src/arm/st/ste-ux500-samsung-codina-tmo.dts - platform/external/u-boot - Gitiles

 // SPDX-License-Identifier: GPL-2.0-only
 /*
  * Devicetree for the Samsung Galaxy Exhibit SGH-T599 also known as Codina-TMO,
  * the "TMO" shall be read "T-Mobile" as this phone was produced exlusively
  * for T-Mobile in the United States.
  *
  * This phone is closely related to the Codina, but has:
  * - No CPU speed cap, full ~1GHz rate
  * - Different power management IC, AB8505
  * - As AB8505 has a micro USB phy, no TI TSU6111
  * - Different power routing such as the removal of the external LDO for the
  *   touchscreen in favor of using the AB8505
  * - Using a regulator for the key backlight LED
  * - Using the Samsung S6D27A1 panel by default
  * - The panel is using one of the ordinary AB8505 regulators for 1.8V
  * - WiFi/Bluetooth combi chip upgraded to BCM4334
  * - GPIO for backlight control moved from 68 to 69
  */

 /dts-v1/;
 #include "ste-db8500.dtsi"
 #include "ste-ab8505.dtsi"
 #include "ste-dbx5x0-pinctrl.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/leds/common.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/irq.h>

 / {
 	model = "Samsung Galaxy Exhibit (SGH-T599)";
 	compatible = "samsung,codina-tmo", "st-ericsson,u8500";

 	chosen {
 		stdout-path = &serial2;
 	};

 	battery: battery {
 		compatible = "samsung,eb425161lu";
 	};

 	thermal-zones {
 		battery-thermal {
 			/* This zone will be polled by the battery temperature code */
 			polling-delay = <0>;
 			polling-delay-passive = <0>;
 			thermal-sensors = <&bat_therm>;

 			trips {
 				battery-crit-hi {
 					temperature = <70000>;
 					hysteresis = <2000>;
 					type = "critical";
 				};
 			};
 		};
 	};

 	bat_therm: thermistor {
 		compatible = "samsung,1404-001221";
 		io-channels = <&gpadc 0x02>; /* BatTemp */
 		pullup-uv = <1800000>;
 		pullup-ohm = <230000>;
 		pulldown-ohm = <0>;
 		#thermal-sensor-cells = <0>;
 	};

 	/* TI TXS0206 level translator for 2.9 V */
 	sd_level_translator: regulator-gpio {
 		compatible = "regulator-fixed";

 		/* GPIO87 EN */
 		gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>;
 		enable-active-high;

 		regulator-name = "sd-level-translator";
 		regulator-min-microvolt = <2900000>;
 		regulator-max-microvolt = <2900000>;
 		regulator-type = "voltage";

 		startup-delay-us = <200>;

 		pinctrl-names = "default";
 		pinctrl-0 = <&sd_level_translator_default>;
 	};

 	/* External LDO MIC5366-3.3YMT for eMMC */
 	ldo_3v3_reg: regulator-gpio-ldo-3v3 {
 		compatible = "regulator-fixed";
 		/* Supplied in turn by VBAT */
 		regulator-name = "VMEM_3V3";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 		gpios = <&gpio6 31 GPIO_ACTIVE_HIGH>;
 		startup-delay-us = <5000>;
 		enable-active-high;
 		pinctrl-names = "default";
 		pinctrl-0 = <&emmc_ldo_en_default_mode>;
 	};

 	/*
 	 * External Ricoh RP152L010B-TR LCD LDO regulator for the display.
 	 * LCD_PWR_EN controls both the 3.0V output.
 	 */
 	lcd_3v0_reg: regulator-gpio-lcd-3v0 {
 		compatible = "regulator-fixed";
 		/* Supplied in turn by VBAT */
 		regulator-name = "VREG_LCD_3.0V";
 		regulator-min-microvolt = <3000000>;
 		regulator-max-microvolt = <3000000>;
 		/* GPIO219 controls this regulator */
 		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 		pinctrl-names = "default";
 		pinctrl-0 = <&lcd_pwr_en_default_mode>;
 	};

 	/*
 	 * This regulator is a GPIO line that drives the Broadcom WLAN
 	 * line WL_REG_ON high and enables the internal regulators
 	 * inside the chip. Unfortunatley it is erroneously named
 	 * WLAN_RST_N on the schematic but it is not a reset line.
 	 *
 	 * The voltage specified here is only used to determine the OCR mask,
 	 * the for the SDIO connector, the chip is actually connected
 	 * directly to VBAT.
 	 */
 	wl_reg: regulator-gpio-wlan {
 		compatible = "regulator-fixed";
 		regulator-name = "WL_REG_ON";
 		regulator-min-microvolt = <3000000>;
 		regulator-max-microvolt = <3000000>;
 		startup-delay-us = <100000>;
 		/* GPIO215 (WLAN_RST_N to WL_REG_ON) */
 		gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 		pinctrl-names = "default";
 		pinctrl-0 = <&wlan_ldo_en_default>;
 	};

 	vibrator {
 		compatible = "gpio-vibrator";
 		/* GPIO195 "MOT_EN" */
 		enable-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&vibrator_default>;
 	};

 	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&gpio_keys_default_mode>;

 		button-home {
 			linux,code = <KEY_HOME>;
 			label = "HOME";
 			/* GPIO91 */
 			gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
 		};
 		button-volup {
 			linux,code = <KEY_VOLUMEUP>;
 			label = "VOL+";
 			/* GPIO67 */
 			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
 		};
 		button-voldown {
 			linux,code = <KEY_VOLUMEDOWN>;
 			label = "VOL-";
 			/* GPIO92 */
 			gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
 		};
 	};

 	led-touchkeys {
 		compatible = "regulator-led";
 		vled-supply = <&ab8500_ldo_aux4_reg>; // 3.3V
 		default-state = "on";
 		function = LED_FUNCTION_KBD_BACKLIGHT;
 		color = <LED_COLOR_ID_WHITE>;
 	};

 	ktd253: backlight {
 		compatible = "kinetic,ktd253";
 		/* GPIO69 is used on Codina R0.4 and Codina TMO */
 		enable-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
 		/* Default to 13/32 brightness */
 		default-brightness = <13>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&ktd253_backlight_default_mode>;
 	};

