset for a while after powering on the
+ * slot to give it a chance to initialize.
+ */
+ udelay(250 * 1000);
+
+ out_be16((u16 *)FPGA_REG1C, reset_off | in_be16((u16 *)FPGA_REG1C));
+}
+
+
+static struct pci_controller pcie_hose[3] = {{0},{0},{0}};
+
+void pcie_setup_hoses(void)
+{
+ struct pci_controller *hose;
+ int i, bus;
+
+ /*
+ * assume we're called after the PCIX hose is initialized, which takes
+ * bus ID 0 and therefore start numbering PCIe's from 1.
+ */
+ bus = 1;
+ for (i = 0; i <= 2; i++) {
+ /* Check for yucca card presence */
+ if (!yucca_pcie_card_present(i))
+ continue;
+
+ yucca_setup_pcie_fpga_rootpoint(i);
+
+ if (ppc440spe_init_pcie_rootport(i)) {
+ printf("PCIE%d: initialization failed\n", i);
+ continue;
+ }
+
+ hose = &pcie_hose[i];
+ hose->first_busno = bus;
+ hose->last_busno = bus;
+ bus++;
+
+ /* setup mem resource */
+ pci_set_region(hose->regions + 0,
+ CFG_PCIE_MEMBASE + i * CFG_PCIE_MEMSIZE,
+ CFG_PCIE_MEMBASE + i * CFG_PCIE_MEMSIZE,
+ CFG_PCIE_MEMSIZE,
+ PCI_REGION_MEM
+ );
+ hose->region_count = 1;
+ pci_register_hose(hose);
+
+ ppc440spe_setup_pcie(hose, i);
+ hose->last_busno = pci_hose_scan(hose);
+ }
+}
#endif /* defined(CONFIG_PCI) */
int misc_init_f (void)
diff --git a/board/mcc200/mcc200.c b/board/mcc200/mcc200.c
index 167dc0f..775030c 100644
--- a/board/mcc200/mcc200.c
+++ b/board/mcc200/mcc200.c
@@ -203,6 +203,8 @@
int misc_init_r (void)
{
+ ulong flash_sup_end, snum;
+
/*
* Adjust flash start and offset to detected values
*/
@@ -257,6 +259,12 @@
(flash_info[0].start[0] - 1) + flash_info[0].size,
&flash_info[0]);
*(volatile int*)MPC5XXX_CS0_CFG &= ~(1 << 6);
+ printf ("Warning: Only 32 of 64 MB of Flash are accessible from U-Boot\n");
+ flash_info[0].size = 32 << 20;
+ for (snum = 0, flash_sup_end = gd->bd->bi_flashstart + (32<<20);
+ flash_info[0].start[snum] < flash_sup_end;
+ snum++);
+ flash_info[0].sector_count = snum;
}
return (0);
diff --git a/board/tqm5200/cmd_stk52xx.c b/board/tqm5200/cmd_stk52xx.c
index c37d4c6..7af69f2 100755
--- a/board/tqm5200/cmd_stk52xx.c
+++ b/board/tqm5200/cmd_stk52xx.c
@@ -30,8 +30,8 @@
#include <command.h>
#if (CONFIG_COMMANDS & CFG_CMD_BSP)
-#if defined (CONFIG_STK52XX)
+#if defined(CONFIG_STK52XX) || defined(CONFIG_FO300)
#define DEFAULT_VOL 45
#define DEFAULT_FREQ 500
#define DEFAULT_DURATION 200
@@ -537,7 +537,9 @@
return rcode;
}
+#endif
+#if defined(CONFIG_STK52XX)
void led_init(void)
{
struct mpc5xxx_gpio *gpio = (struct mpc5xxx_gpio *)MPC5XXX_GPIO;
@@ -736,7 +738,9 @@
return 0;
}
+#endif
+#if defined(CONFIG_STK52XX) || defined(CONFIG_FO300)
/*
* return 1 on CAN initialization failure
* return 0 if no failure
@@ -1106,6 +1110,7 @@
return error_status;
}
+#ifndef CONFIG_FO300
static void sm501_backlight (unsigned int state)
{
if (state == BL_ON) {
@@ -1115,6 +1120,7 @@
*(vu_long *)(SM501_MMIO_BASE+SM501_PANEL_DISPLAY_CONTROL) &=
~((1 << 26) | (1 << 27));
}
+#endif
int cmd_fkt(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
{
@@ -1124,7 +1130,9 @@
printf ("Revision 100 of STK52XX not supported!\n");
return 1;
#endif
+#if defined(CONFIG_STK52XX)
led_init();
+#endif
can_init();
switch (argc) {
@@ -1152,6 +1160,7 @@
else
printf ("Error\n");
return rcode;
+#ifndef CONFIG_FO300
} else if (strncmp (argv[1], "backlight", 4) == 0) {
if (strncmp (argv[2], "on", 2) == 0) {
sm501_backlight (BL_ON);
@@ -1161,14 +1170,17 @@
sm501_backlight (BL_OFF);
return 0;
}
+#endif
}
break;
+#if defined(CONFIG_STK52XX)
case 4:
if (strcmp (argv[1], "led") == 0) {
return (do_led (argv));
}
break;
+#endif
default:
break;
@@ -1204,7 +1216,9 @@
"[channel]\n"
" - play short beep on \"l\"eft or \"r\"ight channel\n"
);
+#endif /* CONFIG_STK52XX || CONFIG_FO300 */
+#if defined(CONFIG_STK52XX)
U_BOOT_CMD(
fkt , 4, 1, cmd_fkt,
"fkt - Function test routines\n",
@@ -1217,5 +1231,14 @@
"fkt backlight on/off\n"
" - switch backlight on or off\n"
);
-#endif /* CONFIG_STK52XX */
+#elif defined(CONFIG_FO300)
+U_BOOT_CMD(
+ fkt , 3, 1, cmd_fkt,
+ "fkt - Function test routines\n",
+ "fkt can\n"
+ " - loopback plug for X16/X29 required\n"
+ "fkt rs232 number\n"
+ " - loopback plug(s) for X21/X22 required\n"
+);
+#endif
#endif /* CFG_CMD_BSP */
diff --git a/board/tqm5200/tqm5200.c b/board/tqm5200/tqm5200.c
index d6f7737..c8350ab 100644
--- a/board/tqm5200/tqm5200.c
+++ b/board/tqm5200/tqm5200.c
@@ -290,8 +290,10 @@
# define CARRIER_NAME "TB5200"
#elif defined(CONFIG_CAM5200)
# define CARRIER_NAME "Cam5200"
+#elif defined(CONFIG_FO300)
+# define CARRIER_NAME "FO300"
#else
-# error "Unknown carrier board"
+# error "UNKNOWN"
#endif
puts ( "Board: " MODULE_NAME " (TQ-Components GmbH)\n"
@@ -541,7 +543,11 @@
#ifdef CONFIG_VIDEO_SM501
+#ifdef CONFIG_FO300
+#define DISPLAY_WIDTH 800
+#else
#define DISPLAY_WIDTH 640
+#endif
#define DISPLAY_HEIGHT 480
#ifdef CONFIG_VIDEO_SM501_8BPP
@@ -571,6 +577,28 @@
{0x80218, 0x000201e9},
{0x80200, 0x00013306},
#else /* panel + CRT */
+#ifdef CONFIG_FO300
+ {0x00004, 0x0},
+ {0x00048, 0x00021807},
+ {0x0004C, 0x301a0a01},
+ {0x00054, 0x1},
+ {0x00040, 0x00021807},
+ {0x00044, 0x091a0a01},
+ {0x00054, 0x0},
+ {0x80000, 0x0f013106},
+ {0x80004, 0xc428bb17},
+ {0x8000C, 0x00000000},
+ {0x80010, 0x0C800C80},
+ {0x80014, 0x03200000},
+ {0x80018, 0x01e00000},
+ {0x8001C, 0x00000000},
+ {0x80020, 0x01e00320},
+ {0x80024, 0x042a031f},
+ {0x80028, 0x0086034a},
+ {0x8002C, 0x020c01df},
+ {0x80030, 0x000201ea},
+ {0x80200, 0x00010000},
+#else
{0x00004, 0x0},
{0x00048, 0x00021807},
{0x0004C, 0x091a0a01},
@@ -591,6 +619,7 @@
{0x8002C, 0x020c01df},
{0x80030, 0x000201e9},
{0x80200, 0x00010000},
+#endif /* #ifdef CONFIG_FO300 */
#endif
{0, 0}
};
@@ -604,7 +633,7 @@
{
if (line_number == 1) {
strcpy (info, " Board: TQM5200 (TQ-Components GmbH)");
-#if defined (CONFIG_STK52XX) || defined (CONFIG_TB5200)
+#if defined (CONFIG_STK52XX) || defined (CONFIG_TB5200) || defined(CONFIG_FO300)
} else if (line_number == 2) {
#if defined (CONFIG_STK52XX)
strcpy (info, " on a STK52xx carrier board");
@@ -612,6 +641,9 @@
#if defined (CONFIG_TB5200)
strcpy (info, " on a TB5200 carrier board");
#endif
+#if defined (CONFIG_FO300)
+ strcpy (info, " on a FO300 carrier board");
+#endif
#endif
}
else {
@@ -697,3 +729,33 @@
}
#endif /* CONFIG_VIDEO_SM501 */
+
+
+#ifdef CONFIG_BOARD_EARLY_INIT_F
+#ifdef CONFIG_FO300
+int board_early_init_f (void)
+{
+ vu_long timer3_status;
