Squashed 'dts/upstream/' content from commit aaba2d45dc2a
git-subtree-dir: dts/upstream
git-subtree-split: aaba2d45dc2a1b3bbb710f2a3808ee1c9f340abe
diff --git a/Bindings/pci/faraday,ftpci100.yaml b/Bindings/pci/faraday,ftpci100.yaml
new file mode 100644
index 0000000..92efbf0
--- /dev/null
+++ b/Bindings/pci/faraday,ftpci100.yaml
@@ -0,0 +1,174 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/faraday,ftpci100.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Faraday Technology FTPCI100 PCI Host Bridge
+
+maintainers:
+ - Linus Walleij <linus.walleij@linaro.org>
+
+description: |
+ This PCI bridge is found inside that Cortina Systems Gemini SoC platform and
+ is a generic IP block from Faraday Technology. It exists in two variants:
+ plain and dual PCI. The plain version embeds a cascading interrupt controller
+ into the host bridge. The dual version routes the interrupts to the host
+ chips interrupt controller.
+ The host controller appear on the PCI bus with vendor ID 0x159b (Faraday
+ Technology) and product ID 0x4321.
+ I/O space considerations:
+ The plain variant has 128MiB of non-prefetchable memory space, whereas the
+ "dual" variant has 64MiB. Take this into account when describing the ranges.
+
+ Interrupt map considerations:
+
+ The "dual" variant will get INT A, B, C, D from the system interrupt controller
+ and should point to respective interrupt in that controller in its interrupt-map.
+
+ The code which is the only documentation of how the Faraday PCI (the non-dual
+ variant) interrupts assigns the default interrupt mapping/swizzling has
+ typically been like this, doing the swizzling on the interrupt controller side
+ rather than in the interconnect:
+
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map =
+ <0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
+ <0x4800 0 0 2 &pci_intc 1>,
+ <0x4800 0 0 3 &pci_intc 2>,
+ <0x4800 0 0 4 &pci_intc 3>,
+ <0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
+ <0x5000 0 0 2 &pci_intc 2>,
+ <0x5000 0 0 3 &pci_intc 3>,
+ <0x5000 0 0 4 &pci_intc 0>,
+ <0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
+ <0x5800 0 0 2 &pci_intc 3>,
+ <0x5800 0 0 3 &pci_intc 0>,
+ <0x5800 0 0 4 &pci_intc 1>,
+ <0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
+ <0x6000 0 0 2 &pci_intc 0>,
+ <0x6000 0 0 3 &pci_intc 1>,
+ <0x6000 0 0 4 &pci_intc 2>;
+
+allOf:
+ - $ref: /schemas/pci/pci-bus.yaml#
+
+properties:
+ compatible:
+ oneOf:
+ - items:
+ - const: cortina,gemini-pci
+ - const: faraday,ftpci100
+ - items:
+ - const: cortina,gemini-pci-dual
+ - const: faraday,ftpci100-dual
+ - const: faraday,ftpci100
+ - const: faraday,ftpci100-dual
+
+ reg:
+ maxItems: 1
+
+ "#address-cells":
+ const: 3
+
+ "#interrupt-cells":
+ const: 1
+
+ ranges:
+ minItems: 2
+
+ dma-ranges:
+ minItems: 3
+ description: |
+ three ranges for the inbound memory region. The ranges must
+ be aligned to a 1MB boundary, and may be 1MB, 2MB, 4MB, 8MB, 16MB, 32MB, 64MB,
+ 128MB, 256MB, 512MB, 1GB or 2GB in size. The memory should be marked as
+ pre-fetchable.
+
+ clocks:
+ items:
+ - description: peripheral clock (PCLK)
+ - description: PCI clock (PCICLK).
+ description: |
+ If these are not present, they are assumed to be
+ hard-wired enabled and always on. The PCI clock will be 33 or 66 MHz.
+
+ clock-names:
+ items:
+ - const: PCLK
+ - const: PCICLK
+
+ interrupt-controller:
+ type: object
+
+required:
+ - reg
+ - compatible
+ - "#interrupt-cells"
+ - interrupt-map-mask
+ - interrupt-map
+ - dma-ranges
+
+if:
+ properties:
+ compatible:
+ contains:
+ const: faraday,ftpci100
+then:
+ required:
+ - interrupt-controller
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ pci@50000000 {
+ compatible = "cortina,gemini-pci", "faraday,ftpci100";
+ reg = <0x50000000 0x100>;
+ device_type = "pci";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+
+ bus-range = <0x00 0xff>;
+ ranges = /* 1MiB I/O space 0x50000000-0x500fffff */
+ <0x01000000 0 0 0x50000000 0 0x00100000>,
+ /* 128MiB non-prefetchable memory 0x58000000-0x5fffffff */
+ <0x02000000 0 0x58000000 0x58000000 0 0x08000000>;
+
+ /* DMA ranges */
+ dma-ranges =
+ /* 128MiB at 0x00000000-0x07ffffff */
+ <0x02000000 0 0x00000000 0x00000000 0 0x08000000>,
+ /* 64MiB at 0x00000000-0x03ffffff */
+ <0x02000000 0 0x00000000 0x00000000 0 0x04000000>,
+ /* 64MiB at 0x00000000-0x03ffffff */
+ <0x02000000 0 0x00000000 0x00000000 0 0x04000000>;
+
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map =
+ <0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
+ <0x4800 0 0 2 &pci_intc 1>,
+ <0x4800 0 0 3 &pci_intc 2>,
+ <0x4800 0 0 4 &pci_intc 3>,
+ <0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
+ <0x5000 0 0 2 &pci_intc 2>,
+ <0x5000 0 0 3 &pci_intc 3>,
+ <0x5000 0 0 4 &pci_intc 0>,
+ <0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
+ <0x5800 0 0 2 &pci_intc 3>,
+ <0x5800 0 0 3 &pci_intc 0>,
+ <0x5800 0 0 4 &pci_intc 1>,
+ <0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
+ <0x6000 0 0 2 &pci_intc 0>,
+ <0x6000 0 0 3 &pci_intc 0>,
+ <0x6000 0 0 4 &pci_intc 0>;
+ pci_intc: interrupt-controller {
+ interrupt-parent = <&intcon>;
+ interrupt-controller;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ };
+ };