x86: gpio: add pinctrl support from the device tree

Every pin can be configured now from the device tree. A dt-bindings
has been added to describe the different property available.

Change-Id: I1668886062655f83700d0e7bbbe3ad09b19ee975
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Acked-by: Simon Glass <sjg@chromium.org>
diff --git a/arch/x86/dts/minnowmax.dts b/arch/x86/dts/minnowmax.dts
index 7103bc5..bd21bfb 100644
--- a/arch/x86/dts/minnowmax.dts
+++ b/arch/x86/dts/minnowmax.dts
@@ -6,6 +6,8 @@
 
 /dts-v1/;
 
+#include <dt-bindings/gpio/x86-gpio.h>
+
 /include/ "skeleton.dtsi"
 /include/ "serial.dtsi"
 
@@ -22,6 +24,27 @@
 		silent_console = <0>;
 	};
 
+	pch_pinctrl {
+		compatible = "intel,x86-pinctrl";
+		io-base = <0x4c>;
+
+		pin_usb_host_en0@0 {
+			gpio-offset = <0x80 8>;
+			pad-offset = <0x260>;
+			mode-gpio;
+			output-value = <1>;
+			direction = <PIN_OUTPUT>;
+		};
+
+		pin_usb_host_en1@0 {
+			gpio-offset = <0x80 9>;
+			pad-offset = <0x258>;
+			mode-gpio;
+			output-value = <1>;
+			direction = <PIN_OUTPUT>;
+		};
+	};
+
 	gpioa {
 		compatible = "intel,ich6-gpio";
 		u-boot,dm-pre-reloc;
diff --git a/arch/x86/include/asm/gpio.h b/arch/x86/include/asm/gpio.h
index 1099427..ed85b08 100644
--- a/arch/x86/include/asm/gpio.h
+++ b/arch/x86/include/asm/gpio.h
@@ -147,6 +147,7 @@
 	} set3;
 };
 
+int gpio_ich6_pinctrl_init(void);
 void setup_pch_gpios(u16 gpiobase, const struct pch_gpio_map *gpio);
 void ich_gpio_set_gpio_map(const struct pch_gpio_map *map);
 
diff --git a/doc/device-tree-bindings/gpio/intel,x86-pinctrl.txt b/doc/device-tree-bindings/gpio/intel,x86-pinctrl.txt
new file mode 100644
index 0000000..45ab1af
--- /dev/null
+++ b/doc/device-tree-bindings/gpio/intel,x86-pinctrl.txt
@@ -0,0 +1,31 @@
+Intel x86 PINCTRL/GPIO controller
+
+Pin-muxing on x86 can be described with a node for the PINCTRL master
+node and a set of child nodes for each pin on the SoC.
+
+The PINCTRL master node requires the following properties:
+- compatible : "intel,x86-pinctrl"
+
+Pin nodes must be children of the pinctrl master node and can
+contain the following properties:
+- pad-offset        - (required) offset in the IOBASE for the pin to configured.
+- gpio-offset       - (required) offset in the GPIOBASE for the pin to configured and
+					also the bit shift in this register.
+- mode-gpio			- (optional) standalone property to force the pin into GPIO mode.
+- mode-func			- (optional) function number to assign to the pin. if 'mode-gpio'
+					is set, this property will be ignored.
+in case of 'mode-gpio' property set:
+- output-value		- (optional) this set the default output value of the GPIO.
+- direction         - (optional) this set the direction of the gpio.
+- pull-str          - (optional) this set the pull strength of the pin.
+- pull-assign       - (optional) this set the pull assignement (up/down) of the pin.
+
+Example:
+
+pin_usb_host_en0@0 {
+    gpio-offset = <0x80 8>;
+    pad-offset = <0x260>;
+    mode-gpio;
+    output-value = <1>;
+    direction = <PIN_OUTPUT>;
+};
diff --git a/drivers/gpio/intel_ich6_gpio.c b/drivers/gpio/intel_ich6_gpio.c
index 7e679a0..8a108f3 100644
--- a/drivers/gpio/intel_ich6_gpio.c
+++ b/drivers/gpio/intel_ich6_gpio.c
@@ -44,21 +44,28 @@
 	uint16_t lvl;
 };
 
+#define GPIO_USESEL_OFFSET(x)	(x)
+#define GPIO_IOSEL_OFFSET(x)	(x + 4)
+#define GPIO_LVL_OFFSET(x)	(x + 8)
+
+#define IOPAD_MODE_MASK				0x7
+#define IOPAD_PULL_ASSIGN_SHIFT		7
+#define IOPAD_PULL_ASSIGN_MASK		(0x3 << IOPAD_PULL_ASSIGN_SHIFT)
+#define IOPAD_PULL_STRENGTH_SHIFT	9
+#define IOPAD_PULL_STRENGTH_MASK	(0x3 << IOPAD_PULL_STRENGTH_SHIFT)
+
 /* TODO: Move this to device tree, or platform data */
 void ich_gpio_set_gpio_map(const struct pch_gpio_map *map)
 {
 	gd->arch.gpio_map = map;
 }
 