+ DECLARE_GLOBAL_DATA_PTR;
+
+ /* Configure GPT3 as GPIO input */
+ *(vu_long *)MPC5XXX_GPT3_ENABLE = 0x00000004;
+
+ /* Read in TIMER_3 pin status */
+ timer3_status = *(vu_long *)MPC5XXX_GPT3_STATUS;
+
+#ifdef FO300_SILENT_CONSOLE_WHEN_S1_CLOSED
+ /* Force silent console mode if S1 switch
+ * is in closed position (TIMER_3 pin status is LOW). */
+ if (MPC5XXX_GPT_GPIO_PIN(timer3_status) == 0)
+#else
+ /* Force silent console mode if S1 switch
+ * is in open position (TIMER_3 pin status is HIGH). */
+ if (MPC5XXX_GPT_GPIO_PIN(timer3_status) == 1)
+#endif
+ gd->flags |= GD_FLG_SILENT;
+
+ return 0;
+}
+#endif
+#endif
diff --git a/board/trab/trab.c b/board/trab/trab.c
index 26e52d2..d8a726b 100644
--- a/board/trab/trab.c
+++ b/board/trab/trab.c
@@ -175,9 +175,11 @@
#endif /* CONFIG_VERSION_VARIABLE */
#ifdef CONFIG_AUTO_UPDATE
- extern int do_auto_update(void);
- /* this has priority over all else */
- do_auto_update();
+ {
+ extern int do_auto_update(void);
+ /* this has priority over all else */
+ do_auto_update();
+ }
#endif
for (i = 0; i < KEYBD_KEY_NUM; ++i) {
diff --git a/common/cmd_mii.c b/common/cmd_mii.c
index ee5e43e..e659536 100644
--- a/common/cmd_mii.c
+++ b/common/cmd_mii.c
@@ -117,8 +117,6 @@
miiphy_speed (devname, j),
(miiphy_duplex (devname, j) == FULL)
? "FDX" : "HDX");
- } else {
- puts ("Error reading info from the PHY\n");
}
}
} else if (op == 'r') {
@@ -503,8 +501,6 @@
miiphy_speed (devname, j),
(miiphy_duplex (devname, j) == FULL)
? "FDX" : "HDX");
- } else {
- puts ("Error reading info from the PHY\n");
}
}
} else if (op[0] == 'r') {
diff --git a/common/main.c b/common/main.c
index 3788bd5..13d12a4 100644
--- a/common/main.c
+++ b/common/main.c
@@ -937,6 +937,7 @@
#ifdef CONFIG_CMDLINE_EDITING
char *p = console_buffer;
unsigned int len=MAX_CMDBUF_SIZE;
+ int rc;
static int initted = 0;
if (!initted) {
@@ -946,8 +947,8 @@
puts (prompt);
- cread_line(p, &len);
- return len;
+ rc = cread_line(p, &len);
+ return rc < 0 ? rc : len;
#else
char *p = console_buffer;
int n = 0; /* buffer index */
diff --git a/cpu/i386/sc520.c b/cpu/i386/sc520.c
index c83f0bb..1c4370b 100644
--- a/cpu/i386/sc520.c
+++ b/cpu/i386/sc520.c
@@ -31,7 +31,9 @@
#include <common.h>
#include <config.h>
#include <pci.h>
+#ifdef CONFIG_SC520_SSI
#include <ssi.h>
+#endif
#include <asm/io.h>
#include <asm/pci.h>
#include <asm/ic/sc520.h>
@@ -143,7 +145,15 @@
u32 dram_present=0;
u32 dram_ctrl;
-
+#ifdef CFG_SDRAM_DRCTMCTL
+ /* these memory control registers are set up in the assember part,
+ * in sc520_asm.S, during 'mem_init'. If we muck with them here,
+ * after we are running a stack in RAM, we have troubles. Besides,
+ * these refresh and delay values are better ? simply specified
+ * outright in the include/configs/{cfg} file since the HW designer
+ * simply dictates it.
+ */
+#else
int val;
int cas_precharge_delay = CFG_SDRAM_PRECHARGE_DELAY;
@@ -162,6 +172,7 @@
} else {
val = 3; /* 62.4us */
}
+
write_mmcr_byte(SC520_DRCCTL, (read_mmcr_byte(SC520_DRCCTL) & 0xcf) | (val<<4));
val = read_mmcr_byte(SC520_DRCTMCTL);
@@ -181,13 +192,12 @@
val |= 1;
}
write_mmcr_byte(SC520_DRCTMCTL, val);
-
+#endif
/* We read-back the configuration of the dram
* controller that the assembly code wrote */
dram_ctrl = read_mmcr_long(SC520_DRCBENDADR);
-
bd->bi_dram[0].start = 0;
if (dram_ctrl & 0x80) {
/* bank 0 enabled */
@@ -274,7 +284,7 @@
{
int i;
-# if 0
+# if 1
printf("set_irq(): map INT%c to IRQ%d\n", pci_pin + 'A', irq);
#endif
if (irq < 0 || irq > 15) {
diff --git a/cpu/i386/sc520_asm.S b/cpu/i386/sc520_asm.S
index 80464fa..e1fa37a 100644
--- a/cpu/i386/sc520_asm.S
+++ b/cpu/i386/sc520_asm.S
@@ -113,6 +113,7 @@
.equ DRCCFG, 0x0fffef014 /* DRAM bank configuration register */
.equ DRCBENDADR, 0x0fffef018 /* DRAM bank ending address register */
.equ ECCCTL, 0x0fffef020 /* DRAM ECC control register */
+.equ ECCINT, 0x0fffefd18 /* DRAM ECC nmi-INT mapping */
.equ DBCTL, 0x0fffef040 /* DRAM buffer control register */
.equ CACHELINESZ, 0x00000010 /* size of our cache line (read buffer) */
@@ -459,6 +460,12 @@
incl %edi
loop cleanuplp
+#if defined CFG_SDRAM_DRCTMCTL
+ /* just have your hardware desinger _GIVE_ you what you need here! */
+ movl $DRCTMCTL, %edi
+ movb $CFG_SDRAM_DRCTMCTL,%al
+ movb (%edi), %al
+#else
#if defined(CFG_SDRAM_CAS_LATENCY_2T) || defined(CFG_SDRAM_CAS_LATENCY_3T)
/* set the CAS latency now since it is hard to do
* when we run from the RAM */
@@ -470,7 +477,8 @@
#ifdef CFG_SDRAM_CAS_LATENCY_3T
orb $0x10, %al
#endif
- movb %al, (%edi)
+ movb %al, (%edi)
+#endif
#endif
movl $DRCCTL, %edi /* DRAM Control register */
movb $0x3,%al /* Load mode register cmd */
@@ -528,9 +536,49 @@
shll $22, %eax
movl %eax, %ebx
-done: movl %ebx, %eax
+done:
+ movl %ebx, %eax
+
+#if CFG_SDRAM_ECC_ENABLE
+ /* A nominal memory test: just a byte at each address line */
+ movl %eax, %ecx
+ shrl $0x1, %ecx
+ movl $0x1, %edi
+memtest0:
+ movb $0xa5, (%edi)
+ cmpb $0xa5, (%edi)
+ jne out
+ shrl $1, %ecx
+ andl %ecx,%ecx
+ jz set_ecc
+ shll $1, %edi
+ jmp memtest0
+
+set_ecc:
+ /* clear all ram with a memset */
+ movl %eax, %ecx
+ xorl %esi, %esi
+ xorl %edi, %edi
+ xorl %eax, %eax
+ shrl $2, %ecx
+ cld
+ rep stosl
+ /* enable read, write buffers */
+ movb $0x11, %al
+ movl $DBCTL, %edi
+ movb %al, (%edi)
+ /* enable NMI mapping for ECC */
+ movl $ECCINT, %edi
+ mov $0x10, %al
+ movb %al, (%edi)
+ /* Turn on ECC */
+ movl $ECCCTL, %edi
+ mov $0x05, %al
+ movb %al, (%edi)
+#endif
+out:
+ movl %ebx, %eax
jmp *%ebp
-
#endif /* CONFIG_SC520 */
diff --git a/cpu/ppc4xx/405gp_pci.c b/cpu/ppc4xx/405gp_pci.c
index cf5eccb..0b0686b 100644
--- a/cpu/ppc4xx/405gp_pci.c
+++ b/cpu/ppc4xx/405gp_pci.c
@@ -315,7 +315,6 @@
#ifdef CONFIG_PCI_SCAN_SHOW
printf("PCI: Bus Dev VenId DevId Class Int\n");
#endif
-
hose->last_busno = pci_hose_scan(hose);
}
#endif /* CONFIG_PCI_PNP */
@@ -563,10 +562,12 @@
}
}
-
void pci_init_board(void)
{
pci_440_init (&ppc440_hose);
+#if defined(CONFIG_440SPE)
+ pcie_setup_hoses();
+#endif
}
#endif /* CONFIG_440 & CONFIG_PCI */
diff --git a/cpu/ppc4xx/440spe_pcie.c b/cpu/ppc4xx/440spe_pcie.c
new file mode 100644
index 0000000..2e920aa
--- /dev/null
+++ b/cpu/ppc4xx/440spe_pcie.c
@@ -0,0 +1,592 @@
+/*
+ * (C) Copyright 2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * Copyright (c) 2005 Cisco Systems. All rights reserved.
