| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Copyright (c) 2022, Lux Aliaga <they@mint.lgbt> |
| */ |
| |
| /dts-v1/; |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/input/gpio-keys.h> |
| #include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| #include "sm6125.dtsi" |
| #include "pm6125.dtsi" |
| |
| / { |
| model = "Xiaomi Mi A3"; |
| compatible = "xiaomi,laurel-sprout", "qcom,sm6125"; |
| chassis-type = "handset"; |
| |
| /* required for bootloader to select correct board */ |
| qcom,msm-id = <394 0>; /* sm6125 v1 */ |
| qcom,board-id = <11 0>; |
| |
| chosen { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| framebuffer0: framebuffer@5c000000 { |
| compatible = "simple-framebuffer"; |
| reg = <0 0x5c000000 0 (1560 * 720 * 4)>; |
| width = <720>; |
| height = <1560>; |
| stride = <(720 * 4)>; |
| format = "a8r8g8b8"; |
| }; |
| }; |
| |
| reserved-memory { |
| debug_mem: debug@ffb00000 { |
| reg = <0x0 0xffb00000 0x0 0xc0000>; |
| no-map; |
| }; |
| |
| last_log_mem: lastlog@ffbc0000 { |
| reg = <0x0 0xffbc0000 0x0 0x80000>; |
| no-map; |
| }; |
| |
| pstore_mem: ramoops@ffc00000 { |
| compatible = "ramoops"; |
| reg = <0x0 0xffc40000 0x0 0xc0000>; |
| record-size = <0x1000>; |
| console-size = <0x40000>; |
| pmsg-size = <0x20000>; |
| }; |
| |
| cmdline_mem: memory@ffd00000 { |
| reg = <0x0 0xffd40000 0x0 0x1000>; |
| no-map; |
| }; |
| }; |
| |
| extcon_usb: usb-id { |
| compatible = "linux,extcon-usb-gpio"; |
| id-gpios = <&tlmm 102 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| pinctrl-0 = <&vol_up_n>; |
| pinctrl-names = "default"; |
| |
| key-volume-up { |
| label = "Volume Up"; |
| gpios = <&pm6125_gpios 5 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_VOLUMEUP>; |
| debounce-interval = <15>; |
| linux,can-disable; |
| wakeup-source; |
| }; |
| }; |
| |
| thermal-zones { |
| rf-pa0-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&pm6125_adc_tm 0>; |
| |
| trips { |
| active-config0 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| quiet-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <5000>; |
| thermal-sensors = <&pm6125_adc_tm 1>; |
| |
| trips { |
| active-config0 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| xo-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&pm6125_adc_tm 2>; |
| |
| trips { |
| active-config0 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &hsusb_phy1 { |
| vdd-supply = <&vreg_l7a>; |
| vdda-pll-supply = <&vreg_l10a>; |
| vdda-phy-dpdm-supply = <&vreg_l15a>; |
| status = "okay"; |
| }; |
| |
| &pm6125_adc { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&camera_flash_therm &emmc_ufs_therm>; |
| |
| channel@4d { |
| reg = <ADC5_AMUX_THM1_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| label = "rf_pa0_therm"; |
| }; |
| |
| channel@4e { |
| reg = <ADC5_AMUX_THM2_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| label = "quiet_therm"; |
| }; |
| |
| channel@52 { |
| reg = <ADC5_GPIO1_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| label = "camera_flash_therm"; |
| }; |
| |
| channel@54 { |
| reg = <ADC5_GPIO3_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| label = "emmc_ufs_therm"; |
| }; |
| }; |
| |
| &pm6125_adc_tm { |
| status = "okay"; |
| |
| rf-pa0-therm@0 { |
| reg = <0>; |
| io-channels = <&pm6125_adc ADC5_AMUX_THM1_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time-us = <200>; |
| }; |
| |
| quiet-therm@1 { |
| reg = <1>; |
| io-channels = <&pm6125_adc ADC5_AMUX_THM2_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time-us = <200>; |
| }; |
| |
| xo-therm@2 { |
| reg = <2>; |
| io-channels = <&pm6125_adc ADC5_XO_THERM_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time-us = <200>; |
| }; |
| }; |
| |
| &pm6125_gpios { |
| camera_flash_therm: camera-flash-therm-state { |
| pins = "gpio3"; |
| function = PMIC_GPIO_FUNC_NORMAL; |
| bias-high-impedance; |
| }; |
| |
| emmc_ufs_therm: emmc-ufs-therm-state { |
| pins = "gpio6"; |
| function = PMIC_GPIO_FUNC_NORMAL; |
| bias-high-impedance; |
| }; |
| |
| vol_up_n: vol-up-n-state { |