-static int gpio_ich6_ofdata_to_platdata(struct udevice *dev)
+static int gpio_ich6_get_base(unsigned long base)
 {
-	struct ich6_bank_platdata *plat = dev_get_platdata(dev);
 	pci_dev_t pci_dev;			/* handle for 0:1f:0 */
 	u8 tmpbyte;
 	u16 tmpword;
 	u32 tmplong;
-	u16 gpiobase;
-	int offset;
 
 	/* Where should it be? */
 	pci_dev = PCI_BDF(0, 0x1f, 0);
@@ -123,9 +130,9 @@
 	 * while on the Ivybridge the bit0 is used to indicate it is an
 	 * I/O space.
 	 */
-	tmplong = x86_pci_read_config32(pci_dev, PCI_CFG_GPIOBASE);
+	tmplong = x86_pci_read_config32(pci_dev, base);
 	if (tmplong == 0x00000000 || tmplong == 0xffffffff) {
-		debug("%s: unexpected GPIOBASE value\n", __func__);
+		debug("%s: unexpected BASE value\n", __func__);
 		return -ENODEV;
 	}
 
@@ -135,7 +142,215 @@
 	 * at the offset that we just read. Bit 0 indicates that it's
 	 * an I/O address, not a memory address, so mask that off.
 	 */
-	gpiobase = tmplong & 0xfffe;
+	return tmplong & 0xfffc;
+}
+
+static int _ich6_gpio_set_value(uint16_t base, unsigned offset, int value)
+{
+	u32 val;
+
+	val = inl(base);
+	if (value)
+		val |= (1UL << offset);
+	else
+		val &= ~(1UL << offset);
+	outl(val, base);
+
+	return 0;
+}
+
+static int _ich6_gpio_set_function(uint16_t base, unsigned offset, int func)
+{
+	u32 val;
+
+	if (func) {
+		val = inl(base);
+		val |= (1UL << offset);
+		outl(val, base);
+	} else {
+		val = inl(base);
+		val &= ~(1UL << offset);
+		outl(val, base);
+	}
+
+	return 0;
+}
+
+static int _ich6_gpio_set_direction(uint16_t base, unsigned offset, int dir)
+{
+	u32 val;
+
+	if (!dir) {
+		val = inl(base);
+		val |= (1UL << offset);
+		outl(val, base);
+	} else {
+		val = inl(base);
+		val &= ~(1UL << offset);
+		outl(val, base);
+	}
+
+	return 0;
+}
+
+static int _gpio_ich6_pinctrl_cfg_pin(s32 gpiobase, s32 iobase, int pin_node)
+{
+	u32 gpio_offset[2];
+	int pad_offset;
+	int val;
+	int ret;
+	const void *prop;
+
+	/*
+	 * GPIO node is not mandatory, so we only do the
+	 * pinmuxing if the node exist.
+	 */
+	ret = fdtdec_get_int_array(gd->fdt_blob, pin_node, "gpio-offset",
+			     gpio_offset, 2);
+	if (!ret) {
+		/* Do we want to force the GPIO mode? */
+		prop = fdt_getprop(gd->fdt_blob, pin_node, "mode-gpio",
+				      NULL);
+		if (prop)
+			_ich6_gpio_set_function(GPIO_USESEL_OFFSET
+						(gpiobase) +
+						gpio_offset[0],
+						gpio_offset[1], 1);
+
+		val =
+		    fdtdec_get_int(gd->fdt_blob, pin_node, "direction", -1);
+		if (val != -1)
+			_ich6_gpio_set_direction(GPIO_IOSEL_OFFSET
+						 (gpiobase) +
+						 gpio_offset[0],
+						 gpio_offset[1], val);
+
+		val =
+		    fdtdec_get_int(gd->fdt_blob, pin_node, "output-value", -1);
+		if (val != -1)
+			_ich6_gpio_set_value(GPIO_LVL_OFFSET(gpiobase)
+					     + gpio_offset[0],
+					     gpio_offset[1], val);
+	}
+
+	/* if iobase is present, let's configure the pad */
+	if (iobase != -1) {
+		int iobase_addr;
+
+		/*
+		 * The offset for the same pin for the IOBASE and GPIOBASE are
+		 * different, so instead of maintaining a lookup table,
+		 * the device tree should provide directly the correct
+		 * value for both mapping.
+		 */
+		pad_offset =
