configs: at91: Remove CONFIG_SYS_EXTRA_OPTIONS assignment
To remove the assignment of CONFIG_SYS_EXTRA_OPTIONS option,
which is deprecated, use the CONFIG_XXXX_BOOT options to
indicate the boot media, and the SoC is selected by the board.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
diff --git a/include/configs/at91-sama5_common.h b/include/configs/at91-sama5_common.h
index 435c7df..dc36c2a 100644
--- a/include/configs/at91-sama5_common.h
+++ b/include/configs/at91-sama5_common.h
@@ -42,7 +42,7 @@
* Command line configuration.
*/
-#ifdef CONFIG_SYS_USE_MMC
+#ifdef CONFIG_SD_BOOT
#ifdef CONFIG_ENV_IS_IN_MMC
/* Use raw reserved sectors to save environment */
@@ -63,7 +63,7 @@
#else
-#ifdef CONFIG_SYS_USE_NANDFLASH
+#ifdef CONFIG_NAND_BOOT
/* u-boot env in nand flash */
#define CONFIG_ENV_OFFSET 0xc0000
#define CONFIG_ENV_OFFSET_REDUND 0x100000
@@ -71,7 +71,7 @@
#define CONFIG_BOOTCOMMAND "nand read 0x21000000 0x180000 0x80000;" \
"nand read 0x22000000 0x200000 0x600000;" \
"bootz 0x22000000 - 0x21000000"
-#elif CONFIG_SYS_USE_SERIALFLASH
+#elif CONFIG_SPI_BOOT
/* u-boot env in serial flash, by default is bus 0 and cs 0 */
#define CONFIG_ENV_OFFSET 0x6000
#define CONFIG_ENV_SIZE 0x2000
diff --git a/include/configs/at91sam9m10g45ek.h b/include/configs/at91sam9m10g45ek.h
index 36acaa5..2957da9 100644
--- a/include/configs/at91sam9m10g45ek.h
+++ b/include/configs/at91sam9m10g45ek.h
@@ -80,7 +80,7 @@
#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_MEMTEST_END 0x23e00000
-#ifdef CONFIG_SYS_USE_NANDFLASH
+#ifdef CONFIG_NAND_BOOT
/* bootstrap + u-boot + env in nandflash */
#define CONFIG_ENV_OFFSET 0x120000
#define CONFIG_ENV_OFFSET_REDUND 0x100000
@@ -89,7 +89,7 @@
#define CONFIG_BOOTCOMMAND \
"nand read 0x70000000 0x200000 0x300000;" \
"bootm 0x70000000"
-#elif CONFIG_SYS_USE_MMC
+#elif CONFIG_SD_BOOT
/* bootstrap + u-boot + env + linux in mmc */
#define CONFIG_ENV_SIZE 0x4000
@@ -115,7 +115,7 @@
#define CONFIG_SYS_MONITOR_LEN 0x80000
-#ifdef CONFIG_SYS_USE_MMC
+#ifdef CONFIG_SD_BOOT
#define CONFIG_SPL_BSS_START_ADDR 0x70000000
#define CONFIG_SPL_BSS_MAX_SIZE 0x00080000
@@ -125,7 +125,7 @@
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
-#elif CONFIG_SYS_USE_NANDFLASH
+#elif CONFIG_NAND_BOOT
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_BASE
#define CONFIG_SPL_NAND_ECC
diff --git a/include/configs/at91sam9n12ek.h b/include/configs/at91sam9n12ek.h
index c9adcf9..111a7dc 100644
--- a/include/configs/at91sam9n12ek.h
+++ b/include/configs/at91sam9n12ek.h
@@ -108,7 +108,7 @@
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 1
#endif
-#ifdef CONFIG_SYS_USE_SPIFLASH
+#ifdef CONFIG_SPI_BOOT
/* bootstrap + u-boot + env + linux in dataflash on CS0 */
#define CONFIG_ENV_OFFSET 0x5000
@@ -119,7 +119,7 @@
"sf probe 0; sf read 0x22000000 0x100000 0x300000; " \
"bootm 0x22000000"
-#elif defined(CONFIG_SYS_USE_NANDFLASH)
+#elif defined(CONFIG_NAND_BOOT)
/* bootstrap + u-boot + env + linux in nandflash */
#define CONFIG_ENV_OFFSET 0x120000
@@ -131,7 +131,7 @@
"nand read 0x22000000 0x200000 0x400000;" \
"bootm 0x22000000 - 0x21000000"
-#else /* CONFIG_SYS_USE_MMC */
+#else /* CONFIG_SD_BOOT */
/* bootstrap + u-boot + env + linux in mmc */
@@ -180,13 +180,19 @@
#define CONFIG_SYS_MCKR 0x1301
#define CONFIG_SYS_MCKR_CSS 0x1302
-#ifdef CONFIG_SYS_USE_MMC
+#ifdef CONFIG_SD_BOOT
