Patch by Kyle Harris, 20 May 2003:
In preparation for an ixp port, rename cpu/xscale and arch-xscale
into cpu/pxa and arch-pxa.
diff --git a/include/asm-arm/arch-xscale/bitfield.h b/include/asm-arm/arch-pxa/bitfield.h
similarity index 100%
rename from include/asm-arm/arch-xscale/bitfield.h
rename to include/asm-arm/arch-pxa/bitfield.h
diff --git a/include/asm-arm/arch-xscale/hardware.h b/include/asm-arm/arch-pxa/hardware.h
similarity index 100%
rename from include/asm-arm/arch-xscale/hardware.h
rename to include/asm-arm/arch-pxa/hardware.h
diff --git a/include/asm-arm/arch-pxa/pxa-regs.h b/include/asm-arm/arch-pxa/pxa-regs.h
index dda2465..208c110 100644
--- a/include/asm-arm/arch-pxa/pxa-regs.h
+++ b/include/asm-arm/arch-pxa/pxa-regs.h
@@ -8,10 +8,16 @@
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
+ *
+ * - 2003/01/20: Robert Schwebel <r.schwebel@pengutronix.de
+ * Original file taken from linux-2.4.19-rmk4-pxa1. Added some definitions.
+ * Added include for hardware.h (for __REG definition)
*/
+#ifndef _PXA_REGS_H_
+#define _PXA_REGS_H_
-#ifndef PXA_REGS_H
-#define PXA_REGS_H 1
+#include "bitfield.h"
+#include "hardware.h"
/* FIXME hack so that SA-1111.h will work [cb] */
@@ -24,13 +30,6 @@
typedef void (*ExcpHndlr) (void) ;
#endif
-#ifndef __ASSEMBLY__
-#define io_p2v(PhAdd) (PhAdd)
-#define __REG(x) (*((volatile u32 *)io_p2v(x)))
-#else
-#define __REG(x) (x)
-#endif
-
/*
* PXA Chip selects
*/
@@ -416,7 +415,6 @@
IrSR_RCVEIR_UART_MODE | \
IrSR_XMITIR_IR_MODE)
-
/*
* I2C registers
*/
@@ -444,6 +442,7 @@
#define ICR_ALDIE 0x1000 /* enable arbitration interrupt */
#define ICR_SADIE 0x2000 /* slave address detected int enable */
#define ICR_UR 0x4000 /* unit reset */
+#define ICR_FM 0x8000 /* Fast Mode */
/* ----- Status register bits ----------------------------------------- */
@@ -459,7 +458,6 @@
#define ISR_SAD 0x200 /* slave address detected */
#define ISR_BED 0x400 /* bus error no ACK/NAK */
-
/*
* Serial Audio Controller
*/
@@ -558,24 +556,92 @@
/*
* USB Device Controller
*/
+#define UDC_RES1 __REG(0x40600004) /* UDC Undocumented - Reserved1 */
+#define UDC_RES2 __REG(0x40600008) /* UDC Undocumented - Reserved2 */
+#define UDC_RES3 __REG(0x4060000C) /* UDC Undocumented - Reserved3 */
#define UDCCR __REG(0x40600000) /* UDC Control Register */
+#define UDCCR_UDE (1 << 0) /* UDC enable */
+#define UDCCR_UDA (1 << 1) /* UDC active */
+#define UDCCR_RSM (1 << 2) /* Device resume */
+#define UDCCR_RESIR (1 << 3) /* Resume interrupt request */
+#define UDCCR_SUSIR (1 << 4) /* Suspend interrupt request */
+#define UDCCR_SRM (1 << 5) /* Suspend/resume interrupt mask */
+#define UDCCR_RSTIR (1 << 6) /* Reset interrupt request */
+#define UDCCR_REM (1 << 7) /* Reset interrupt mask */
+
#define UDCCS0 __REG(0x40600010) /* UDC Endpoint 0 Control/Status Register */
+#define UDCCS0_OPR (1 << 0) /* OUT packet ready */
+#define UDCCS0_IPR (1 << 1) /* IN packet ready */
+#define UDCCS0_FTF (1 << 2) /* Flush Tx FIFO */
+#define UDCCS0_DRWF (1 << 3) /* Device remote wakeup feature */
+#define UDCCS0_SST (1 << 4) /* Sent stall */
+#define UDCCS0_FST (1 << 5) /* Force stall */
+#define UDCCS0_RNE (1 << 6) /* Receive FIFO no empty */
+#define UDCCS0_SA (1 << 7) /* Setup active */
+
+/* Bulk IN - Endpoint 1,6,11 */
#define UDCCS1 __REG(0x40600014) /* UDC Endpoint 1 (IN) Control/Status Register */
-#define UDCCS2 __REG(0x40600018) /* UDC Endpoint 2 (OUT) Control/Status Register */
-#define UDCCS3 __REG(0x4060001C) /* UDC Endpoint 3 (IN) Control/Status Register */
-#define UDCCS4 __REG(0x40600020) /* UDC Endpoint 4 (OUT) Control/Status Register */
-#define UDCCS5 __REG(0x40600024) /* UDC Endpoint 5 (Interrupt) Control/Status Register */
#define UDCCS6 __REG(0x40600028) /* UDC Endpoint 6 (IN) Control/Status Register */
-#define UDCCS7 __REG(0x4060002C) /* UDC Endpoint 7 (OUT) Control/Status Register */
-#define UDCCS8 __REG(0x40600030) /* UDC Endpoint 8 (IN) Control/Status Register */
-#define UDCCS9 __REG(0x40600034) /* UDC Endpoint 9 (OUT) Control/Status Register */
-#define UDCCS10 __REG(0x40600038) /* UDC Endpoint 10 (Interrupt) Control/Status Register */
#define UDCCS11 __REG(0x4060003C) /* UDC Endpoint 11 (IN) Control/Status Register */
+
+#define UDCCS_BI_TFS (1 << 0) /* Transmit FIFO service */
+#define UDCCS_BI_TPC (1 << 1) /* Transmit packet complete */
+#define UDCCS_BI_FTF (1 << 2) /* Flush Tx FIFO */
+#define UDCCS_BI_TUR (1 << 3) /* Transmit FIFO underrun */
+#define UDCCS_BI_SST (1 << 4) /* Sent stall */
+#define UDCCS_BI_FST (1 << 5) /* Force stall */
+#define UDCCS_BI_TSP (1 << 7) /* Transmit short packet */
+
+/* Bulk OUT - Endpoint 2,7,12 */
+#define UDCCS2 __REG(0x40600018) /* UDC Endpoint 2 (OUT) Control/Status Register */
+#define UDCCS7 __REG(0x4060002C) /* UDC Endpoint 7 (OUT) Control/Status Register */
#define UDCCS12 __REG(0x40600040) /* UDC Endpoint 12 (OUT) Control/Status Register */
+
+#define UDCCS_BO_RFS (1 << 0) /* Receive FIFO service */
+#define UDCCS_BO_RPC (1 << 1) /* Receive packet complete */
+#define UDCCS_BO_DME (1 << 3) /* DMA enable */
+#define UDCCS_BO_SST (1 << 4) /* Sent stall */
+#define UDCCS_BO_FST (1 << 5) /* Force stall */
+#define UDCCS_BO_RNE (1 << 6) /* Receive FIFO not empty */
+#define UDCCS_BO_RSP (1 << 7) /* Receive short packet */
+
+/* Isochronous IN - Endpoint 3,8,13 */
+#define UDCCS3 __REG(0x4060001C) /* UDC Endpoint 3 (IN) Control/Status Register */
+#define UDCCS8 __REG(0x40600030) /* UDC Endpoint 8 (IN) Control/Status Register */
#define UDCCS13 __REG(0x40600044) /* UDC Endpoint 13 (IN) Control/Status Register */
+
+#define UDCCS_II_TFS (1 << 0) /* Transmit FIFO service */
+#define UDCCS_II_TPC (1 << 1) /* Transmit packet complete */
+#define UDCCS_II_FTF (1 << 2) /* Flush Tx FIFO */
+#define UDCCS_II_TUR (1 << 3) /* Transmit FIFO underrun */
+#define UDCCS_II_TSP (1 << 7) /* Transmit short packet */
+
+/* Isochronous OUT - Endpoint 4,9,14 */
+#define UDCCS4 __REG(0x40600020) /* UDC Endpoint 4 (OUT) Control/Status Register */
+#define UDCCS9 __REG(0x40600034) /* UDC Endpoint 9 (OUT) Control/Status Register */
#define UDCCS14 __REG(0x40600048) /* UDC Endpoint 14 (OUT) Control/Status Register */
+
+#define UDCCS_IO_RFS (1 << 0) /* Receive FIFO service */
+#define UDCCS_IO_RPC (1 << 1) /* Receive packet complete */
+#define UDCCS_IO_ROF (1 << 3) /* Receive overflow */
+#define UDCCS_IO_DME (1 << 3) /* DMA enable */
+#define UDCCS_IO_RNE (1 << 6) /* Receive FIFO not empty */
+#define UDCCS_IO_RSP (1 << 7) /* Receive short packet */
+
+/* Interrupt IN - Endpoint 5,10,15 */
+#define UDCCS5 __REG(0x40600024) /* UDC Endpoint 5 (Interrupt) Control/Status Register */
+#define UDCCS10 __REG(0x40600038) /* UDC Endpoint 10 (Interrupt) Control/Status Register */
#define UDCCS15 __REG(0x4060004C) /* UDC Endpoint 15 (Interrupt) Control/Status Register */
+
+#define UDCCS_INT_TFS (1 << 0) /* Transmit FIFO service */
+#define UDCCS_INT_TPC (1 << 1) /* Transmit packet complete */
+#define UDCCS_INT_FTF (1 << 2) /* Flush Tx FIFO */
+#define UDCCS_INT_TUR (1 << 3) /* Transmit FIFO underrun */
+#define UDCCS_INT_SST (1 << 4) /* Sent stall */
+#define UDCCS_INT_FST (1 << 5) /* Force stall */
+#define UDCCS_INT_TSP (1 << 7) /* Transmit short packet */
+
#define UFNRH __REG(0x40600060) /* UDC Frame Number Register High */
#define UFNRL __REG(0x40600064) /* UDC Frame Number Register Low */
#define UBCR2 __REG(0x40600068) /* UDC Byte Count Reg 2 */
@@ -600,11 +666,51 @@
#define UDDR13 __REG(0x40600C00) /* UDC Endpoint 13 Data Register */
#define UDDR14 __REG(0x40600E00) /* UDC Endpoint 14 Data Register */
#define UDDR15 __REG(0x406000E0) /* UDC Endpoint 15 Data Register */
+
#define UICR0 __REG(0x40600050) /* UDC Interrupt Control Register 0 */
+
+#define UICR0_IM0 (1 << 0) /* Interrupt mask ep 0 */
+#define UICR0_IM1 (1 << 1) /* Interrupt mask ep 1 */
+#define UICR0_IM2 (1 << 2) /* Interrupt mask ep 2 */
+#define UICR0_IM3 (1 << 3) /* Interrupt mask ep 3 */
+#define UICR0_IM4 (1 << 4) /* Interrupt mask ep 4 */
+#define UICR0_IM5 (1 << 5) /* Interrupt mask ep 5 */
+#define UICR0_IM6 (1 << 6) /* Interrupt mask ep 6 */
+#define UICR0_IM7 (1 << 7) /* Interrupt mask ep 7 */
+
#define UICR1 __REG(0x40600054) /* UDC Interrupt Control Register 1 */
+
+#define UICR1_IM8 (1 << 0) /* Interrupt mask ep 8 */
+#define UICR1_IM9 (1 << 1) /* Interrupt mask ep 9 */
+#define UICR1_IM10 (1 << 2) /* Interrupt mask ep 10 */
+#define UICR1_IM11 (1 << 3) /* Interrupt mask ep 11 */
+#define UICR1_IM12 (1 << 4) /* Interrupt mask ep 12 */
+#define UICR1_IM13 (1 << 5) /* Interrupt mask ep 13 */
+#define UICR1_IM14 (1 << 6) /* Interrupt mask ep 14 */
+#define UICR1_IM15 (1 << 7) /* Interrupt mask ep 15 */
+
#define USIR0 __REG(0x40600058) /* UDC Status Interrupt Register 0 */
+
+#define USIR0_IR0 (1 << 0) /* Interrup request ep 0 */
+#define USIR0_IR1 (1 << 1) /* Interrup request ep 1 */
+#define USIR0_IR2 (1 << 2) /* Interrup request ep 2 */
+#define USIR0_IR3 (1 << 3) /* Interrup request ep 3 */
+#define USIR0_IR4 (1 << 4) /* Interrup request ep 4 */
+#define USIR0_IR5 (1 << 5) /* Interrup request ep 5 */
+#define USIR0_IR6 (1 << 6) /* Interrup request ep 6 */
+#define USIR0_IR7 (1 << 7) /* Interrup request ep 7 */
+
#define USIR1 __REG(0x4060005C) /* UDC Status Interrupt Register 1 */
+#define USIR1_IR8 (1 << 0) /* Interrup request ep 8 */
+#define USIR1_IR9 (1 << 1) /* Interrup request ep 9 */
+#define USIR1_IR10 (1 << 2) /* Interrup request ep 10 */
+#define USIR1_IR11 (1 << 3) /* Interrup request ep 11 */
+#define USIR1_IR12 (1 << 4) /* Interrup request ep 12 */
+#define USIR1_IR13 (1 << 5) /* Interrup request ep 13 */
+#define USIR1_IR14 (1 << 6) /* Interrup request ep 14 */
+#define USIR1_IR15 (1 << 7) /* Interrup request ep 15 */
+
/*
* Fast Infrared Communication Port
@@ -951,6 +1057,22 @@
#define PGSR2 __REG(0x40F00028) /* Power Manager GPIO Sleep State Register for GP[84-64] */
#define RCSR __REG(0x40F00030) /* Reset Controller Status Register */
+#define PSSR_RDH (1 << 5) /* Read Disable Hold */
+#define PSSR_PH (1 << 4) /* Peripheral Control Hold */
