| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Copyright (c) 2016 Andreas Färber |
| */ |
| |
| #include "meson-gxbb.dtsi" |
| #include <dt-bindings/sound/meson-aiu.h> |
| |
| / { |
| compatible = "tronsmart,vega-s95", "amlogic,meson-gxbb"; |
| |
| aliases { |
| serial0 = &uart_AO; |
| ethernet0 = ðmac; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| spdif_dit: audio-codec-0 { |
| #sound-dai-cells = <0>; |
| compatible = "linux,spdif-dit"; |
| status = "okay"; |
| sound-name-prefix = "DIT"; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| |
| led-blue { |
| label = "vega-s95:blue:on"; |
| gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_HIGH>; |
| default-state = "on"; |
| panic-indicator; |
| }; |
| }; |
| |
| usb_pwr: regulator-usb-pwrs { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "USB_PWR"; |
| |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| |
| gpio = <&gpio GPIODV_24 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| vddio_boot: regulator-vddio_boot { |
| compatible = "regulator-fixed"; |
| regulator-name = "VDDIO_BOOT"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| vddao_3v3: regulator-vddao_3v3 { |
| compatible = "regulator-fixed"; |
| regulator-name = "VDDAO_3V3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| vddio_ao18: regulator-vddio_ao18 { |
| compatible = "regulator-fixed"; |
| regulator-name = "VDDIO_AO18"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| vcc_3v3: regulator-vcc_3v3 { |
| compatible = "regulator-fixed"; |
| regulator-name = "VCC_3V3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| emmc_pwrseq: emmc-pwrseq { |
| compatible = "mmc-pwrseq-emmc"; |
| reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>; |
| }; |
| |
| wifi32k: wifi32k { |
| compatible = "pwm-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <32768>; |
| pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */ |
| }; |
| |
| hdmi-connector { |
| compatible = "hdmi-connector"; |
| type = "a"; |
| |
| port { |
| hdmi_connector_in: endpoint { |
| remote-endpoint = <&hdmi_tx_tmds_out>; |
| }; |
| }; |
| }; |
| |
| sdio_pwrseq: sdio-pwrseq { |
| compatible = "mmc-pwrseq-simple"; |
| reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>; |
| clocks = <&wifi32k>; |
| clock-names = "ext_clock"; |
| }; |
| |
| sound { |
| compatible = "amlogic,gx-sound-card"; |
| model = "VEGA-S95"; |
| assigned-clocks = <&clkc CLKID_MPLL0>, |
| <&clkc CLKID_MPLL1>, |
| <&clkc CLKID_MPLL2>; |
| assigned-clock-parents = <0>, <0>, <0>; |
| assigned-clock-rates = <294912000>, |
| <270950400>, |
| <393216000>; |
| |
| dai-link-0 { |
| sound-dai = <&aiu AIU_CPU CPU_I2S_FIFO>; |
| }; |
| |
| dai-link-1 { |
| sound-dai = <&aiu AIU_CPU CPU_SPDIF_FIFO>; |
| }; |
| |
| dai-link-2 { |
| sound-dai = <&aiu AIU_CPU CPU_I2S_ENCODER>; |
| dai-format = "i2s"; |
| mclk-fs = <256>; |
| |
| codec-0 { |
| sound-dai = <&aiu AIU_HDMI CTRL_I2S>; |
| }; |
| }; |
| |
| dai-link-3 { |
| sound-dai = <&aiu AIU_CPU CPU_SPDIF_ENCODER>; |
| |
| codec-0 { |
| sound-dai = <&spdif_dit>; |
| }; |
| }; |
| |
| dai-link-4 { |
| sound-dai = <&aiu AIU_HDMI CTRL_OUT>; |
| |
| codec-0 { |
| sound-dai = <&hdmi_tx>; |
| }; |
| }; |
| }; |
| }; |
| |
| &aiu { |
| status = "okay"; |
| pinctrl-0 = <&spdif_out_y_pins>; |
| pinctrl-names = "default"; |
| }; |
| |
| &cec_AO { |
| status = "okay"; |
| pinctrl-0 = <&ao_cec_pins>; |
| pinctrl-names = "default"; |
| hdmi-phandle = <&hdmi_tx>; |
| }; |
| |
| ðmac { |
| status = "okay"; |
| pinctrl-0 = <ð_rgmii_pins>; |