+		    fdtdec_get_int(gd->fdt_blob, pin_node, "pad-offset", -1);
+		if (pad_offset == -1) {
+			debug("%s: Invalid register io offset %d\n",
+			      __func__, pad_offset);
+			return -EINVAL;
+		}
+
+		/* compute the absolute pad address */
+		iobase_addr = iobase + pad_offset;
+
+		/*
+		 * Do we need to set a specific function mode?
+		 * If someone put also 'mode-gpio', this option will
+		 * be just ignored by the controller
+		 */
+		val = fdtdec_get_int(gd->fdt_blob, pin_node, "mode-func", -1);
+		if (val != -1)
+			clrsetbits_le32(iobase_addr, IOPAD_MODE_MASK, val);
+
+		/* Configure the pull-up/down if needed */
+		val = fdtdec_get_int(gd->fdt_blob, pin_node, "pull-assign", -1);
+		if (val != -1)
+			clrsetbits_le32(iobase_addr,
+					IOPAD_PULL_ASSIGN_MASK,
+					val << IOPAD_PULL_ASSIGN_SHIFT);
+
+		val =
+		    fdtdec_get_int(gd->fdt_blob, pin_node, "pull-strength", -1);
+		if (val != -1)
+			clrsetbits_le32(iobase_addr,
+					IOPAD_PULL_STRENGTH_MASK,
+					val << IOPAD_PULL_STRENGTH_SHIFT);
+
+		debug("%s: pad cfg [0x%x]: %08x\n", __func__, pad_offset,
+		      readl(iobase_addr));
+	}
+
+	return 0;
+}
+
+int gpio_ich6_pinctrl_init(void)
+{
+	int pin_node;
+	int node;
+	int ret;
+	int gpiobase;
+	int iobase_offset;
+	int iobase = -1;
+
+	/*
+	 * Get the memory/io base address to configure every pins.
+	 * IOBASE is used to configure the mode/pads
+	 * GPIOBASE is used to configure the direction and default value
+	 */
+	gpiobase = gpio_ich6_get_base(PCI_CFG_GPIOBASE);
+	if (gpiobase < 0) {
+		debug("%s: invalid GPIOBASE address (%08x)\n", __func__,
+		      gpiobase);
+		return -EINVAL;
+	}
+
+	/* This is not an error to not have a pinctrl node */
+	node =
+	    fdtdec_next_compatible(gd->fdt_blob, 0, COMPAT_INTEL_X86_PINCTRL);
+	if (node <= 0) {
+		debug("%s: no pinctrl node\n", __func__);
+		return 0;
+	}
+
+	/*
+	 * Get the IOBASE, this is not mandatory as this is not
+	 * supported by all the CPU
+	 */
+	iobase_offset = fdtdec_get_int(gd->fdt_blob, node, "io-base", -1);
+	if (iobase_offset == -1) {
+		debug("%s: io-base offset not present\n", __func__);
+	} else {
+		iobase = gpio_ich6_get_base(iobase_offset);
+		if (iobase < 0) {
+			debug("%s: invalid IOBASE address (%08x)\n", __func__,
+			      iobase);
+			return -EINVAL;
+		}
+	}
+
+	for (pin_node = fdt_first_subnode(gd->fdt_blob, node);
+	     pin_node > 0;
+	     pin_node = fdt_next_subnode(gd->fdt_blob, pin_node)) {
+		/* Configure the pin */
+		ret = _gpio_ich6_pinctrl_cfg_pin(gpiobase, iobase, pin_node);
+		if (ret != 0) {
+			debug("%s: invalid configuration for the pin %d\n",
+			      __func__, pin_node);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static int gpio_ich6_ofdata_to_platdata(struct udevice *dev)
+{
+	struct ich6_bank_platdata *plat = dev_get_platdata(dev);
+	u16 gpiobase;
+	int offset;
+
+	gpiobase = gpio_ich6_get_base(PCI_CFG_GPIOBASE);
 	offset = fdtdec_get_int(gd->fdt_blob, dev->of_offset, "reg", -1);
 	if (offset == -1) {
 		debug("%s: Invalid register offset %d\n", __func__, offset);
@@ -192,30 +407,24 @@
 static int ich6_gpio_direction_input(struct udevice *dev, unsigned offset)
 {
 	struct ich6_bank_priv *bank = dev_get_priv(dev);
-	u32 tmplong;
 