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
#elif CONFIG_SYS_USE_NANDFLASH
+#elif CONFIG_SPI_BOOT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x8400
+
+#elif CONFIG_NAND_BOOT
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_BASE
+#endif
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_SIZE 0x800
@@ -196,10 +202,4 @@
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0
#define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER
-#elif CONFIG_SYS_USE_SPIFLASH
-#define CONFIG_SPL_SPI_LOAD
-#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x8400
-
-#endif
-
#endif
diff --git a/include/configs/at91sam9x5ek.h b/include/configs/at91sam9x5ek.h
index eb79844..1d4971c 100644
--- a/include/configs/at91sam9x5ek.h
+++ b/include/configs/at91sam9x5ek.h
@@ -15,8 +15,6 @@
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* 12 MHz crystal */
-#define CONFIG_AT91SAM9X5EK
-
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
@@ -102,7 +100,7 @@
#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_MEMTEST_END 0x26e00000
-#ifdef CONFIG_SYS_USE_NANDFLASH
+#ifdef CONFIG_NAND_BOOT
/* bootstrap + u-boot + env + linux in nandflash */
#define CONFIG_ENV_OFFSET 0x120000
#define CONFIG_ENV_OFFSET_REDUND 0x100000
@@ -110,7 +108,7 @@
#define CONFIG_BOOTCOMMAND "nand read " \
"0x22000000 0x200000 0x300000; " \
"bootm 0x22000000"
-#elif defined(CONFIG_SYS_USE_SPIFLASH)
+#elif defined(CONFIG_SPI_BOOT)
/* bootstrap + u-boot + env + linux in spi flash */
#define CONFIG_ENV_OFFSET 0x5000
#define CONFIG_ENV_SIZE 0x3000
@@ -128,7 +126,7 @@
#define CONFIG_BOOTCOMMAND "sf probe 0; " \
"sf read 0x22000000 0x84000 0x294000; " \
"bootm 0x22000000"
-#else /* CONFIG_SYS_USE_MMC */
+#else /* CONFIG_SD_BOOT */
/* bootstrap + u-boot + env + linux in mmc */
#define CONFIG_ENV_SIZE 0x4000
#endif
@@ -160,13 +158,18 @@
#define CONFIG_SYS_MCKR 0x1301
#define CONFIG_SYS_MCKR_CSS 0x1302
-#ifdef CONFIG_SYS_USE_MMC
+#ifdef CONFIG_SD_BOOT
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
-#elif CONFIG_SYS_USE_NANDFLASH
+#elif CONFIG_SPI_BOOT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x8400
+
+#elif CONFIG_NAND_BOOT
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_BASE
+#endif
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_SIZE 0x800
@@ -176,10 +179,4 @@
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0
#define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER
-#elif CONFIG_SYS_USE_SPIFLASH
-#define CONFIG_SPL_SPI_LOAD
-#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x8400
-
-#endif
-
#endif
diff --git a/include/configs/sama5d2_ptc.h b/include/configs/sama5d2_ptc.h
index 75a81f1..3ae16df 100644
--- a/include/configs/sama5d2_ptc.h
+++ b/include/configs/sama5d2_ptc.h
@@ -72,7 +72,7 @@
#define CONFIG_NET_RETRY_COUNT 20
#define CONFIG_MACB_SEARCH_PHY
-#ifdef CONFIG_SYS_USE_NANDFLASH
+#ifdef CONFIG_NAND_BOOT
#undef CONFIG_ENV_OFFSET
#undef CONFIG_ENV_OFFSET_REDUND
#undef CONFIG_BOOTCOMMAND
@@ -95,13 +95,14 @@
#define CONFIG_SYS_MONITOR_LEN (512 << 10)
-#ifdef CONFIG_SYS_USE_SERIALFLASH
+#ifdef CONFIG_SPI_BOOT
#define CONFIG_SPL_SPI_LOAD
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x8000
-#elif CONFIG_SYS_USE_NANDFLASH
+#elif CONFIG_NAND_BOOT
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_BASE
+#endif
#define CONFIG_PMECC_CAP 8
#define CONFIG_PMECC_SECTOR_SIZE 512