 	/* Richtek RT8515GQW Flash LED Driver IC */
 	flash {
 		compatible = "richtek,rt8515";
 		/* GPIO 140 */
 		enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
 		/* GPIO 141 */
 		ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
 		/*
 		 * RFS is 16 kOhm and RTS is 100 kOhm giving
 		 * the flash max current 343mA and torch max
 		 * current 55 mA.
 		 */
 		richtek,rfs-ohms = <16000>;
 		richtek,rts-ohms = <100000>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&gpio_flash_default_mode>;

 		led {
 			function = LED_FUNCTION_FLASH;
 			color = <LED_COLOR_ID_WHITE>;
 			flash-max-timeout-us = <250000>;
 			flash-max-microamp = <343750>;
 			led-max-microamp = <55000>;
 		};
 	};

 	/* Bit-banged I2C on GPIO143 and GPIO144 also called "SUBPMU I2C" */
 	i2c-gpio-0 {
 		compatible = "i2c-gpio";
 		sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
 		scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2c_gpio_0_default>;
 		#address-cells = <1>;
 		#size-cells = <0>;

 		/* TODO: this should also be used by the SM5103 Camera power management unit */
 	};

 	/* Bit-banged I2C on GPIO151 and GPIO152 also called "COMP I2C" */
 	i2c-gpio-1 {
 		compatible = "i2c-gpio";
 		sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
 		scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2c_gpio_1_default>;
 		#address-cells = <1>;
 		#size-cells = <0>;

 		magnetometer@c {
 			compatible = "alps,hscdtd008a";
 			reg = <0x0c>;
 			clock-frequency = <400000>;

 			avdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
 			dvdd-supply = <&ab8500_ldo_aux8_reg>; // 1.8V
 		};
 	};

 	spi {
 		compatible = "spi-gpio";
 		/* Clock on GPIO220, pin SCL */
 		sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>;
 		/* MOSI on GPIO224, pin SDI "slave data in" */
 		mosi-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
 		/* MISO on GPIO225, pin SDO "slave data out" */
 		miso-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
 		/* Chip select on GPIO201 */
 		cs-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>;
 		num-chipselects = <1>;

 		pinctrl-names = "default";
 		pinctrl-0 = <&spi_gpio_0_default>;
 		#address-cells = <1>;
 		#size-cells = <0>;

 		panel@0 {
 			compatible = "samsung,s6d27a1";
 			spi-max-frequency = <1200000>;
 			/* TYPE 3: inverse clock polarity and phase */
 			spi-cpha;
 			spi-cpol;

 			reg = <0>;
 			vci-supply = <&lcd_3v0_reg>;
 			vccio-supply = <&ab8500_ldo_aux6_reg>;

 			/* Reset on GPIO139 */
 			reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
 			/* LCD_VGH/LCD_DETECT, ESD IRQ on GPIO93 */
 			interrupt-parent = <&gpio2>;
 			interrupts = <29 IRQ_TYPE_EDGE_RISING>;

 			pinctrl-names = "default";
 			pinctrl-0 = <&panel_default_mode>;
 			backlight = <&ktd253>;

 			port {
 				panel_in: endpoint {
 					remote-endpoint = <&display_out>;
 				};
 			};
 		};
 	};

 	soc {
 		/* External Micro SD slot */
 		mmc@80126000 {
 			arm,primecell-periphid = <0x10480180>;
 			max-frequency = <100000000>;
 			bus-width = <4>;
 			cap-sd-highspeed;
 			cap-mmc-highspeed;
 			st,sig-pin-fbclk;
 			full-pwr-cycle;
 			/* MMC is powered by AUX3 1.2V .. 2.91V */
 			vmmc-supply = <&ab8500_ldo_aux3_reg>;
 			/* 2.9 V level translator is using AUX3 at 2.9 V as well */
 			vqmmc-supply = <&sd_level_translator>;
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&mc0_a_2_default>;
 			pinctrl-1 = <&mc0_a_2_sleep>;
 			cd-gpios  = <&gpio6 25 GPIO_ACTIVE_LOW>; // GPIO217
 			status = "okay";
 		};

 		/* WLAN SDIO channel */
 		mmc@80118000 {
 			arm,primecell-periphid = <0x10480180>;
 			max-frequency = <50000000>;
 			bus-width = <4>;
 			non-removable;
 			cap-sd-highspeed;
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&mc1_a_2_default>;
 			pinctrl-1 = <&mc1_a_2_sleep>;
 			/*
 			 * GPIO-controlled voltage enablement: this drives
 			 * the WL_REG_ON line high when we use this device.
 			 * Represented as regulator to fill OCR mask.
 			 */
 			vmmc-supply = <&wl_reg>;

 			#address-cells = <1>;
 			#size-cells = <0>;
 			status = "okay";

 			wifi@1 {
 				compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac";
 				reg = <1>;
 				/* GPIO216 WL_HOST_WAKE */
 				interrupt-parent = <&gpio6>;
 				interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
 				interrupt-names = "host-wake";
 				pinctrl-names = "default";
 				pinctrl-0 = <&wlan_default_mode>;
 			};
 		};

 		/* eMMC */
 		mmc@80005000 {
 			arm,primecell-periphid = <0x10480180>;
 			max-frequency = <100000000>;
 			bus-width = <8>;
 			non-removable;
 			cap-mmc-highspeed;
 			mmc-ddr-1_8v;
 			no-sdio;
 			no-sd;
 			vmmc-supply = <&ldo_3v3_reg>;
 			pinctrl-names = "default", "sleep";
 			/*
 			 * GPIO130 will be set to input no pull-up resulting in a resistor
 			 * pulling the reset high and taking the memory out of reset.
 			 */
 			pinctrl-0 = <&mc2_a_1_default>;
 			pinctrl-1 = <&mc2_a_1_sleep>;
 			status = "okay";
 		};

 		/* GBF (Bluetooth) UART */
 		serial@80120000 {
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&u0_a_1_default>;
 			pinctrl-1 = <&u0_a_1_sleep>;
 			status = "okay";

 			bluetooth {
 				/* BCM4334B0 actually */
 				compatible = "brcm,bcm4330-bt";
 				/* GPIO222 rail BT_VREG_EN to BT_REG_ON */
 				shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
 				/* BT_WAKE on GPIO199 */
 				device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
 				/* BT_HOST_WAKE on GPIO97 */
 				/* FIXME: convert to interrupt */
 				host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
 				/* BT_RST_N on GPIO209 */
 				reset-gpios = <&gpio6 17 GPIO_ACTIVE_LOW>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&bluetooth_default_mode>;
 			};
 		};

