apalis-tk1: support v1.2 hardware revision
Support the V1.2 hardware revision with the following pin muxing
changes:
Ddc_scl_pv4 and ddc_sda_pv5 previously used as Apalis GPIO3 and GPIO4
are now used as DDC pins.
Gen2_i2c_scl_pt5 and gen2_i2c_sda_pt6 previously used as DDC pins are
now used as USB power enable signals.
Usb_vbus_en0_pn4 and usb_vbus_en1_pn5 previously used as USB power
enable signals are now used as GPIO3 and GPIO4.
Additionally a new device tree file tegra124-apalis-v1.2-eval.dtb is
loaded on V1.2 and later modules and resp. USB power enable signals
activated.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
diff --git a/include/configs/apalis-tk1.h b/include/configs/apalis-tk1.h
index 843e64e..a219750 100644
--- a/include/configs/apalis-tk1.h
+++ b/include/configs/apalis-tk1.h
@@ -18,6 +18,9 @@
#define CONFIG_TEGRA_ENABLE_UARTA
#define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTA_BASE
+#define FDT_MODULE "apalis-v1.2"
+#define FDT_MODULE_V1_0 "apalis"
+
/* Environment in eMMC, before config block at the end of 1st "boot sector" */
#define CONFIG_ENV_OFFSET (-CONFIG_ENV_SIZE + \
CONFIG_TDX_CFG_BLOCK_OFFSET)
@@ -58,7 +61,7 @@
"emmcbootpart=1\0" \
"emmcdev=0\0" \
"emmcdtbload=setenv dtbparam; load mmc ${emmcdev}:${emmcbootpart} " \
- "${fdt_addr_r} ${soc}-apalis-${fdt_board}.dtb && " \
+ "${fdt_addr_r} ${soc}-${fdt_module}-${fdt_board}.dtb && " \
"setenv dtbparam ${fdt_addr_r}\0" \
"emmcfinduuid=part uuid mmc ${mmcdev}:${emmcrootpart} uuid\0" \
"emmcrootpart=2\0"
@@ -70,7 +73,7 @@
"run nfsdtbload; dhcp ${kernel_addr_r} " \
"&& run fdt_fixup && bootz ${kernel_addr_r} - ${dtbparam}\0" \
"nfsdtbload=setenv dtbparam; tftp ${fdt_addr_r} " \
- "${soc}-apalis-${fdt_board}.dtb " \
+ "${soc}-${fdt_module}-${fdt_board}.dtb " \
"&& setenv dtbparam ${fdt_addr_r}\0"
#define SD_BOOTCMD \
@@ -85,7 +88,7 @@
"sdbootpart=1\0" \
"sddev=1\0" \
"sddtbload=setenv dtbparam; load mmc ${sddev}:${sdbootpart} " \
- "${fdt_addr_r} ${soc}-apalis-${fdt_board}.dtb " \
+ "${fdt_addr_r} ${soc}-${fdt_module}-${fdt_board}.dtb " \
"&& setenv dtbparam ${fdt_addr_r}\0" \
"sdfinduuid=part uuid mmc ${sddev}:${sdrootpart} uuid\0" \
"sdrootpart=2\0"
@@ -102,7 +105,7 @@
"usbbootpart=1\0" \
"usbdev=0\0" \
"usbdtbload=setenv dtbparam; load usb ${usbdev}:${usbbootpart} " \
- "${fdt_addr_r} ${soc}-apalis-${fdt_board}.dtb " \
+ "${fdt_addr_r} ${soc}-${fdt_module}-${fdt_board}.dtb " \
"&& setenv dtbparam ${fdt_addr_r}\0" \
"usbfinduuid=part uuid usb ${usbdev}:${usbrootpart} uuid\0" \
"usbrootpart=2\0"
@@ -117,6 +120,7 @@
EMMC_BOOTCMD \
"fdt_board=eval\0" \
"fdt_fixup=;\0" \
+ "fdt_module=" FDT_MODULE "\0" \
NFS_BOOTCMD \
SD_BOOTCMD \
USB_BOOTCMD \