armv8: lx2160ardb : Add support for LX2160ARDB platform
LX2160ARDB is an evaluation board that supports LX2160A
family SoCs. This patch add base support for this board.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
[PK: Sqaush patches from Yinbo Zhu, Peng Ma, Chuanhua Han
and re-arrange defconfig]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
diff --git a/board/freescale/common/qixis.c b/board/freescale/common/qixis.c
index af3dc59..f1b98bc 100644
--- a/board/freescale/common/qixis.c
+++ b/board/freescale/common/qixis.c
@@ -227,8 +227,12 @@
#ifdef QIXIS_LBMAP_SD
QIXIS_WRITE(rst_ctl, 0x30);
QIXIS_WRITE(rcfg_ctl, 0);
+#ifdef NON_EXTENDED_DUTCFG
+ QIXIS_WRITE(dutcfg[0], QIXIS_RCW_SRC_SD);
+#else
set_lbmap(QIXIS_LBMAP_SD);
set_rcw_src(QIXIS_RCW_SRC_SD);
+#endif
QIXIS_WRITE(rcfg_ctl, 0x20);
QIXIS_WRITE(rcfg_ctl, 0x21);
#else
diff --git a/board/freescale/lx2160a/Kconfig b/board/freescale/lx2160a/Kconfig
new file mode 100644
index 0000000..5562c3e
--- /dev/null
+++ b/board/freescale/lx2160a/Kconfig
@@ -0,0 +1,16 @@
+if TARGET_LX2160ARDB
+
+config SYS_BOARD
+ default "lx2160a"
+
+config SYS_VENDOR
+ default "freescale"
+
+config SYS_SOC
+ default "fsl-layerscape"
+
+config SYS_CONFIG_NAME
+ default "lx2160ardb"
+
+source "board/freescale/common/Kconfig"
+endif
diff --git a/board/freescale/lx2160a/MAINTAINERS b/board/freescale/lx2160a/MAINTAINERS
new file mode 100644
index 0000000..aeb7dbc
--- /dev/null
+++ b/board/freescale/lx2160a/MAINTAINERS
@@ -0,0 +1,8 @@
+LX2160ARDB BOARD
+M: Priyanka Jain <priyanka.jain@nxp.com>
+S: Maintained
+F: board/freescale/lx2160a/
+F: include/configs/lx2160a_common.h
+F: include/configs/lx2160ardb.h
+F: configs/lx2160ardb_tfa_defconfig
+F: arch/arm/dts/fsl-lx2160a-rdb.dts
diff --git a/board/freescale/lx2160a/Makefile b/board/freescale/lx2160a/Makefile
new file mode 100644
index 0000000..be3709d
--- /dev/null
+++ b/board/freescale/lx2160a/Makefile
@@ -0,0 +1,9 @@
+#
+# Copyright 2018 Freescale Semiconductor
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += lx2160a.o
+obj-y += ddr.o
+obj-$(CONFIG_TARGET_LX2160ARDB) += eth_lx2160ardb.o
diff --git a/board/freescale/lx2160a/README b/board/freescale/lx2160a/README
new file mode 100644
index 0000000..618c40b
--- /dev/null
+++ b/board/freescale/lx2160a/README
@@ -0,0 +1,79 @@
+Overview
+--------
+The LX2160A Reference Design (RDB) is a high-performance computing,
+evaluation, and development platform that supports the QorIQ LX2160A
+Layerscape Architecture processor and its personalities.
+
+LX2160A SoC Overview
+--------------------------------------
+For details, please refer arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc
+
+LX2160ARDB board Overview
+----------------------
+DDR Memory
+ Two ports of 72-bits (8-bits ECC) DDR4.
+ Each port supports four chip-selects and two DIMM
+ connectors. Data rate upto 3.2 GT/s.
+
+SERDES ports
+ Thress serdes controllers (24 lanes)
+ Serdes1: Supports two USXGMII connectors, each connected through
+ Aquantia AQR107 phy, two 25GbE SFP+ modules connected through an Inphi
+ IN112525 phy and one 40 GbE QSFP+ module connected through an Inphi
+ CS4223 phy.