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000
@@ -112,6 +113,5 @@
#define CONFIG_SYS_NAND_BLOCK_SIZE 0x40000
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0
#define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER
-#endif
#endif
diff --git a/include/configs/sama5d2_xplained.h b/include/configs/sama5d2_xplained.h
index 7b75413..4f24a56 100644
--- a/include/configs/sama5d2_xplained.h
+++ b/include/configs/sama5d2_xplained.h
@@ -47,7 +47,7 @@
#define CONFIG_ATMEL_LCD_RGB565
#endif
-#ifdef CONFIG_SYS_USE_MMC
+#ifdef CONFIG_SD_BOOT
/* bootstrap + u-boot + env in sd card */
#undef CONFIG_BOOTCOMMAND
@@ -69,11 +69,11 @@
#define CONFIG_SYS_MONITOR_LEN (512 << 10)
-#ifdef CONFIG_SYS_USE_MMC
+#ifdef CONFIG_SD_BOOT
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
-#elif CONFIG_SYS_USE_SERIALFLASH
+#elif CONFIG_SPI_BOOT
#define CONFIG_SPL_SPI_LOAD
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x10000
diff --git a/include/configs/sama5d3_xplained.h b/include/configs/sama5d3_xplained.h
index 54ea98d..a6697cd 100644
--- a/include/configs/sama5d3_xplained.h
+++ b/include/configs/sama5d3_xplained.h
@@ -69,12 +69,6 @@
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
-#if CONFIG_SYS_USE_NANDFLASH
-/* override the bootcmd, bootargs and other configuration for nandflash env */
-#elif CONFIG_SYS_USE_MMC
-/* override the bootcmd, bootargs and other configuration for sd/mmc env */
-#endif
-
/* SPL */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE 0x300000
@@ -86,13 +80,14 @@
#define CONFIG_SYS_MONITOR_LEN (512 << 10)
-#ifdef CONFIG_SYS_USE_MMC
+#ifdef CONFIG_SD_BOOT
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
-#elif CONFIG_SYS_USE_NANDFLASH
+#elif CONFIG_NAND_BOOT
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_BASE
+#endif
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_SIZE 0x800
@@ -103,5 +98,3 @@
#define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER
#endif
-
-#endif
diff --git a/include/configs/sama5d3xek.h b/include/configs/sama5d3xek.h
index a7223e2..bd93a1e 100644
--- a/include/configs/sama5d3xek.h
+++ b/include/configs/sama5d3xek.h
@@ -98,14 +98,6 @@
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
-#ifdef CONFIG_SYS_USE_SERIALFLASH
-/* override the bootcmd, bootargs and other configuration for spi flash env*/
-#elif CONFIG_SYS_USE_NANDFLASH
-/* override the bootcmd, bootargs and other configuration nandflash env */
-#elif CONFIG_SYS_USE_MMC
-/* override the bootcmd, bootargs and other configuration for sd/mmc env */
-#endif
-
/* SPL */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE 0x300000
@@ -117,13 +109,18 @@
#define CONFIG_SYS_MONITOR_LEN (512 << 10)
-#ifdef CONFIG_SYS_USE_MMC
+#ifdef CONFIG_SD_BOOT
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
-#elif CONFIG_SYS_USE_NANDFLASH
+#elif CONFIG_SPI_BOOT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x10000
+
+#elif CONFIG_NAND_BOOT
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_BASE
+#endif
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_SIZE 0x800
@@ -133,10 +130,4 @@
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0
#define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER
-#elif CONFIG_SYS_USE_SERIALFLASH
-#define CONFIG_SPL_SPI_LOAD
-#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x10000
-
-#endif