+#define PSSR_VFS (1 << 2) /* VDD Fault Status */
+#define PSSR_BFS (1 << 1) /* Battery Fault Status */
+#define PSSR_SSS (1 << 0) /* Software Sleep Status */
+
+#define PCFR_DS (1 << 3) /* Deep Sleep Mode */
+#define PCFR_FS (1 << 2) /* Float Static Chip Selects */
+#define PCFR_FP (1 << 1) /* Float PCMCIA controls */
+#define PCFR_OPDE (1 << 0) /* 3.6864 MHz oscillator power-down enable */
+
+#define RCSR_GPR (1 << 3) /* GPIO Reset */
+#define RCSR_SMR (1 << 2) /* Sleep Mode */
+#define RCSR_WDR (1 << 1) /* Watchdog Reset */
+#define RCSR_HWR (1 << 0) /* Hardware Reset */
+
/*
* SSP Serial Port Registers
@@ -1074,19 +1196,105 @@
#define LCCR0_BM (1 << 20) /* Branch mask */
#define LCCR0_OUM (1 << 21) /* Output FIFO underrun mask */
+#define LCCR1_PPL Fld (10, 0) /* Pixels Per Line - 1 */
+#define LCCR1_DisWdth(Pixel) /* Display Width [1..800 pix.] */ \
+ (((Pixel) - 1) << FShft (LCCR1_PPL))
+
+#define LCCR1_HSW Fld (6, 10) /* Horizontal Synchronization */
+#define LCCR1_HorSnchWdth(Tpix) /* Horizontal Synchronization */ \
+ /* pulse Width [1..64 Tpix] */ \
+ (((Tpix) - 1) << FShft (LCCR1_HSW))
+
+#define LCCR1_ELW Fld (8, 16) /* End-of-Line pixel clock Wait */
+ /* count - 1 [Tpix] */
+#define LCCR1_EndLnDel(Tpix) /* End-of-Line Delay */ \
+ /* [1..256 Tpix] */ \
+ (((Tpix) - 1) << FShft (LCCR1_ELW))
+
+#define LCCR1_BLW Fld (8, 24) /* Beginning-of-Line pixel clock */
+ /* Wait count - 1 [Tpix] */
+#define LCCR1_BegLnDel(Tpix) /* Beginning-of-Line Delay */ \
+ /* [1..256 Tpix] */ \
+ (((Tpix) - 1) << FShft (LCCR1_BLW))
+
+
+#define LCCR2_LPP Fld (10, 0) /* Line Per Panel - 1 */
+#define LCCR2_DisHght(Line) /* Display Height [1..1024 lines] */ \
+ (((Line) - 1) << FShft (LCCR2_LPP))
+
+#define LCCR2_VSW Fld (6, 10) /* Vertical Synchronization pulse */
+ /* Width - 1 [Tln] (L_FCLK) */
+#define LCCR2_VrtSnchWdth(Tln) /* Vertical Synchronization pulse */ \
+ /* Width [1..64 Tln] */ \
+ (((Tln) - 1) << FShft (LCCR2_VSW))
+
+#define LCCR2_EFW Fld (8, 16) /* End-of-Frame line clock Wait */
+ /* count [Tln] */
+#define LCCR2_EndFrmDel(Tln) /* End-of-Frame Delay */ \
+ /* [0..255 Tln] */ \
+ ((Tln) << FShft (LCCR2_EFW))
+
+#define LCCR2_BFW Fld (8, 24) /* Beginning-of-Frame line clock */
+ /* Wait count [Tln] */
+#define LCCR2_BegFrmDel(Tln) /* Beginning-of-Frame Delay */ \
+ /* [0..255 Tln] */ \
+ ((Tln) << FShft (LCCR2_BFW))
+
+#if 0
#define LCCR3_PCD (0xff) /* Pixel clock divisor */
#define LCCR3_ACB (0xff << 8) /* AC Bias pin frequency */
#define LCCR3_ACB_S 8
+#endif
+
#define LCCR3_API (0xf << 16) /* AC Bias pin trasitions per interrupt */
#define LCCR3_API_S 16
#define LCCR3_VSP (1 << 20) /* vertical sync polarity */
#define LCCR3_HSP (1 << 21) /* horizontal sync polarity */
#define LCCR3_PCP (1 << 22) /* pixel clock polarity */
#define LCCR3_OEP (1 << 23) /* output enable polarity */
+#if 0
#define LCCR3_BPP (7 << 24) /* bits per pixel */
#define LCCR3_BPP_S 24
+#endif
#define LCCR3_DPC (1 << 27) /* double pixel clock mode */
+
+#define LCCR3_PCD Fld (8, 0) /* Pixel Clock Divisor */
+#define LCCR3_PixClkDiv(Div) /* Pixel Clock Divisor */ \
+ (((Div) << FShft (LCCR3_PCD)))
+
+
+#define LCCR3_BPP Fld (3, 24) /* Bit Per Pixel */
+#define LCCR3_Bpp(Bpp) /* Bit Per Pixel */ \
+ (((Bpp) << FShft (LCCR3_BPP)))
+
+#define LCCR3_ACB Fld (8, 8) /* AC Bias */
+#define LCCR3_Acb(Acb) /* BAC Bias */ \
+ (((Acb) << FShft (LCCR3_ACB)))
+
+#define LCCR3_HorSnchH (LCCR3_HSP*0) /* Horizontal Synchronization */
+ /* pulse active High */
+#define LCCR3_HorSnchL (LCCR3_HSP*1) /* Horizontal Synchronization */
+
+#define LCCR3_VrtSnchH (LCCR3_VSP*0) /* Vertical Synchronization pulse */
+ /* active High */
+#define LCCR3_VrtSnchL (LCCR3_VSP*1) /* Vertical Synchronization pulse */
+ /* active Low */
+
+#define LCSR_LDD (1 << 0) /* LCD Disable Done */
+#define LCSR_SOF (1 << 1) /* Start of frame */
+#define LCSR_BER (1 << 2) /* Bus error */
+#define LCSR_ABC (1 << 3) /* AC Bias count */
+#define LCSR_IUL (1 << 4) /* input FIFO underrun Lower panel */
+#define LCSR_IUU (1 << 5) /* input FIFO underrun Upper panel */
+#define LCSR_OU (1 << 6) /* output FIFO underrun */
+#define LCSR_QD (1 << 7) /* quick disable */
+#define LCSR_EOF (1 << 8) /* end of frame */
+#define LCSR_BS (1 << 9) /* branch status */
+#define LCSR_SINT (1 << 10) /* subsequent interrupt */
+
+#define LDCMD_PAL (1 << 26) /* instructs DMA to load palette buffer */
+
#define LCSR_LDD (1 << 0) /* LCD Disable Done */
#define LCSR_SOF (1 << 1) /* Start of frame */
#define LCSR_BER (1 << 2) /* Bus error */
@@ -1105,45 +1313,7 @@
* Memory controller
*/
-#define MEMC_BASE __REG(0x48000000) /* Base of Memoriy Controller */
-#define MDCNFG __REG(0x48000000) /* SDRAM Configuration Register 0 */
-#define MDREFR __REG(0x48000004) /* SDRAM Refresh Control Register */
-#define MSC0 __REG(0x48000008) /* Static Memory Control Register 0 */
-#define MSC1 __REG(0x4800000C) /* Static Memory Control Register 1 */
-#define MSC2 __REG(0x48000010) /* Static Memory Control Register 2 */
-#define MECR __REG(0x48000014) /* Expansion Memory (PCMCIA/Compact Flash) Bus Configuration */
-#define SXLCR __REG(0x48000018) /* LCR value to be written to SDRAM-Timing Synchronous Flash */
-#define SXCNFG __REG(0x4800001C) /* Synchronous Static Memory Control Register */
-#define SXMRS __REG(0x48000024) /* MRS value to be written to Synchronous Flash or SMROM */
-#define MCMEM0 __REG(0x48000028) /* Card interface Common Memory Space Socket 0 Timing */
-#define MCMEM1 __REG(0x4800002C) /* Card interface Common Memory Space Socket 1 Timing */
-#define MCATT0 __REG(0x48000030) /* Card interface Attribute Space Socket 0 Timing Configuration */
-#define MCATT1 __REG(0x48000034) /* Card interface Attribute Space Socket 1 Timing Configuration */
-#define MCIO0 __REG(0x48000038) /* Card interface I/O Space Socket 0 Timing Configuration */
-#define MCIO1 __REG(0x4800003C) /* Card interface I/O Space Socket 1 Timing Configuration */
-#define MDMRS __REG(0x48000040) /* MRS value to be written to SDRAM */
-#define BOOT_DEF __REG(0x48000044) /* Read-Only Boot-Time Register. Contains BOOT_SEL and PKG_SEL */
-
-#define MDCNFG_DE0 0x00000001
-#define MDCNFG_DE1 0x00000002
-#define MDCNFG_DE2 0x00010000
-#define MDCNFG_DE3 0x00020000
-#define MDCNFG_DWID0 0x00000004
-
-#define MDREFR_E0PIN 0x00001000
-#define MDREFR_K0RUN 0x00002000
-#define MDREFR_K0DB2 0x00004000
-#define MDREFR_E1PIN 0x00008000
-#define MDREFR_K1RUN 0x00010000
-#define MDREFR_K1DB2 0x00020000
-#define MDREFR_K2RUN 0x00040000
-#define MDREFR_K2DB2 0x00080000
-#define MDREFR_APD 0x00100000
-#define MDREFR_SLFRSH 0x00400000
-#define MDREFR_K0FREE 0x00800000
-#define MDREFR_K1FREE 0x01000000
-#define MDREFR_K2FREE 0x02000000
-
+#define MEMC_BASE __REG(0x48000000) /* Base of Memory Controller */
#define MDCNFG_OFFSET 0x0
#define MDREFR_OFFSET 0x4
#define MSC0_OFFSET 0x8
@@ -1162,6 +1332,43 @@
#define MCIO1_OFFSET 0x3C
#define MDMRS_OFFSET 0x40
-#endif /* PXA_REGS_H */
+#define MDCNFG __REG(0x48000000) /* SDRAM Configuration Register 0 */
+#define MDCNFG_DE0 0x00000001
+#define MDCNFG_DE1 0x00000002
+#define MDCNFG_DE2 0x00010000
+#define MDCNFG_DE3 0x00020000
+#define MDCNFG_DWID0 0x00000004
+
+#define MDREFR __REG(0x48000004) /* SDRAM Refresh Control Register */
+#define MSC0 __REG(0x48000008) /* Static Memory Control Register 0 */
+#define MSC1 __REG(0x4800000C) /* Static Memory Control Register 1 */
+#define MSC2 __REG(0x48000010) /* Static Memory Control Register 2 */
+#define MECR __REG(0x48000014) /* Expansion Memory (PCMCIA/Compact Flash) Bus Configuration */
+#define SXLCR __REG(0x48000018) /* LCR value to be written to SDRAM-Timing Synchronous Flash */
+#define SXCNFG __REG(0x4800001C) /* Synchronous Static Memory Control Register */
+#define SXMRS __REG(0x48000024) /* MRS value to be written to Synchronous Flash or SMROM */
+#define MCMEM0 __REG(0x48000028) /* Card interface Common Memory Space Socket 0 Timing */
+#define MCMEM1 __REG(0x4800002C) /* Card interface Common Memory Space Socket 1 Timing */
+#define MCATT0 __REG(0x48000030) /* Card interface Attribute Space Socket 0 Timing Configuration */
+#define MCATT1 __REG(0x48000034) /* Card interface Attribute Space Socket 1 Timing Configuration */
+#define MCIO0 __REG(0x48000038) /* Card interface I/O Space Socket 0 Timing Configuration */
+#define MCIO1 __REG(0x4800003C) /* Card interface I/O Space Socket 1 Timing Configuration */
+#define MDMRS __REG(0x48000040) /* MRS value to be written to SDRAM */
+#define BOOT_DEF __REG(0x48000044) /* Read-Only Boot-Time Register. Contains BOOT_SEL and PKG_SEL */
+
+#define MDREFR_K2FREE (1 << 25) /* SDRAM Free-Running Control */
+#define MDREFR_K1FREE (1 << 24) /* SDRAM Free-Running Control */
+#define MDREFR_K0FREE (1 << 23) /* SDRAM Free-Running Control */
+#define MDREFR_SLFRSH (1 << 22) /* SDRAM Self-Refresh Control/Status */
+#define MDREFR_APD (1 << 20) /* SDRAM/SSRAM Auto-Power-Down Enable */
+#define MDREFR_K2DB2 (1 << 19) /* SDCLK2 Divide by 2 Control/Status */
+#define MDREFR_K2RUN (1 << 18) /* SDCLK2 Run Control/Status */
+#define MDREFR_K1DB2 (1 << 17) /* SDCLK1 Divide by 2 Control/Status */
+#define MDREFR_K1RUN (1 << 16) /* SDCLK1 Run Control/Status */
+#define MDREFR_E1PIN (1 << 15) /* SDCKE1 Level Control/Status */
+#define MDREFR_K0DB2 (1 << 14) /* SDCLK0 Divide by 2 Control/Status */
+#define MDREFR_K0RUN (1 << 13) /* SDCLK0 Run Control/Status */
+#define MDREFR_E0PIN (1 << 12) /* SDCKE0 Level Control/Status */
+#endif
diff --git a/include/asm-arm/arch-xscale/pxa-regs.h b/include/asm-arm/arch-xscale/pxa-regs.h
deleted file mode 100644
index 449ec9f..0000000
--- a/include/asm-arm/arch-xscale/pxa-regs.h
+++ /dev/null
@@ -1,1374 +0,0 @@
-/*
- * linux/include/asm-arm/arch-pxa/pxa-regs.h
- *
- * Author: Nicolas Pitre
- * Created: Jun 15, 2001
- * Copyright: MontaVista Software Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * - 2003/01/20: Robert Schwebel <r.schwebel@pengutronix.de
- * Original file taken from linux-2.4.19-rmk4-pxa1. Added some definitions.