+ * Roland Dreier <rolandd@cisco.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <asm/processor.h>
+#include <asm-ppc/io.h>
+#include <ppc4xx.h>
+#include <common.h>
+#include <pci.h>
+
+#include "440spe_pcie.h"
+
+#if defined(CONFIG_440SPE)
+#if defined(CONFIG_PCI)
+
+enum {
+ PTYPE_ENDPOINT = 0x0,
+ PTYPE_LEGACY_ENDPOINT = 0x1,
+ PTYPE_ROOT_PORT = 0x4,
+
+ LNKW_X1 = 0x1,
+ LNKW_X4 = 0x4,
+ LNKW_X8 = 0x8
+};
+
+static int pcie_read_config(struct pci_controller *hose, unsigned int devfn,
+ int offset, int len, u32 *val) {
+
+ *val = 0;
+ /*
+ * 440SPE implements only one function per port
+ */
+ if (!((PCI_FUNC(devfn) == 0) && (PCI_DEV(devfn) == 1)))
+ return 0;
+
+ devfn = PCI_BDF(0,0,0);
+ offset += devfn << 4;
+
+ switch (len) {
+ case 1:
+ *val = in_8(hose->cfg_data + offset);
+ break;
+ case 2:
+ *val = in_le16((u16 *)(hose->cfg_data + offset));
+ break;
+ default:
+ *val = in_le32((u32 *)(hose->cfg_data + offset));
+ break;
+ }
+ return 0;
+}
+
+static int pcie_write_config(struct pci_controller *hose, unsigned int devfn,
+ int offset, int len, u32 val) {
+
+ /*
+ * 440SPE implements only one function per port
+ */
+ if (!((PCI_FUNC(devfn) == 0) && (PCI_DEV(devfn) == 1)))
+ return 0;
+
+ devfn = PCI_BDF(0,0,0);
+ offset += devfn << 4;
+
+ switch (len) {
+ case 1:
+ out_8(hose->cfg_data + offset, val);
+ break;
+ case 2:
+ out_le16((u16 *)(hose->cfg_data + offset), val);
+ break;
+ default:
+ out_le32((u32 *)(hose->cfg_data + offset), val);
+ break;
+ }
+ return 0;
+}
+
+int pcie_read_config_byte(struct pci_controller *hose,pci_dev_t dev,int offset,u8 *val)
+{
+ u32 v;
+ int rv;
+
+ rv = pcie_read_config(hose, dev, offset, 1, &v);
+ *val = (u8)v;
+ return rv;
+}
+
+int pcie_read_config_word(struct pci_controller *hose,pci_dev_t dev,int offset,u16 *val)
+{
+ u32 v;
+ int rv;
+
+ rv = pcie_read_config(hose, dev, offset, 2, &v);
+ *val = (u16)v;
+ return rv;
+}
+
+int pcie_read_config_dword(struct pci_controller *hose,pci_dev_t dev,int offset,u32 *val)
+{
+ u32 v;
+ int rv;
+
+ rv = pcie_read_config(hose, dev, offset, 3, &v);
+ *val = (u32)v;
+ return rv;
+}
+
+int pcie_write_config_byte(struct pci_controller *hose,pci_dev_t dev,int offset,u8 val)
+{
+ return pcie_write_config(hose,(u32)dev,offset,1,val);
+}
+
+int pcie_write_config_word(struct pci_controller *hose,pci_dev_t dev,int offset,u16 val)
+{
+ return pcie_write_config(hose,(u32)dev,offset,2,(u32 )val);
+}
+
+int pcie_write_config_dword(struct pci_controller *hose,pci_dev_t dev,int offset,u32 val)
+{
+ return pcie_write_config(hose,(u32)dev,offset,3,(u32 )val);
+}
+
+static void ppc440spe_setup_utl(u32 port) {
+
+ volatile void *utl_base = NULL;
+
+ /*
+ * Map UTL registers
+ */
+ switch (port) {
+ case 0:
+ mtdcr(DCRN_PEGPL_REGBAH(PCIE0), 0x0000000c);
+ mtdcr(DCRN_PEGPL_REGBAL(PCIE0), 0x20000000);
+ mtdcr(DCRN_PEGPL_REGMSK(PCIE0), 0x00007001);
+ mtdcr(DCRN_PEGPL_SPECIAL(PCIE0), 0x68782800);
+ break;
+
+ case 1:
+ mtdcr(DCRN_PEGPL_REGBAH(PCIE1), 0x0000000c);
+ mtdcr(DCRN_PEGPL_REGBAL(PCIE1), 0x20001000);
+ mtdcr(DCRN_PEGPL_REGMSK(PCIE1), 0x00007001);
+ mtdcr(DCRN_PEGPL_SPECIAL(PCIE1), 0x68782800);
+ break;
+
+ case 2:
+ mtdcr(DCRN_PEGPL_REGBAH(PCIE2), 0x0000000c);
+ mtdcr(DCRN_PEGPL_REGBAL(PCIE2), 0x20002000);
+ mtdcr(DCRN_PEGPL_REGMSK(PCIE2), 0x00007001);
+ mtdcr(DCRN_PEGPL_SPECIAL(PCIE2), 0x68782800);
+ break;
+ }
+ utl_base = (unsigned int *)(CFG_PCIE_BASE + 0x1000 * port);
+
+ /*
+ * Set buffer allocations and then assert VRB and TXE.
+ */
+ out_be32(utl_base + PEUTL_OUTTR, 0x08000000);
+ out_be32(utl_base + PEUTL_INTR, 0x02000000);
+ out_be32(utl_base + PEUTL_OPDBSZ, 0x10000000);
+ out_be32(utl_base + PEUTL_PBBSZ, 0x53000000);
+ out_be32(utl_base + PEUTL_IPHBSZ, 0x08000000);
+ out_be32(utl_base + PEUTL_IPDBSZ, 0x10000000);
+ out_be32(utl_base + PEUTL_RCIRQEN, 0x00f00000);
+ out_be32(utl_base + PEUTL_PCTL, 0x80800066);
+}
+
+static int check_error(void)
+{
+ u32 valPE0, valPE1, valPE2;
+ int err = 0;
+
+ /* SDR0_PEGPLLLCT1 reset */
+ if (!(valPE0 = SDR_READ(PESDR0_PLLLCT1) & 0x01000000)) {
+ printf("PCIE: SDR0_PEGPLLLCT1 reset error 0x%x\n", valPE0);
+ }
+
+ valPE0 = SDR_READ(PESDR0_RCSSET);
+ valPE1 = SDR_READ(PESDR1_RCSSET);
+ valPE2 = SDR_READ(PESDR2_RCSSET);
+
+ /* SDR0_PExRCSSET rstgu */
+ if (!(valPE0 & 0x01000000) ||
+ !(valPE1 & 0x01000000) ||
+ !(valPE2 & 0x01000000)) {
+ printf("PCIE: SDR0_PExRCSSET rstgu error\n");
+ err = -1;
+ }
+
+ /* SDR0_PExRCSSET rstdl */
+ if (!(valPE0 & 0x00010000) ||
+ !(valPE1 & 0x00010000) ||
+ !(valPE2 & 0x00010000)) {
+ printf("PCIE: SDR0_PExRCSSET rstdl error\n");
+ err = -1;
+ }
+
+ /* SDR0_PExRCSSET rstpyn */
+ if ((valPE0 & 0x00001000) ||
+ (valPE1 & 0x00001000) ||
+ (valPE2 & 0x00001000)) {
+ printf("PCIE: SDR0_PExRCSSET rstpyn error\n");
+ err = -1;
+ }
+
+ /* SDR0_PExRCSSET hldplb */
+ if ((valPE0 & 0x10000000) ||
+ (valPE1 & 0x10000000) ||
+ (valPE2 & 0x10000000)) {
+ printf("PCIE: SDR0_PExRCSSET hldplb error\n");
+ err = -1;
+ }
+
+ /* SDR0_PExRCSSET rdy */
+ if ((valPE0 & 0x00100000) ||
+ (valPE1 & 0x00100000) ||
+ (valPE2 & 0x00100000)) {
+ printf("PCIE: SDR0_PExRCSSET rdy error\n");
+ err = -1;
+ }
+
+ /* SDR0_PExRCSSET shutdown */
+ if ((valPE0 & 0x00000100) ||
+ (valPE1 & 0x00000100) ||
+ (valPE2 & 0x00000100)) {
+ printf("PCIE: SDR0_PExRCSSET shutdown error\n");
+ err = -1;
+ }
+ return err;
+}
+
+/*
+ * Initialize PCI Express core
+ */
+int ppc440spe_init_pcie(void)
+{
+ int time_out = 20;
+
+ /* Set PLL clock receiver to LVPECL */
+ SDR_WRITE(PESDR0_PLLLCT1, SDR_READ(PESDR0_PLLLCT1) | 1 << 28);
+
+ if (check_error())
+ return -1;
+
+ if (!(SDR_READ(PESDR0_PLLLCT2) & 0x10000))
+ {
+ printf("PCIE: PESDR_PLLCT2 resistance calibration failed (0x%08x)\n",
+ SDR_READ(PESDR0_PLLLCT2));
+ return -1;
+ }
+ /* De-assert reset of PCIe PLL, wait for lock */
+ SDR_WRITE(PESDR0_PLLLCT1, SDR_READ(PESDR0_PLLLCT1) & ~(1 << 24));
+ udelay(3);
+
+ while(time_out) {
+ if (!(SDR_READ(PESDR0_PLLLCT3) & 0x10000000)) {
+ time_out--;
+ udelay(1);
+ } else
+ break;
+ }
+ if (!time_out) {
+ printf("PCIE: VCO output not locked\n");
+ return -1;
+ }
+ return 0;
+}
+
+int ppc440spe_init_pcie_rootport(int port)
+{
+ static int core_init;
+ volatile u32 val = 0;
+ int attempts;
+
+ if (!core_init) {
+ ++core_init;
+ if (ppc440spe_init_pcie())
+ return -1;
+ }
+
+ /*
+ * Initialize various parts of the PCI Express core for our port:
+ *
+ * - Set as a root port and enable max width
+ * (PXIE0 -> X8, PCIE1 and PCIE2 -> X4).
+ * - Set up UTL configuration.