| pinctrl-names = "default"; |
| |
| phy-handle = <ð_phy0>; |
| phy-mode = "rgmii"; |
| |
| amlogic,tx-delay-ns = <2>; |
| |
| mdio { |
| compatible = "snps,dwmac-mdio"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| eth_phy0: ethernet-phy@0 { |
| /* Realtek RTL8211F (0x001cc916) */ |
| reg = <0>; |
| |
| reset-assert-us = <10000>; |
| reset-deassert-us = <80000>; |
| reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; |
| |
| interrupt-parent = <&gpio_intc>; |
| /* MAC_INTR on GPIOZ_15 */ |
| interrupts = <29 IRQ_TYPE_LEVEL_LOW>; |
| }; |
| }; |
| }; |
| |
| &hdmi_tx { |
| status = "okay"; |
| pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>; |
| pinctrl-names = "default"; |
| }; |
| |
| &hdmi_tx_tmds_port { |
| hdmi_tx_tmds_out: endpoint { |
| remote-endpoint = <&hdmi_connector_in>; |
| }; |
| }; |
| |
| &ir { |
| status = "okay"; |
| pinctrl-0 = <&remote_input_ao_pins>; |
| pinctrl-names = "default"; |
| linux,rc-map-name = "rc-vega-s9x"; |
| }; |
| |
| &pwm_ef { |
| status = "okay"; |
| pinctrl-0 = <&pwm_e_pins>; |
| pinctrl-names = "default"; |
| clocks = <&clkc CLKID_FCLK_DIV4>; |
| clock-names = "clkin0"; |
| }; |
| |
| &saradc { |
| status = "okay"; |
| vref-supply = <&vddio_ao18>; |
| }; |
| |
| /* Wireless SDIO Module */ |
| &sd_emmc_a { |
| status = "okay"; |
| pinctrl-0 = <&sdio_pins>; |
| pinctrl-1 = <&sdio_clk_gate_pins>; |
| pinctrl-names = "default", "clk-gate"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| bus-width = <4>; |
| cap-sd-highspeed; |
| max-frequency = <50000000>; |
| |
| non-removable; |
| disable-wp; |
| |
| /* WiFi firmware requires power to be kept while in suspend */ |
| keep-power-in-suspend; |
| |
| mmc-pwrseq = <&sdio_pwrseq>; |
| |
| vmmc-supply = <&vddao_3v3>; |
| vqmmc-supply = <&vddio_boot>; |
| |
| brcmf: wifi@1 { |
| reg = <1>; |
| compatible = "brcm,bcm4329-fmac"; |
| }; |
| }; |
| |
| /* SD card */ |
| &sd_emmc_b { |
| status = "okay"; |
| pinctrl-0 = <&sdcard_pins>; |
| pinctrl-1 = <&sdcard_clk_gate_pins>; |
| pinctrl-names = "default", "clk-gate"; |
| |
| bus-width = <4>; |
| cap-sd-highspeed; |
| max-frequency = <50000000>; |
| disable-wp; |
| |
| cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>; |
| |
| vmmc-supply = <&vddao_3v3>; |
| vqmmc-supply = <&vcc_3v3>; |
| }; |
| |
| /* eMMC */ |
| &sd_emmc_c { |
| status = "okay"; |
| pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>; |
| pinctrl-1 = <&emmc_clk_gate_pins>; |
| pinctrl-names = "default", "clk-gate"; |
| |
| bus-width = <8>; |
| cap-mmc-highspeed; |
| max-frequency = <200000000>; |
| non-removable; |
| disable-wp; |
| mmc-ddr-1_8v; |
| mmc-hs200-1_8v; |
| |
| mmc-pwrseq = <&emmc_pwrseq>; |
| vmmc-supply = <&vcc_3v3>; |
| vqmmc-supply = <&vddio_boot>; |
| }; |
| |
| /* This is connected to the Bluetooth module: */ |
| &uart_A { |
| status = "okay"; |
| pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>; |
| pinctrl-names = "default"; |
| |
| bluetooth { |
| compatible = "brcm,bcm43438-bt"; |
| shutdown-gpios = <&gpio GPIOX_20 GPIO_ACTIVE_HIGH>; |
| max-speed = <2000000>; |
| clocks = <&wifi32k>; |
| clock-names = "lpo"; |
| }; |
| }; |
| |
| /* This UART is brought out to the DB9 connector */ |
| &uart_AO { |
| status = "okay"; |
| pinctrl-0 = <&uart_ao_a_pins>; |
| pinctrl-names = "default"; |
| }; |
| |
| &usb0_phy { |
| status = "okay"; |
| phy-supply = <&usb_pwr>; |
| }; |
| |
| &usb1_phy { |
| status = "okay"; |
| }; |
| |
| &usb0 { |
| status = "okay"; |
| }; |
| |
| &usb1 { |
| status = "okay"; |
| }; |