-	tmplong = inl(bank->io_sel);
-	tmplong |= (1UL << offset);
-	outl(bank->io_sel, tmplong);
-	return 0;
+	return _ich6_gpio_set_direction(inl(bank->io_sel), offset, 0);
 }
 
 static int ich6_gpio_direction_output(struct udevice *dev, unsigned offset,
 				       int value)
 {
+	int ret;
 	struct ich6_bank_priv *bank = dev_get_priv(dev);
-	u32 tmplong;
 
-	gpio_set_value(offset, value);
+	ret = _ich6_gpio_set_direction(inl(bank->io_sel), offset, 1);
+	if (ret)
+		return ret;
 
-	tmplong = inl(bank->io_sel);
-	tmplong &= ~(1UL << offset);
-	outl(bank->io_sel, tmplong);
-	return 0;
+	return _ich6_gpio_set_value(bank->lvl, offset, value);
 }
 
 static int ich6_gpio_get_value(struct udevice *dev, unsigned offset)
-
 {
 	struct ich6_bank_priv *bank = dev_get_priv(dev);
 	u32 tmplong;
@@ -230,15 +439,7 @@
 			       int value)
 {
 	struct ich6_bank_priv *bank = dev_get_priv(dev);
-	u32 tmplong;
-
-	tmplong = inl(bank->lvl);
-	if (value)
-		tmplong |= (1UL << offset);
-	else
-		tmplong &= ~(1UL << offset);
-	outl(bank->lvl, tmplong);
-	return 0;
+	return _ich6_gpio_set_value(bank->lvl, offset, value);
 }
 
 static int ich6_gpio_get_function(struct udevice *dev, unsigned offset)
diff --git a/include/dt-bindings/gpio/x86-gpio.h b/include/dt-bindings/gpio/x86-gpio.h
new file mode 100644
index 0000000..7f1de30
--- /dev/null
+++ b/include/dt-bindings/gpio/x86-gpio.h
@@ -0,0 +1,31 @@
+/*
+ * This header provides constants for binding intel,x86-pinctrl.
+ */
+
+#ifndef _DT_BINDINGS_GPIO_X86_GPIO_H
+#define _DT_BINDINGS_GPIO_X86_GPIO_H
+
+#include <dt-bindings/gpio/gpio.h>
+
+#define GPIO_MODE_NATIVE	0
+#define GPIO_MODE_GPIO		1
+
+#define GPIO_MODE_FUNC0	0
+#define GPIO_MODE_FUNC1	1
+#define GPIO_MODE_FUNC2	2
+#define GPIO_MODE_FUNC3	3
+#define GPIO_MODE_FUNC4	4
+#define GPIO_MODE_FUNC5	5
+#define GPIO_MODE_FUNC6	6
+
+#define PIN_INPUT	0
+#define PIN_OUTPUT	1
+
+#define PIN_INPUT_NOPULL	0
+#define PIN_INPUT_PULLUP	1
+#define PIN_INPUT_PULLDOWN	2
+
+#define PULL_STR_2K		0
+#define PULL_STR_20K	2
+
+#endif
diff --git a/include/fdtdec.h b/include/fdtdec.h
index 64c7fa1..4fb8a2a 100644
--- a/include/fdtdec.h
+++ b/include/fdtdec.h
@@ -176,6 +176,7 @@
 	COMPAT_AMS_AS3722,		/* AMS AS3722 PMIC */
 	COMPAT_INTEL_ICH_SPI,		/* Intel ICH7/9 SPI controller */
 	COMPAT_INTEL_QRK_MRC,		/* Intel Quark MRC */
+	COMPAT_INTEL_X86_PINCTRL,	/* Intel ICH7/9 pin control */
 	COMPAT_SOCIONEXT_XHCI,		/* Socionext UniPhier xHCI */
 	COMPAT_INTEL_PCH,		/* Intel PCH */
 	COMPAT_INTEL_IRQ_ROUTER,	/* Intel Interrupt Router */
diff --git a/lib/fdtdec.c b/lib/fdtdec.c
index 1808350..46dfcb6 100644
--- a/lib/fdtdec.c
+++ b/lib/fdtdec.c
@@ -75,6 +75,7 @@
 	COMPAT(AMS_AS3722, "ams,as3722"),
 	COMPAT(INTEL_ICH_SPI, "intel,ich-spi"),
 	COMPAT(INTEL_QRK_MRC, "intel,quark-mrc"),
+	COMPAT(INTEL_X86_PINCTRL, "intel,x86-pinctrl"),
 	COMPAT(SOCIONEXT_XHCI, "socionext,uniphier-xhci"),
 	COMPAT(COMPAT_INTEL_PCH, "intel,bd82x6x"),
 	COMPAT(COMPAT_INTEL_IRQ_ROUTER, "intel,irq-router"),