- * Added include for hardware.h (for __REG definition)
- */
-#ifndef _PXA_REGS_H_
-#define _PXA_REGS_H_
-
-#include "bitfield.h"
-#include "hardware.h"
-
-/* FIXME hack so that SA-1111.h will work [cb] */
-
-#ifndef __ASSEMBLY__
-typedef unsigned short Word16 ;
-typedef unsigned int Word32 ;
-typedef Word32 Word ;
-typedef Word Quad [4] ;
-typedef void *Address ;
-typedef void (*ExcpHndlr) (void) ;
-#endif
-
-/*
- * PXA Chip selects
- */
-
-#define PXA_CS0_PHYS 0x00000000
-#define PXA_CS1_PHYS 0x04000000
-#define PXA_CS2_PHYS 0x08000000
-#define PXA_CS3_PHYS 0x0C000000
-#define PXA_CS4_PHYS 0x10000000
-#define PXA_CS5_PHYS 0x14000000
-
-
-/*
- * Personal Computer Memory Card International Association (PCMCIA) sockets
- */
-
-#define PCMCIAPrtSp 0x04000000 /* PCMCIA Partition Space [byte] */
-#define PCMCIASp (4*PCMCIAPrtSp) /* PCMCIA Space [byte] */
-#define PCMCIAIOSp PCMCIAPrtSp /* PCMCIA I/O Space [byte] */
-#define PCMCIAAttrSp PCMCIAPrtSp /* PCMCIA Attribute Space [byte] */
-#define PCMCIAMemSp PCMCIAPrtSp /* PCMCIA Memory Space [byte] */
-
-#define PCMCIA0Sp PCMCIASp /* PCMCIA 0 Space [byte] */
-#define PCMCIA0IOSp PCMCIAIOSp /* PCMCIA 0 I/O Space [byte] */
-#define PCMCIA0AttrSp PCMCIAAttrSp /* PCMCIA 0 Attribute Space [byte] */
-#define PCMCIA0MemSp PCMCIAMemSp /* PCMCIA 0 Memory Space [byte] */
-
-#define PCMCIA1Sp PCMCIASp /* PCMCIA 1 Space [byte] */
-#define PCMCIA1IOSp PCMCIAIOSp /* PCMCIA 1 I/O Space [byte] */
-#define PCMCIA1AttrSp PCMCIAAttrSp /* PCMCIA 1 Attribute Space [byte] */
-#define PCMCIA1MemSp PCMCIAMemSp /* PCMCIA 1 Memory Space [byte] */
-
-#define _PCMCIA(Nb) /* PCMCIA [0..1] */ \
- (0x20000000 + (Nb)*PCMCIASp)
-#define _PCMCIAIO(Nb) _PCMCIA (Nb) /* PCMCIA I/O [0..1] */
-#define _PCMCIAAttr(Nb) /* PCMCIA Attribute [0..1] */ \
- (_PCMCIA (Nb) + 2*PCMCIAPrtSp)
-#define _PCMCIAMem(Nb) /* PCMCIA Memory [0..1] */ \
- (_PCMCIA (Nb) + 3*PCMCIAPrtSp)
-
-#define _PCMCIA0 _PCMCIA (0) /* PCMCIA 0 */
-#define _PCMCIA0IO _PCMCIAIO (0) /* PCMCIA 0 I/O */
-#define _PCMCIA0Attr _PCMCIAAttr (0) /* PCMCIA 0 Attribute */
-#define _PCMCIA0Mem _PCMCIAMem (0) /* PCMCIA 0 Memory */
-
-#define _PCMCIA1 _PCMCIA (1) /* PCMCIA 1 */
-#define _PCMCIA1IO _PCMCIAIO (1) /* PCMCIA 1 I/O */
-#define _PCMCIA1Attr _PCMCIAAttr (1) /* PCMCIA 1 Attribute */
-#define _PCMCIA1Mem _PCMCIAMem (1) /* PCMCIA 1 Memory */
-
-
-
-/*
- * DMA Controller
- */
-
-#define DCSR0 __REG(0x40000000) /* DMA Control / Status Register for Channel 0 */
-#define DCSR1 __REG(0x40000004) /* DMA Control / Status Register for Channel 1 */
-#define DCSR2 __REG(0x40000008) /* DMA Control / Status Register for Channel 2 */
-#define DCSR3 __REG(0x4000000c) /* DMA Control / Status Register for Channel 3 */
-#define DCSR4 __REG(0x40000010) /* DMA Control / Status Register for Channel 4 */
-#define DCSR5 __REG(0x40000014) /* DMA Control / Status Register for Channel 5 */
-#define DCSR6 __REG(0x40000018) /* DMA Control / Status Register for Channel 6 */
-#define DCSR7 __REG(0x4000001c) /* DMA Control / Status Register for Channel 7 */
-#define DCSR8 __REG(0x40000020) /* DMA Control / Status Register for Channel 8 */
-#define DCSR9 __REG(0x40000024) /* DMA Control / Status Register for Channel 9 */
-#define DCSR10 __REG(0x40000028) /* DMA Control / Status Register for Channel 10 */
-#define DCSR11 __REG(0x4000002c) /* DMA Control / Status Register for Channel 11 */
-#define DCSR12 __REG(0x40000030) /* DMA Control / Status Register for Channel 12 */
-#define DCSR13 __REG(0x40000034) /* DMA Control / Status Register for Channel 13 */
-#define DCSR14 __REG(0x40000038) /* DMA Control / Status Register for Channel 14 */
-#define DCSR15 __REG(0x4000003c) /* DMA Control / Status Register for Channel 15 */
-
-#define DCSR(x) __REG2(0x40000000, (x) << 2)
-
-#define DCSR_RUN (1 << 31) /* Run Bit (read / write) */
-#define DCSR_NODESC (1 << 30) /* No-Descriptor Fetch (read / write) */
-#define DCSR_STOPIRQEN (1 << 29) /* Stop Interrupt Enable (read / write) */
-#define DCSR_REQPEND (1 << 8) /* Request Pending (read-only) */
-#define DCSR_STOPSTATE (1 << 3) /* Stop State (read-only) */
-#define DCSR_ENDINTR (1 << 2) /* End Interrupt (read / write) */
-#define DCSR_STARTINTR (1 << 1) /* Start Interrupt (read / write) */
-#define DCSR_BUSERR (1 << 0) /* Bus Error Interrupt (read / write) */
-
-#define DINT __REG(0x400000f0) /* DMA Interrupt Register */
-
-#define DRCMR0 __REG(0x40000100) /* Request to Channel Map Register for DREQ 0 */
-#define DRCMR1 __REG(0x40000104) /* Request to Channel Map Register for DREQ 1 */
-#define DRCMR2 __REG(0x40000108) /* Request to Channel Map Register for I2S receive Request */
-#define DRCMR3 __REG(0x4000010c) /* Request to Channel Map Register for I2S transmit Request */
-#define DRCMR4 __REG(0x40000110) /* Request to Channel Map Register for BTUART receive Request */
-#define DRCMR5 __REG(0x40000114) /* Request to Channel Map Register for BTUART transmit Request. */
-#define DRCMR6 __REG(0x40000118) /* Request to Channel Map Register for FFUART receive Request */
-#define DRCMR7 __REG(0x4000011c) /* Request to Channel Map Register for FFUART transmit Request */
-#define DRCMR8 __REG(0x40000120) /* Request to Channel Map Register for AC97 microphone Request */
-#define DRCMR9 __REG(0x40000124) /* Request to Channel Map Register for AC97 modem receive Request */
-#define DRCMR10 __REG(0x40000128) /* Request to Channel Map Register for AC97 modem transmit Request */
-#define DRCMR11 __REG(0x4000012c) /* Request to Channel Map Register for AC97 audio receive Request */
-#define DRCMR12 __REG(0x40000130) /* Request to Channel Map Register for AC97 audio transmit Request */
-#define DRCMR13 __REG(0x40000134) /* Request to Channel Map Register for SSP receive Request */
-#define DRCMR14 __REG(0x40000138) /* Request to Channel Map Register for SSP transmit Request */
-#define DRCMR15 __REG(0x4000013c) /* Reserved */
-#define DRCMR16 __REG(0x40000140) /* Reserved */
-#define DRCMR17 __REG(0x40000144) /* Request to Channel Map Register for ICP receive Request */
-#define DRCMR18 __REG(0x40000148) /* Request to Channel Map Register for ICP transmit Request */
-#define DRCMR19 __REG(0x4000014c) /* Request to Channel Map Register for STUART receive Request */
-#define DRCMR20 __REG(0x40000150) /* Request to Channel Map Register for STUART transmit Request */
-#define DRCMR21 __REG(0x40000154) /* Request to Channel Map Register for MMC receive Request */
-#define DRCMR22 __REG(0x40000158) /* Request to Channel Map Register for MMC transmit Request */
-#define DRCMR23 __REG(0x4000015c) /* Reserved */
-#define DRCMR24 __REG(0x40000160) /* Reserved */
-#define DRCMR25 __REG(0x40000164) /* Request to Channel Map Register for USB endpoint 1 Request */
-#define DRCMR26 __REG(0x40000168) /* Request to Channel Map Register for USB endpoint 2 Request */
-#define DRCMR27 __REG(0x4000016C) /* Request to Channel Map Register for USB endpoint 3 Request */
-#define DRCMR28 __REG(0x40000170) /* Request to Channel Map Register for USB endpoint 4 Request */
-#define DRCMR29 __REG(0x40000174) /* Reserved */
-#define DRCMR30 __REG(0x40000178) /* Request to Channel Map Register for USB endpoint 6 Request */
-#define DRCMR31 __REG(0x4000017C) /* Request to Channel Map Register for USB endpoint 7 Request */
-#define DRCMR32 __REG(0x40000180) /* Request to Channel Map Register for USB endpoint 8 Request */
-#define DRCMR33 __REG(0x40000184) /* Request to Channel Map Register for USB endpoint 9 Request */
-#define DRCMR34 __REG(0x40000188) /* Reserved */
-#define DRCMR35 __REG(0x4000018C) /* Request to Channel Map Register for USB endpoint 11 Request */
-#define DRCMR36 __REG(0x40000190) /* Request to Channel Map Register for USB endpoint 12 Request */
-#define DRCMR37 __REG(0x40000194) /* Request to Channel Map Register for USB endpoint 13 Request */
-#define DRCMR38 __REG(0x40000198) /* Request to Channel Map Register for USB endpoint 14 Request */
-#define DRCMR39 __REG(0x4000019C) /* Reserved */
-
-#define DRCMRRXSADR DRCMR2
-#define DRCMRTXSADR DRCMR3
-#define DRCMRRXBTRBR DRCMR4
-#define DRCMRTXBTTHR DRCMR5
-#define DRCMRRXFFRBR DRCMR6
-#define DRCMRTXFFTHR DRCMR7
-#define DRCMRRXMCDR DRCMR8
-#define DRCMRRXMODR DRCMR9
-#define DRCMRTXMODR DRCMR10
-#define DRCMRRXPCDR DRCMR11
-#define DRCMRTXPCDR DRCMR12
-#define DRCMRRXSSDR DRCMR13
-#define DRCMRTXSSDR DRCMR14
-#define DRCMRRXICDR DRCMR17
-#define DRCMRTXICDR DRCMR18
-#define DRCMRRXSTRBR DRCMR19
-#define DRCMRTXSTTHR DRCMR20
-#define DRCMRRXMMC DRCMR21
-#define DRCMRTXMMC DRCMR22
-
-#define DRCMR_MAPVLD (1 << 7) /* Map Valid (read / write) */
-#define DRCMR_CHLNUM 0x0f /* mask for Channel Number (read / write) */
-
-#define DDADR0 __REG(0x40000200) /* DMA Descriptor Address Register Channel 0 */
-#define DSADR0 __REG(0x40000204) /* DMA Source Address Register Channel 0 */
-#define DTADR0 __REG(0x40000208) /* DMA Target Address Register Channel 0 */
-#define DCMD0 __REG(0x4000020c) /* DMA Command Address Register Channel 0 */
-#define DDADR1 __REG(0x40000210) /* DMA Descriptor Address Register Channel 1 */
-#define DSADR1 __REG(0x40000214) /* DMA Source Address Register Channel 1 */
-#define DTADR1 __REG(0x40000218) /* DMA Target Address Register Channel 1 */
-#define DCMD1 __REG(0x4000021c) /* DMA Command Address Register Channel 1 */
-#define DDADR2 __REG(0x40000220) /* DMA Descriptor Address Register Channel 2 */
-#define DSADR2 __REG(0x40000224) /* DMA Source Address Register Channel 2 */
-#define DTADR2 __REG(0x40000228) /* DMA Target Address Register Channel 2 */
-#define DCMD2 __REG(0x4000022c) /* DMA Command Address Register Channel 2 */
-#define DDADR3 __REG(0x40000230) /* DMA Descriptor Address Register Channel 3 */
-#define DSADR3 __REG(0x40000234) /* DMA Source Address Register Channel 3 */
-#define DTADR3 __REG(0x40000238) /* DMA Target Address Register Channel 3 */
-#define DCMD3 __REG(0x4000023c) /* DMA Command Address Register Channel 3 */
-#define DDADR4 __REG(0x40000240) /* DMA Descriptor Address Register Channel 4 */
-#define DSADR4 __REG(0x40000244) /* DMA Source Address Register Channel 4 */
-#define DTADR4 __REG(0x40000248) /* DMA Target Address Register Channel 4 */
-#define DCMD4 __REG(0x4000024c) /* DMA Command Address Register Channel 4 */
-#define DDADR5 __REG(0x40000250) /* DMA Descriptor Address Register Channel 5 */
-#define DSADR5 __REG(0x40000254) /* DMA Source Address Register Channel 5 */
-#define DTADR5 __REG(0x40000258) /* DMA Target Address Register Channel 5 */
-#define DCMD5 __REG(0x4000025c) /* DMA Command Address Register Channel 5 */
-#define DDADR6 __REG(0x40000260) /* DMA Descriptor Address Register Channel 6 */
-#define DSADR6 __REG(0x40000264) /* DMA Source Address Register Channel 6 */
-#define DTADR6 __REG(0x40000268) /* DMA Target Address Register Channel 6 */
-#define DCMD6 __REG(0x4000026c) /* DMA Command Address Register Channel 6 */
-#define DDADR7 __REG(0x40000270) /* DMA Descriptor Address Register Channel 7 */
-#define DSADR7 __REG(0x40000274) /* DMA Source Address Register Channel 7 */