| pins = "gpio5"; |
| function = PMIC_GPIO_FUNC_NORMAL; |
| input-enable; |
| bias-pull-up; |
| }; |
| }; |
| |
| &pon_pwrkey { |
| status = "okay"; |
| }; |
| |
| &pon_resin { |
| linux,code = <KEY_VOLUMEDOWN>; |
| status = "okay"; |
| }; |
| |
| &rpm_requests { |
| regulators-0 { |
| compatible = "qcom,rpm-pm6125-regulators"; |
| |
| vreg_s6a: s6 { |
| regulator-min-microvolt = <936000>; |
| regulator-max-microvolt = <1422000>; |
| }; |
| |
| vreg_l1a: l1 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1256000>; |
| }; |
| |
| vreg_l2a: l2 { |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1056000>; |
| }; |
| |
| vreg_l3a: l3 { |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1064000>; |
| }; |
| |
| vreg_l4a: l4 { |
| regulator-min-microvolt = <872000>; |
| regulator-max-microvolt = <976000>; |
| regulator-allow-set-load; |
| }; |
| |
| vreg_l5a: l5 { |
| regulator-min-microvolt = <1648000>; |
| regulator-max-microvolt = <2950000>; |
| regulator-allow-set-load; |
| }; |
| |
| vreg_l6a: l6 { |
| regulator-min-microvolt = <576000>; |
| regulator-max-microvolt = <656000>; |
| }; |
| |
| vreg_l7a: l7 { |
| regulator-min-microvolt = <872000>; |
| regulator-max-microvolt = <976000>; |
| }; |
| |
| vreg_l8a: l8 { |
| regulator-min-microvolt = <400000>; |
| regulator-max-microvolt = <728000>; |
| }; |
| |
| vreg_l9a: l9 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1896000>; |
| }; |
| |
| vreg_l10a: l10 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1896000>; |
| regulator-allow-set-load; |
| }; |
| |
| vreg_l11a: l11 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1952000>; |
| regulator-allow-set-load; |
| }; |
| |
| vreg_l12a: l12 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1996000>; |
| }; |
| |
| vreg_l13a: l13 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1832000>; |
| }; |
| |
| vreg_l14a: l14 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1904000>; |
| }; |
| |
| vreg_l15a: l15 { |
| regulator-min-microvolt = <3104000>; |
| regulator-max-microvolt = <3232000>; |
| }; |
| |
| vreg_l16a: l16 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1904000>; |
| }; |
| |
| vreg_l17a: l17 { |
| regulator-min-microvolt = <1248000>; |
| regulator-max-microvolt = <1304000>; |
| }; |
| |
| vreg_l18a: l18 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1264000>; |
| regulator-allow-set-load; |
| }; |
| |
| vreg_l19a: l19 { |
| regulator-min-microvolt = <1648000>; |
| regulator-max-microvolt = <2952000>; |
| }; |
| |
| vreg_l20a: l20 { |
| regulator-min-microvolt = <1648000>; |
| regulator-max-microvolt = <2952000>; |
| }; |
| |
| vreg_l21a: l21 { |
| regulator-min-microvolt = <2600000>; |
| regulator-max-microvolt = <2856000>; |
| }; |
| |
| vreg_l22a: l22 { |
| regulator-min-microvolt = <2944000>; |
| regulator-max-microvolt = <2950000>; |
| regulator-allow-set-load; |
| }; |
| |
| vreg_l23a: l23 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3400000>; |
| }; |
| |
| vreg_l24a: l24 { |
| regulator-min-microvolt = <2944000>; |
| regulator-max-microvolt = <2950000>; |
| regulator-allow-set-load; |
| }; |
| }; |
| }; |
| |
| &sdc2_off_state { |
| sd-cd-pins { |
| pins = "gpio98"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| &sdc2_on_state { |
| sd-cd-pins { |
| pins = "gpio98"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| }; |
| |
| &sdhc_2 { |
| cd-gpios = <&tlmm 98 GPIO_ACTIVE_HIGH>; |
| vmmc-supply = <&vreg_l22a>; |
| vqmmc-supply = <&vreg_l5a>; |
| no-sdio; |
| no-mmc; |
| status = "okay"; |
| }; |
| |
| &tlmm { |
| gpio-reserved-ranges = <22 2>, <28 6>; |
| }; |
| |
| &ufs_mem_hc { |
| vcc-supply = <&vreg_l24a>; |
| vccq2-supply = <&vreg_l11a>; |
| vcc-max-microamp = <600000>; |
| vccq2-max-microamp = <600000>; |
| vdd-hba-supply = <&vreg_l18a>; |
| status = "okay"; |
| }; |
| |
| &ufs_mem_phy { |
| vdda-phy-supply = <&vreg_l4a>; |
| vdda-pll-supply = <&vreg_l10a>; |
| status = "okay"; |
| }; |
| |
| &usb3 { |
| status = "okay"; |
| }; |
| |
| &usb3_dwc3 { |
| extcon = <&extcon_usb>; |
| }; |