 		/* GPS UART */
 		serial@80121000 {
 			status = "okay";
 			pinctrl-names = "default", "sleep";
 			/* CTS/RTS is not used, CTS is repurposed as GPIO */
 			pinctrl-0 = <&u1rxtx_a_1_default>;
 			pinctrl-1 = <&u1rxtx_a_1_sleep>;
 			/* FIXME: add a device for the GPS here */
 		};

 		/* Debugging console UART connected to AB8505 */
 		serial@80007000 {
 			status = "okay";
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&u2rxtx_c_1_default>;
 			pinctrl-1 = <&u2rxtx_c_1_sleep>;
 		};

 		prcmu@80157000 {
 			ab8505 {
 				phy {
 					pinctrl-names = "default", "sleep";
 					pinctrl-0 = <&usb_a_1_default>;
 					pinctrl-1 = <&usb_a_1_sleep>;
 				};

 				ab8500_fg {
 					line-impedance-micro-ohms = <36000>;
 				};

 				/* This is mostly identical to the Codina v0.4 regulators */
 				regulator {
 					ab8500_ldo_aux1 {
 						regulator-name = "v-sensors-vdd";
 						regulator-min-microvolt = <3000000>;
 						regulator-max-microvolt = <3300000>;
 					};

 					ab8500_ldo_aux2 {
 						regulator-name = "v-aux2";
 						regulator-min-microvolt = <3300000>;
 						regulator-max-microvolt = <3300000>;
 					};

 					ab8500_ldo_aux3 {
 						regulator-name = "v-mmc-sd";
 					};

 					ab8500_ldo_aux4 {
 						regulator-name = "v-aux4";
 						/*
 						 * Providing some span here makes the touchkey
 						 * LEDs actually dimmable.
 						 */
 						regulator-min-microvolt = <1100000>;
 						regulator-max-microvolt = <3300000>;
 					};

 					ab8500_ldo_aux5 {
 						regulator-name = "v-aux5";
 						regulator-min-microvolt = <1800000>;
 						regulator-max-microvolt = <1800000>;
 					};

 					ab8500_ldo_aux6 {
 						/* 1.8 V to the display */
 						regulator-name = "v-aux6";
 						regulator-min-microvolt = <1800000>;
 						regulator-max-microvolt = <1800000>;
 					};

 					ab8500_ldo_aux8 {
 						regulator-name = "v-sensors-vio";
 					};
 				};
 			};
 		};

 		/* I2C0 also known as "AGC I2C" */
 		i2c@80004000 {
 			status = "okay";
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&i2c0_a_1_default>;
 			pinctrl-1 = <&i2c0_a_1_sleep>;

 			proximity@39 {
 				/* Codina has the Amstaos TMD2672 */
 				compatible = "amstaos,tmd2672";
 				clock-frequency = <400000>;
 				reg = <0x39>;

 				/* IRQ on GPIO146 "PS_INT" */
 				interrupt-parent = <&gpio4>;
 				interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
 				vdd-supply = <&ab8500_ldo_aux1_reg>;
 				vddio-supply = <&ab8500_ldo_aux8_reg>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&tmd2672_codina_default>;
 			};
 		};

 		/* I2C2 on GPIO10 and GPIO11 also called "SENSORS I2C" */
 		i2c@80128000 {
 			status = "okay";
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&i2c2_b_2_default>;
 			pinctrl-1 = <&i2c2_b_2_sleep>;

 			/* Bosch BMA254 accelerometer */
 			accelerometer@18 {
 				compatible = "bosch,bma254";
 				reg = <0x18>;
 				mount-matrix = "0", "1", "0",
 					       "-1", "0", "0",
 					       "0", "0", "1";
 				vddio-supply = <&ab8500_ldo_aux8_reg>; // 1.8V
 				vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
 			};
 		};

 		/* I2C3 */
 		i2c@80110000 {
 			status = "okay";

 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&i2c3_c_2_default>;
 			pinctrl-1 = <&i2c3_c_2_sleep>;

 			/* TODO: write bindings and driver for this touchscreen */

 			/* Zinitix BT404 ISP part */
 			isp@50 {
 				compatible = "zinitix,bt404-isp";
 				reg = <0x50>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&tsp_default>;
 			};

 			/* Zinitix BT404 touchscreen, also has the touchkeys for menu and back */
 			touchscreen@20 {
 				compatible = "zinitix,bt404";
 				reg = <0x20>;
 				/* GPIO218 (TSP_INT_1V8) */
 				interrupt-parent = <&gpio6>;
 				interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
 				vcca-supply = <&ab8500_ldo_aux2_reg>; // 3.3V
 				vdd-supply = <&ab8500_ldo_aux5_reg>; // 1.8V
 				zinitix,mode = <2>;
 				touchscreen-size-x = <480>;
 				touchscreen-size-y = <800>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&tsp_default>;
 			};
 		};

 		mcde@a0350000 {
 			status = "okay";
 			pinctrl-names = "default";
 			pinctrl-0 = <&dpi_default_mode>;

 			port {
 				display_out: endpoint {
 					remote-endpoint = <&panel_in>;
 				};
 			};
 		};
 	};
 };

 &pinctrl {
 	/*
 	 * This extends the MC0_A_2 default config to include
 	 * the card detect GPIO217 line.
 	 */
 	sdi0 {
 		mc0_a_2_default {
 			default_cfg4 {
 				pins = "GPIO217_AH12"; /* card detect */
 				ste,config = <&gpio_in_pd>;
 			};
 		};
 	};
 	sdi2 {
 		/*
 		 * GPIO130 should be set in GPIO mode and
 		 * pulled down. (Not connected.)
 		 */
 		mc2_a_1_default {
 			default_cfg2 {
 				pins = "GPIO130_C8"; /* FBCLK */
 				ste,config = <&gpio_in_pd>;
 			};
 		};
 	};
 	/* GPIO that enables the 2.9V SD card level translator */
 	sd-level-translator {
 		sd_level_translator_default: sd_level_translator_default {
 			/* level shifter on GPIO87 */
 			codina_cfg1 {
 				pins = "GPIO87_B3";
 				ste,config = <&gpio_out_hi>;
 			};
 		};
 	};
 	/* GPIO that enables the LDO regulator for the eMMC */
 	emmc-ldo {
 		emmc_ldo_en_default_mode: emmc_ldo_default {
 			/* LDO enable on GPIO223 */
 			codina_cfg1 {
 				pins = "GPIO223_AH9";
 				ste,config = <&gpio_out_hi>;
 			};
 		};
 	};
 	/* GPIOs for panel control */
 	panel {
 		panel_default_mode: panel_default {
 			codina_cfg1 {
 				/* Reset line */
 				pins = "GPIO139_C9";
 				ste,config = <&gpio_out_lo>;
 			};
 			codina_cfg2 {
 				/* ESD IRQ line "LCD detect" */
 				pins = "GPIO93_B7";
 				ste,config = <&gpio_in_nopull>;
 			};
 		};
 	};
 	/* GPIO that enables the LDO regulator for the LCD display */
 	lcd-ldo {
 		lcd_pwr_en_default_mode: lcd_pwr_en_default {
 			/* LCD_PWR_EN on GPIO219 */
 			codina_cfg1 {
 				pins = "GPIO219_AG10";
 				ste,config = <&gpio_out_hi>;
 			};
 		};
 	};
 	/* GPIO that enables the WLAN internal LDO regulators */
 	wlan-ldo {
 		wlan_ldo_en_default: wlan_ldo_default {
 			/* GPIO215 named WLAN_RST_N */
 			codina_cfg1 {
 				pins = "GPIO215_AH13";
 				ste,config = <&gpio_out_lo>;
 			};
 		};
 	};
 	/* Backlight GPIO */
 	backlight {
 		ktd253_backlight_default_mode: backlight_default {
 			skomer_cfg1 {
 				pins = "GPIO69_E2"; /* LCD_BL_CTRL */
 				ste,config = <&gpio_out_lo>;
 			};
 		};
 	};
 	/* Flash and torch */
 	flash {
 		gpio_flash_default_mode: flash_default {
 			codina_cfg1 {
 				pins = "GPIO140_B11", "GPIO141_C12";
 				ste,config = <&gpio_out_lo>;
 			};
 		};
 	};
 	/* GPIO keys */
 	gpio-keys {
 		gpio_keys_default_mode: gpio_keys_default {
 			skomer_cfg1 {
 				pins = "GPIO67_G2", /* VOL UP */
 				       "GPIO91_B6", /* HOME */
 				       "GPIO92_D6"; /* VOL DOWN */
 				ste,config = <&gpio_in_pu>;
 			};
 		};
 	};
 	/* Interrupt line for the Zinitix BT404 touchscreen */
 	tsp {
 		tsp_default: tsp_default {
 			codina_cfg1 {
 				pins = "GPIO218_AH11";	/* TSP_INT_1V8 */
 				ste,config = <&gpio_in_nopull>;
 			};
 		};
 	};
 	/* Interrupt line for light/proximity sensor TMD2672 */
 	tmd2672 {
 		tmd2672_codina_default: tmd2672_codina {
 			codina_cfg1 {
 				pins = "GPIO146_D13";
 				ste,config = <&gpio_in_nopull>;
 			};
 		};
 	};
 	/* GPIO-based I2C bus for subpmu */
 	i2c-gpio-0 {
 		i2c_gpio_0_default: i2c_gpio_0 {
 			codina_cfg1 {
 				pins = "GPIO143_D12", "GPIO144_B13";
 				ste,config = <&gpio_in_nopull>;
 			};
 		};
 	};
 	/* GPIO-based I2C bus for the NFC */
 	i2c-gpio-1 {
 		i2c_gpio_1_default: i2c_gpio_1 {
 			codina_cfg1 {
 				pins = "GPIO151_D17", "GPIO152_D16";
 				ste,config = <&gpio_in_nopull>;
 			};
 		};
 	};
 	/* GPIO-based SPI bus for the display */
 	spi-gpio-0 {
 		spi_gpio_0_default: spi_gpio_0_d {
 			codina_cfg1 {
 				pins = "GPIO220_AH10", "GPIO201_AF24", "GPIO224_AG9";
 				ste,config = <&gpio_out_hi>;
 			};
 			codina_cfg2 {
 				pins = "GPIO225_AG8";
 				/* Needs pull down, no pull down resistor on board */
 				ste,config = <&gpio_in_pd>;
 			};
 		};
 		spi_gpio_0_sleep: spi_gpio_0_s {
 			codina_cfg1 {
 				pins = "GPIO220_AH10", "GPIO201_AF24",
 				       "GPIO224_AG9", "GPIO225_AG8";
 				ste,config = <&gpio_out_hi>;
 			};
 		};
 	};
 	wlan {
 		wlan_default_mode: wlan_default {
 			/* GPIO216 for WL_HOST_WAKE */
 			codina_cfg2 {
 				pins = "GPIO216_AG12";
 				ste,config = <&gpio_in_pd>;
 			};
 		};
 	};
 	bluetooth {
 		bluetooth_default_mode: bluetooth_default {
 			/* GPIO199 BT_WAKE and GPIO222 BT_VREG_ON */
 			codina_cfg1 {
 				pins = "GPIO199_AH23", "GPIO222_AJ9";
 				ste,config = <&gpio_out_lo>;
 			};
 			/* GPIO97 BT_HOST_WAKE */
 			codina_cfg2 {
 				pins = "GPIO97_D9";
 				ste,config = <&gpio_in_nopull>;
 			};
 			/* GPIO209 BT_RST_N */
 			codina_cfg3 {
 				pins = "GPIO209_AG15";
 				ste,config = <&gpio_out_hi>;
 			};
 		};
 	};
 	vibrator {
 		vibrator_default: vibrator_default {
 			codina_cfg1 {
 				pins = "GPIO195_AG28";	/* MOT_EN */
 				ste,config = <&gpio_out_lo>;
 			};
 		};
 	};
 	mcde {
 		dpi_default_mode: dpi_default {
 			default_mux1 {
 				/* Mux in all the data lines */
 				function = "lcd";
 				groups =
 					/* Data lines D0-D7 GPIO70..GPIO77 */
 					"lcd_d0_d7_a_1",
 					/* Data lines D8-D11 GPIO78..GPIO81 */
 					"lcd_d8_d11_a_1",
 					/* Data lines D12-D15 GPIO82..GPIO85 */
 					"lcd_d12_d15_a_1",
 					/* Data lines D16-D23 GPIO161..GPIO168 */
 					"lcd_d16_d23_b_1";
 			};
 			default_mux2 {
 				function = "lcda";
 				/* Clock line on GPIO150, DE, VSO, HSO on GPIO169..GPIO171 */
 				groups = "lcdaclk_b_1", "lcda_b_1";
 			};
 			/* Input, no pull-up is the default state for pins used for an alt function */
 			default_cfg1 {
 				pins = "GPIO150_C14", "GPIO169_D22", "GPIO170_C23", "GPIO171_D23";
 				ste,config = <&in_nopull>;
 			};
 		};
 	};
 };
	// SPDX-License-Identifier: GPL-2.0-only
	/*
	* Devicetree for the Samsung Galaxy Exhibit SGH-T599 also known as Codina-TMO,
	* the "TMO" shall be read "T-Mobile" as this phone was produced exlusively
	* for T-Mobile in the United States.
	*
	* This phone is closely related to the Codina, but has:
	* - No CPU speed cap, full ~1GHz rate
	* - Different power management IC, AB8505
	* - As AB8505 has a micro USB phy, no TI TSU6111
	* - Different power routing such as the removal of the external LDO for the
	* touchscreen in favor of using the AB8505
	* - Using a regulator for the key backlight LED
	* - Using the Samsung S6D27A1 panel by default
	* - The panel is using one of the ordinary AB8505 regulators for 1.8V
	* - WiFi/Bluetooth combi chip upgraded to BCM4334
	* - GPIO for backlight control moved from 68 to 69
	*/

