Coding style cleanup, update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
diff --git a/CHANGELOG b/CHANGELOG
index 6ebf487..5472c8f 100644
--- a/CHANGELOG
+++ b/CHANGELOG
@@ -1,3 +1,231 @@
+commit 85eb5caf6b906f7ec5b54814e8c7c74f55986bb7
+Author: Wolfgang Denk <wd@denx.de>
+Date: Tue Aug 14 09:47:27 2007 +0200
+
+ Coding style cleanup; rebuild CHANGELOG
+
+commit 7f3f2bd2dc08e0b05e185662ca2e2d283757104a
+Author: Randy Vinson <rvinson@linuxbox.(none)>
+Date: Tue Feb 27 19:42:22 2007 -0700
+
+ 85xxCDS: Add make targets for legacy systems.
+
+ The PCI ID select values on the Arcadia main board differ depending
+ on the version of the hardware. The standard configuration supports
+ Rev 3.1. The legacy target supports Rev 2.x.
+
+ Signed-off-by Randy Vinson <rvinson@mvista.com>
+
+commit e41094c7e38177c755fbd9b182018069614f080d
+Author: Andy Fleming <afleming@freescale.com>
+Date: Tue Aug 14 01:50:09 2007 -0500
+
+ 85xxCDS: Enable the VIA PCI-to-ISA bridge.
+
+ Author: Randy Vinson <rvinson@linuxbox.(none)>
+
+ Enable the PCI-to-ISA bridge in the VIA Southbridge located on the
+ Arcadia main board.
+
+ Signed-off-by: Randy Vinson <rvinson@mvista.com>
+ Signed-off-by: York Sun <yorksun@freescale.com>
+
+commit da9d4610d76e52c4d20a8f3d8433439a7fcf5b71
+Author: Andy Fleming <afleming@freescale.com>
+Date: Tue Aug 14 00:14:25 2007 -0500
+
+ Add support for UEC to 8568
+
+ Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
+ Signed-off-by: Andy Fleming <afleming@freescale.com>
+
+commit c59e4091ffe0148398b9e9ff14a019ea038b7432
+Author: Haiying Wang <Haiying.Wang@freescale.com>
+Date: Tue Jun 19 14:18:34 2007 -0400
+
+ Add PCI support for MPC8568MDS board
+
+ This patch is against u-boot-mpc85xx.git of www.denx.com
+
+ Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
+ Signed-off-by: Ebony Zhu <ebony.zhu@freescale.com>
+
+commit d111d6382c99fdea08c2312eeeae8786945e189a
+Author: Haiying Wang <Haiying.Wang@freescale.com>
+Date: Tue Jun 19 14:18:32 2007 -0400
+
+ Empirically set cpo and clk_adjust for mpc85xx DDR2 support
+
+ This patch is against u-boot-mpc85xx.git of www.denx.com
+
+ Setting cpo to 0x9 for frequencies higher than 333MHz is verified on
+ both MPC8548CDS board and MPC8568MDS board, especially for supporting
+ 533MHz DDR2.
+
+ Setting clk_adjust to 0x6(3/4 late cycle) for MPC8568MDS board is for
+ DDR2 on all current board versions especially ver 1.92 or later to bring
+ up.
+
+ Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
+
+commit 3db0bef59eab1155801618cef5c481e97553b597
+Author: Kumar Gala <galak@kernel.crashing.org>
+Date: Tue Aug 7 18:07:27 2007 -0500
+
+ Use an absolute address when jumping out of 4k boot page
+
+ On e500 when we leave the 4k boot page we should use an absolute address since
+ we don't know where the board code may want us to be really running at.
+
+ Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
+
+commit 39980c610c9a4c381907c9e1d1b9c0e1c0dca57a
+Author: Andy Fleming <afleming@freescale.com>
+Date: Mon Aug 13 14:49:59 2007 -0500
+
+ MPC85xx BA bits not set for 3-bit bank address DIMM
+
+ The current implementation does not set the number of bank address bits
+ (BA) in the processor. The default assumes 2 logical bank bits. This
+ works fine for a DIMM that uses devices with 4 internal banks (SPD
+ byte17 = 0x4) but needs to be set appropriately for a DIMM that uses
+ devices with 8 internal banks (SPD byte17 = 0x8).
+
+ Signed-off-by: Greg Davis <DavisG@embeddedplanet.com>
+
+commit 6c543597bb4b1ecf5d8589f7abb0f39929fb7fd1
+Author: Andy Fleming <afleming@freescale.com>
+Date: Mon Aug 13 14:38:06 2007 -0500
+
+ Fix minor 85xx warnings
+
+ Some patches had inserted warnings into the build:
+ * mpc8560ads declared data without using it
+ * cpu_init declared ecm and immap without using it in all CONFIGs
+ * MPC8548CDS.h had its default filenames changed so that they contained
+ "\m" in the paths. Made the defaults not Windows-specific (or
+ anything-specific)
+
+ Signed-off-by: Andy Fleming <afleming@freescale.com>
+
+commit f2cff6b104f82b993bef6086ce0c97159bbe1add
+Author: Ed Swarthout <Ed.Swarthout@freescale.com>
+Date: Fri Jul 27 01:50:52 2007 -0500
+
+ 8548cds PCIE support.