-#define DTADR7 __REG(0x40000278) /* DMA Target Address Register Channel 7 */
-#define DCMD7 __REG(0x4000027c) /* DMA Command Address Register Channel 7 */
-#define DDADR8 __REG(0x40000280) /* DMA Descriptor Address Register Channel 8 */
-#define DSADR8 __REG(0x40000284) /* DMA Source Address Register Channel 8 */
-#define DTADR8 __REG(0x40000288) /* DMA Target Address Register Channel 8 */
-#define DCMD8 __REG(0x4000028c) /* DMA Command Address Register Channel 8 */
-#define DDADR9 __REG(0x40000290) /* DMA Descriptor Address Register Channel 9 */
-#define DSADR9 __REG(0x40000294) /* DMA Source Address Register Channel 9 */
-#define DTADR9 __REG(0x40000298) /* DMA Target Address Register Channel 9 */
-#define DCMD9 __REG(0x4000029c) /* DMA Command Address Register Channel 9 */
-#define DDADR10 __REG(0x400002a0) /* DMA Descriptor Address Register Channel 10 */
-#define DSADR10 __REG(0x400002a4) /* DMA Source Address Register Channel 10 */
-#define DTADR10 __REG(0x400002a8) /* DMA Target Address Register Channel 10 */
-#define DCMD10 __REG(0x400002ac) /* DMA Command Address Register Channel 10 */
-#define DDADR11 __REG(0x400002b0) /* DMA Descriptor Address Register Channel 11 */
-#define DSADR11 __REG(0x400002b4) /* DMA Source Address Register Channel 11 */
-#define DTADR11 __REG(0x400002b8) /* DMA Target Address Register Channel 11 */
-#define DCMD11 __REG(0x400002bc) /* DMA Command Address Register Channel 11 */
-#define DDADR12 __REG(0x400002c0) /* DMA Descriptor Address Register Channel 12 */
-#define DSADR12 __REG(0x400002c4) /* DMA Source Address Register Channel 12 */
-#define DTADR12 __REG(0x400002c8) /* DMA Target Address Register Channel 12 */
-#define DCMD12 __REG(0x400002cc) /* DMA Command Address Register Channel 12 */
-#define DDADR13 __REG(0x400002d0) /* DMA Descriptor Address Register Channel 13 */
-#define DSADR13 __REG(0x400002d4) /* DMA Source Address Register Channel 13 */
-#define DTADR13 __REG(0x400002d8) /* DMA Target Address Register Channel 13 */
-#define DCMD13 __REG(0x400002dc) /* DMA Command Address Register Channel 13 */
-#define DDADR14 __REG(0x400002e0) /* DMA Descriptor Address Register Channel 14 */
-#define DSADR14 __REG(0x400002e4) /* DMA Source Address Register Channel 14 */
-#define DTADR14 __REG(0x400002e8) /* DMA Target Address Register Channel 14 */
-#define DCMD14 __REG(0x400002ec) /* DMA Command Address Register Channel 14 */
-#define DDADR15 __REG(0x400002f0) /* DMA Descriptor Address Register Channel 15 */
-#define DSADR15 __REG(0x400002f4) /* DMA Source Address Register Channel 15 */
-#define DTADR15 __REG(0x400002f8) /* DMA Target Address Register Channel 15 */
-#define DCMD15 __REG(0x400002fc) /* DMA Command Address Register Channel 15 */
-
-#define DDADR(x) __REG2(0x40000200, (x) << 4)
-#define DSADR(x) __REG2(0x40000204, (x) << 4)
-#define DTADR(x) __REG2(0x40000208, (x) << 4)
-#define DCMD(x) __REG2(0x4000020c, (x) << 4)
-
-#define DDADR_DESCADDR 0xfffffff0 /* Address of next descriptor (mask) */
-#define DDADR_STOP (1 << 0) /* Stop (read / write) */
-
-#define DCMD_INCSRCADDR (1 << 31) /* Source Address Increment Setting. */
-#define DCMD_INCTRGADDR (1 << 30) /* Target Address Increment Setting. */
-#define DCMD_FLOWSRC (1 << 29) /* Flow Control by the source. */
-#define DCMD_FLOWTRG (1 << 28) /* Flow Control by the target. */
-#define DCMD_STARTIRQEN (1 << 22) /* Start Interrupt Enable */
-#define DCMD_ENDIRQEN (1 << 21) /* End Interrupt Enable */
-#define DCMD_ENDIAN (1 << 18) /* Device Endian-ness. */
-#define DCMD_BURST8 (1 << 16) /* 8 byte burst */
-#define DCMD_BURST16 (2 << 16) /* 16 byte burst */
-#define DCMD_BURST32 (3 << 16) /* 32 byte burst */
-#define DCMD_WIDTH1 (1 << 14) /* 1 byte width */
-#define DCMD_WIDTH2 (2 << 14) /* 2 byte width (HalfWord) */
-#define DCMD_WIDTH4 (3 << 14) /* 4 byte width (Word) */
-#define DCMD_LENGTH 0x01fff /* length mask (max = 8K - 1) */
-
-/* default combinations */
-#define DCMD_RXPCDR (DCMD_INCTRGADDR|DCMD_FLOWSRC|DCMD_BURST32|DCMD_WIDTH4)
-#define DCMD_RXMCDR (DCMD_INCTRGADDR|DCMD_FLOWSRC|DCMD_BURST32|DCMD_WIDTH4)
-#define DCMD_TXPCDR (DCMD_INCSRCADDR|DCMD_FLOWTRG|DCMD_BURST32|DCMD_WIDTH4)
-
-
-/*
- * UARTs
- */
-
-/* Full Function UART (FFUART) */
-#define FFUART FFRBR
-#define FFRBR __REG(0x40100000) /* Receive Buffer Register (read only) */
-#define FFTHR __REG(0x40100000) /* Transmit Holding Register (write only) */
-#define FFIER __REG(0x40100004) /* Interrupt Enable Register (read/write) */
-#define FFIIR __REG(0x40100008) /* Interrupt ID Register (read only) */
-#define FFFCR __REG(0x40100008) /* FIFO Control Register (write only) */
-#define FFLCR __REG(0x4010000C) /* Line Control Register (read/write) */
-#define FFMCR __REG(0x40100010) /* Modem Control Register (read/write) */
-#define FFLSR __REG(0x40100014) /* Line Status Register (read only) */
-#define FFMSR __REG(0x40100018) /* Modem Status Register (read only) */
-#define FFSPR __REG(0x4010001C) /* Scratch Pad Register (read/write) */
-#define FFISR __REG(0x40100020) /* Infrared Selection Register (read/write) */
-#define FFDLL __REG(0x40100000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */
-#define FFDLH __REG(0x40100004) /* Divisor Latch High Register (DLAB = 1) (read/write) */
-
-/* Bluetooth UART (BTUART) */
-#define BTUART BTRBR
-#define BTRBR __REG(0x40200000) /* Receive Buffer Register (read only) */
-#define BTTHR __REG(0x40200000) /* Transmit Holding Register (write only) */
-#define BTIER __REG(0x40200004) /* Interrupt Enable Register (read/write) */
-#define BTIIR __REG(0x40200008) /* Interrupt ID Register (read only) */
-#define BTFCR __REG(0x40200008) /* FIFO Control Register (write only) */
-#define BTLCR __REG(0x4020000C) /* Line Control Register (read/write) */
-#define BTMCR __REG(0x40200010) /* Modem Control Register (read/write) */
-#define BTLSR __REG(0x40200014) /* Line Status Register (read only) */
-#define BTMSR __REG(0x40200018) /* Modem Status Register (read only) */
-#define BTSPR __REG(0x4020001C) /* Scratch Pad Register (read/write) */
-#define BTISR __REG(0x40200020) /* Infrared Selection Register (read/write) */
-#define BTDLL __REG(0x40200000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */
-#define BTDLH __REG(0x40200004) /* Divisor Latch High Register (DLAB = 1) (read/write) */
-
-/* Standard UART (STUART) */
-#define STUART STRBR
-#define STRBR __REG(0x40700000) /* Receive Buffer Register (read only) */
-#define STTHR __REG(0x40700000) /* Transmit Holding Register (write only) */
-#define STIER __REG(0x40700004) /* Interrupt Enable Register (read/write) */
-#define STIIR __REG(0x40700008) /* Interrupt ID Register (read only) */
-#define STFCR __REG(0x40700008) /* FIFO Control Register (write only) */
-#define STLCR __REG(0x4070000C) /* Line Control Register (read/write) */
-#define STMCR __REG(0x40700010) /* Modem Control Register (read/write) */
-#define STLSR __REG(0x40700014) /* Line Status Register (read only) */
-#define STMSR __REG(0x40700018) /* Reserved */
-#define STSPR __REG(0x4070001C) /* Scratch Pad Register (read/write) */
-#define STISR __REG(0x40700020) /* Infrared Selection Register (read/write) */
-#define STDLL __REG(0x40700000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */
-#define STDLH __REG(0x40700004) /* Divisor Latch High Register (DLAB = 1) (read/write) */
-
-#define IER_DMAE (1 << 7) /* DMA Requests Enable */
-#define IER_UUE (1 << 6) /* UART Unit Enable */
-#define IER_NRZE (1 << 5) /* NRZ coding Enable */
-#define IER_RTIOE (1 << 4) /* Receiver Time Out Interrupt Enable */
-#define IER_MIE (1 << 3) /* Modem Interrupt Enable */
-#define IER_RLSE (1 << 2) /* Receiver Line Status Interrupt Enable */
-#define IER_TIE (1 << 1) /* Transmit Data request Interrupt Enable */
-#define IER_RAVIE (1 << 0) /* Receiver Data Available Interrupt Enable */
-
-#define IIR_FIFOES1 (1 << 7) /* FIFO Mode Enable Status */
-#define IIR_FIFOES0 (1 << 6) /* FIFO Mode Enable Status */
-#define IIR_TOD (1 << 3) /* Time Out Detected */
-#define IIR_IID2 (1 << 2) /* Interrupt Source Encoded */
-#define IIR_IID1 (1 << 1) /* Interrupt Source Encoded */
-#define IIR_IP (1 << 0) /* Interrupt Pending (active low) */
-
-#define FCR_ITL2 (1 << 7) /* Interrupt Trigger Level */
-#define FCR_ITL1 (1 << 6) /* Interrupt Trigger Level */
-#define FCR_RESETTF (1 << 2) /* Reset Transmitter FIFO */
-#define FCR_RESETRF (1 << 1) /* Reset Receiver FIFO */
-#define FCR_TRFIFOE (1 << 0) /* Transmit and Receive FIFO Enable */
-#define FCR_ITL_1 (0)
-#define FCR_ITL_8 (FCR_ITL1)
-#define FCR_ITL_16 (FCR_ITL2)
-#define FCR_ITL_32 (FCR_ITL2|FCR_ITL1)
-
-#define LCR_DLAB (1 << 7) /* Divisor Latch Access Bit */
-#define LCR_SB (1 << 6) /* Set Break */
-#define LCR_STKYP (1 << 5) /* Sticky Parity */
-#define LCR_EPS (1 << 4) /* Even Parity Select */
-#define LCR_PEN (1 << 3) /* Parity Enable */
-#define LCR_STB (1 << 2) /* Stop Bit */
-#define LCR_WLS1 (1 << 1) /* Word Length Select */
-#define LCR_WLS0 (1 << 0) /* Word Length Select */
-
-#define LSR_FIFOE (1 << 7) /* FIFO Error Status */
-#define LSR_TEMT (1 << 6) /* Transmitter Empty */
-#define LSR_TDRQ (1 << 5) /* Transmit Data Request */
-#define LSR_BI (1 << 4) /* Break Interrupt */
-#define LSR_FE (1 << 3) /* Framing Error */
-#define LSR_PE (1 << 2) /* Parity Error */
-#define LSR_OE (1 << 1) /* Overrun Error */
-#define LSR_DR (1 << 0) /* Data Ready */
-
-#define MCR_LOOP (1 << 4) */
-#define MCR_OUT2 (1 << 3) /* force MSR_DCD in loopback mode */
-#define MCR_OUT1 (1 << 2) /* force MSR_RI in loopback mode */
-#define MCR_RTS (1 << 1) /* Request to Send */
-#define MCR_DTR (1 << 0) /* Data Terminal Ready */
-
-#define MSR_DCD (1 << 7) /* Data Carrier Detect */
-#define MSR_RI (1 << 6) /* Ring Indicator */
-#define MSR_DSR (1 << 5) /* Data Set Ready */
-#define MSR_CTS (1 << 4) /* Clear To Send */
-#define MSR_DDCD (1 << 3) /* Delta Data Carrier Detect */
-#define MSR_TERI (1 << 2) /* Trailing Edge Ring Indicator */
-#define MSR_DDSR (1 << 1) /* Delta Data Set Ready */
-#define MSR_DCTS (1 << 0) /* Delta Clear To Send */
-
-/*
- * IrSR (Infrared Selection Register)
- */
-#define IrSR_OFFSET 0x20
-
-#define IrSR_RXPL_NEG_IS_ZERO (1<<4)
-#define IrSR_RXPL_POS_IS_ZERO 0x0
-#define IrSR_TXPL_NEG_IS_ZERO (1<<3)
-#define IrSR_TXPL_POS_IS_ZERO 0x0
-#define IrSR_XMODE_PULSE_1_6 (1<<2)
-#define IrSR_XMODE_PULSE_3_16 0x0
-#define IrSR_RCVEIR_IR_MODE (1<<1)
-#define IrSR_RCVEIR_UART_MODE 0x0
-#define IrSR_XMITIR_IR_MODE (1<<0)
-#define IrSR_XMITIR_UART_MODE 0x0
-
-#define IrSR_IR_RECEIVE_ON (\
- IrSR_RXPL_NEG_IS_ZERO | \
- IrSR_TXPL_POS_IS_ZERO | \
- IrSR_XMODE_PULSE_3_16 | \
- IrSR_RCVEIR_IR_MODE | \
- IrSR_XMITIR_UART_MODE)
-
-#define IrSR_IR_TRANSMIT_ON (\
- IrSR_RXPL_NEG_IS_ZERO | \
- IrSR_TXPL_POS_IS_ZERO | \
- IrSR_XMODE_PULSE_3_16 | \
- IrSR_RCVEIR_UART_MODE | \
- IrSR_XMITIR_IR_MODE)
-
-/*
- * I2C registers
- */
-
-#define IBMR __REG(0x40301680) /* I2C Bus Monitor Register - IBMR */
-#define IDBR __REG(0x40301688) /* I2C Data Buffer Register - IDBR */
-#define ICR __REG(0x40301690) /* I2C Control Register - ICR */