	/dts-v1/;
	#include "ste-db8500.dtsi"
	#include "ste-ab8505.dtsi"
	#include "ste-dbx5x0-pinctrl.dtsi"
	#include <dt-bindings/gpio/gpio.h>
	#include <dt-bindings/leds/common.h>
	#include <dt-bindings/input/input.h>
	#include <dt-bindings/interrupt-controller/irq.h>

	/ {
	model = "Samsung Galaxy Exhibit (SGH-T599)";
	compatible = "samsung,codina-tmo", "st-ericsson,u8500";

	chosen {
	stdout-path = &serial2;
	};

	battery: battery {
	compatible = "samsung,eb425161lu";
	};

	thermal-zones {
	battery-thermal {
	/* This zone will be polled by the battery temperature code */
	polling-delay = <0>;
	polling-delay-passive = <0>;
	thermal-sensors = <&bat_therm>;

	trips {
	battery-crit-hi {
	temperature = <70000>;
	hysteresis = <2000>;
	type = "critical";
	};
	};
	};
	};

	bat_therm: thermistor {
	compatible = "samsung,1404-001221";
	io-channels = <&gpadc 0x02>; /* BatTemp */
	pullup-uv = <1800000>;
	pullup-ohm = <230000>;
	pulldown-ohm = <0>;
	#thermal-sensor-cells = <0>;
	};

	/* TI TXS0206 level translator for 2.9 V */
	sd_level_translator: regulator-gpio {
	compatible = "regulator-fixed";

	/* GPIO87 EN */
	gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>;
	enable-active-high;

	regulator-name = "sd-level-translator";
	regulator-min-microvolt = <2900000>;
	regulator-max-microvolt = <2900000>;
	regulator-type = "voltage";

	startup-delay-us = <200>;

	pinctrl-names = "default";
	pinctrl-0 = <&sd_level_translator_default>;
	};

	/* External LDO MIC5366-3.3YMT for eMMC */
	ldo_3v3_reg: regulator-gpio-ldo-3v3 {
	compatible = "regulator-fixed";
	/* Supplied in turn by VBAT */
	regulator-name = "VMEM_3V3";
	regulator-min-microvolt = <3300000>;
	regulator-max-microvolt = <3300000>;
	gpios = <&gpio6 31 GPIO_ACTIVE_HIGH>;
	startup-delay-us = <5000>;
	enable-active-high;
	pinctrl-names = "default";
	pinctrl-0 = <&emmc_ldo_en_default_mode>;
	};

	/*
	* External Ricoh RP152L010B-TR LCD LDO regulator for the display.
	* LCD_PWR_EN controls both the 3.0V output.
	*/
	lcd_3v0_reg: regulator-gpio-lcd-3v0 {
	compatible = "regulator-fixed";
	/* Supplied in turn by VBAT */
	regulator-name = "VREG_LCD_3.0V";
	regulator-min-microvolt = <3000000>;
	regulator-max-microvolt = <3000000>;
	/* GPIO219 controls this regulator */
	gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
	enable-active-high;
	pinctrl-names = "default";
	pinctrl-0 = <&lcd_pwr_en_default_mode>;
	};

	/*
	* This regulator is a GPIO line that drives the Broadcom WLAN
	* line WL_REG_ON high and enables the internal regulators
	* inside the chip. Unfortunatley it is erroneously named
	* WLAN_RST_N on the schematic but it is not a reset line.
	*
	* The voltage specified here is only used to determine the OCR mask,
	* the for the SDIO connector, the chip is actually connected
	* directly to VBAT.
	*/
	wl_reg: regulator-gpio-wlan {
	compatible = "regulator-fixed";
	regulator-name = "WL_REG_ON";
	regulator-min-microvolt = <3000000>;
	regulator-max-microvolt = <3000000>;
	startup-delay-us = <100000>;
	/* GPIO215 (WLAN_RST_N to WL_REG_ON) */
	gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>;
	enable-active-high;
	pinctrl-names = "default";
	pinctrl-0 = <&wlan_ldo_en_default>;
	};

	vibrator {
	compatible = "gpio-vibrator";
	/* GPIO195 "MOT_EN" */
	enable-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>;
	pinctrl-names = "default";
	pinctrl-0 = <&vibrator_default>;
	};

	gpio-keys {
	compatible = "gpio-keys";
	pinctrl-names = "default";
	pinctrl-0 = <&gpio_keys_default_mode>;

	button-home {
	linux,code = <KEY_HOME>;
	label = "HOME";
	/* GPIO91 */
	gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
	};
	button-volup {
	linux,code = <KEY_VOLUMEUP>;
	label = "VOL+";
	/* GPIO67 */
	gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
	};
	button-voldown {
	linux,code = <KEY_VOLUMEDOWN>;
	label = "VOL-";
	/* GPIO92 */
	gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
	};
	};

	led-touchkeys {
	compatible = "regulator-led";
	vled-supply = <&ab8500_ldo_aux4_reg>; // 3.3V
	default-state = "on";
	function = LED_FUNCTION_KBD_BACKLIGHT;
	color = <LED_COLOR_ID_WHITE>;
	};

	ktd253: backlight {
	compatible = "kinetic,ktd253";
	/* GPIO69 is used on Codina R0.4 and Codina TMO */
	enable-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
	/* Default to 13/32 brightness */
	default-brightness = <13>;
	pinctrl-names = "default";
	pinctrl-0 = <&ktd253_backlight_default_mode>;
	};