+ * - Increase SERDES drive strength to levels suggested by AMCC.
+ * - De-assert RSTPYN, RSTDL and RSTGU.
+ *
+ * NOTICE for revB chip: PESDRn_UTLSET2 is not set - we leave it with
+ * default setting 0x11310000. The register has new fields,
+ * PESDRn_UTLSET2[LKINE] in particular: clearing it leads to PCIE core
+ * hang.
+ */
+ switch (port) {
+ case 0:
+ SDR_WRITE(PESDR0_DLPSET, 1 << 24 | PTYPE_ROOT_PORT << 20 | LNKW_X8 << 12);
+
+ SDR_WRITE(PESDR0_UTLSET1, 0x21222222);
+ if (!ppc440spe_revB())
+ SDR_WRITE(PESDR0_UTLSET2, 0x11000000);
+ SDR_WRITE(PESDR0_HSSL0SET1, 0x35000000);
+ SDR_WRITE(PESDR0_HSSL1SET1, 0x35000000);
+ SDR_WRITE(PESDR0_HSSL2SET1, 0x35000000);
+ SDR_WRITE(PESDR0_HSSL3SET1, 0x35000000);
+ SDR_WRITE(PESDR0_HSSL4SET1, 0x35000000);
+ SDR_WRITE(PESDR0_HSSL5SET1, 0x35000000);
+ SDR_WRITE(PESDR0_HSSL6SET1, 0x35000000);
+ SDR_WRITE(PESDR0_HSSL7SET1, 0x35000000);
+ SDR_WRITE(PESDR0_RCSSET,
+ (SDR_READ(PESDR0_RCSSET) & ~(1 << 24 | 1 << 16)) | 1 << 12);
+ break;
+
+ case 1:
+ SDR_WRITE(PESDR1_DLPSET, 1 << 24 | PTYPE_ROOT_PORT << 20 | LNKW_X4 << 12);
+ SDR_WRITE(PESDR1_UTLSET1, 0x21222222);
+ if (!ppc440spe_revB())
+ SDR_WRITE(PESDR1_UTLSET2, 0x11000000);
+ SDR_WRITE(PESDR1_HSSL0SET1, 0x35000000);
+ SDR_WRITE(PESDR1_HSSL1SET1, 0x35000000);
+ SDR_WRITE(PESDR1_HSSL2SET1, 0x35000000);
+ SDR_WRITE(PESDR1_HSSL3SET1, 0x35000000);
+ SDR_WRITE(PESDR1_RCSSET,
+ (SDR_READ(PESDR1_RCSSET) & ~(1 << 24 | 1 << 16)) | 1 << 12);
+ break;
+
+ case 2:
+ SDR_WRITE(PESDR2_DLPSET, 1 << 24 | PTYPE_ROOT_PORT << 20 | LNKW_X4 << 12);
+ SDR_WRITE(PESDR2_UTLSET1, 0x21222222);
+ if (!ppc440spe_revB())
+ SDR_WRITE(PESDR2_UTLSET2, 0x11000000);
+ SDR_WRITE(PESDR2_HSSL0SET1, 0x35000000);
+ SDR_WRITE(PESDR2_HSSL1SET1, 0x35000000);
+ SDR_WRITE(PESDR2_HSSL2SET1, 0x35000000);
+ SDR_WRITE(PESDR2_HSSL3SET1, 0x35000000);
+ SDR_WRITE(PESDR2_RCSSET,
+ (SDR_READ(PESDR2_RCSSET) & ~(1 << 24 | 1 << 16)) | 1 << 12);
+ break;
+ }
+ /*
+ * Notice: the following delay has critical impact on device
+ * initialization - if too short (<50ms) the link doesn't get up.
+ */
+ mdelay(100);
+
+ switch (port) {
+ case 0: val = SDR_READ(PESDR0_RCSSTS); break;
+ case 1: val = SDR_READ(PESDR1_RCSSTS); break;
+ case 2: val = SDR_READ(PESDR2_RCSSTS); break;
+ }
+
+ if (val & (1 << 20)) {
+ printf("PCIE%d: PGRST failed %08x\n", port, val);
+ return -1;
+ }
+
+ /*
+ * Verify link is up
+ */
+ val = 0;
+ switch (port)
+ {
+ case 0:
+ val = SDR_READ(PESDR0_LOOP);
+ break;
+ case 1:
+ val = SDR_READ(PESDR1_LOOP);
+ break;
+ case 2:
+ val = SDR_READ(PESDR2_LOOP);
+ break;
+ }
+ if (!(val & 0x00001000)) {
+ printf("PCIE%d: link is not up.\n", port);
+ return -1;
+ }
+
+ /*
+ * Setup UTL registers - but only on revA!
+ * We use default settings for revB chip.
+ */
+ if (!ppc440spe_revB())
+ ppc440spe_setup_utl(port);
+
+ /*
+ * We map PCI Express configuration access into the 512MB regions
+ *
+ * NOTICE: revB is very strict about PLB real addressess and ranges to
+ * be mapped for config space; it seems to only work with d_nnnn_nnnn
+ * range (hangs the core upon config transaction attempts when set
+ * otherwise) while revA uses c_nnnn_nnnn.
+ *
+ * For revA:
+ * PCIE0: 0xc_4000_0000
+ * PCIE1: 0xc_8000_0000
+ * PCIE2: 0xc_c000_0000
+ *
+ * For revB:
+ * PCIE0: 0xd_0000_0000
+ * PCIE1: 0xd_2000_0000
+ * PCIE2: 0xd_4000_0000
+ */
+
+ switch (port) {
+ case 0:
+ if (ppc440spe_revB()) {
+ mtdcr(DCRN_PEGPL_CFGBAH(PCIE0), 0x0000000d);
+ mtdcr(DCRN_PEGPL_CFGBAL(PCIE0), 0x00000000);
+ } else {
+ /* revA */
+ mtdcr(DCRN_PEGPL_CFGBAH(PCIE0), 0x0000000c);
+ mtdcr(DCRN_PEGPL_CFGBAL(PCIE0), 0x40000000);
+ }
+ mtdcr(DCRN_PEGPL_CFGMSK(PCIE0), 0xe0000001); /* 512MB region, valid */
+ break;
+
+ case 1:
+ if (ppc440spe_revB()) {
+ mtdcr(DCRN_PEGPL_CFGBAH(PCIE1), 0x0000000d);
+ mtdcr(DCRN_PEGPL_CFGBAL(PCIE1), 0x20000000);
+ } else {
+ mtdcr(DCRN_PEGPL_CFGBAH(PCIE1), 0x0000000c);
+ mtdcr(DCRN_PEGPL_CFGBAL(PCIE1), 0x80000000);
+ }
+ mtdcr(DCRN_PEGPL_CFGMSK(PCIE1), 0xe0000001); /* 512MB region, valid */
+ break;
+
+ case 2:
+ if (ppc440spe_revB()) {
+ mtdcr(DCRN_PEGPL_CFGBAH(PCIE2), 0x0000000d);
+ mtdcr(DCRN_PEGPL_CFGBAL(PCIE2), 0x40000000);
+ } else {
+ mtdcr(DCRN_PEGPL_CFGBAH(PCIE2), 0x0000000c);
+ mtdcr(DCRN_PEGPL_CFGBAL(PCIE2), 0xc0000000);
+ }
+ mtdcr(DCRN_PEGPL_CFGMSK(PCIE2), 0xe0000001); /* 512MB region, valid */
+ break;
+ }
+
+ /*
+ * Check for VC0 active and assert RDY.
+ */
+ attempts = 10;
+ switch (port) {
+ case 0:
+ while(!(SDR_READ(PESDR0_RCSSTS) & (1 << 16))) {
+ if (!(attempts--)) {
+ printf("PCIE0: VC0 not active\n");
+ return -1;
+ }
+ mdelay(1000);
+ }
+ SDR_WRITE(PESDR0_RCSSET, SDR_READ(PESDR0_RCSSET) | 1 << 20);
+ break;
+ case 1:
+ while(!(SDR_READ(PESDR1_RCSSTS) & (1 << 16))) {
+ if (!(attempts--)) {
+ printf("PCIE1: VC0 not active\n");
+ return -1;
+ }
+ mdelay(1000);
+ }
+
+ SDR_WRITE(PESDR1_RCSSET, SDR_READ(PESDR1_RCSSET) | 1 << 20);
+ break;
+ case 2:
+ while(!(SDR_READ(PESDR2_RCSSTS) & (1 << 16))) {
+ if (!(attempts--)) {
+ printf("PCIE2: VC0 not active\n");
+ return -1;
+ }
+ mdelay(1000);
+ }
+
+ SDR_WRITE(PESDR2_RCSSET, SDR_READ(PESDR2_RCSSET) | 1 << 20);
+ break;
+ }
+ mdelay(100);
+
+ return 0;
+}
+
+void ppc440spe_setup_pcie(struct pci_controller *hose, int port)
+{
+ volatile void *mbase = NULL;
+
+ pci_set_ops(hose,
+ pcie_read_config_byte,
+ pcie_read_config_word,
+ pcie_read_config_dword,
+ pcie_write_config_byte,
+ pcie_write_config_word,
+ pcie_write_config_dword);
+
+ switch(port) {
+ case 0:
+ mbase = (u32 *)CFG_PCIE0_XCFGBASE;
+ hose->cfg_data = (u8 *)CFG_PCIE0_CFGBASE;
+ break;
+ case 1:
+ mbase = (u32 *)CFG_PCIE1_XCFGBASE;
+ hose->cfg_data = (u8 *)CFG_PCIE1_CFGBASE;
+ break;
+ case 2:
+ mbase = (u32 *)CFG_PCIE2_XCFGBASE;
+ hose->cfg_data = (u8 *)CFG_PCIE2_CFGBASE;
+ break;
+ }
+
+ /*
+ * Set bus numbers on our root port
+ */
+ if (ppc440spe_revB()) {
+ out_8((u8 *)mbase + PCI_PRIMARY_BUS, 0);
+ out_8((u8 *)mbase + PCI_SECONDARY_BUS, 1);
+ out_8((u8 *)mbase + PCI_SUBORDINATE_BUS, 1);
+ } else {
+ out_8((u8 *)mbase + PCI_PRIMARY_BUS, 0);
+ out_8((u8 *)mbase + PCI_SECONDARY_BUS, 0);
+ }
+
+ /*
+ * Set up outbound translation to hose->mem_space from PLB
+ * addresses at an offset of 0xd_0000_0000. We set the low
+ * bits of the mask to 11 to turn off splitting into 8
+ * subregions and to enable the outbound translation.