-#define ISR __REG(0x40301698) /* I2C Status Register - ISR */
-#define ISAR __REG(0x403016A0) /* I2C Slave Address Register - ISAR */
-
-/* ----- Control register bits ---------------------------------------- */
-
-#define ICR_START 0x1 /* start bit */
-#define ICR_STOP 0x2 /* stop bit */
-#define ICR_ACKNAK 0x4 /* send ACK(0) or NAK(1) */
-#define ICR_TB 0x8 /* transfer byte bit */
-#define ICR_MA 0x10 /* master abort */
-#define ICR_SCLE 0x20 /* master clock enable */
-#define ICR_IUE 0x40 /* unit enable */
-#define ICR_GCD 0x80 /* general call disable */
-#define ICR_ITEIE 0x100 /* enable tx interrupts */
-#define ICR_IRFIE 0x200 /* enable rx interrupts */
-#define ICR_BEIE 0x400 /* enable bus error ints */
-#define ICR_SSDIE 0x800 /* slave STOP detected int enable */
-#define ICR_ALDIE 0x1000 /* enable arbitration interrupt */
-#define ICR_SADIE 0x2000 /* slave address detected int enable */
-#define ICR_UR 0x4000 /* unit reset */
-#define ICR_FM 0x8000 /* Fast Mode */
-
-/* ----- Status register bits ----------------------------------------- */
-
-#define ISR_RWM 0x1 /* read/write mode */
-#define ISR_ACKNAK 0x2 /* ack/nak status */
-#define ISR_UB 0x4 /* unit busy */
-#define ISR_IBB 0x8 /* bus busy */
-#define ISR_SSD 0x10 /* slave stop detected */
-#define ISR_ALD 0x20 /* arbitration loss detected */
-#define ISR_ITE 0x40 /* tx buffer empty */
-#define ISR_IRF 0x80 /* rx buffer full */
-#define ISR_GCAD 0x100 /* general call address detected */
-#define ISR_SAD 0x200 /* slave address detected */
-#define ISR_BED 0x400 /* bus error no ACK/NAK */
-
-/*
- * Serial Audio Controller
- */
-
-
-/* FIXME the audio defines collide w/ the SA1111 defines. I don't like these
- * short defines because there is too much chance of namespace collision */
-
-/*#define SACR0 __REG(0x40400000) / Global Control Register */
-/*#define SACR1 __REG(0x40400004) / Serial Audio I 2 S/MSB-Justified Control Register */
-/*#define SASR0 __REG(0x4040000C) / Serial Audio I 2 S/MSB-Justified Interface and FIFO Status Register */
-/*#define SAIMR __REG(0x40400014) / Serial Audio Interrupt Mask Register */
-/*#define SAICR __REG(0x40400018) / Serial Audio Interrupt Clear Register */
-/*#define SADIV __REG(0x40400060) / Audio Clock Divider Register. */
-/*#define SADR __REG(0x40400080) / Serial Audio Data Register (TX and RX FIFO access Register). */
-
-
-/*
- * AC97 Controller registers
- */
-
-#define POCR __REG(0x40500000) /* PCM Out Control Register */
-#define POCR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */
-
-#define PICR __REG(0x40500004) /* PCM In Control Register */
-#define PICR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */
-
-#define MCCR __REG(0x40500008) /* Mic In Control Register */
-#define MCCR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */
-
-#define GCR __REG(0x4050000C) /* Global Control Register */
-#define GCR_CDONE_IE (1 << 19) /* Command Done Interrupt Enable */
-#define GCR_SDONE_IE (1 << 18) /* Status Done Interrupt Enable */
-#define GCR_SECRDY_IEN (1 << 9) /* Secondary Ready Interrupt Enable */
-#define GCR_PRIRDY_IEN (1 << 8) /* Primary Ready Interrupt Enable */
-#define GCR_SECRES_IEN (1 << 5) /* Secondary Resume Interrupt Enable */
-#define GCR_PRIRES_IEN (1 << 4) /* Primary Resume Interrupt Enable */
-#define GCR_ACLINK_OFF (1 << 3) /* AC-link Shut Off */
-#define GCR_WARM_RST (1 << 2) /* AC97 Warm Reset */
-#define GCR_COLD_RST (1 << 1) /* AC'97 Cold Reset (0 = active) */
-#define GCR_GIE (1 << 0) /* Codec GPI Interrupt Enable */
-
-#define POSR __REG(0x40500010) /* PCM Out Status Register */
-#define POSR_FIFOE (1 << 4) /* FIFO error */
-
-#define PISR __REG(0x40500014) /* PCM In Status Register */
-#define PISR_FIFOE (1 << 4) /* FIFO error */
-
-#define MCSR __REG(0x40500018) /* Mic In Status Register */
-#define MCSR_FIFOE (1 << 4) /* FIFO error */
-
-#define GSR __REG(0x4050001C) /* Global Status Register */
-#define GSR_CDONE (1 << 19) /* Command Done */
-#define GSR_SDONE (1 << 18) /* Status Done */
-#define GSR_RDCS (1 << 15) /* Read Completion Status */
-#define GSR_BIT3SLT12 (1 << 14) /* Bit 3 of slot 12 */
-#define GSR_BIT2SLT12 (1 << 13) /* Bit 2 of slot 12 */
-#define GSR_BIT1SLT12 (1 << 12) /* Bit 1 of slot 12 */
-#define GSR_SECRES (1 << 11) /* Secondary Resume Interrupt */
-#define GSR_PRIRES (1 << 10) /* Primary Resume Interrupt */
-#define GSR_SCR (1 << 9) /* Secondary Codec Ready */
-#define GSR_PCR (1 << 8) /* Primary Codec Ready */
-#define GSR_MINT (1 << 7) /* Mic In Interrupt */
-#define GSR_POINT (1 << 6) /* PCM Out Interrupt */
-#define GSR_PIINT (1 << 5) /* PCM In Interrupt */
-#define GSR_MOINT (1 << 2) /* Modem Out Interrupt */
-#define GSR_MIINT (1 << 1) /* Modem In Interrupt */
-#define GSR_GSCI (1 << 0) /* Codec GPI Status Change Interrupt */
-
-#define CAR __REG(0x40500020) /* CODEC Access Register */
-#define CAR_CAIP (1 << 0) /* Codec Access In Progress */
-
-#define PCDR __REG(0x40500040) /* PCM FIFO Data Register */
-#define MCDR __REG(0x40500060) /* Mic-in FIFO Data Register */
-
-#define MOCR __REG(0x40500100) /* Modem Out Control Register */
-#define MOCR_FEIE (1 << 3) /* FIFO Error */
-
-#define MICR __REG(0x40500108) /* Modem In Control Register */
-#define MICR_FEIE (1 << 3) /* FIFO Error */
-
-#define MOSR __REG(0x40500110) /* Modem Out Status Register */
-#define MOSR_FIFOE (1 << 4) /* FIFO error */
-
-#define MISR __REG(0x40500118) /* Modem In Status Register */
-#define MISR_FIFOE (1 << 4) /* FIFO error */
-
-#define MODR __REG(0x40500140) /* Modem FIFO Data Register */
-
-#define PAC_REG_BASE __REG(0x40500200) /* Primary Audio Codec */
-#define SAC_REG_BASE __REG(0x40500300) /* Secondary Audio Codec */
-#define PMC_REG_BASE __REG(0x40500400) /* Primary Modem Codec */
-#define SMC_REG_BASE __REG(0x40500500) /* Secondary Modem Codec */
-
-
-/*
- * USB Device Controller
- */
-#define UDC_RES1 __REG(0x40600004) /* UDC Undocumented - Reserved1 */
-#define UDC_RES2 __REG(0x40600008) /* UDC Undocumented - Reserved2 */
-#define UDC_RES3 __REG(0x4060000C) /* UDC Undocumented - Reserved3 */
-
-#define UDCCR __REG(0x40600000) /* UDC Control Register */
-#define UDCCR_UDE (1 << 0) /* UDC enable */
-#define UDCCR_UDA (1 << 1) /* UDC active */
-#define UDCCR_RSM (1 << 2) /* Device resume */
-#define UDCCR_RESIR (1 << 3) /* Resume interrupt request */
-#define UDCCR_SUSIR (1 << 4) /* Suspend interrupt request */
-#define UDCCR_SRM (1 << 5) /* Suspend/resume interrupt mask */
-#define UDCCR_RSTIR (1 << 6) /* Reset interrupt request */
-#define UDCCR_REM (1 << 7) /* Reset interrupt mask */
-
-#define UDCCS0 __REG(0x40600010) /* UDC Endpoint 0 Control/Status Register */
-#define UDCCS0_OPR (1 << 0) /* OUT packet ready */
-#define UDCCS0_IPR (1 << 1) /* IN packet ready */
-#define UDCCS0_FTF (1 << 2) /* Flush Tx FIFO */
-#define UDCCS0_DRWF (1 << 3) /* Device remote wakeup feature */
-#define UDCCS0_SST (1 << 4) /* Sent stall */
-#define UDCCS0_FST (1 << 5) /* Force stall */
-#define UDCCS0_RNE (1 << 6) /* Receive FIFO no empty */
-#define UDCCS0_SA (1 << 7) /* Setup active */
-
-/* Bulk IN - Endpoint 1,6,11 */
-#define UDCCS1 __REG(0x40600014) /* UDC Endpoint 1 (IN) Control/Status Register */
-#define UDCCS6 __REG(0x40600028) /* UDC Endpoint 6 (IN) Control/Status Register */
-#define UDCCS11 __REG(0x4060003C) /* UDC Endpoint 11 (IN) Control/Status Register */
-
-#define UDCCS_BI_TFS (1 << 0) /* Transmit FIFO service */
-#define UDCCS_BI_TPC (1 << 1) /* Transmit packet complete */
-#define UDCCS_BI_FTF (1 << 2) /* Flush Tx FIFO */
-#define UDCCS_BI_TUR (1 << 3) /* Transmit FIFO underrun */
-#define UDCCS_BI_SST (1 << 4) /* Sent stall */
-#define UDCCS_BI_FST (1 << 5) /* Force stall */
-#define UDCCS_BI_TSP (1 << 7) /* Transmit short packet */
-
-/* Bulk OUT - Endpoint 2,7,12 */
-#define UDCCS2 __REG(0x40600018) /* UDC Endpoint 2 (OUT) Control/Status Register */
-#define UDCCS7 __REG(0x4060002C) /* UDC Endpoint 7 (OUT) Control/Status Register */
-#define UDCCS12 __REG(0x40600040) /* UDC Endpoint 12 (OUT) Control/Status Register */
-
-#define UDCCS_BO_RFS (1 << 0) /* Receive FIFO service */
-#define UDCCS_BO_RPC (1 << 1) /* Receive packet complete */
-#define UDCCS_BO_DME (1 << 3) /* DMA enable */
-#define UDCCS_BO_SST (1 << 4) /* Sent stall */
-#define UDCCS_BO_FST (1 << 5) /* Force stall */
-#define UDCCS_BO_RNE (1 << 6) /* Receive FIFO not empty */
-#define UDCCS_BO_RSP (1 << 7) /* Receive short packet */
-
-/* Isochronous IN - Endpoint 3,8,13 */
-#define UDCCS3 __REG(0x4060001C) /* UDC Endpoint 3 (IN) Control/Status Register */
-#define UDCCS8 __REG(0x40600030) /* UDC Endpoint 8 (IN) Control/Status Register */
-#define UDCCS13 __REG(0x40600044) /* UDC Endpoint 13 (IN) Control/Status Register */
-
-#define UDCCS_II_TFS (1 << 0) /* Transmit FIFO service */
-#define UDCCS_II_TPC (1 << 1) /* Transmit packet complete */
-#define UDCCS_II_FTF (1 << 2) /* Flush Tx FIFO */
-#define UDCCS_II_TUR (1 << 3) /* Transmit FIFO underrun */
-#define UDCCS_II_TSP (1 << 7) /* Transmit short packet */
-
-/* Isochronous OUT - Endpoint 4,9,14 */
-#define UDCCS4 __REG(0x40600020) /* UDC Endpoint 4 (OUT) Control/Status Register */
-#define UDCCS9 __REG(0x40600034) /* UDC Endpoint 9 (OUT) Control/Status Register */
-#define UDCCS14 __REG(0x40600048) /* UDC Endpoint 14 (OUT) Control/Status Register */
-
-#define UDCCS_IO_RFS (1 << 0) /* Receive FIFO service */
-#define UDCCS_IO_RPC (1 << 1) /* Receive packet complete */
-#define UDCCS_IO_ROF (1 << 3) /* Receive overflow */
-#define UDCCS_IO_DME (1 << 3) /* DMA enable */
-#define UDCCS_IO_RNE (1 << 6) /* Receive FIFO not empty */
-#define UDCCS_IO_RSP (1 << 7) /* Receive short packet */
-
-/* Interrupt IN - Endpoint 5,10,15 */
-#define UDCCS5 __REG(0x40600024) /* UDC Endpoint 5 (Interrupt) Control/Status Register */
-#define UDCCS10 __REG(0x40600038) /* UDC Endpoint 10 (Interrupt) Control/Status Register */
-#define UDCCS15 __REG(0x4060004C) /* UDC Endpoint 15 (Interrupt) Control/Status Register */
-
-#define UDCCS_INT_TFS (1 << 0) /* Transmit FIFO service */
-#define UDCCS_INT_TPC (1 << 1) /* Transmit packet complete */
-#define UDCCS_INT_FTF (1 << 2) /* Flush Tx FIFO */
-#define UDCCS_INT_TUR (1 << 3) /* Transmit FIFO underrun */
-#define UDCCS_INT_SST (1 << 4) /* Sent stall */
-#define UDCCS_INT_FST (1 << 5) /* Force stall */
-#define UDCCS_INT_TSP (1 << 7) /* Transmit short packet */
-
-#define UFNRH __REG(0x40600060) /* UDC Frame Number Register High */
-#define UFNRL __REG(0x40600064) /* UDC Frame Number Register Low */
-#define UBCR2 __REG(0x40600068) /* UDC Byte Count Reg 2 */
-#define UBCR4 __REG(0x4060006c) /* UDC Byte Count Reg 4 */
-#define UBCR7 __REG(0x40600070) /* UDC Byte Count Reg 7 */
-#define UBCR9 __REG(0x40600074) /* UDC Byte Count Reg 9 */
-#define UBCR12 __REG(0x40600078) /* UDC Byte Count Reg 12 */
-#define UBCR14 __REG(0x4060007c) /* UDC Byte Count Reg 14 */
-#define UDDR0 __REG(0x40600080) /* UDC Endpoint 0 Data Register */
-#define UDDR1 __REG(0x40600100) /* UDC Endpoint 1 Data Register */