-
#endif
diff --git a/include/configs/sama5d4_xplained.h b/include/configs/sama5d4_xplained.h
index f48ef40..5dc5e7d 100644
--- a/include/configs/sama5d4_xplained.h
+++ b/include/configs/sama5d4_xplained.h
@@ -58,14 +58,6 @@
#define CONFIG_ATMEL_LCD_RGB565
#endif
-#ifdef CONFIG_SYS_USE_SERIALFLASH
-/* override the bootcmd, bootargs and other configuration for spi flash env */
-#elif CONFIG_SYS_USE_NANDFLASH
-/* override the bootcmd, bootargs and other configuration for nandflash env */
-#elif CONFIG_SYS_USE_MMC
-/* override the bootcmd, bootargs and other configuration for sd/mmc env */
-#endif
-
/* SPL */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE 0x200000
@@ -77,13 +69,19 @@
#define CONFIG_SYS_MONITOR_LEN (512 << 10)
-#ifdef CONFIG_SYS_USE_MMC
+#ifdef CONFIG_SD_BOOT
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
#elif CONFIG_SYS_USE_NANDFLASH
+#elif CONFIG_SPI_BOOT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x10000
+
+#elif CONFIG_NAND_BOOT
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_BASE
+#endif
#define CONFIG_PMECC_CAP 8
#define CONFIG_PMECC_SECTOR_SIZE 512
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000
@@ -95,9 +93,4 @@
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0
#define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER
-#elif CONFIG_SYS_USE_SERIALFLASH
-#define CONFIG_SPL_SPI_LOAD
-#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x10000
-
-#endif
#endif
diff --git a/include/configs/sama5d4ek.h b/include/configs/sama5d4ek.h
index 0410d65..94e8e89 100644
--- a/include/configs/sama5d4ek.h
+++ b/include/configs/sama5d4ek.h
@@ -54,14 +54,6 @@
#define CONFIG_ATMEL_HLCD
#define CONFIG_ATMEL_LCD_RGB565
-#ifdef CONFIG_SYS_USE_SERIALFLASH
-/* override the bootcmd, bootargs and other configuration for spi flash env*/
-#elif CONFIG_SYS_USE_NANDFLASH
-/* override the bootcmd, bootargs and other configuration for nandflash env*/
-#elif CONFIG_SYS_USE_MMC
-/* override the bootcmd, bootargs and other configuration for sd/mmc env */
-#endif
-
/* SPL */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE 0x200000
@@ -73,13 +65,18 @@
#define CONFIG_SYS_MONITOR_LEN (512 << 10)
-#ifdef CONFIG_SYS_USE_MMC
+#ifdef CONFIG_SD_BOOT
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
-#elif CONFIG_SYS_USE_NANDFLASH
+#elif CONFIG_SPI_BOOT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x10000
+
+#elif CONFIG_NAND_BOOT
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_BASE
+#endif
#define CONFIG_PMECC_CAP 8
#define CONFIG_PMECC_SECTOR_SIZE 512
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000
@@ -91,9 +88,4 @@
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0
#define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER
-#elif CONFIG_SYS_USE_SERIALFLASH
-#define CONFIG_SPL_SPI_LOAD
-#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x10000
-
-#endif
#endif
diff --git a/include/configs/vinco.h b/include/configs/vinco.h
index 0bd8bbb..aaed815 100644
--- a/include/configs/vinco.h
+++ b/include/configs/vinco.h
@@ -78,7 +78,7 @@
#define CONFIG_NET_RETRY_COUNT 20
#define CONFIG_MACB_SEARCH_PHY
-#ifdef CONFIG_SYS_USE_SERIALFLASH
+#ifdef CONFIG_SPI_BOOT
/* bootstrap + u-boot + env + linux in serial flash */
#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS
#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS