bosch: Add initial board support for ACC
The Bosch ACC (Air Center Control) Board is based on the i.MX6D.
The device tree is copied from Linux, see [1]. The only difference
compared to the Linux DT is the removal of usbphynop properties. They are
defined in the Linux version of imx6qdl.dtsi, but not in the u-boot
version.
[1] Commit 6192cf8ac082 from
git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux.git
Signed-off-by: Philip Oberfichtner <pro@denx.de>
diff --git a/configs/imx6q_bosch_acc_defconfig b/configs/imx6q_bosch_acc_defconfig
new file mode 100644
index 0000000..3c02f0f
--- /dev/null
+++ b/configs/imx6q_bosch_acc_defconfig
@@ -0,0 +1,110 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_SYS_TEXT_BASE=0x17780000
+CONFIG_SYS_MALLOC_LEN=0x01000000
+CONFIG_SYS_MALLOC_F_LEN=0x9000
+CONFIG_SPL_GPIO=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_ENV_SIZE=0x1000
+CONFIG_ENV_OFFSET=0x1fe000
+CONFIG_MX6QDL=y
+CONFIG_MX6_DDRCAL=y
+CONFIG_TARGET_MX6Q_ACC=y
+CONFIG_DEFAULT_DEVICE_TREE="imx6q-bosch-acc"
+CONFIG_SPL_TEXT_BASE=0x00908000
+CONFIG_SPL_MMC=y
+CONFIG_SPL_SERIAL=y
+CONFIG_SPL_DRIVERS_MISC=y
+CONFIG_BOOTCOUNT_BOOTLIMIT=8
+CONFIG_SPL_SIZE_LIMIT=69632
+CONFIG_SPL=y
+CONFIG_ENV_OFFSET_REDUND=0x1ff000
+CONFIG_IMX_HAB=y
+# CONFIG_CMD_BMODE is not set
+# CONFIG_CMD_DEKBLOB is not set
+CONFIG_BUILD_TARGET=""
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_FIT=y
+CONFIG_FIT_SIGNATURE=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_SHOW_BOOT_PROGRESS=y
+CONFIG_USE_BOOTCOMMAND=y
+CONFIG_BOOTCOMMAND="run mmc_mmc_fit"
+CONFIG_SPL_BOARD_INIT=y
+CONFIG_SPL_RAW_IMAGE_SUPPORT=y
+CONFIG_SPL_SEPARATE_BSS=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0xaa
+# CONFIG_SPL_CRC32 is not set
+# CONFIG_SPL_CRYPTO is not set
+CONFIG_SPL_WATCHDOG=y
+CONFIG_HUSH_PARSER=y
+# CONFIG_CMD_BDI is not set
+# CONFIG_CMD_CONSOLE is not set
+# CONFIG_CMD_BOOTD is not set
+# CONFIG_CMD_ELF is not set
+# CONFIG_CMD_FDT is not set
+# CONFIG_CMD_GO is not set
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_EXPORTENV is not set
+# CONFIG_CMD_IMPORTENV is not set
+# CONFIG_CMD_ENV_EXISTS is not set
+# CONFIG_CMD_CRC32 is not set
+# CONFIG_CMD_MEMORY is not set
+# CONFIG_CMD_FUSE is not set
+# CONFIG_CMD_LOADB is not set
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PART=y
+# CONFIG_CMD_PINMUX is not set
+# CONFIG_CMD_ECHO is not set
+# CONFIG_CMD_ITEST is not set
+# CONFIG_CMD_SOURCE is not set
+# CONFIG_CMD_SETEXPR is not set
+# CONFIG_CMD_NET is not set
+# CONFIG_CMD_BLOCK_CACHE is not set
+# CONFIG_CMD_SLEEP is not set
+# CONFIG_CMD_MP is not set
+# CONFIG_CMD_HASH is not set
+CONFIG_CMD_EXT4=y
+CONFIG_DOS_PARTITION=y
+CONFIG_EFI_PARTITION=y
+# CONFIG_SPL_EFI_PARTITION is not set
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_MULTI_DTB_FIT=y
+CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clocks clock-names interrupt-parent"
+CONFIG_ENV_OVERWRITE=y
+CONFIG_ENV_IS_NOWHERE=y
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
+CONFIG_SYS_MMC_ENV_PART=1
+CONFIG_ENV_APPEND=y
+CONFIG_ENV_WRITEABLE_LIST=y
+CONFIG_ENV_ACCESS_IGNORE_FORCE=y
+CONFIG_VERSION_VARIABLE=y
+CONFIG_TFTP_BLOCKSIZE=512
+CONFIG_SPL_DM=y
+CONFIG_BOOTCOUNT_LIMIT=y
+CONFIG_DM_BOOTCOUNT=y
+CONFIG_DM_BOOTCOUNT_PMIC_PFUZE100=y
+CONFIG_SYS_I2C_MXC=y
+CONFIG_SUPPORT_EMMC_BOOT=y
+CONFIG_FSL_USDHC=y
+CONFIG_PHYLIB=y
+CONFIG_FEC_MXC=y
+CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_PMIC_PFUZE100=y
+CONFIG_DM_SERIAL=y
+CONFIG_MXC_UART=y
+CONFIG_WATCHDOG_TIMEOUT_MSECS=60000
+CONFIG_IMX_WATCHDOG=y
+CONFIG_WDT=y
+CONFIG_EXT4_WRITE=y
+CONFIG_FS_FAT=y
+CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED=y
+# CONFIG_EFI_LOADER is not set