ARM: UniPhier: fix typos in comments
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
diff --git a/arch/arm/mach-uniphier/lowlevel_init.S b/arch/arm/mach-uniphier/lowlevel_init.S
index 3a3ada8..4a23ea4 100644
--- a/arch/arm/mach-uniphier/lowlevel_init.S
+++ b/arch/arm/mach-uniphier/lowlevel_init.S
@@ -25,8 +25,8 @@
* First we need to turn on MMU and Dcache again to get back
* data access to L2.
*/
- mrc p15, 0, r0, c1, c0, 0 @ SCTLR (System Contrl Register)
- orr r0, r0, #(CR_C | CR_M) @ enable MMU and Dcache
+ mrc p15, 0, r0, c1, c0, 0 @ SCTLR (System Control Register)
+ orr r0, r0, #(CR_C | CR_M) @ enable MMU and Dcache
mcr p15, 0, r0, c1, c0, 0
#ifdef CONFIG_DEBUG_LL
@@ -41,7 +41,7 @@
ldr r3, =init_page_table @ page table must be 16KB aligned
/* Disable MMU and Dcache before switching Page Table */
- mrc p15, 0, r0, c1, c0, 0 @ SCTLR (System Contrl Register)
+ mrc p15, 0, r0, c1, c0, 0 @ SCTLR (System Control Register)
bic r0, r0, #(CR_C | CR_M) @ disable MMU and Dcache
mcr p15, 0, r0, c1, c0, 0
@@ -55,7 +55,7 @@
* bit[7] EXCL (Exclusive cache bit)
* bit[6] SMP
* bit[3] Write full line of zeros mode
- * bit[2] L1 Prefetch enable
+ * bit[2] L1 prefetch enable
* bit[1] L2 prefetch enable
* bit[0] FW (Cache and TLB maintenance broadcast)
*/
@@ -81,7 +81,7 @@
ldr r0, =_start @ entry for the secondary CPU
str r0, [r1]
ldr r0, [r1] @ make sure str is complete before sev
- sev @ kick the sedoncary CPU
+ sev @ kick the secondary CPU
mrc p15, 4, r1, c15, c0, 0 @ Configuration Base Address Register
bfc r1, #0, #13 @ clear bit 12-0
mov r0, #-1
@@ -118,7 +118,7 @@
* TLBs was already invalidated in "../start.S"
* So, we don't need to invalidate it here.
*/
- mrc p15, 0, r0, c1, c0, 0 @ SCTLR (System Contrl Register)
+ mrc p15, 0, r0, c1, c0, 0 @ SCTLR (System Control Register)
orr r0, r0, #(CR_C | CR_M) @ MMU and Dcache enable
mcr p15, 0, r0, c1, c0, 0
@@ -155,7 +155,7 @@
ldr r1, = SSCOPPQSEF
ldr r0, [r1]
cmp r0, #0 @ check if the command is successfully set
- bne 0b @ try again if an error occurres
+ bne 0b @ try again if an error occurs
ldr r1, = SSCOLPQS
1:
diff --git a/arch/arm/mach-uniphier/support_card.c b/arch/arm/mach-uniphier/support_card.c
index e7b4158..77cc794 100644
--- a/arch/arm/mach-uniphier/support_card.c
+++ b/arch/arm/mach-uniphier/support_card.c
@@ -1,6 +1,7 @@
/*
- * Copyright (C) 2012-2014 Panasonic Corporation
- * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ * Copyright (C) 2012-2015 Panasonic Corporation
+ * Copyright (C) 2015 Socionext Inc.
+ * Author: Masahiro Yamada <yamada.masahiro@socionext.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
@@ -94,7 +95,7 @@
/*
* After power on, we need to keep the LAN controller in reset state
* for a while. (200 usec)
- * Fortunatelly, enough wait time is already inserted in pll_init()
+ * Fortunately, enough wait time is already inserted in pll_init()
* function. So we do not have to wait here.
*/
support_card_reset_deassert();
@@ -213,11 +214,11 @@
debug("number of flash banks: %d\n", cfi_flash_num_flash_banks);
}
-#else /* ONFIG_SYS_NO_FLASH */
+#else /* CONFIG_SYS_NO_FLASH */
void detect_num_flash_banks(void)
{
};
-#endif /* ONFIG_SYS_NO_FLASH */
+#endif /* CONFIG_SYS_NO_FLASH */
void support_card_late_init(void)
{