+ */
+ out_le32(mbase + PECFG_POM0LAH, 0x00000000);
+ out_le32(mbase + PECFG_POM0LAL, (CFG_PCIE_MEMBASE +
+ port * CFG_PCIE_MEMSIZE));
+
+ switch (port) {
+ case 0:
+ mtdcr(DCRN_PEGPL_OMR1BAH(PCIE0), 0x0000000d);
+ mtdcr(DCRN_PEGPL_OMR1BAL(PCIE0), CFG_PCIE_MEMBASE +
+ port * CFG_PCIE_MEMSIZE);
+ mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE0), 0x7fffffff);
+ mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE0),
+ ~(CFG_PCIE_MEMSIZE - 1) | 3);
+ break;
+ case 1:
+ mtdcr(DCRN_PEGPL_OMR1BAH(PCIE1), 0x0000000d);
+ mtdcr(DCRN_PEGPL_OMR1BAL(PCIE1), (CFG_PCIE_MEMBASE +
+ port * CFG_PCIE_MEMSIZE));
+ mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE1), 0x7fffffff);
+ mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE1),
+ ~(CFG_PCIE_MEMSIZE - 1) | 3);
+ break;
+ case 2:
+ mtdcr(DCRN_PEGPL_OMR1BAH(PCIE2), 0x0000000d);
+ mtdcr(DCRN_PEGPL_OMR1BAL(PCIE2), (CFG_PCIE_MEMBASE +
+ port * CFG_PCIE_MEMSIZE));
+ mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE2), 0x7fffffff);
+ mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE2),
+ ~(CFG_PCIE_MEMSIZE - 1) | 3);
+ break;
+ }
+
+ /* Set up 16GB inbound memory window at 0 */
+ out_le32(mbase + PCI_BASE_ADDRESS_0, 0);
+ out_le32(mbase + PCI_BASE_ADDRESS_1, 0);
+ out_le32(mbase + PECFG_BAR0HMPA, 0x7fffffc);
+ out_le32(mbase + PECFG_BAR0LMPA, 0);
+ out_le32(mbase + PECFG_PIM0LAL, 0);
+ out_le32(mbase + PECFG_PIM0LAH, 0);
+ out_le32(mbase + PECFG_PIMEN, 0x1);
+
+ /* Enable I/O, Mem, and Busmaster cycles */
+ out_le16((u16 *)(mbase + PCI_COMMAND),
+ in_le16((u16 *)(mbase + PCI_COMMAND)) |
+ PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
+}
+#endif /* CONFIG_PCI */
+#endif /* CONFIG_440SPE */
diff --git a/cpu/ppc4xx/440spe_pcie.h b/cpu/ppc4xx/440spe_pcie.h
new file mode 100644
index 0000000..47df762
--- /dev/null
+++ b/cpu/ppc4xx/440spe_pcie.h
@@ -0,0 +1,162 @@
+/*
+ * Copyright (c) 2005 Cisco Systems. All rights reserved.
+ * Roland Dreier <rolandd@cisco.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <ppc4xx.h>
+#ifndef __440SPE_PCIE_H
+#define __440SPE_PCIE_H
+
+#define mdelay(n) ({unsigned long __ms=(n); while (__ms--) udelay(1000);})
+
+#define DCRN_SDR0_CFGADDR 0x00e
+#define DCRN_SDR0_CFGDATA 0x00f
+
+#define DCRN_PCIE0_BASE 0x100
+#define DCRN_PCIE1_BASE 0x120
+#define DCRN_PCIE2_BASE 0x140
+#define PCIE0 DCRN_PCIE0_BASE
+#define PCIE1 DCRN_PCIE1_BASE
+#define PCIE2 DCRN_PCIE2_BASE
+
+#define DCRN_PEGPL_CFGBAH(base) (base + 0x00)
+#define DCRN_PEGPL_CFGBAL(base) (base + 0x01)
+#define DCRN_PEGPL_CFGMSK(base) (base + 0x02)
+#define DCRN_PEGPL_MSGBAH(base) (base + 0x03)
+#define DCRN_PEGPL_MSGBAL(base) (base + 0x04)
+#define DCRN_PEGPL_MSGMSK(base) (base + 0x05)
+#define DCRN_PEGPL_OMR1BAH(base) (base + 0x06)
+#define DCRN_PEGPL_OMR1BAL(base) (base + 0x07)
+#define DCRN_PEGPL_OMR1MSKH(base) (base + 0x08)
+#define DCRN_PEGPL_OMR1MSKL(base) (base + 0x09)
+#define DCRN_PEGPL_REGBAH(base) (base + 0x12)
+#define DCRN_PEGPL_REGBAL(base) (base + 0x13)
+#define DCRN_PEGPL_REGMSK(base) (base + 0x14)
+#define DCRN_PEGPL_SPECIAL(base) (base + 0x15)
+
+/*
+ * System DCRs (SDRs)
+ */
+#define PESDR0_PLLLCT1 0x03a0
+#define PESDR0_PLLLCT2 0x03a1
+#define PESDR0_PLLLCT3 0x03a2
+
+#define PESDR0_UTLSET1 0x0300
+#define PESDR0_UTLSET2 0x0301
+#define PESDR0_DLPSET 0x0302
+#define PESDR0_LOOP 0x0303
+#define PESDR0_RCSSET 0x0304
+#define PESDR0_RCSSTS 0x0305
+#define PESDR0_HSSL0SET1 0x0306
+#define PESDR0_HSSL0SET2 0x0307
+#define PESDR0_HSSL0STS 0x0308
+#define PESDR0_HSSL1SET1 0x0309
+#define PESDR0_HSSL1SET2 0x030a
+#define PESDR0_HSSL1STS 0x030b
+#define PESDR0_HSSL2SET1 0x030c
+#define PESDR0_HSSL2SET2 0x030d
+#define PESDR0_HSSL2STS 0x030e
+#define PESDR0_HSSL3SET1 0x030f
+#define PESDR0_HSSL3SET2 0x0310
+#define PESDR0_HSSL3STS 0x0311
+#define PESDR0_HSSL4SET1 0x0312
+#define PESDR0_HSSL4SET2 0x0313
+#define PESDR0_HSSL4STS 0x0314
+#define PESDR0_HSSL5SET1 0x0315
+#define PESDR0_HSSL5SET2 0x0316
+#define PESDR0_HSSL5STS 0x0317
+#define PESDR0_HSSL6SET1 0x0318
+#define PESDR0_HSSL6SET2 0x0319
+#define PESDR0_HSSL6STS 0x031a
+#define PESDR0_HSSL7SET1 0x031b
+#define PESDR0_HSSL7SET2 0x031c
+#define PESDR0_HSSL7STS 0x031d
+#define PESDR0_HSSCTLSET 0x031e
+#define PESDR0_LANE_ABCD 0x031f
+#define PESDR0_LANE_EFGH 0x0320
+
+#define PESDR1_UTLSET1 0x0340
+#define PESDR1_UTLSET2 0x0341
+#define PESDR1_DLPSET 0x0342
+#define PESDR1_LOOP 0x0343
+#define PESDR1_RCSSET 0x0344
+#define PESDR1_RCSSTS 0x0345
+#define PESDR1_HSSL0SET1 0x0346
+#define PESDR1_HSSL0SET2 0x0347
+#define PESDR1_HSSL0STS 0x0348
+#define PESDR1_HSSL1SET1 0x0349
+#define PESDR1_HSSL1SET2 0x034a
+#define PESDR1_HSSL1STS 0x034b
+#define PESDR1_HSSL2SET1 0x034c
+#define PESDR1_HSSL2SET2 0x034d
+#define PESDR1_HSSL2STS 0x034e
+#define PESDR1_HSSL3SET1 0x034f
+#define PESDR1_HSSL3SET2 0x0350
+#define PESDR1_HSSL3STS 0x0351
+#define PESDR1_HSSCTLSET 0x0352
+#define PESDR1_LANE_ABCD 0x0353
+
+#define PESDR2_UTLSET1 0x0370
+#define PESDR2_UTLSET2 0x0371
+#define PESDR2_DLPSET 0x0372
+#define PESDR2_LOOP 0x0373
+#define PESDR2_RCSSET 0x0374
+#define PESDR2_RCSSTS 0x0375
+#define PESDR2_HSSL0SET1 0x0376
+#define PESDR2_HSSL0SET2 0x0377
+#define PESDR2_HSSL0STS 0x0378
+#define PESDR2_HSSL1SET1 0x0379
+#define PESDR2_HSSL1SET2 0x037a
+#define PESDR2_HSSL1STS 0x037b
+#define PESDR2_HSSL2SET1 0x037c
+#define PESDR2_HSSL2SET2 0x037d
+#define PESDR2_HSSL2STS 0x037e
+#define PESDR2_HSSL3SET1 0x037f
+#define PESDR2_HSSL3SET2 0x0380
+#define PESDR2_HSSL3STS 0x0381
+#define PESDR2_HSSCTLSET 0x0382
+#define PESDR2_LANE_ABCD 0x0383
+
+/*
+ * UTL register offsets
+ */
+#define PEUTL_PBBSZ 0x20
+#define PEUTL_OPDBSZ 0x68
+#define PEUTL_IPHBSZ 0x70
+#define PEUTL_IPDBSZ 0x78
+#define PEUTL_OUTTR 0x90
+#define PEUTL_INTR 0x98
+#define PEUTL_PCTL 0xa0
+#define PEUTL_RCIRQEN 0xb8
+
+/*
+ * Config space register offsets
+ */
+#define PECFG_BAR0LMPA 0x210
+#define PECFG_BAR0HMPA 0x214
+#define PECFG_PIMEN 0x33c
+#define PECFG_PIM0LAL 0x340
+#define PECFG_PIM0LAH 0x344
+#define PECFG_POM0LAL 0x380
+#define PECFG_POM0LAH 0x384
+
+#define SDR_READ(offset) ({\
+ mtdcr(DCRN_SDR0_CFGADDR, offset); \
+ mfdcr(DCRN_SDR0_CFGDATA);})
+
+#define SDR_WRITE(offset, data) ({\
