arm64: zynqmp: Remove additional comments from dts files
Remove additional comments which were removed as the part of upstreaming.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
diff --git a/arch/arm/dts/zynqmp-zc1751-xm015-dc1.dts b/arch/arm/dts/zynqmp-zc1751-xm015-dc1.dts
index 0ddb43d..3c20547 100644
--- a/arch/arm/dts/zynqmp-zc1751-xm015-dc1.dts
+++ b/arch/arm/dts/zynqmp-zc1751-xm015-dc1.dts
@@ -39,7 +39,6 @@
};
};
-/* fpd_dma clk 667MHz, lpd_dma 500MHz */
&fpd_dma_chan1 {
status = "okay";
};
diff --git a/arch/arm/dts/zynqmp-zc1751-xm016-dc2.dts b/arch/arm/dts/zynqmp-zc1751-xm016-dc2.dts
index 670cc44..22a3c1e 100644
--- a/arch/arm/dts/zynqmp-zc1751-xm016-dc2.dts
+++ b/arch/arm/dts/zynqmp-zc1751-xm016-dc2.dts
@@ -49,7 +49,6 @@
status = "okay";
};
-/* fpd_dma clk 667MHz, lpd_dma 500MHz */
&fpd_dma_chan1 {
status = "okay";
};
diff --git a/arch/arm/dts/zynqmp-zc1751-xm018-dc4.dts b/arch/arm/dts/zynqmp-zc1751-xm018-dc4.dts
index 41012fa..fb49b4f 100644
--- a/arch/arm/dts/zynqmp-zc1751-xm018-dc4.dts
+++ b/arch/arm/dts/zynqmp-zc1751-xm018-dc4.dts
@@ -51,7 +51,6 @@
status = "okay";
};
-/* fpd_dma clk 667MHz, lpd_dma 500MHz */
&fpd_dma_chan1 {
status = "okay";
};
diff --git a/arch/arm/dts/zynqmp-zc1751-xm019-dc5.dts b/arch/arm/dts/zynqmp-zc1751-xm019-dc5.dts
index 99aa74e..fe737be 100644
--- a/arch/arm/dts/zynqmp-zc1751-xm019-dc5.dts
+++ b/arch/arm/dts/zynqmp-zc1751-xm019-dc5.dts
@@ -37,7 +37,6 @@
};
};
-/* fpd_dma clk 667MHz, lpd_dma 500MHz */
&fpd_dma_chan1 {
status = "okay";
};
@@ -83,12 +82,10 @@
status = "okay";
};
-/* FIXME: Add device */
&i2c0 {
status = "okay";
};
-/* FIXME: Add device */
&i2c1 {
status = "okay";
};
diff --git a/arch/arm/dts/zynqmp-zcu102-revA.dts b/arch/arm/dts/zynqmp-zcu102-revA.dts
index c9cffc1..efa94a1 100644
--- a/arch/arm/dts/zynqmp-zcu102-revA.dts
+++ b/arch/arm/dts/zynqmp-zcu102-revA.dts
@@ -77,7 +77,6 @@
status = "okay";
};
-/* fpd_dma clk 667MHz, lpd_dma 500MHz */
&fpd_dma_chan1 {
status = "okay";
};
@@ -381,23 +380,17 @@
reg = <0x20>;
};
-/* drivers/hwmon/pmbus/Kconfig:86: be called max20751.
-drivers/hwmon/pmbus/Makefile:11:obj-$(CONFIG_SENSORS_MAX20751) += max20751.o
-*/
- max20751@72 { /* u95 FIXME - not detected */
+ max20751@72 { /* u95 */
compatible = "maxim,max20751";
reg = <0x72>;
};
- max20751@73 { /* u96 FIXME - not detected */
+ max20751@73 { /* u96 */
compatible = "maxim,max20751";
reg = <0x73>;
};
};
/* Bus 3 is not connected */
};
-
- /* FIXME PMOD - j160 */
- /* FIXME MSP430F - u41 - not detected */
};
&i2c1 {
@@ -409,8 +402,7 @@
scl-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
sda-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
- /* FIXME PL i2c via PCA9306 - u45 */
- /* FIXME MSP430 - u41 - not detected */
+ /* PL i2c via PCA9306 - u45 */
i2c-mux@74 { /* u34 */
compatible = "nxp,pca9548";
#address-cells = <1>;
@@ -515,24 +507,19 @@
#size-cells = <0>;
reg = <3>;
/* DDR4 SODIMM */
- dev@19 { /* u-boot detection */
- compatible = "xxx";
+ dev@19 {
reg = <0x19>;
};
- dev@30 { /* u-boot detection */
- compatible = "xxx";
+ dev@30 {
reg = <0x30>;
};
- dev@35 { /* u-boot detection */
- compatible = "xxx";
+ dev@35 {
reg = <0x35>;
};
- dev@36 { /* u-boot detection */
- compatible = "xxx";
+ dev@36 {
reg = <0x36>;
};
- dev@51 { /* u-boot detection - maybe SPD */
- compatible = "xxx";
+ dev@51 {
reg = <0x51>;
};
};
diff --git a/arch/arm/dts/zynqmp-zcu102-revB.dts b/arch/arm/dts/zynqmp-zcu102-revB.dts
index 384d0a2..af4d868 100644
--- a/arch/arm/dts/zynqmp-zcu102-revB.dts
+++ b/arch/arm/dts/zynqmp-zcu102-revB.dts
@@ -26,8 +26,6 @@
/delete-node/ phy@21;
};
-/* Different qspi 512Mbit version */
-
/* Fix collision with u61 */
&i2c0 {
i2c-mux@75 {