	/* Richtek RT8515GQW Flash LED Driver IC */
	flash {
	compatible = "richtek,rt8515";
	/* GPIO 140 */
	enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
	/* GPIO 141 */
	ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
	/*
	* RFS is 16 kOhm and RTS is 100 kOhm giving
	* the flash max current 343mA and torch max
	* current 55 mA.
	*/
	richtek,rfs-ohms = <16000>;
	richtek,rts-ohms = <100000>;
	pinctrl-names = "default";
	pinctrl-0 = <&gpio_flash_default_mode>;

	led {
	function = LED_FUNCTION_FLASH;
	color = <LED_COLOR_ID_WHITE>;
	flash-max-timeout-us = <250000>;
	flash-max-microamp = <343750>;
	led-max-microamp = <55000>;
	};
	};

	/* Bit-banged I2C on GPIO143 and GPIO144 also called "SUBPMU I2C" */
	i2c-gpio-0 {
	compatible = "i2c-gpio";
	sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH\|GPIO_OPEN_DRAIN)>;
	scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH\|GPIO_OPEN_DRAIN)>;
	pinctrl-names = "default";
	pinctrl-0 = <&i2c_gpio_0_default>;
	#address-cells = <1>;
	#size-cells = <0>;

	/* TODO: this should also be used by the SM5103 Camera power management unit */
	};

	/* Bit-banged I2C on GPIO151 and GPIO152 also called "COMP I2C" */
	i2c-gpio-1 {
	compatible = "i2c-gpio";
	sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH\|GPIO_OPEN_DRAIN)>;
	scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH\|GPIO_OPEN_DRAIN)>;
	pinctrl-names = "default";
	pinctrl-0 = <&i2c_gpio_1_default>;
	#address-cells = <1>;
	#size-cells = <0>;

	magnetometer@c {
	compatible = "alps,hscdtd008a";
	reg = <0x0c>;
	clock-frequency = <400000>;

	avdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
	dvdd-supply = <&ab8500_ldo_aux8_reg>; // 1.8V
	};
	};

	spi {
	compatible = "spi-gpio";
	/* Clock on GPIO220, pin SCL */
	sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>;
	/* MOSI on GPIO224, pin SDI "slave data in" */
	mosi-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
	/* MISO on GPIO225, pin SDO "slave data out" */
	miso-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
	/* Chip select on GPIO201 */
	cs-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>;
	num-chipselects = <1>;

	pinctrl-names = "default";
	pinctrl-0 = <&spi_gpio_0_default>;
	#address-cells = <1>;
	#size-cells = <0>;

	panel@0 {
	compatible = "samsung,s6d27a1";
	spi-max-frequency = <1200000>;
	/* TYPE 3: inverse clock polarity and phase */
	spi-cpha;
	spi-cpol;

	reg = <0>;
	vci-supply = <&lcd_3v0_reg>;
	vccio-supply = <&ab8500_ldo_aux6_reg>;

	/* Reset on GPIO139 */
	reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
	/* LCD_VGH/LCD_DETECT, ESD IRQ on GPIO93 */
	interrupt-parent = <&gpio2>;
	interrupts = <29 IRQ_TYPE_EDGE_RISING>;

	pinctrl-names = "default";
	pinctrl-0 = <&panel_default_mode>;
	backlight = <&ktd253>;

	port {
	panel_in: endpoint {
	remote-endpoint = <&display_out>;
	};
	};
	};
	};

	soc {
	/* External Micro SD slot */
	mmc@80126000 {
	arm,primecell-periphid = <0x10480180>;
	max-frequency = <100000000>;
	bus-width = <4>;
	cap-sd-highspeed;
	cap-mmc-highspeed;
	st,sig-pin-fbclk;
	full-pwr-cycle;
	/* MMC is powered by AUX3 1.2V .. 2.91V */
	vmmc-supply = <&ab8500_ldo_aux3_reg>;
	/* 2.9 V level translator is using AUX3 at 2.9 V as well */
	vqmmc-supply = <&sd_level_translator>;
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&mc0_a_2_default>;
	pinctrl-1 = <&mc0_a_2_sleep>;
	cd-gpios = <&gpio6 25 GPIO_ACTIVE_LOW>; // GPIO217
	status = "okay";
	};

	/* WLAN SDIO channel */
	mmc@80118000 {
	arm,primecell-periphid = <0x10480180>;
	max-frequency = <50000000>;
	bus-width = <4>;
	non-removable;
	cap-sd-highspeed;
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&mc1_a_2_default>;
	pinctrl-1 = <&mc1_a_2_sleep>;
	/*
	* GPIO-controlled voltage enablement: this drives
	* the WL_REG_ON line high when we use this device.
	* Represented as regulator to fill OCR mask.
	*/
	vmmc-supply = <&wl_reg>;

	#address-cells = <1>;
	#size-cells = <0>;
	status = "okay";

	wifi@1 {
	compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac";
	reg = <1>;
	/* GPIO216 WL_HOST_WAKE */
	interrupt-parent = <&gpio6>;
	interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
	interrupt-names = "host-wake";
	pinctrl-names = "default";
	pinctrl-0 = <&wlan_default_mode>;
	};
	};

	/* eMMC */
	mmc@80005000 {
	arm,primecell-periphid = <0x10480180>;
	max-frequency = <100000000>;
	bus-width = <8>;
	non-removable;
	cap-mmc-highspeed;
	mmc-ddr-1_8v;
	no-sdio;
	no-sd;
	vmmc-supply = <&ldo_3v3_reg>;
	pinctrl-names = "default", "sleep";
	/*
	* GPIO130 will be set to input no pull-up resulting in a resistor
	* pulling the reset high and taking the memory out of reset.
	*/
	pinctrl-0 = <&mc2_a_1_default>;
	pinctrl-1 = <&mc2_a_1_sleep>;
	status = "okay";
	};