-#define UDDR2 __REG(0x40600180) /* UDC Endpoint 2 Data Register */
-#define UDDR3 __REG(0x40600200) /* UDC Endpoint 3 Data Register */
-#define UDDR4 __REG(0x40600400) /* UDC Endpoint 4 Data Register */
-#define UDDR5 __REG(0x406000A0) /* UDC Endpoint 5 Data Register */
-#define UDDR6 __REG(0x40600600) /* UDC Endpoint 6 Data Register */
-#define UDDR7 __REG(0x40600680) /* UDC Endpoint 7 Data Register */
-#define UDDR8 __REG(0x40600700) /* UDC Endpoint 8 Data Register */
-#define UDDR9 __REG(0x40600900) /* UDC Endpoint 9 Data Register */
-#define UDDR10 __REG(0x406000C0) /* UDC Endpoint 10 Data Register */
-#define UDDR11 __REG(0x40600B00) /* UDC Endpoint 11 Data Register */
-#define UDDR12 __REG(0x40600B80) /* UDC Endpoint 12 Data Register */
-#define UDDR13 __REG(0x40600C00) /* UDC Endpoint 13 Data Register */
-#define UDDR14 __REG(0x40600E00) /* UDC Endpoint 14 Data Register */
-#define UDDR15 __REG(0x406000E0) /* UDC Endpoint 15 Data Register */
-
-#define UICR0 __REG(0x40600050) /* UDC Interrupt Control Register 0 */
-
-#define UICR0_IM0 (1 << 0) /* Interrupt mask ep 0 */
-#define UICR0_IM1 (1 << 1) /* Interrupt mask ep 1 */
-#define UICR0_IM2 (1 << 2) /* Interrupt mask ep 2 */
-#define UICR0_IM3 (1 << 3) /* Interrupt mask ep 3 */
-#define UICR0_IM4 (1 << 4) /* Interrupt mask ep 4 */
-#define UICR0_IM5 (1 << 5) /* Interrupt mask ep 5 */
-#define UICR0_IM6 (1 << 6) /* Interrupt mask ep 6 */
-#define UICR0_IM7 (1 << 7) /* Interrupt mask ep 7 */
-
-#define UICR1 __REG(0x40600054) /* UDC Interrupt Control Register 1 */
-
-#define UICR1_IM8 (1 << 0) /* Interrupt mask ep 8 */
-#define UICR1_IM9 (1 << 1) /* Interrupt mask ep 9 */
-#define UICR1_IM10 (1 << 2) /* Interrupt mask ep 10 */
-#define UICR1_IM11 (1 << 3) /* Interrupt mask ep 11 */
-#define UICR1_IM12 (1 << 4) /* Interrupt mask ep 12 */
-#define UICR1_IM13 (1 << 5) /* Interrupt mask ep 13 */
-#define UICR1_IM14 (1 << 6) /* Interrupt mask ep 14 */
-#define UICR1_IM15 (1 << 7) /* Interrupt mask ep 15 */
-
-#define USIR0 __REG(0x40600058) /* UDC Status Interrupt Register 0 */
-
-#define USIR0_IR0 (1 << 0) /* Interrup request ep 0 */
-#define USIR0_IR1 (1 << 1) /* Interrup request ep 1 */
-#define USIR0_IR2 (1 << 2) /* Interrup request ep 2 */
-#define USIR0_IR3 (1 << 3) /* Interrup request ep 3 */
-#define USIR0_IR4 (1 << 4) /* Interrup request ep 4 */
-#define USIR0_IR5 (1 << 5) /* Interrup request ep 5 */
-#define USIR0_IR6 (1 << 6) /* Interrup request ep 6 */
-#define USIR0_IR7 (1 << 7) /* Interrup request ep 7 */
-
-#define USIR1 __REG(0x4060005C) /* UDC Status Interrupt Register 1 */
-
-#define USIR1_IR8 (1 << 0) /* Interrup request ep 8 */
-#define USIR1_IR9 (1 << 1) /* Interrup request ep 9 */
-#define USIR1_IR10 (1 << 2) /* Interrup request ep 10 */
-#define USIR1_IR11 (1 << 3) /* Interrup request ep 11 */
-#define USIR1_IR12 (1 << 4) /* Interrup request ep 12 */
-#define USIR1_IR13 (1 << 5) /* Interrup request ep 13 */
-#define USIR1_IR14 (1 << 6) /* Interrup request ep 14 */
-#define USIR1_IR15 (1 << 7) /* Interrup request ep 15 */
-
-
-/*
- * Fast Infrared Communication Port
- */
-
-#define ICCR0 __REG(0x40800000) /* ICP Control Register 0 */
-#define ICCR1 __REG(0x40800004) /* ICP Control Register 1 */
-#define ICCR2 __REG(0x40800008) /* ICP Control Register 2 */
-#define ICDR __REG(0x4080000c) /* ICP Data Register */
-#define ICSR0 __REG(0x40800014) /* ICP Status Register 0 */
-#define ICSR1 __REG(0x40800018) /* ICP Status Register 1 */
-
-
-/*
- * Real Time Clock
- */
-
-#define RCNR __REG(0x40900000) /* RTC Count Register */
-#define RTAR __REG(0x40900004) /* RTC Alarm Register */
-#define RTSR __REG(0x40900008) /* RTC Status Register */
-#define RTTR __REG(0x4090000C) /* RTC Timer Trim Register */
-
-#define RTSR_HZE (1 << 3) /* HZ interrupt enable */
-#define RTSR_ALE (1 << 2) /* RTC alarm interrupt enable */
-#define RTSR_HZ (1 << 1) /* HZ rising-edge detected */
-#define RTSR_AL (1 << 0) /* RTC alarm detected */
-
-
-/*
- * OS Timer & Match Registers
- */
-
-#define OSMR0 __REG(0x40A00000) /* */
-#define OSMR1 __REG(0x40A00004) /* */
-#define OSMR2 __REG(0x40A00008) /* */
-#define OSMR3 __REG(0x40A0000C) /* */
-#define OSCR __REG(0x40A00010) /* OS Timer Counter Register */
-#define OSSR __REG(0x40A00014) /* OS Timer Status Register */
-#define OWER __REG(0x40A00018) /* OS Timer Watchdog Enable Register */
-#define OIER __REG(0x40A0001C) /* OS Timer Interrupt Enable Register */
-
-#define OSSR_M3 (1 << 3) /* Match status channel 3 */
-#define OSSR_M2 (1 << 2) /* Match status channel 2 */
-#define OSSR_M1 (1 << 1) /* Match status channel 1 */
-#define OSSR_M0 (1 << 0) /* Match status channel 0 */
-
-#define OWER_WME (1 << 0) /* Watchdog Match Enable */
-
-#define OIER_E3 (1 << 3) /* Interrupt enable channel 3 */
-#define OIER_E2 (1 << 2) /* Interrupt enable channel 2 */
-#define OIER_E1 (1 << 1) /* Interrupt enable channel 1 */
-#define OIER_E0 (1 << 0) /* Interrupt enable channel 0 */
-
-
-/*
- * Pulse Width Modulator
- */
-
-#define PWM_CTRL0 __REG(0x40B00000) /* PWM 0 Control Register */
-#define PWM_PWDUTY0 __REG(0x40B00004) /* PWM 0 Duty Cycle Register */
-#define PWM_PERVAL0 __REG(0x40B00008) /* PWM 0 Period Control Register */
-
-#define PWM_CTRL1 __REG(0x40C00000) /* PWM 1Control Register */
-#define PWM_PWDUTY1 __REG(0x40C00004) /* PWM 1 Duty Cycle Register */
-#define PWM_PERVAL1 __REG(0x40C00008) /* PWM 1 Period Control Register */
-
-
-/*
- * Interrupt Controller
- */
-
-#define ICIP __REG(0x40D00000) /* Interrupt Controller IRQ Pending Register */
-#define ICMR __REG(0x40D00004) /* Interrupt Controller Mask Register */
-#define ICLR __REG(0x40D00008) /* Interrupt Controller Level Register */
-#define ICFP __REG(0x40D0000C) /* Interrupt Controller FIQ Pending Register */
-#define ICPR __REG(0x40D00010) /* Interrupt Controller Pending Register */
-#define ICCR __REG(0x40D00014) /* Interrupt Controller Control Register */
-
-
-/*
- * General Purpose I/O
- */
-
-#define GPLR0 __REG(0x40E00000) /* GPIO Pin-Level Register GPIO<31:0> */
-#define GPLR1 __REG(0x40E00004) /* GPIO Pin-Level Register GPIO<63:32> */
-#define GPLR2 __REG(0x40E00008) /* GPIO Pin-Level Register GPIO<80:64> */
-
-#define GPDR0 __REG(0x40E0000C) /* GPIO Pin Direction Register GPIO<31:0> */
-#define GPDR1 __REG(0x40E00010) /* GPIO Pin Direction Register GPIO<63:32> */
-#define GPDR2 __REG(0x40E00014) /* GPIO Pin Direction Register GPIO<80:64> */
-
-#define GPSR0 __REG(0x40E00018) /* GPIO Pin Output Set Register GPIO<31:0> */
-#define GPSR1 __REG(0x40E0001C) /* GPIO Pin Output Set Register GPIO<63:32> */
-#define GPSR2 __REG(0x40E00020) /* GPIO Pin Output Set Register GPIO<80:64> */
-
-#define GPCR0 __REG(0x40E00024) /* GPIO Pin Output Clear Register GPIO<31:0> */
-#define GPCR1 __REG(0x40E00028) /* GPIO Pin Output Clear Register GPIO <63:32> */
-#define GPCR2 __REG(0x40E0002C) /* GPIO Pin Output Clear Register GPIO <80:64> */
-
-#define GRER0 __REG(0x40E00030) /* GPIO Rising-Edge Detect Register GPIO<31:0> */
-#define GRER1 __REG(0x40E00034) /* GPIO Rising-Edge Detect Register GPIO<63:32> */
-#define GRER2 __REG(0x40E00038) /* GPIO Rising-Edge Detect Register GPIO<80:64> */
-
-#define GFER0 __REG(0x40E0003C) /* GPIO Falling-Edge Detect Register GPIO<31:0> */
-#define GFER1 __REG(0x40E00040) /* GPIO Falling-Edge Detect Register GPIO<63:32> */
-#define GFER2 __REG(0x40E00044) /* GPIO Falling-Edge Detect Register GPIO<80:64> */
-
-#define GEDR0 __REG(0x40E00048) /* GPIO Edge Detect Status Register GPIO<31:0> */
-#define GEDR1 __REG(0x40E0004C) /* GPIO Edge Detect Status Register GPIO<63:32> */
-#define GEDR2 __REG(0x40E00050) /* GPIO Edge Detect Status Register GPIO<80:64> */
-
-#define GAFR0_L __REG(0x40E00054) /* GPIO Alternate Function Select Register GPIO<15:0> */
-#define GAFR0_U __REG(0x40E00058) /* GPIO Alternate Function Select Register GPIO<31:16> */
-#define GAFR1_L __REG(0x40E0005C) /* GPIO Alternate Function Select Register GPIO<47:32> */
-#define GAFR1_U __REG(0x40E00060) /* GPIO Alternate Function Select Register GPIO<63:48> */
-#define GAFR2_L __REG(0x40E00064) /* GPIO Alternate Function Select Register GPIO<79:64> */
-#define GAFR2_U __REG(0x40E00068) /* GPIO Alternate Function Select Register GPIO 80 */
-
-/* More handy macros. The argument is a literal GPIO number. */
-
-#define GPIO_bit(x) (1 << ((x) & 0x1f))
-#define GPLR(x) __REG2(0x40E00000, ((x) & 0x60) >> 3)
-#define GPDR(x) __REG2(0x40E0000C, ((x) & 0x60) >> 3)
-#define GPSR(x) __REG2(0x40E00018, ((x) & 0x60) >> 3)
-#define GPCR(x) __REG2(0x40E00024, ((x) & 0x60) >> 3)
-#define GRER(x) __REG2(0x40E00030, ((x) & 0x60) >> 3)
-#define GFER(x) __REG2(0x40E0003C, ((x) & 0x60) >> 3)
-#define GEDR(x) __REG2(0x40E00048, ((x) & 0x60) >> 3)
-#define GAFR(x) __REG2(0x40E00054, ((x) & 0x70) >> 2)
-
-/* GPIO alternate function assignments */
-
-#define GPIO1_RST 1 /* reset */
-#define GPIO6_MMCCLK 6 /* MMC Clock */
-#define GPIO8_48MHz 7 /* 48 MHz clock output */
-#define GPIO8_MMCCS0 8 /* MMC Chip Select 0 */
-#define GPIO9_MMCCS1 9 /* MMC Chip Select 1 */
-#define GPIO10_RTCCLK 10 /* real time clock (1 Hz) */
-#define GPIO11_3_6MHz 11 /* 3.6 MHz oscillator out */
-#define GPIO12_32KHz 12 /* 32 kHz out */
-#define GPIO13_MBGNT 13 /* memory controller grant */
-#define GPIO14_MBREQ 14 /* alternate bus master request */
-#define GPIO15_nCS_1 15 /* chip select 1 */
-#define GPIO16_PWM0 16 /* PWM0 output */
-#define GPIO17_PWM1 17 /* PWM1 output */
-#define GPIO18_RDY 18 /* Ext. Bus Ready */
-#define GPIO19_DREQ1 19 /* External DMA Request */
-#define GPIO20_DREQ0 20 /* External DMA Request */
-#define GPIO23_SCLK 23 /* SSP clock */
-#define GPIO24_SFRM 24 /* SSP Frame */
-#define GPIO25_STXD 25 /* SSP transmit */
-#define GPIO26_SRXD 26 /* SSP receive */
-#define GPIO27_SEXTCLK 27 /* SSP ext_clk */
-#define GPIO28_BITCLK 28 /* AC97/I2S bit_clk */
-#define GPIO29_SDATA_IN 29 /* AC97 Sdata_in0 / I2S Sdata_in */
-#define GPIO30_SDATA_OUT 30 /* AC97/I2S Sdata_out */
-#define GPIO31_SYNC 31 /* AC97/I2S sync */
-#define GPIO32_SDATA_IN1 32 /* AC97 Sdata_in1 */
-#define GPIO33_nCS_5 33 /* chip select 5 */
-#define GPIO34_FFRXD 34 /* FFUART receive */
-#define GPIO34_MMCCS0 34 /* MMC Chip Select 0 */
-#define GPIO35_FFCTS 35 /* FFUART Clear to send */
-#define GPIO36_FFDCD 36 /* FFUART Data carrier detect */
-#define GPIO37_FFDSR 37 /* FFUART data set ready */
-#define GPIO38_FFRI 38 /* FFUART Ring Indicator */
-#define GPIO39_MMCCS1 39 /* MMC Chip Select 1 */
-#define GPIO39_FFTXD 39 /* FFUART transmit data */
-#define GPIO40_FFDTR 40 /* FFUART data terminal Ready */
-#define GPIO41_FFRTS 41 /* FFUART request to send */
-#define GPIO42_BTRXD 42 /* BTUART receive data */
-#define GPIO43_BTTXD 43 /* BTUART transmit data */
-#define GPIO44_BTCTS 44 /* BTUART clear to send */
-#define GPIO45_BTRTS 45 /* BTUART request to send */
-#define GPIO46_ICPRXD 46 /* ICP receive data */
-#define GPIO46_STRXD 46 /* STD_UART receive data */
-#define GPIO47_ICPTXD 47 /* ICP transmit data */
-#define GPIO47_STTXD 47 /* STD_UART transmit data */