+ mtdcr(DCRN_SDR0_CFGADDR, offset); \
+ mtdcr(DCRN_SDR0_CFGDATA,data);})
+
+int ppc440spe_init_pcie(void);
+int ppc440spe_init_pcie_rootport(int port);
+void yucca_setup_pcie_fpga_rootpoint(int port);
+void ppc440spe_setup_pcie(struct pci_controller *hose, int port);
+int yucca_pcie_card_present(int port);
+int pcie_hose_scan(struct pci_controller *hose, int bus);
+#endif /* __440SPE_PCIE_H */
diff --git a/cpu/ppc4xx/Makefile b/cpu/ppc4xx/Makefile
index c563457..7d6990f 100644
--- a/cpu/ppc4xx/Makefile
+++ b/cpu/ppc4xx/Makefile
@@ -31,7 +31,8 @@
bedbug_405.o commproc.o \
cpu.o cpu_init.o i2c.o interrupts.o \
miiphy.o sdram.o serial.o \
- spd_sdram.o speed.o traps.o usb_ohci.o usbdev.o
+ spd_sdram.o speed.o traps.o usb_ohci.o usbdev.o \
+ 440spe_pcie.o
OBJS = $(AOBJS) $(COBJS)
diff --git a/cpu/ppc4xx/cpu.c b/cpu/ppc4xx/cpu.c
index 71303bc..bc51fbf 100644
--- a/cpu/ppc4xx/cpu.c
+++ b/cpu/ppc4xx/cpu.c
@@ -315,6 +315,17 @@
return 0;
}
+#if defined (CONFIG_440SPE)
+int ppc440spe_revB() {
+ unsigned int pvr;
+
+ pvr = get_pvr();
+ if (pvr == PVR_440SPe_RB)
+ return 1;
+ else
+ return 0;
+}
+#endif
/* ------------------------------------------------------------------------- */
diff --git a/cpu/ppc4xx/start.S b/cpu/ppc4xx/start.S
index 699fa7f..60ed2d5 100644
--- a/cpu/ppc4xx/start.S
+++ b/cpu/ppc4xx/start.S
@@ -315,7 +315,23 @@
/*----------------------------------------------------------------*/
/* TLB entry setup -- step thru tlbtab */
/*----------------------------------------------------------------*/
+#if defined(CONFIG_440SPE)
+ /*----------------------------------------------------------------*/
+ /* We have different TLB tables for revA and rev B of 440SPe */
+ /*----------------------------------------------------------------*/
+ mfspr r1, PVR
+ lis r0,0x5342
+ ori r0,r0,0x1891
+ cmpw r7,r1,r0
+ bne r7,..revA
+ bl tlbtabB
+ b ..goon
+..revA:
+ bl tlbtabA
+..goon:
+#else
bl tlbtab /* Get tlbtab pointer */
+#endif
mr r5,r0
li r1,0x003f /* 64 TLB entries max */
mtctr r1
diff --git a/drivers/dm9000x.c b/drivers/dm9000x.c
index 0e475d4..6877076 100644
--- a/drivers/dm9000x.c
+++ b/drivers/dm9000x.c
@@ -436,6 +436,9 @@
u8 rxbyte, *rdptr = (u8 *) NetRxPackets[0];
u16 RxStatus, RxLen = 0;
u32 tmplen, i;
+#ifdef CONFIG_DM9000_USE_32BIT
+ u32 tmpdata;
+#endif
/* Check packet ready or not */
DM9000_ior(DM9000_MRCMDX); /* Dummy read */
diff --git a/include/common.h b/include/common.h
index 9da66b8..8000dd0 100644
--- a/include/common.h
+++ b/include/common.h
@@ -252,6 +252,9 @@
void pci_master_init (struct pci_controller *);
# endif
int is_pci_host (struct pci_controller *);
+#if defined(CONFIG_440SPE)
+ void pcie_setup_hoses(void);
+#endif
#endif
int misc_init_f (void);
@@ -474,6 +477,7 @@
# if defined(CONFIG_440SPE)
unsigned long determine_sysper(void);
unsigned long determine_pci_clock_per(void);
+ int ppc440spe_revB(void);
# endif
# else
typedef PPC405_SYS_INFO sys_info_t;
@@ -611,7 +615,7 @@
#endif
#ifdef CONFIG_INIT_CRITICAL
-#error CONFIG_INIT_CRITICAL is depracted!
+#error CONFIG_INIT_CRITICAL is deprecated!
#error Read section CONFIG_SKIP_LOWLEVEL_INIT in README.
#endif
diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h
index be83b67..31e3eed 100644
--- a/include/configs/TQM5200.h
+++ b/include/configs/TQM5200.h
@@ -37,7 +37,8 @@
#define CONFIG_TQM5200 1 /* ... on TQM5200 module */
#undef CONFIG_TQM5200_REV100 /* define for revision 100 modules */
-#ifndef CONFIG_CAM5200 /* On a Cameron board or ... */
+/* On a Cameron or on a FO300 board or ... */
+#if !defined(CONFIG_CAM5200) && !defined(CONFIG_FO300)
#define CONFIG_STK52XX 1 /* ... on a STK52XX board */
#endif
@@ -58,6 +59,20 @@
#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
+#ifdef CONFIG_FO300
+#define CFG_DEVICE_NULLDEV 1 /* enable null device */
+#define CONFIG_SILENT_CONSOLE 1 /* enable silent startup */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* used to detect S1 switch position */
+
+#if 0
+#define FO300_SILENT_CONSOLE_WHEN_S1_CLOSED 1 /* silent console on PSC1 when S1 */
+ /* switch is closed */
+#endif
+
+#undef FO300_SILENT_CONSOLE_WHEN_S1_CLOSED /* silent console on PSC1 when S1 */
+ /* switch is open */
+#endif /* CONFIG_FO300 */
+
#ifdef CONFIG_STK52XX
#define CONFIG_PS2KBD /* AT-PS/2 Keyboard */
#define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */
@@ -105,12 +120,18 @@
#define CONFIG_VIDEO_SM501_32BPP
#define CONFIG_CFB_CONSOLE
#define CONFIG_VIDEO_LOGO
-#define CONFIG_VGA_AS_SINGLE_DEVICE
+
+#ifndef CONFIG_FO300
#define CONFIG_CONSOLE_EXTRA_INFO
+#else
+#define CONFIG_VIDEO_BMP_LOGO
+#endif
+
+#define CONFIG_VGA_AS_SINGLE_DEVICE
#define CONFIG_VIDEO_SW_CURSOR
#define CONFIG_SPLASH_SCREEN
#define CFG_CONSOLE_IS_IN_ENV
-#endif
+#endif /* #ifndef CONFIG_TQM5200S */
#ifdef CONFIG_VIDEO
#define ADD_BMP_CMD CFG_CMD_BMP
@@ -124,7 +145,7 @@
#define CONFIG_ISO_PARTITION
/* USB */
-#ifdef CONFIG_STK52XX
+#if defined(CONFIG_STK52XX) || defined(CONFIG_FO300)
#define CONFIG_USB_OHCI
#define ADD_USB_CMD CFG_CMD_USB | CFG_CMD_FAT
#define CONFIG_USB_STORAGE
@@ -148,7 +169,7 @@
#endif
/* IDE */
-#if defined (CONFIG_MINIFAP) || defined (CONFIG_STK52XX)
+#if defined (CONFIG_MINIFAP) || defined (CONFIG_STK52XX) || defined(CONFIG_FO300)
#define ADD_IDE_CMD (CFG_CMD_IDE | CFG_CMD_FAT | CFG_CMD_EXT2)
#else
#define ADD_IDE_CMD 0
@@ -224,6 +245,12 @@
"erase FC000000 FC03FFFF;" \
"cp.b 200000 FC000000 ${filesize};" \
"protect on FC000000 FC03FFFF\0"
+#elif defined (CONFIG_FO300)
+# define ENV_UPDT \
+ "update=protect off FC000000 FC05FFFF;" \
+ "erase FC000000 FC05FFFF;" \
+ "cp.b 200000 FC000000 ${filesize};" \
+ "protect on FC000000 FC05FFFF\0"
#else
# error "Unknown Carrier Board"
#endif /* CONFIG_STK52XX */
@@ -378,6 +405,13 @@
"2m(initrd)," \
"8m(misc)," \
"16m(big-fs)"
+#elif defined (CONFIG_FO300)
+# define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:640k(firmware)," \
+ "1408k(kernel)," \
+ "2m(initrd)," \
+ "4m(small-fs)," \
+ "8m(misc)," \
+ "16m(big-fs)"
#else
# error "Unknown Carrier Board"
#endif /* CONFIG_STK52XX */
@@ -450,15 +484,18 @@
* use ALT CAN position: Bits 2-3 (mask: 0x30000000):
* 00 -> No Alternatives, CAN1/2 on PSC2 according to PSC2 setting.