	/* GBF (Bluetooth) UART */
	serial@80120000 {
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&u0_a_1_default>;
	pinctrl-1 = <&u0_a_1_sleep>;
	status = "okay";

	bluetooth {
	/* BCM4334B0 actually */
	compatible = "brcm,bcm4330-bt";
	/* GPIO222 rail BT_VREG_EN to BT_REG_ON */
	shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
	/* BT_WAKE on GPIO199 */
	device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
	/* BT_HOST_WAKE on GPIO97 */
	/* FIXME: convert to interrupt */
	host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
	/* BT_RST_N on GPIO209 */
	reset-gpios = <&gpio6 17 GPIO_ACTIVE_LOW>;
	pinctrl-names = "default";
	pinctrl-0 = <&bluetooth_default_mode>;
	};
	};

	/* GPS UART */
	serial@80121000 {
	status = "okay";
	pinctrl-names = "default", "sleep";
	/* CTS/RTS is not used, CTS is repurposed as GPIO */
	pinctrl-0 = <&u1rxtx_a_1_default>;
	pinctrl-1 = <&u1rxtx_a_1_sleep>;
	/* FIXME: add a device for the GPS here */
	};

	/* Debugging console UART connected to AB8505 */
	serial@80007000 {
	status = "okay";
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&u2rxtx_c_1_default>;
	pinctrl-1 = <&u2rxtx_c_1_sleep>;
	};

	prcmu@80157000 {
	ab8505 {
	phy {
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&usb_a_1_default>;
	pinctrl-1 = <&usb_a_1_sleep>;
	};

	ab8500_fg {
	line-impedance-micro-ohms = <36000>;
	};

	/* This is mostly identical to the Codina v0.4 regulators */
	regulator {
	ab8500_ldo_aux1 {
	regulator-name = "v-sensors-vdd";
	regulator-min-microvolt = <3000000>;
	regulator-max-microvolt = <3300000>;
	};

	ab8500_ldo_aux2 {
	regulator-name = "v-aux2";
	regulator-min-microvolt = <3300000>;
	regulator-max-microvolt = <3300000>;
	};

	ab8500_ldo_aux3 {
	regulator-name = "v-mmc-sd";
	};

	ab8500_ldo_aux4 {
	regulator-name = "v-aux4";
	/*
	* Providing some span here makes the touchkey
	* LEDs actually dimmable.
	*/
	regulator-min-microvolt = <1100000>;
	regulator-max-microvolt = <3300000>;
	};

	ab8500_ldo_aux5 {
	regulator-name = "v-aux5";
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <1800000>;
	};

	ab8500_ldo_aux6 {
	/* 1.8 V to the display */
	regulator-name = "v-aux6";
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <1800000>;
	};

	ab8500_ldo_aux8 {
	regulator-name = "v-sensors-vio";
	};
	};
	};
	};

	/* I2C0 also known as "AGC I2C" */
	i2c@80004000 {
	status = "okay";
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&i2c0_a_1_default>;
	pinctrl-1 = <&i2c0_a_1_sleep>;

	proximity@39 {
	/* Codina has the Amstaos TMD2672 */
	compatible = "amstaos,tmd2672";
	clock-frequency = <400000>;
	reg = <0x39>;

	/* IRQ on GPIO146 "PS_INT" */
	interrupt-parent = <&gpio4>;
	interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
	vdd-supply = <&ab8500_ldo_aux1_reg>;
	vddio-supply = <&ab8500_ldo_aux8_reg>;
	pinctrl-names = "default";
	pinctrl-0 = <&tmd2672_codina_default>;
	};
	};

	/* I2C2 on GPIO10 and GPIO11 also called "SENSORS I2C" */
	i2c@80128000 {
	status = "okay";
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&i2c2_b_2_default>;
	pinctrl-1 = <&i2c2_b_2_sleep>;

	/* Bosch BMA254 accelerometer */
	accelerometer@18 {
	compatible = "bosch,bma254";
	reg = <0x18>;
	mount-matrix = "0", "1", "0",
	"-1", "0", "0",
	"0", "0", "1";
	vddio-supply = <&ab8500_ldo_aux8_reg>; // 1.8V
	vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
	};
	};

	/* I2C3 */
	i2c@80110000 {
	status = "okay";

	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&i2c3_c_2_default>;
	pinctrl-1 = <&i2c3_c_2_sleep>;

	/* TODO: write bindings and driver for this touchscreen */

	/* Zinitix BT404 ISP part */
	isp@50 {
	compatible = "zinitix,bt404-isp";
	reg = <0x50>;
	pinctrl-names = "default";
	pinctrl-0 = <&tsp_default>;
	};

	/* Zinitix BT404 touchscreen, also has the touchkeys for menu and back */
	touchscreen@20 {
	compatible = "zinitix,bt404";
	reg = <0x20>;
	/* GPIO218 (TSP_INT_1V8) */
	interrupt-parent = <&gpio6>;
	interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
	vcca-supply = <&ab8500_ldo_aux2_reg>; // 3.3V
	vdd-supply = <&ab8500_ldo_aux5_reg>; // 1.8V
	zinitix,mode = <2>;
	touchscreen-size-x = <480>;
	touchscreen-size-y = <800>;
	pinctrl-names = "default";
	pinctrl-0 = <&tsp_default>;
	};
	};

	mcde@a0350000 {
	status = "okay";
	pinctrl-names = "default";
	pinctrl-0 = <&dpi_default_mode>;

	port {
	display_out: endpoint {
	remote-endpoint = <&panel_in>;
	};
	};
	};
	};
	};