-#define GPIO48_nPOE 48 /* Output Enable for Card Space */
-#define GPIO49_nPWE 49 /* Write Enable for Card Space */
-#define GPIO50_nPIOR 50 /* I/O Read for Card Space */
-#define GPIO51_nPIOW 51 /* I/O Write for Card Space */
-#define GPIO52_nPCE_1 52 /* Card Enable for Card Space */
-#define GPIO53_nPCE_2 53 /* Card Enable for Card Space */
-#define GPIO53_MMCCLK 53 /* MMC Clock */
-#define GPIO54_MMCCLK 54 /* MMC Clock */
-#define GPIO54_pSKTSEL 54 /* Socket Select for Card Space */
-#define GPIO55_nPREG 55 /* Card Address bit 26 */
-#define GPIO56_nPWAIT 56 /* Wait signal for Card Space */
-#define GPIO57_nIOIS16 57 /* Bus Width select for I/O Card Space */
-#define GPIO58_LDD_0 58 /* LCD data pin 0 */
-#define GPIO59_LDD_1 59 /* LCD data pin 1 */
-#define GPIO60_LDD_2 60 /* LCD data pin 2 */
-#define GPIO61_LDD_3 61 /* LCD data pin 3 */
-#define GPIO62_LDD_4 62 /* LCD data pin 4 */
-#define GPIO63_LDD_5 63 /* LCD data pin 5 */
-#define GPIO64_LDD_6 64 /* LCD data pin 6 */
-#define GPIO65_LDD_7 65 /* LCD data pin 7 */
-#define GPIO66_LDD_8 66 /* LCD data pin 8 */
-#define GPIO66_MBREQ 66 /* alternate bus master req */
-#define GPIO67_LDD_9 67 /* LCD data pin 9 */
-#define GPIO67_MMCCS0 67 /* MMC Chip Select 0 */
-#define GPIO68_LDD_10 68 /* LCD data pin 10 */
-#define GPIO68_MMCCS1 68 /* MMC Chip Select 1 */
-#define GPIO69_LDD_11 69 /* LCD data pin 11 */
-#define GPIO69_MMCCLK 69 /* MMC_CLK */
-#define GPIO70_LDD_12 70 /* LCD data pin 12 */
-#define GPIO70_RTCCLK 70 /* Real Time clock (1 Hz) */
-#define GPIO71_LDD_13 71 /* LCD data pin 13 */
-#define GPIO71_3_6MHz 71 /* 3.6 MHz Oscillator clock */
-#define GPIO72_LDD_14 72 /* LCD data pin 14 */
-#define GPIO72_32kHz 72 /* 32 kHz clock */
-#define GPIO73_LDD_15 73 /* LCD data pin 15 */
-#define GPIO73_MBGNT 73 /* Memory controller grant */
-#define GPIO74_LCD_FCLK 74 /* LCD Frame clock */
-#define GPIO75_LCD_LCLK 75 /* LCD line clock */
-#define GPIO76_LCD_PCLK 76 /* LCD Pixel clock */
-#define GPIO77_LCD_ACBIAS 77 /* LCD AC Bias */
-#define GPIO78_nCS_2 78 /* chip select 2 */
-#define GPIO79_nCS_3 79 /* chip select 3 */
-#define GPIO80_nCS_4 80 /* chip select 4 */
-
-/* GPIO alternate function mode & direction */
-
-#define GPIO_IN 0x000
-#define GPIO_OUT 0x080
-#define GPIO_ALT_FN_1_IN 0x100
-#define GPIO_ALT_FN_1_OUT 0x180
-#define GPIO_ALT_FN_2_IN 0x200
-#define GPIO_ALT_FN_2_OUT 0x280
-#define GPIO_ALT_FN_3_IN 0x300
-#define GPIO_ALT_FN_3_OUT 0x380
-#define GPIO_MD_MASK_NR 0x07f
-#define GPIO_MD_MASK_DIR 0x080
-#define GPIO_MD_MASK_FN 0x300
-
-#define GPIO1_RTS_MD ( 1 | GPIO_ALT_FN_1_IN)
-#define GPIO6_MMCCLK_MD ( 6 | GPIO_ALT_FN_1_OUT)
-#define GPIO8_48MHz_MD ( 8 | GPIO_ALT_FN_1_OUT)
-#define GPIO8_MMCCS0_MD ( 8 | GPIO_ALT_FN_1_OUT)
-#define GPIO9_MMCCS1_MD ( 9 | GPIO_ALT_FN_1_OUT)
-#define GPIO10_RTCCLK_MD (10 | GPIO_ALT_FN_1_OUT)
-#define GPIO11_3_6MHz_MD (11 | GPIO_ALT_FN_1_OUT)
-#define GPIO12_32KHz_MD (12 | GPIO_ALT_FN_1_OUT)
-#define GPIO13_MBGNT_MD (13 | GPIO_ALT_FN_2_OUT)
-#define GPIO14_MBREQ_MD (14 | GPIO_ALT_FN_1_IN)
-#define GPIO15_nCS_1_MD (15 | GPIO_ALT_FN_2_OUT)
-#define GPIO16_PWM0_MD (16 | GPIO_ALT_FN_2_OUT)
-#define GPIO17_PWM1_MD (17 | GPIO_ALT_FN_2_OUT)
-#define GPIO18_RDY_MD (18 | GPIO_ALT_FN_1_IN)
-#define GPIO19_DREQ1_MD (19 | GPIO_ALT_FN_1_IN)
-#define GPIO20_DREQ0_MD (20 | GPIO_ALT_FN_1_IN)
-#define GPIO23_SCLK_md (23 | GPIO_ALT_FN_2_OUT)
-#define GPIO24_SFRM_MD (24 | GPIO_ALT_FN_2_OUT)
-#define GPIO25_STXD_MD (25 | GPIO_ALT_FN_2_OUT)
-#define GPIO26_SRXD_MD (26 | GPIO_ALT_FN_1_IN)
-#define GPIO27_SEXTCLK_MD (27 | GPIO_ALT_FN_1_IN)
-#define GPIO28_BITCLK_AC97_MD (28 | GPIO_ALT_FN_1_IN)
-#define GPIO28_BITCLK_I2S_MD (28 | GPIO_ALT_FN_2_IN)
-#define GPIO29_SDATA_IN_AC97_MD (29 | GPIO_ALT_FN_1_IN)
-#define GPIO29_SDATA_IN_I2S_MD (29 | GPIO_ALT_FN_2_IN)
-#define GPIO30_SDATA_OUT_AC97_MD (30 | GPIO_ALT_FN_2_OUT)
-#define GPIO30_SDATA_OUT_I2S_MD (30 | GPIO_ALT_FN_1_OUT)
-#define GPIO31_SYNC_AC97_MD (31 | GPIO_ALT_FN_2_OUT)
-#define GPIO31_SYNC_I2S_MD (31 | GPIO_ALT_FN_1_OUT)
-#define GPIO32_SDATA_IN1_AC97_MD (32 | GPIO_ALT_FN_1_IN)
-#define GPIO33_nCS_5_MD (33 | GPIO_ALT_FN_2_OUT)
-#define GPIO34_FFRXD_MD (34 | GPIO_ALT_FN_1_IN)
-#define GPIO34_MMCCS0_MD (34 | GPIO_ALT_FN_2_OUT)
-#define GPIO35_FFCTS_MD (35 | GPIO_ALT_FN_1_IN)
-#define GPIO36_FFDCD_MD (36 | GPIO_ALT_FN_1_IN)
-#define GPIO37_FFDSR_MD (37 | GPIO_ALT_FN_1_IN)
-#define GPIO38_FFRI_MD (38 | GPIO_ALT_FN_1_IN)
-#define GPIO39_MMCCS1_MD (39 | GPIO_ALT_FN_1_OUT)
-#define GPIO39_FFTXD_MD (39 | GPIO_ALT_FN_2_OUT)
-#define GPIO40_FFDTR_MD (40 | GPIO_ALT_FN_2_OUT)
-#define GPIO41_FFRTS_MD (41 | GPIO_ALT_FN_2_OUT)
-#define GPIO42_BTRXD_MD (42 | GPIO_ALT_FN_1_IN)
-#define GPIO43_BTTXD_MD (43 | GPIO_ALT_FN_2_OUT)
-#define GPIO44_BTCTS_MD (44 | GPIO_ALT_FN_1_IN)
-#define GPIO45_BTRTS_MD (45 | GPIO_ALT_FN_2_OUT)
-#define GPIO46_ICPRXD_MD (46 | GPIO_ALT_FN_1_IN)
-#define GPIO46_STRXD_MD (46 | GPIO_ALT_FN_2_IN)
-#define GPIO47_ICPTXD_MD (47 | GPIO_ALT_FN_2_OUT)
-#define GPIO47_STTXD_MD (47 | GPIO_ALT_FN_1_OUT)
-#define GPIO48_nPOE_MD (48 | GPIO_ALT_FN_2_OUT)
-#define GPIO49_nPWE_MD (49 | GPIO_ALT_FN_2_OUT)
-#define GPIO50_nPIOR_MD (50 | GPIO_ALT_FN_2_OUT)
-#define GPIO51_nPIOW_MD (51 | GPIO_ALT_FN_2_OUT)
-#define GPIO52_nPCE_1_MD (52 | GPIO_ALT_FN_2_OUT)
-#define GPIO53_nPCE_2_MD (53 | GPIO_ALT_FN_2_OUT)
-#define GPIO53_MMCCLK_MD (53 | GPIO_ALT_FN_1_OUT)
-#define GPIO54_MMCCLK_MD (54 | GPIO_ALT_FN_1_OUT)
-#define GPIO54_pSKTSEL_MD (54 | GPIO_ALT_FN_2_OUT)
-#define GPIO55_nPREG_MD (55 | GPIO_ALT_FN_2_OUT)
-#define GPIO56_nPWAIT_MD (56 | GPIO_ALT_FN_1_IN)
-#define GPIO57_nIOIS16_MD (57 | GPIO_ALT_FN_1_IN)
-#define GPIO58_LDD_0_MD (58 | GPIO_ALT_FN_2_OUT)
-#define GPIO59_LDD_1_MD (59 | GPIO_ALT_FN_2_OUT)
-#define GPIO60_LDD_2_MD (60 | GPIO_ALT_FN_2_OUT)
-#define GPIO61_LDD_3_MD (61 | GPIO_ALT_FN_2_OUT)
-#define GPIO62_LDD_4_MD (62 | GPIO_ALT_FN_2_OUT)
-#define GPIO63_LDD_5_MD (63 | GPIO_ALT_FN_2_OUT)
-#define GPIO64_LDD_6_MD (64 | GPIO_ALT_FN_2_OUT)
-#define GPIO65_LDD_7_MD (65 | GPIO_ALT_FN_2_OUT)
-#define GPIO66_LDD_8_MD (66 | GPIO_ALT_FN_2_OUT)
-#define GPIO66_MBREQ_MD (66 | GPIO_ALT_FN_1_IN)
-#define GPIO67_LDD_9_MD (67 | GPIO_ALT_FN_2_OUT)
-#define GPIO67_MMCCS0_MD (67 | GPIO_ALT_FN_1_OUT)
-#define GPIO68_LDD_10_MD (68 | GPIO_ALT_FN_2_OUT)
-#define GPIO68_MMCCS1_MD (68 | GPIO_ALT_FN_1_OUT)
-#define GPIO69_LDD_11_MD (69 | GPIO_ALT_FN_2_OUT)
-#define GPIO69_MMCCLK_MD (69 | GPIO_ALT_FN_1_OUT)
-#define GPIO70_LDD_12_MD (70 | GPIO_ALT_FN_2_OUT)
-#define GPIO70_RTCCLK_MD (70 | GPIO_ALT_FN_1_OUT)
-#define GPIO71_LDD_13_MD (71 | GPIO_ALT_FN_2_OUT)
-#define GPIO71_3_6MHz_MD (71 | GPIO_ALT_FN_1_OUT)
-#define GPIO72_LDD_14_MD (72 | GPIO_ALT_FN_2_OUT)
-#define GPIO72_32kHz_MD (72 | GPIO_ALT_FN_1_OUT)
-#define GPIO73_LDD_15_MD (73 | GPIO_ALT_FN_2_OUT)
-#define GPIO73_MBGNT_MD (73 | GPIO_ALT_FN_1_OUT)
-#define GPIO74_LCD_FCLK_MD (74 | GPIO_ALT_FN_2_OUT)
-#define GPIO75_LCD_LCLK_MD (75 | GPIO_ALT_FN_2_OUT)
-#define GPIO76_LCD_PCLK_MD (76 | GPIO_ALT_FN_2_OUT)
-#define GPIO77_LCD_ACBIAS_MD (77 | GPIO_ALT_FN_2_OUT)
-#define GPIO78_nCS_2_MD (78 | GPIO_ALT_FN_2_OUT)
-#define GPIO79_nCS_3_MD (79 | GPIO_ALT_FN_2_OUT)
-#define GPIO80_nCS_4_MD (80 | GPIO_ALT_FN_2_OUT)
-
-
-/*
- * Power Manager
- */
-
-#define PMCR __REG(0x40F00000) /* Power Manager Control Register */
-#define PSSR __REG(0x40F00004) /* Power Manager Sleep Status Register */
-#define PSPR __REG(0x40F00008) /* Power Manager Scratch Pad Register */
-#define PWER __REG(0x40F0000C) /* Power Manager Wake-up Enable Register */
-#define PRER __REG(0x40F00010) /* Power Manager GPIO Rising-Edge Detect Enable Register */
-#define PFER __REG(0x40F00014) /* Power Manager GPIO Falling-Edge Detect Enable Register */
-#define PEDR __REG(0x40F00018) /* Power Manager GPIO Edge Detect Status Register */
-#define PCFR __REG(0x40F0001C) /* Power Manager General Configuration Register */
-#define PGSR0 __REG(0x40F00020) /* Power Manager GPIO Sleep State Register for GP[31-0] */
-#define PGSR1 __REG(0x40F00024) /* Power Manager GPIO Sleep State Register for GP[63-32] */
-#define PGSR2 __REG(0x40F00028) /* Power Manager GPIO Sleep State Register for GP[84-64] */
-#define RCSR __REG(0x40F00030) /* Reset Controller Status Register */
-
-#define PSSR_RDH (1 << 5) /* Read Disable Hold */
-#define PSSR_PH (1 << 4) /* Peripheral Control Hold */
-#define PSSR_VFS (1 << 2) /* VDD Fault Status */
-#define PSSR_BFS (1 << 1) /* Battery Fault Status */
-#define PSSR_SSS (1 << 0) /* Software Sleep Status */
-
-#define PCFR_DS (1 << 3) /* Deep Sleep Mode */
-#define PCFR_FS (1 << 2) /* Float Static Chip Selects */
-#define PCFR_FP (1 << 1) /* Float PCMCIA controls */
-#define PCFR_OPDE (1 << 0) /* 3.6864 MHz oscillator power-down enable */
-
-#define RCSR_GPR (1 << 3) /* GPIO Reset */
-#define RCSR_SMR (1 << 2) /* Sleep Mode */
-#define RCSR_WDR (1 << 1) /* Watchdog Reset */
-#define RCSR_HWR (1 << 0) /* Hardware Reset */
-
-
-/*
- * SSP Serial Port Registers
- */
-
-#define SSCR0 __REG(0x41000000) /* SSP Control Register 0 */
-#define SSCR1 __REG(0x41000004) /* SSP Control Register 1 */
-#define SSSR __REG(0x41000008) /* SSP Status Register */
-#define SSITR __REG(0x4100000C) /* SSP Interrupt Test Register */
-#define SSDR __REG(0x41000010) /* (Write / Read) SSP Data Write Register/SSP Data Read Register */
-
-
-/*
- * MultiMediaCard (MMC) controller
- */
-
-#define MMC_STRPCL __REG(0x41100000) /* Control to start and stop MMC clock */
-#define MMC_STAT __REG(0x41100004) /* MMC Status Register (read only) */
-#define MMC_CLKRT __REG(0x41100008) /* MMC clock rate */
-#define MMC_SPI __REG(0x4110000c) /* SPI mode control bits */
-#define MMC_CMDAT __REG(0x41100010) /* Command/response/data sequence control */
-#define MMC_RESTO __REG(0x41100014) /* Expected response time out */
-#define MMC_RDTO __REG(0x41100018) /* Expected data read time out */
-#define MMC_BLKLEN __REG(0x4110001c) /* Block length of data transaction */
-#define MMC_NOB __REG(0x41100020) /* Number of blocks, for block mode */
-#define MMC_PRTBUF __REG(0x41100024) /* Partial MMC_TXFIFO FIFO written */
-#define MMC_I_MASK __REG(0x41100028) /* Interrupt Mask */
-#define MMC_I_REG __REG(0x4110002c) /* Interrupt Register (read only) */
-#define MMC_CMD __REG(0x41100030) /* Index of current command */
-#define MMC_ARGH __REG(0x41100034) /* MSW part of the current command argument */
-#define MMC_ARGL __REG(0x41100038) /* LSW part of the current command argument */
-#define MMC_RES __REG(0x4110003c) /* Response FIFO (read only) */
-#define MMC_RXFIFO __REG(0x41100040) /* Receive FIFO (read only) */
-#define MMC_TXFIFO __REG(0x41100044) /* Transmit FIFO (write only) */
-
-
-/*
- * Core Clock
- */
-
-#define CCCR __REG(0x41300000) /* Core Clock Configuration Register */
-#define CKEN __REG(0x41300004) /* Clock Enable Register */
-#define OSCC __REG(0x41300008) /* Oscillator Configuration Register */
-
-#define CCCR_N_MASK 0x0380 /* Run Mode Frequency to Turbo Mode Frequency Multiplier */
-#define CCCR_M_MASK 0x0060 /* Memory Frequency to Run Mode Frequency Multiplier */