* 01 -> CAN1 on I2C1, CAN2 on Tmr0/1.
- * Use for REV200 STK52XX boards. Do not use with REV100 modules
- * (because, there I2C1 is used as I2C bus)
+ * Use for REV200 STK52XX boards and FO300 boards. Do not use
+ * with REV100 modules (because, there I2C1 is used as I2C bus)
* use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100
* use PSC2 as CAN: Bits 25:27 (mask: 0x00000030)
* 000 -> All PSC2 pins are GIOPs
* 001 -> CAN1/2 on PSC2 pins
* Use for REV100 STK52xx boards
+ * 01x -> Use AC97
+ * use PSC3: Bits 20-23 (mask: 0x00000f00)
+ * 1100 -> UART/SPI (on FO300 board)
* use PSC6:
- * on STK52xx:
+ * on STK52xx and FO300:
* use as UART. Pins PSC6_0 to PSC6_3 are used.
* Bits 9:11 (mask: 0x00700000):
* 101 -> PSC6 : Extended POST test is not available
@@ -480,6 +517,8 @@
# define CFG_GPS_PORT_CONFIG 0x91500004
# endif
# endif
+#elif defined (CONFIG_FO300)
+# define CFG_GPS_PORT_CONFIG 0x91502c24
#else /* TMQ5200 Inbetriebnahme-Board */
# define CFG_GPS_PORT_CONFIG 0x81000004
#endif
diff --git a/include/configs/TQM834x.h b/include/configs/TQM834x.h
index cec7e3e..92c7016 100644
--- a/include/configs/TQM834x.h
+++ b/include/configs/TQM834x.h
@@ -422,9 +422,9 @@
#define CFG_SICRL SICRL_LDP_A
/* i-cache and d-cache disabled */
-#define CFG_HID0_INIT 0x000000000
-#define CFG_HID0_FINAL CFG_HID0_INIT
-#define CFG_HID2 0x000000000
+#define CFG_HID0_INIT 0x000000000
+#define CFG_HID0_FINAL CFG_HID0_INIT
+#define CFG_HID2 HID2_HBE
/* DDR 0 - 512M */
#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
@@ -437,12 +437,21 @@
#define CFG_IBAT2U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
/* PCI */
-#define CFG_IBAT3L (CFG_PCI1_MEM_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#ifdef CONFIG_PCI
+#define CFG_IBAT3L (CFG_PCI1_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CFG_IBAT3U (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_IBAT4L (CFG_PCI1_MEM_BASE + 0x10000000 | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT4L (CFG_PCI1_MEM_BASE + 0x10000000 | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CFG_IBAT4U (CFG_PCI1_MEM_BASE + 0x10000000 | BATU_BL_256M | BATU_VS | BATU_VP)
#define CFG_IBAT5L (CFG_PCI1_IO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CFG_IBAT5U (CFG_PCI1_IO_BASE + 0x10000000 | BATU_BL_16M | BATU_VS | BATU_VP)
+#else
+#define CFG_IBAT3L (0)
+#define CFG_IBAT3U (0)
+#define CFG_IBAT4L (0)
+#define CFG_IBAT4U (0)
+#define CFG_IBAT5L (0)
+#define CFG_IBAT5U (0)
+#endif
/* IMMRBAR */
#define CFG_IBAT6L (CFG_IMMRBAR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h
index 780f274..bc3b9aa 100644
--- a/include/configs/TQM85xx.h
+++ b/include/configs/TQM85xx.h
@@ -424,7 +424,7 @@
#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */
#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
@@ -449,7 +449,7 @@
"run nfsargs addip addcons;bootm\0" \
"rootpath=/opt/eldk/ppc_85xx\0" \
"kernel_addr=FE000000\0" \
- "ramdisk_addr=FE100000\0" \
+ "ramdisk_addr=FE180000\0" \
"load=tftp 100000 /tftpboot/$hostname/u-boot.bin\0" \
"update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
"cp.b 100000 fffc0000 40000;" \
diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h
index 2c1c319..cd4339b 100644
--- a/include/configs/bamboo.h
+++ b/include/configs/bamboo.h
@@ -310,11 +310,11 @@
#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
CFG_CMD_ASKENV | \
- CFG_CMD_EEPROM | \
CFG_CMD_DATE | \
CFG_CMD_DHCP | \
CFG_CMD_DIAG | \
CFG_CMD_ELF | \
+ CFG_CMD_EEPROM | \
CFG_CMD_I2C | \
CFG_CMD_IRQ | \
CFG_CMD_MII | \
@@ -358,13 +358,11 @@
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-#define CONFIG_CMDLINE_EDITING
-
-#ifdef CONFIG_CMDLINE_EDITING
-#undef CONFIG_AUTO_COMPLETE
-#else
-#define CONFIG_AUTO_COMPLETE
-#endif
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
/*-----------------------------------------------------------------------
* PCI stuff
diff --git a/include/configs/bubinga.h b/include/configs/bubinga.h
index 4a79835..a66cdc3 100644
--- a/include/configs/bubinga.h
+++ b/include/configs/bubinga.h
@@ -200,8 +200,9 @@
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
diff --git a/include/configs/ebony.h b/include/configs/ebony.h
index a26af69..d8882ea 100644
--- a/include/configs/ebony.h
+++ b/include/configs/ebony.h
@@ -143,7 +143,13 @@
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+
+#define CFG_I2C_MULTI_EEPROMS
+#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#define CFG_EEPROM_PAGE_WRITE_BITS 3
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
#define CONFIG_PREBOOT "echo;" \
"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
@@ -205,6 +211,7 @@
CFG_CMD_DHCP | \
CFG_CMD_DIAG | \
CFG_CMD_ELF | \
+ CFG_CMD_EEPROM | \
CFG_CMD_I2C | \
CFG_CMD_IRQ | \
CFG_CMD_MII | \
@@ -243,8 +250,9 @@
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
diff --git a/include/configs/luan.h b/include/configs/luan.h
index 0335a00..0350e91 100644
--- a/include/configs/luan.h
+++ b/include/configs/luan.h
@@ -145,6 +145,13 @@
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
+#define CFG_I2C_MULTI_EEPROMS
+#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#define CFG_EEPROM_PAGE_WRITE_BITS 3
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+
#define CONFIG_PREBOOT "echo;" \
"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
"echo"
@@ -215,6 +222,7 @@
CFG_CMD_DHCP | \
CFG_CMD_DIAG | \
CFG_CMD_ELF | \
+ CFG_CMD_EEPROM | \
CFG_CMD_I2C | \
CFG_CMD_IRQ | \
CFG_CMD_MII | \
@@ -253,6 +261,12 @@
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
diff --git a/include/configs/mcc200.h b/include/configs/mcc200.h
index ce33b85..563f797 100644
--- a/include/configs/mcc200.h
+++ b/include/configs/mcc200.h
@@ -51,15 +51,20 @@
* To select console on the one of 8 external UARTs,
* define CONFIG_QUART_CONSOLE as 1, 2, 3, or 4 for the first Quad UART,
* or as 5, 6, 7, or 8 for the second Quad UART.
+ * COM11, COM12, COM13, COM14 are located on the second Quad UART.
*
* CONFIG_PSC_CONSOLE must be undefined in this case.
*/
-/* #define CONFIG_QUART_CONSOLE 1 */ /* console is on UART1 of QUART1 */
+#ifdef CONFIG_CONSOLE_COM12
+#define CONFIG_QUART_CONSOLE 6 /* console is on UARTF of QUART2 */
+#else
+#define CONFIG_QUART_CONSOLE 8 /* console is on UARTH of QUART2 */
+#endif
/*
* To select console on PSC1, define CONFIG_PSC_CONSOLE as 1
* and undefine CONFIG_QUART_CONSOLE.
*/
-#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
+/*#define CONFIG_PSC_CONSOLE 1 */ /* console is on PSC1 */
#if defined(CONFIG_QUART_CONSOLE) && defined(CONFIG_PSC_CONSOLE)
#error "Select only one console device!"