	&pinctrl {
	/*
	* This extends the MC0_A_2 default config to include
	* the card detect GPIO217 line.
	*/
	sdi0 {
	mc0_a_2_default {
	default_cfg4 {
	pins = "GPIO217_AH12"; /* card detect */
	ste,config = <&gpio_in_pd>;
	};
	};
	};
	sdi2 {
	/*
	* GPIO130 should be set in GPIO mode and
	* pulled down. (Not connected.)
	*/
	mc2_a_1_default {
	default_cfg2 {
	pins = "GPIO130_C8"; /* FBCLK */
	ste,config = <&gpio_in_pd>;
	};
	};
	};
	/* GPIO that enables the 2.9V SD card level translator */
	sd-level-translator {
	sd_level_translator_default: sd_level_translator_default {
	/* level shifter on GPIO87 */
	codina_cfg1 {
	pins = "GPIO87_B3";
	ste,config = <&gpio_out_hi>;
	};
	};
	};
	/* GPIO that enables the LDO regulator for the eMMC */
	emmc-ldo {
	emmc_ldo_en_default_mode: emmc_ldo_default {
	/* LDO enable on GPIO223 */
	codina_cfg1 {
	pins = "GPIO223_AH9";
	ste,config = <&gpio_out_hi>;
	};
	};
	};
	/* GPIOs for panel control */
	panel {
	panel_default_mode: panel_default {
	codina_cfg1 {
	/* Reset line */
	pins = "GPIO139_C9";
	ste,config = <&gpio_out_lo>;
	};
	codina_cfg2 {
	/* ESD IRQ line "LCD detect" */
	pins = "GPIO93_B7";
	ste,config = <&gpio_in_nopull>;
	};
	};
	};
	/* GPIO that enables the LDO regulator for the LCD display */
	lcd-ldo {
	lcd_pwr_en_default_mode: lcd_pwr_en_default {
	/* LCD_PWR_EN on GPIO219 */
	codina_cfg1 {
	pins = "GPIO219_AG10";
	ste,config = <&gpio_out_hi>;
	};
	};
	};
	/* GPIO that enables the WLAN internal LDO regulators */
	wlan-ldo {
	wlan_ldo_en_default: wlan_ldo_default {
	/* GPIO215 named WLAN_RST_N */
	codina_cfg1 {
	pins = "GPIO215_AH13";
	ste,config = <&gpio_out_lo>;
	};
	};
	};
	/* Backlight GPIO */
	backlight {
	ktd253_backlight_default_mode: backlight_default {
	skomer_cfg1 {
	pins = "GPIO69_E2"; /* LCD_BL_CTRL */
	ste,config = <&gpio_out_lo>;
	};
	};
	};
	/* Flash and torch */
	flash {
	gpio_flash_default_mode: flash_default {
	codina_cfg1 {
	pins = "GPIO140_B11", "GPIO141_C12";
	ste,config = <&gpio_out_lo>;
	};
	};
	};
	/* GPIO keys */
	gpio-keys {
	gpio_keys_default_mode: gpio_keys_default {
	skomer_cfg1 {
	pins = "GPIO67_G2", /* VOL UP */
	"GPIO91_B6", /* HOME */
	"GPIO92_D6"; /* VOL DOWN */
	ste,config = <&gpio_in_pu>;
	};
	};
	};
	/* Interrupt line for the Zinitix BT404 touchscreen */
	tsp {
	tsp_default: tsp_default {
	codina_cfg1 {
	pins = "GPIO218_AH11"; /* TSP_INT_1V8 */
	ste,config = <&gpio_in_nopull>;
	};
	};
	};
	/* Interrupt line for light/proximity sensor TMD2672 */
	tmd2672 {
	tmd2672_codina_default: tmd2672_codina {
	codina_cfg1 {
	pins = "GPIO146_D13";
	ste,config = <&gpio_in_nopull>;
	};
	};
	};
	/* GPIO-based I2C bus for subpmu */
	i2c-gpio-0 {
	i2c_gpio_0_default: i2c_gpio_0 {
	codina_cfg1 {
	pins = "GPIO143_D12", "GPIO144_B13";
	ste,config = <&gpio_in_nopull>;
	};
	};
	};
	/* GPIO-based I2C bus for the NFC */
	i2c-gpio-1 {
	i2c_gpio_1_default: i2c_gpio_1 {
	codina_cfg1 {
	pins = "GPIO151_D17", "GPIO152_D16";
	ste,config = <&gpio_in_nopull>;
	};
	};
	};
	/* GPIO-based SPI bus for the display */
	spi-gpio-0 {
	spi_gpio_0_default: spi_gpio_0_d {
	codina_cfg1 {
	pins = "GPIO220_AH10", "GPIO201_AF24", "GPIO224_AG9";
	ste,config = <&gpio_out_hi>;
	};
	codina_cfg2 {
	pins = "GPIO225_AG8";
	/* Needs pull down, no pull down resistor on board */
	ste,config = <&gpio_in_pd>;
	};
	};
	spi_gpio_0_sleep: spi_gpio_0_s {
	codina_cfg1 {
	pins = "GPIO220_AH10", "GPIO201_AF24",
	"GPIO224_AG9", "GPIO225_AG8";
	ste,config = <&gpio_out_hi>;
	};
	};
	};
	wlan {
	wlan_default_mode: wlan_default {
	/* GPIO216 for WL_HOST_WAKE */
	codina_cfg2 {
	pins = "GPIO216_AG12";
	ste,config = <&gpio_in_pd>;
	};
	};
	};
	bluetooth {
	bluetooth_default_mode: bluetooth_default {
	/* GPIO199 BT_WAKE and GPIO222 BT_VREG_ON */
	codina_cfg1 {
	pins = "GPIO199_AH23", "GPIO222_AJ9";
	ste,config = <&gpio_out_lo>;
	};
	/* GPIO97 BT_HOST_WAKE */
	codina_cfg2 {
	pins = "GPIO97_D9";
	ste,config = <&gpio_in_nopull>;
	};
	/* GPIO209 BT_RST_N */
	codina_cfg3 {
	pins = "GPIO209_AG15";
	ste,config = <&gpio_out_hi>;
	};
	};
	};
	vibrator {
	vibrator_default: vibrator_default {
	codina_cfg1 {
	pins = "GPIO195_AG28"; /* MOT_EN */
	ste,config = <&gpio_out_lo>;
	};
	};
	};
	mcde {
	dpi_default_mode: dpi_default {
	default_mux1 {
	/* Mux in all the data lines */
	function = "lcd";
	groups =
	/* Data lines D0-D7 GPIO70..GPIO77 */
	"lcd_d0_d7_a_1",
	/* Data lines D8-D11 GPIO78..GPIO81 */
	"lcd_d8_d11_a_1",
	/* Data lines D12-D15 GPIO82..GPIO85 */
	"lcd_d12_d15_a_1",
	/* Data lines D16-D23 GPIO161..GPIO168 */
	"lcd_d16_d23_b_1";
	};
	default_mux2 {
	function = "lcda";
	/* Clock line on GPIO150, DE, VSO, HSO on GPIO169..GPIO171 */
	groups = "lcdaclk_b_1", "lcda_b_1";
	};
	/* Input, no pull-up is the default state for pins used for an alt function */
	default_cfg1 {
	pins = "GPIO150_C14", "GPIO169_D22", "GPIO170_C23", "GPIO171_D23";
	ste,config = <&in_nopull>;
	};
	};
	};
	};