-#define CCCR_L_MASK 0x001f /* Crystal Frequency to Memory Frequency Multiplier */
-
-#define CKEN16_LCD (1 << 16) /* LCD Unit Clock Enable */
-#define CKEN14_I2C (1 << 14) /* I2C Unit Clock Enable */
-#define CKEN13_FICP (1 << 13) /* FICP Unit Clock Enable */
-#define CKEN12_MMC (1 << 12) /* MMC Unit Clock Enable */
-#define CKEN11_USB (1 << 11) /* USB Unit Clock Enable */
-#define CKEN8_I2S (1 << 8) /* I2S Unit Clock Enable */
-#define CKEN7_BTUART (1 << 7) /* BTUART Unit Clock Enable */
-#define CKEN6_FFUART (1 << 6) /* FFUART Unit Clock Enable */
-#define CKEN5_STUART (1 << 5) /* STUART Unit Clock Enable */
-#define CKEN3_SSP (1 << 3) /* SSP Unit Clock Enable */
-#define CKEN2_AC97 (1 << 2) /* AC97 Unit Clock Enable */
-#define CKEN1_PWM1 (1 << 1) /* PWM1 Clock Enable */
-#define CKEN0_PWM0 (1 << 0) /* PWM0 Clock Enable */
-
-#define OSCC_OON (1 << 1) /* 32.768kHz OON (write-once only bit) */
-#define OSCC_OOK (1 << 0) /* 32.768kHz OOK (read-only bit) */
-
-#define CCCR_L09 (0x1F)
-#define CCCR_L27 (0x1)
-#define CCCR_L32 (0x2)
-#define CCCR_L36 (0x3)
-#define CCCR_L40 (0x4)
-#define CCCR_L45 (0x5)
-
-#define CCCR_M1 (0x1 << 5)
-#define CCCR_M2 (0x2 << 5)
-#define CCCR_M4 (0x3 << 5)
-
-#define CCCR_N10 (0x2 << 7)
-#define CCCR_N15 (0x3 << 7)
-#define CCCR_N20 (0x4 << 7)
-#define CCCR_N25 (0x5 << 7)
-#define CCCR_N30 (0x6 << 7)
-
-/*
- * LCD
- */
-
-#define LCCR0 __REG(0x44000000) /* LCD Controller Control Register 0 */
-#define LCCR1 __REG(0x44000004) /* LCD Controller Control Register 1 */
-#define LCCR2 __REG(0x44000008) /* LCD Controller Control Register 2 */
-#define LCCR3 __REG(0x4400000C) /* LCD Controller Control Register 3 */
-#define DFBR0 __REG(0x44000020) /* DMA Channel 0 Frame Branch Register */
-#define DFBR1 __REG(0x44000024) /* DMA Channel 1 Frame Branch Register */
-#define LCSR __REG(0x44000038) /* LCD Controller Status Register */
-#define LIIDR __REG(0x4400003C) /* LCD Controller Interrupt ID Register */
-#define TMEDRGBR __REG(0x44000040) /* TMED RGB Seed Register */
-#define TMEDCR __REG(0x44000044) /* TMED Control Register */
-
-#define FDADR0 __REG(0x44000200) /* DMA Channel 0 Frame Descriptor Address Register */
-#define FSADR0 __REG(0x44000204) /* DMA Channel 0 Frame Source Address Register */
-#define FIDR0 __REG(0x44000208) /* DMA Channel 0 Frame ID Register */
-#define LDCMD0 __REG(0x4400020C) /* DMA Channel 0 Command Register */
-#define FDADR1 __REG(0x44000210) /* DMA Channel 1 Frame Descriptor Address Register */
-#define FSADR1 __REG(0x44000214) /* DMA Channel 1 Frame Source Address Register */
-#define FIDR1 __REG(0x44000218) /* DMA Channel 1 Frame ID Register */
-#define LDCMD1 __REG(0x4400021C) /* DMA Channel 1 Command Register */
-
-#define LCCR0_ENB (1 << 0) /* LCD Controller enable */
-#define LCCR0_CMS (1 << 1) /* Color = 0, Monochrome = 1 */
-#define LCCR0_SDS (1 << 2) /* Single Panel = 0, Dual Panel = 1 */
-#define LCCR0_LDM (1 << 3) /* LCD Disable Done Mask */
-#define LCCR0_SFM (1 << 4) /* Start of frame mask */
-#define LCCR0_IUM (1 << 5) /* Input FIFO underrun mask */
-#define LCCR0_EFM (1 << 6) /* End of Frame mask */
-#define LCCR0_PAS (1 << 7) /* Passive = 0, Active = 1 */
-#define LCCR0_BLE (1 << 8) /* Little Endian = 0, Big Endian = 1 */
-#define LCCR0_DPD (1 << 9) /* Double Pixel mode, 4 pixel value = 0, 8 pixle values = 1 */
-#define LCCR0_DIS (1 << 10) /* LCD Disable */
-#define LCCR0_QDM (1 << 11) /* LCD Quick Disable mask */
-#define LCCR0_PDD (0xff << 12) /* Palette DMA request delay */
-#define LCCR0_PDD_S 12
-#define LCCR0_BM (1 << 20) /* Branch mask */
-#define LCCR0_OUM (1 << 21) /* Output FIFO underrun mask */
-
-#define LCCR1_PPL Fld (10, 0) /* Pixels Per Line - 1 */
-#define LCCR1_DisWdth(Pixel) /* Display Width [1..800 pix.] */ \
- (((Pixel) - 1) << FShft (LCCR1_PPL))
-
-#define LCCR1_HSW Fld (6, 10) /* Horizontal Synchronization */
-#define LCCR1_HorSnchWdth(Tpix) /* Horizontal Synchronization */ \
- /* pulse Width [1..64 Tpix] */ \
- (((Tpix) - 1) << FShft (LCCR1_HSW))
-
-#define LCCR1_ELW Fld (8, 16) /* End-of-Line pixel clock Wait */
- /* count - 1 [Tpix] */
-#define LCCR1_EndLnDel(Tpix) /* End-of-Line Delay */ \
- /* [1..256 Tpix] */ \
- (((Tpix) - 1) << FShft (LCCR1_ELW))
-
-#define LCCR1_BLW Fld (8, 24) /* Beginning-of-Line pixel clock */
- /* Wait count - 1 [Tpix] */
-#define LCCR1_BegLnDel(Tpix) /* Beginning-of-Line Delay */ \
- /* [1..256 Tpix] */ \
- (((Tpix) - 1) << FShft (LCCR1_BLW))
-
-
-#define LCCR2_LPP Fld (10, 0) /* Line Per Panel - 1 */
-#define LCCR2_DisHght(Line) /* Display Height [1..1024 lines] */ \
- (((Line) - 1) << FShft (LCCR2_LPP))
-
-#define LCCR2_VSW Fld (6, 10) /* Vertical Synchronization pulse */
- /* Width - 1 [Tln] (L_FCLK) */
-#define LCCR2_VrtSnchWdth(Tln) /* Vertical Synchronization pulse */ \
- /* Width [1..64 Tln] */ \
- (((Tln) - 1) << FShft (LCCR2_VSW))
-
-#define LCCR2_EFW Fld (8, 16) /* End-of-Frame line clock Wait */
- /* count [Tln] */
-#define LCCR2_EndFrmDel(Tln) /* End-of-Frame Delay */ \
- /* [0..255 Tln] */ \
- ((Tln) << FShft (LCCR2_EFW))
-
-#define LCCR2_BFW Fld (8, 24) /* Beginning-of-Frame line clock */
- /* Wait count [Tln] */
-#define LCCR2_BegFrmDel(Tln) /* Beginning-of-Frame Delay */ \
- /* [0..255 Tln] */ \
- ((Tln) << FShft (LCCR2_BFW))
-
-#if 0
-#define LCCR3_PCD (0xff) /* Pixel clock divisor */
-#define LCCR3_ACB (0xff << 8) /* AC Bias pin frequency */
-#define LCCR3_ACB_S 8
-#endif
-
-#define LCCR3_API (0xf << 16) /* AC Bias pin trasitions per interrupt */
-#define LCCR3_API_S 16
-#define LCCR3_VSP (1 << 20) /* vertical sync polarity */
-#define LCCR3_HSP (1 << 21) /* horizontal sync polarity */
-#define LCCR3_PCP (1 << 22) /* pixel clock polarity */
-#define LCCR3_OEP (1 << 23) /* output enable polarity */
-#if 0
-#define LCCR3_BPP (7 << 24) /* bits per pixel */
-#define LCCR3_BPP_S 24
-#endif
-#define LCCR3_DPC (1 << 27) /* double pixel clock mode */
-
-
-#define LCCR3_PCD Fld (8, 0) /* Pixel Clock Divisor */
-#define LCCR3_PixClkDiv(Div) /* Pixel Clock Divisor */ \
- (((Div) << FShft (LCCR3_PCD)))
-
-
-#define LCCR3_BPP Fld (3, 24) /* Bit Per Pixel */
-#define LCCR3_Bpp(Bpp) /* Bit Per Pixel */ \
- (((Bpp) << FShft (LCCR3_BPP)))
-
-#define LCCR3_ACB Fld (8, 8) /* AC Bias */
-#define LCCR3_Acb(Acb) /* BAC Bias */ \
- (((Acb) << FShft (LCCR3_ACB)))
-
-#define LCCR3_HorSnchH (LCCR3_HSP*0) /* Horizontal Synchronization */
- /* pulse active High */
-#define LCCR3_HorSnchL (LCCR3_HSP*1) /* Horizontal Synchronization */
-
-#define LCCR3_VrtSnchH (LCCR3_VSP*0) /* Vertical Synchronization pulse */
- /* active High */
-#define LCCR3_VrtSnchL (LCCR3_VSP*1) /* Vertical Synchronization pulse */
- /* active Low */
-
-#define LCSR_LDD (1 << 0) /* LCD Disable Done */
-#define LCSR_SOF (1 << 1) /* Start of frame */
-#define LCSR_BER (1 << 2) /* Bus error */
-#define LCSR_ABC (1 << 3) /* AC Bias count */
-#define LCSR_IUL (1 << 4) /* input FIFO underrun Lower panel */
-#define LCSR_IUU (1 << 5) /* input FIFO underrun Upper panel */
-#define LCSR_OU (1 << 6) /* output FIFO underrun */
-#define LCSR_QD (1 << 7) /* quick disable */
-#define LCSR_EOF (1 << 8) /* end of frame */
-#define LCSR_BS (1 << 9) /* branch status */
-#define LCSR_SINT (1 << 10) /* subsequent interrupt */
-
-#define LDCMD_PAL (1 << 26) /* instructs DMA to load palette buffer */
-
-#define LCSR_LDD (1 << 0) /* LCD Disable Done */
-#define LCSR_SOF (1 << 1) /* Start of frame */
-#define LCSR_BER (1 << 2) /* Bus error */
-#define LCSR_ABC (1 << 3) /* AC Bias count */
-#define LCSR_IUL (1 << 4) /* input FIFO underrun Lower panel */
-#define LCSR_IUU (1 << 5) /* input FIFO underrun Upper panel */
-#define LCSR_OU (1 << 6) /* output FIFO underrun */
-#define LCSR_QD (1 << 7) /* quick disable */
-#define LCSR_EOF (1 << 8) /* end of frame */
-#define LCSR_BS (1 << 9) /* branch status */
-#define LCSR_SINT (1 << 10) /* subsequent interrupt */
-
-#define LDCMD_PAL (1 << 26) /* instructs DMA to load palette buffer */
-
-/*
- * Memory controller
- */
-
-#define MEMC_BASE __REG(0x48000000) /* Base of Memory Controller */
-#define MDCNFG_OFFSET 0x0
-#define MDREFR_OFFSET 0x4
-#define MSC0_OFFSET 0x8
-#define MSC1_OFFSET 0xC
-#define MSC2_OFFSET 0x10
-#define MECR_OFFSET 0x14
-#define SXLCR_OFFSET 0x18
-#define SXCNFG_OFFSET 0x1C
-#define FLYCNFG_OFFSET 0x20
-#define SXMRS_OFFSET 0x24
-#define MCMEM0_OFFSET 0x28
-#define MCMEM1_OFFSET 0x2C
-#define MCATT0_OFFSET 0x30
-#define MCATT1_OFFSET 0x34
-#define MCIO0_OFFSET 0x38
-#define MCIO1_OFFSET 0x3C
-#define MDMRS_OFFSET 0x40
-
-#define MDCNFG __REG(0x48000000) /* SDRAM Configuration Register 0 */
-#define MDCNFG_DE0 0x00000001
-#define MDCNFG_DE1 0x00000002
-#define MDCNFG_DE2 0x00010000
-#define MDCNFG_DE3 0x00020000
-#define MDCNFG_DWID0 0x00000004
-
-#define MDREFR __REG(0x48000004) /* SDRAM Refresh Control Register */
-#define MSC0 __REG(0x48000008) /* Static Memory Control Register 0 */
-#define MSC1 __REG(0x4800000C) /* Static Memory Control Register 1 */
-#define MSC2 __REG(0x48000010) /* Static Memory Control Register 2 */
-#define MECR __REG(0x48000014) /* Expansion Memory (PCMCIA/Compact Flash) Bus Configuration */
-#define SXLCR __REG(0x48000018) /* LCR value to be written to SDRAM-Timing Synchronous Flash */
-#define SXCNFG __REG(0x4800001C) /* Synchronous Static Memory Control Register */
-#define SXMRS __REG(0x48000024) /* MRS value to be written to Synchronous Flash or SMROM */
-#define MCMEM0 __REG(0x48000028) /* Card interface Common Memory Space Socket 0 Timing */
-#define MCMEM1 __REG(0x4800002C) /* Card interface Common Memory Space Socket 1 Timing */
-#define MCATT0 __REG(0x48000030) /* Card interface Attribute Space Socket 0 Timing Configuration */
-#define MCATT1 __REG(0x48000034) /* Card interface Attribute Space Socket 1 Timing Configuration */
-#define MCIO0 __REG(0x48000038) /* Card interface I/O Space Socket 0 Timing Configuration */
-#define MCIO1 __REG(0x4800003C) /* Card interface I/O Space Socket 1 Timing Configuration */
-#define MDMRS __REG(0x48000040) /* MRS value to be written to SDRAM */
-#define BOOT_DEF __REG(0x48000044) /* Read-Only Boot-Time Register. Contains BOOT_SEL and PKG_SEL */
-
-#define MDREFR_K2FREE (1 << 25) /* SDRAM Free-Running Control */
-#define MDREFR_K1FREE (1 << 24) /* SDRAM Free-Running Control */
-#define MDREFR_K0FREE (1 << 23) /* SDRAM Free-Running Control */
-#define MDREFR_SLFRSH (1 << 22) /* SDRAM Self-Refresh Control/Status */
-#define MDREFR_APD (1 << 20) /* SDRAM/SSRAM Auto-Power-Down Enable */
-#define MDREFR_K2DB2 (1 << 19) /* SDCLK2 Divide by 2 Control/Status */
-#define MDREFR_K2RUN (1 << 18) /* SDCLK2 Run Control/Status */
-#define MDREFR_K1DB2 (1 << 17) /* SDCLK1 Divide by 2 Control/Status */
-#define MDREFR_K1RUN (1 << 16) /* SDCLK1 Run Control/Status */
-#define MDREFR_E1PIN (1 << 15) /* SDCKE1 Level Control/Status */
-#define MDREFR_K0DB2 (1 << 14) /* SDCLK0 Divide by 2 Control/Status */
-#define MDREFR_K0RUN (1 << 13) /* SDCLK0 Run Control/Status */
-#define MDREFR_E0PIN (1 << 12) /* SDCKE0 Level Control/Status */
-
-
-#endif