#endif
diff --git a/include/configs/ocotea.h b/include/configs/ocotea.h
index a13d6a8..89e9164 100644
--- a/include/configs/ocotea.h
+++ b/include/configs/ocotea.h
@@ -158,7 +158,13 @@
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+
+#define CFG_I2C_MULTI_EEPROMS
+#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#define CFG_EEPROM_PAGE_WRITE_BITS 3
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
#define CONFIG_PREBOOT "echo;" \
"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
@@ -219,6 +225,9 @@
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_PHY_RESET_DELAY 1000
+#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
+
+#define CONFIG_NETCONSOLE /* include NetConsole support */
#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
CFG_CMD_ASKENV | \
@@ -226,6 +235,7 @@
CFG_CMD_DHCP | \
CFG_CMD_DIAG | \
CFG_CMD_ELF | \
+ CFG_CMD_EEPROM | \
CFG_CMD_I2C | \
CFG_CMD_IRQ | \
CFG_CMD_MII | \
@@ -264,15 +274,12 @@
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
diff --git a/include/configs/walnut.h b/include/configs/walnut.h
index 1171ee5..28abd6e 100644
--- a/include/configs/walnut.h
+++ b/include/configs/walnut.h
@@ -90,6 +90,11 @@
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 1 /* PHY address */
+#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
+
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+#define CONFIG_NET_MULTI /* needed for NetConsole */
+
#define CONFIG_RTC_DS174x 1 /* use DS1743 RTC in Walnut */
#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
@@ -97,6 +102,7 @@
CFG_CMD_DATE | \
CFG_CMD_DHCP | \
CFG_CMD_DIAG | \
+ CFG_CMD_EEPROM | \
CFG_CMD_ELF | \
CFG_CMD_I2C | \
CFG_CMD_IRQ | \
@@ -156,16 +162,12 @@
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-#define CONFIG_NET_MULTI /* needed for NetConsole */
-
/*-----------------------------------------------------------------------
* I2C stuff
*-----------------------------------------------------------------------
@@ -175,6 +177,13 @@
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
+#define CFG_I2C_MULTI_EEPROMS
+#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#define CFG_EEPROM_PAGE_WRITE_BITS 3
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
diff --git a/include/configs/yellowstone.h b/include/configs/yellowstone.h
index 7d55566..cf42b66 100644
--- a/include/configs/yellowstone.h
+++ b/include/configs/yellowstone.h
@@ -229,6 +229,7 @@
CFG_CMD_DHCP | \
CFG_CMD_DIAG | \
CFG_CMD_ELF | \
+ CFG_CMD_EEPROM | \
CFG_CMD_I2C | \
CFG_CMD_IRQ | \
CFG_CMD_MII | \
@@ -265,6 +266,12 @@
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
diff --git a/include/configs/yosemite.h b/include/configs/yosemite.h
index a81cf34..86a85b8 100644
--- a/include/configs/yosemite.h
+++ b/include/configs/yosemite.h
@@ -231,6 +231,7 @@
CFG_CMD_DHCP | \
CFG_CMD_DIAG | \
CFG_CMD_ELF | \
+ CFG_CMD_EEPROM | \
CFG_CMD_I2C | \
CFG_CMD_IRQ | \
CFG_CMD_MII | \
@@ -272,6 +273,12 @@
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
diff --git a/include/configs/yucca.h b/include/configs/yucca.h
index 0e58e7e..a6532b5 100644
--- a/include/configs/yucca.h
+++ b/include/configs/yucca.h
@@ -31,9 +31,6 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-#define DEBUG
-#undef DEBUG
-
/*-----------------------------------------------------------------------
* High Level Configuration Options
*----------------------------------------------------------------------*/
@@ -63,17 +60,20 @@
#define CFG_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */
#define CFG_ISRAM_BASE 0x90000000 /* internal SRAM */
-#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */
-#define CFG_PCI_MEMBASE1 0x90000000 /* mapped pci memory */
-#define CFG_PCI_MEMBASE2 0xa0000000 /* mapped pci memory */
-#define CFG_PCI_MEMBASE3 0xb0000000 /* mapped pci memory */
-
+#define CFG_PCI_MEMBASE 0x80000000 /* mapped PCI memory */
#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */
-#define CFG_PCI_TARGBASE 0x80000000 /*PCIaddr mapped to CFG_PCI_MEMBASE*/
+#define CFG_PCI_TARGBASE CFG_PCI_MEMBASE
-/* #define CFG_PCI_BASE_IO 0xB8000000 */ /* internal PCI I-O */
-/* #define CFG_PCI_BASE_REGS 0xBEC00000 */ /* internal PCI regs */
-/* #define CFG_PCI_BASE_CYCLE 0xBED00000 */ /* internal PCI regs */
+#define CFG_PCIE_MEMBASE 0xb0000000 /* mapped PCIe memory */
+#define CFG_PCIE_MEMSIZE 0x01000000
+#define CFG_PCIE_BASE 0xe0000000 /* PCIe UTL regs */
+
+#define CFG_PCIE0_CFGBASE 0xc0000000
+#define CFG_PCIE0_XCFGBASE 0xc0000400
+#define CFG_PCIE1_CFGBASE 0xc0001000
+#define CFG_PCIE1_XCFGBASE 0xc0001400
+#define CFG_PCIE2_CFGBASE 0xc0002000
+#define CFG_PCIE2_XCFGBASE 0xc0002400
/* System RAM mapped to PCI space */
#define CONFIG_PCI_SYS_MEM_BUS CFG_SDRAM_BASE
@@ -220,6 +220,9 @@
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+#define CONFIG_NET_MULTI /* needed for NetConsole */
+
#undef CONFIG_WATCHDOG /* watchdog disabled */
/*
@@ -245,6 +248,12 @@
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+
/*-----------------------------------------------------------------------
* FLASH related
*----------------------------------------------------------------------*/
@@ -292,6 +301,7 @@
*/
/* Support for Intel 82557/82559/82559ER chips. */
#define CONFIG_EEPRO100
+
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
@@ -506,8 +516,8 @@
#define FPGA_REG1C_PE1_WAKE 0x0040
#define FPGA_REG1C_PE2_WAKE 0x0020
#define FPGA_REG1C_PE0_PERST 0x0010
-#define FPGA_REG1C_PE1_PERST 0x0080
-#define FPGA_REG1C_PE2_PERST 0x0040
+#define FPGA_REG1C_PE1_PERST 0x0008
+#define FPGA_REG1C_PE2_PERST 0x0004
/*----------------------------------------------------------------------------+
| Defines
diff --git a/include/fat.h b/include/fat.h
index 0645458..92638d5 100644
--- a/include/fat.h
+++ b/include/fat.h
@@ -175,15 +175,19 @@
__u8 name11_12[4]; /* Last 2 characters in name */
} dir_slot;
-/* Private filesystem parameters */
+/* Private filesystem parameters
+ *
+ * Note: FAT buffer has to be 32 bit aligned
+ * (see FAT32 accesses)
+ */
typedef struct {
+ __u8 fatbuf[FATBUFSIZE]; /* Current FAT buffer */
int fatsize; /* Size of FAT in bits */
__u16 fatlength; /* Length of FAT in sectors */
__u16 fat_sect; /* Starting sector of the FAT */
__u16 rootdir_sect; /* Start sector of root directory */
__u16 clust_size; /* Size of clusters in sectors */
short data_begin; /* The sector of the first cluster, can be negative */
- __u8 fatbuf[FATBUFSIZE]; /* Current FAT buffer */
int fatbufnum; /* Used by get_fatent, init to -1 */
} fsdata;
diff --git a/include/mpc5xxx.h b/include/mpc5xxx.h
index 50a6ac1..daa4d5f 100644
--- a/include/mpc5xxx.h
+++ b/include/mpc5xxx.h
@@ -235,20 +235,30 @@
/* General Purpose Timers registers */
#define MPC5XXX_GPT0_ENABLE (MPC5XXX_GPT + 0x0)
#define MPC5XXX_GPT0_COUNTER (MPC5XXX_GPT + 0x4)
+#define MPC5XXX_GPT0_STATUS (MPC5XXX_GPT + 0x0C)
#define MPC5XXX_GPT1_ENABLE (MPC5XXX_GPT + 0x10)
#define MPC5XXX_GPT1_COUNTER (MPC5XXX_GPT + 0x14)
+#define MPC5XXX_GPT1_STATUS (MPC5XXX_GPT + 0x1C)
#define MPC5XXX_GPT2_ENABLE (MPC5XXX_GPT + 0x20)
#define MPC5XXX_GPT2_COUNTER (MPC5XXX_GPT + 0x24)
+#define MPC5XXX_GPT2_STATUS (MPC5XXX_GPT + 0x2C)
#define MPC5XXX_GPT3_ENABLE (MPC5XXX_GPT + 0x30)
#define MPC5XXX_GPT3_COUNTER (MPC5XXX_GPT + 0x34)
+#define MPC5XXX_GPT3_STATUS (MPC5XXX_GPT + 0x3C)
#define MPC5XXX_GPT4_ENABLE (MPC5XXX_GPT + 0x40)
#define MPC5XXX_GPT4_COUNTER (MPC5XXX_GPT + 0x44)
+#define MPC5XXX_GPT4_STATUS (MPC5XXX_GPT + 0x4C)
#define MPC5XXX_GPT5_ENABLE (MPC5XXX_GPT + 0x50)
+#define MPC5XXX_GPT5_STATUS (MPC5XXX_GPT + 0x5C)
#define MPC5XXX_GPT5_COUNTER (MPC5XXX_GPT + 0x54)
#define MPC5XXX_GPT6_ENABLE (MPC5XXX_GPT + 0x60)
#define MPC5XXX_GPT6_COUNTER (MPC5XXX_GPT + 0x64)
+#define MPC5XXX_GPT6_STATUS (MPC5XXX_GPT + 0x6C)
#define MPC5XXX_GPT7_ENABLE (MPC5XXX_GPT + 0x70)
#define MPC5XXX_GPT7_COUNTER (MPC5XXX_GPT + 0x74)
+#define MPC5XXX_GPT7_STATUS (MPC5XXX_GPT + 0x7C)
+
+#define MPC5XXX_GPT_GPIO_PIN(status) ((0x00000100 & (status)) >> 8)
#define MPC5XXX_GPT7_PWMCFG (MPC5XXX_GPT + 0x78)
diff --git a/net/tftp.c b/net/tftp.c
index eca21d2..f3a5471 100644
--- a/net/tftp.c
+++ b/net/tftp.c
@@ -225,7 +225,7 @@
if (TftpBlock == 0) {
TftpBlockWrap++;
TftpBlockWrapOffset += TFTP_BLOCK_SIZE * TFTP_SEQUENCE_SIZE;
- printf ("\n\t %lu MB reveived\n\t ", TftpBlockWrapOffset>>20);
+ printf ("\n\t %lu MB received\n\t ", TftpBlockWrapOffset>>20);
} else {
if (((TftpBlock - 1) % 10) == 0) {
putc ('#');