+
+ Make the early L1 cache stack region guarded to prevent speculative
+ fetches outside the locked range.
+
+ Use _PHYS defines, not _MEM for cpu-side PCI memory mapped regions.
+ init.S whitespace cleanup.
+
+ Allow TEXT_BASE value to be specified on command line. This allows it
+ to be set to 0xfffc0000 which cuts the uboot binary in half.
+
+ Clear and enable lbc and ecm errors.
+
+ Update last_busno in device-tree for pci and pcie.
+
+ Remove load of obsolete cpu/mpc85xx/pci.0
+
+ Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
+ Acked-by: Andy Fleming <afleming@freescale.com>
+
+commit 837f1ba05cfb248aba5ab8e1fb1bfeefa07d5962
+Author: Ed Swarthout <Ed.Swarthout@freescale.com>
+Date: Fri Jul 27 01:50:51 2007 -0500
+
+ 8544ds PCIE support
+
+ PCI1 LAW mapping should use CFG_PCI1_MEM_PHY and not _BASE address.
+
+ Enable LBC and ECM errors and clear error registers.
+
+ Add tftpflash env var to get uboot from tftp server and flash it.
+
+ Add pci/pcie convenience env vars to display register space:
+ "run pcie3regs" to see all pcie3 ccsr registers
+ "run pcie3cfg" to see all cfg registers
+ Whitespace cleanup and MPC8544DS.h
+
+ Enable CONFIG_INTERRUPTS.
+
+ Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
+ Acked-by: Andy Fleming <afleming@freescale.com>
+
+commit 61a21e980a7b9188424d04f1c265fdc5c21c7e85
+Author: Andy Fleming <afleming@freescale.com>
+Date: Tue Aug 14 01:34:21 2007 -0500
+
+ 85xx start.S cleanup and exception support
+
+ From: Ed Swarthout <Ed.Swarthout@freescale.com>
+
+ Support external interrupts from platform to eliminate system hangs.
+ Define CONFIG_INTERRUPTS board configure option to enable.
+ Enable ecm, ddr, lbc, and pci/pcie error interrupts in PIC.
+
+ Remove extra cpu initialization redundant with hardware initialization.
+ Whitespace cleanup.
+
+ Define and use _START_OFFSET consistent with other processors using
+ ppc_asm.tmpl
+
+ Move additional code from .text to boot page to make room for
+ exception vectors at start of image.
+
+ Handle Machine Check, External and Critical exceptions.
+
+ Fix e500 machine check error determination in traps.c
+
+ TEXT_BASE can now be 0xfffc_0000 - which cuts binary image in half.
+
+ Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
+ Acked-by: Andy Fleming <afleming@freescale.com>
+
+commit 7bd30fc4a6475b41d6679ae3aafc9fa505260c47
+Author: Andy Fleming <afleming@freescale.com>
+Date: Tue Aug 14 01:33:18 2007 -0500
+
+ Add MPC8544DS README
+
+ Signed-off-by: Andy Fleming <afleming@freescale.com>
+
+commit 40c7f9b0de4e300370adfc704128fa0f79a143b6
+Author: Ed Swarthout <Ed.Swarthout@freescale.com>
+Date: Fri Jul 27 01:50:48 2007 -0500
+
+ 85xx allow debugger to configure ddr.
+
+ Only check for mpc8548 rev 1 when compiled for 8548.
+
+ Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
+ Acked-by: Andy Fleming <afleming@freescale.com>
+
+commit 29372ff38c5baab7d0e3a8c14fe11fa194a38704
+Author: Ed Swarthout <Ed.Swarthout@freescale.com>
+Date: Fri Jul 27 01:50:47 2007 -0500
+
+ mpc85xx L2 cache reporting and SRAM relocation option.
+
+ Allow debugger to override flash cs0/cs1 settings to enable alternate
+ boot regions
+
+ Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
+ Acked-by: Andy Fleming <afleming@freescale.com>
+
+commit 41f0f8fb1ab92f0cba7d329de90070f822f8299f
+Author: Ed Swarthout <Ed.Swarthout@freescale.com>
+Date: Fri Jul 27 01:50:46 2007 -0500
+
+ e500 needs ppc_asm.tmp MCK_EXCEPTION
+
+ Always define MCK_EXCEPTION macro - so e500 can use it too.
+
+ Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
+ Acked-by: Andy Fleming <afleming@freescale.com>
+
commit 53a5c424bf8655b7b4e2c305a441963259a26a81
Author: David Updegraff <dave@cray.com>
Date: Mon Jun 11 10:41:07 2007 -0500
diff --git a/doc/README.mpc8544ds b/doc/README.mpc8544ds
index 14c7f76..bf257a0 100644
--- a/doc/README.mpc8544ds
+++ b/doc/README.mpc8544ds
@@ -98,7 +98,7 @@
linux-2.6/arch/powerpc/boot/dts/mpc8544ds.dts
-After placing the DTB file in your TFTP disk area,
+After placing the DTB file in your TFTP disk area,
you can download that dtb file using a command like:
tftp 900000 mpc8544ds.dtb