u_qe: add u_qe_upload_firmware for u_qe
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
diff --git a/drivers/qe/qe.c b/drivers/qe/qe.c
index b545ec9..bc94673 100644
--- a/drivers/qe/qe.c
+++ b/drivers/qe/qe.c
@@ -188,7 +188,7 @@
uint qe_base = CONFIG_SYS_IMMR + 0x01400000; /* QE immr base */
qe_immr = (qe_map_t *)qe_base;
- qe_upload_firmware((const void *)CONFIG_SYS_QE_FW_ADDR);
+ u_qe_upload_firmware((const void *)CONFIG_SYS_QE_FW_ADDR);
out_be32(&qe_immr->iram.iready, QE_IRAM_READY);
}
#endif
@@ -444,6 +444,131 @@
return 0;
}
+#ifdef CONFIG_U_QE
+/*
+ * Upload a microcode to the I-RAM at a specific address.
+ *
+ * See docs/README.qe_firmware for information on QE microcode uploading.
+ *
+ * Currently, only version 1 is supported, so the 'version' field must be
+ * set to 1.
+ *
+ * The SOC model and revision are not validated, they are only displayed for
+ * informational purposes.
+ *
+ * 'calc_size' is the calculated size, in bytes, of the firmware structure and
+ * all of the microcode structures, minus the CRC.
+ *
+ * 'length' is the size that the structure says it is, including the CRC.
+ */
+int u_qe_upload_firmware(const struct qe_firmware *firmware)
+{
+ unsigned int i;
+ unsigned int j;
+ u32 crc;
+ size_t calc_size = sizeof(struct qe_firmware);
+ size_t length;
+ const struct qe_header *hdr;
+#ifdef CONFIG_DEEP_SLEEP
+ ccsr_gur_t __iomem *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+#endif
+ if (!firmware) {
+ printf("Invalid address\n");
+ return -EINVAL;
+ }
+
+ hdr = &firmware->header;
+ length = be32_to_cpu(hdr->length);
+
+ /* Check the magic */
+ if ((hdr->magic[0] != 'Q') || (hdr->magic[1] != 'E') ||
+ (hdr->magic[2] != 'F')) {
+ printf("Not a microcode\n");
+#ifdef CONFIG_DEEP_SLEEP
+ setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_QE_DISABLE);
+#endif
+ return -EPERM;
+ }
+
+ /* Check the version */
+ if (hdr->version != 1) {
+ printf("Unsupported version\n");
+ return -EPERM;
+ }
+
+ /* Validate some of the fields */
+ if ((firmware->count < 1) || (firmware->count > MAX_QE_RISC)) {
+ printf("Invalid data\n");
+ return -EINVAL;
+ }
+
+ /* Validate the length and check if there's a CRC */
+ calc_size += (firmware->count - 1) * sizeof(struct qe_microcode);
+
+ for (i = 0; i < firmware->count; i++)
+ /*
+ * For situations where the second RISC uses the same microcode
+ * as the first, the 'code_offset' and 'count' fields will be
+ * zero, so it's okay to add those.
+ */
+ calc_size += sizeof(u32) *
+ be32_to_cpu(firmware->microcode[i].count);
+
+ /* Validate the length */
+ if (length != calc_size + sizeof(u32)) {
+ printf("Invalid length\n");
+ return -EPERM;
+ }
+
+ /*
+ * Validate the CRC. We would normally call crc32_no_comp(), but that
+ * function isn't available unless you turn on JFFS support.
+ */
+ crc = be32_to_cpu(*(u32 *)((void *)firmware + calc_size));
+ if (crc != (crc32(-1, (const void *)firmware, calc_size) ^ -1)) {
+ printf("Firmware CRC is invalid\n");
+ return -EIO;
+ }
+
+ /*
+ * If the microcode calls for it, split the I-RAM.
+ */
+ if (!firmware->split) {
+ out_be16(&qe_immr->cp.cercr,
+ in_be16(&qe_immr->cp.cercr) | QE_CP_CERCR_CIR);
+ }
+
+ if (firmware->soc.model)
+ printf("Firmware '%s' for %u V%u.%u\n",
+ firmware->id, be16_to_cpu(firmware->soc.model),
+ firmware->soc.major, firmware->soc.minor);
+ else
+ printf("Firmware '%s'\n", firmware->id);
+
+ /* Loop through each microcode. */
+ for (i = 0; i < firmware->count; i++) {
+ const struct qe_microcode *ucode = &firmware->microcode[i];
+
+ /* Upload a microcode if it's present */
+ if (ucode->code_offset)
+ qe_upload_microcode(firmware, ucode);
+
+ /* Program the traps for this processor */
+ for (j = 0; j < 16; j++) {
+ u32 trap = be32_to_cpu(ucode->traps[j]);
+
+ if (trap)
+ out_be32(&qe_immr->rsp[i].tibcr[j], trap);
+ }
+
+ /* Enable traps */
+ out_be32(&qe_immr->rsp[i].eccr, be32_to_cpu(ucode->eccr));
+ }
+
+ return 0;
+}
+#endif
+
struct qe_firmware_info *qe_get_firmware_info(void)
{
return qe_firmware_uploaded ? &qe_firmware_info : NULL;