+
+ Serdes2: Supports one PCIe x4 (Gen1/2/3/4) connector, four SATA 3.0
+ connectors
+
+ Serdes3: Supports one PCIe x8 (Gen1/2/3/4) connector
+
+eSDHC
+ eSDHC1: Supports a SD connector for connecting SD cards
+ eSDHC2: Supports 128GB Micron MTFC128GAJAECE-IT eMMC
+
+Octal SPI (XSPI)
+ Supports two 64 MB onbpard octal SPI flash memories, one SPI emulator
+ for off-board emulation
+
+I2C All system devices on I2C1 multiplexed using PCA9547 multiplexer
+ Serial Ports
+
+USB 3.0
+ Two high speed USB 3.0 ports. First USB 3.0 port configured as
+ Host with Type-A connector, second USB 3.0 port configured as OTG
+ with micro-AB connector
+
+Serial Ports Two UART ports
+Ethernet Two RGMII interfaces
+Debug ARM JTAG support
+
+Booting Options
+---------------
+a) Flexspi boot
+b) SD boot
+
+Memory map for Flexspi flash
+----------------------------
+Image Flash Offset
+bl2_flexspi_nor.pbl (RCW+PBI+bl2.pbl) 0x00000000
+fip.bin (bl31 + bl33(u-boot) +
+ header for Secure-boot(secure-boot only)) 0x00100000
+Boot firmware Environment 0x00500000
+DDR PHY Firmware (fip_ddr_all.bin) 0x00800000
+DPAA2 MC Firmware 0x00A00000
+DPAA2 DPL 0x00D00000
+DPAA2 DPC 0x00E00000
+Kernel.itb 0x01000000
+
+Memory map for sd card
+----------------------------
+Image SD card Offset
+bl2_sd.pbl (RCW+PBI+bl2.pbl) 0x00008
+fip.bin (bl31 + bl33(u-boot) +
+ header for Secure-boot(secure-boot only)) 0x00800
+Boot firmware Environment 0x02800
+DDR PHY Firmware (fip_ddr_all.bin) 0x04000
+DPAA2 MC Firmware 0x05000
+DPAA2 DPL 0x06800
+DPAA2 DPC 0x07000
+Kernel.itb 0x08000
diff --git a/board/freescale/lx2160a/ddr.c b/board/freescale/lx2160a/ddr.c
new file mode 100644
index 0000000..cd422bf
--- /dev/null
+++ b/board/freescale/lx2160a/ddr.c
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2018 NXP
+ */
+
+#include <common.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int fsl_initdram(void)
+{
+ gd->ram_size = tfa_get_dram_size();
+
+ if (!gd->ram_size)
+ gd->ram_size = fsl_ddr_sdram_size();
+
+ return 0;
+}
diff --git a/board/freescale/lx2160a/eth_lx2160ardb.c b/board/freescale/lx2160a/eth_lx2160ardb.c
new file mode 100644
index 0000000..365ff73
--- /dev/null
+++ b/board/freescale/lx2160a/eth_lx2160ardb.c
@@ -0,0 +1,210 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2018 NXP
+ *
+ */
+
+#include <common.h>
+#include <command.h>
+#include <netdev.h>
+#include <malloc.h>
+#include <fsl_mdio.h>
+#include <miiphy.h>
+#include <phy.h>
+#include <fm_eth.h>
+#include <asm/io.h>
+#include <exports.h>
+#include <asm/arch/fsl_serdes.h>
+#include <fsl-mc/fsl_mc.h>
+#include <fsl-mc/ldpaa_wriop.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static bool get_inphi_phy_id(struct mii_dev *bus, int addr, int devad)
+{
+ int phy_reg;
+ u32 phy_id;
+
+ phy_reg = bus->read(bus, addr, devad, MII_PHYSID1);
+ phy_id = (phy_reg & 0xffff) << 16;
+
+ phy_reg = bus->read(bus, addr, devad, MII_PHYSID2);
+ phy_id |= (phy_reg & 0xffff);
+
+ if (phy_id == PHY_UID_IN112525_S03)
+ return true;
+ else
+ return false;
+}
+
+int board_eth_init(bd_t *bis)
+{
+#if defined(CONFIG_FSL_MC_ENET)
+ struct memac_mdio_info mdio_info;
+ struct memac_mdio_controller *reg;
+ int i, interface;
+ struct mii_dev *dev;
+ struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
+ u32 srds_s1;
+
+ srds_s1 = in_le32(&gur->rcwsr[28]) &
+ FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_MASK;
+ srds_s1 >>= FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_SHIFT;
+
+ reg = (struct memac_mdio_controller *)CONFIG_SYS_FSL_WRIOP1_MDIO1;
+ mdio_info.regs = reg;
+ mdio_info.name = DEFAULT_WRIOP_MDIO1_NAME;
+
+ /* Register the EMI 1 */
+ fm_memac_mdio_init(bis, &mdio_info);
+
+ reg = (struct memac_mdio_controller *)CONFIG_SYS_FSL_WRIOP1_MDIO2;
+ mdio_info.regs = reg;
+ mdio_info.name = DEFAULT_WRIOP_MDIO2_NAME;
+
+ /* Register the EMI 2 */
+ fm_memac_mdio_init(bis, &mdio_info);
+
+ dev = miiphy_get_dev_by_name(DEFAULT_WRIOP_MDIO2_NAME);
+ switch (srds_s1) {
+ case 19:
+ wriop_set_phy_address(WRIOP1_DPMAC2, 0,
+ CORTINA_PHY_ADDR1);
+ wriop_set_phy_address(WRIOP1_DPMAC3, 0,
+ AQR107_PHY_ADDR1);
+ wriop_set_phy_address(WRIOP1_DPMAC4, 0,
+ AQR107_PHY_ADDR2);
+ if (get_inphi_phy_id(dev, INPHI_PHY_ADDR1, MDIO_MMD_VEND1)) {
+ wriop_set_phy_address(WRIOP1_DPMAC5, 0,
+ INPHI_PHY_ADDR1);
+ wriop_set_phy_address(WRIOP1_DPMAC6, 0,
+ INPHI_PHY_ADDR1);
+ }
+ wriop_set_phy_address(WRIOP1_DPMAC17, 0,
+ RGMII_PHY_ADDR1);
+ wriop_set_phy_address(WRIOP1_DPMAC18, 0,
+ RGMII_PHY_ADDR2);
+ break;
+
+ case 18:
+ wriop_set_phy_address(WRIOP1_DPMAC7, 0,
+ CORTINA_PHY_ADDR1);
+ wriop_set_phy_address(WRIOP1_DPMAC8, 0,
+ CORTINA_PHY_ADDR1);
+ wriop_set_phy_address(WRIOP1_DPMAC9, 0,
+ CORTINA_PHY_ADDR1);
+ wriop_set_phy_address(WRIOP1_DPMAC10, 0,
+ CORTINA_PHY_ADDR1);
+ wriop_set_phy_address(WRIOP1_DPMAC3, 0,
+ AQR107_PHY_ADDR1);
+ wriop_set_phy_address(WRIOP1_DPMAC4, 0,
+ AQR107_PHY_ADDR2);
+ if (get_inphi_phy_id(dev, INPHI_PHY_ADDR1, MDIO_MMD_VEND1)) {
+ wriop_set_phy_address(WRIOP1_DPMAC5, 0,
+ INPHI_PHY_ADDR1);
+ wriop_set_phy_address(WRIOP1_DPMAC6, 0,
+ INPHI_PHY_ADDR1);
+ }
+ wriop_set_phy_address(WRIOP1_DPMAC17, 0,
+ RGMII_PHY_ADDR1);
+ wriop_set_phy_address(WRIOP1_DPMAC18, 0,
+ RGMII_PHY_ADDR2);
+ break;
+
+ default:
+ printf("SerDes1 protocol 0x%x is not supported on LX2160ARDB\n",
+ srds_s1);
+ goto next;
+ }
+
+ for (i = WRIOP1_DPMAC2; i <= WRIOP1_DPMAC10; i++) {
+ interface = wriop_get_enet_if(i);
+ switch (interface) {
+ case PHY_INTERFACE_MODE_XGMII:
+ dev = miiphy_get_dev_by_name(DEFAULT_WRIOP_MDIO1_NAME);
+ wriop_set_mdio(i, dev);
+ break;
+ case PHY_INTERFACE_MODE_25G_AUI:
+ dev = miiphy_get_dev_by_name(DEFAULT_WRIOP_MDIO2_NAME);
+ wriop_set_mdio(i, dev);
+ break;
+ case PHY_INTERFACE_MODE_XLAUI:
+ dev = miiphy_get_dev_by_name(DEFAULT_WRIOP_MDIO1_NAME);
+ wriop_set_mdio(i, dev);
+ break;
+ default:
+ break;
+ }
+ }
+ for (i = WRIOP1_DPMAC17; i <= WRIOP1_DPMAC18; i++) {
+ interface = wriop_get_enet_if(i);
+ switch (interface) {
+ case PHY_INTERFACE_MODE_RGMII:
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ dev = miiphy_get_dev_by_name(DEFAULT_WRIOP_MDIO1_NAME);
+ wriop_set_mdio(i, dev);
+ break;
+ default:
+ break;
+ }
+ }
+
+next:
+ cpu_eth_init(bis);
+#endif /* CONFIG_FSL_MC_ENET */
+
+#ifdef CONFIG_PHY_AQUANTIA
+ /*
+ * Export functions to be used by AQ firmware
+ * upload application
+ */
+ gd->jt->strcpy = strcpy;
+ gd->jt->mdelay = mdelay;
+ gd->jt->mdio_get_current_dev = mdio_get_current_dev;
+ gd->jt->phy_find_by_mask = phy_find_by_mask;
+ gd->jt->mdio_phydev_for_ethname = mdio_phydev_for_ethname;
+ gd->jt->miiphy_set_current_dev = miiphy_set_current_dev;
+#endif
+ return pci_eth_init(bis);
+}
+
+#if defined(CONFIG_RESET_PHY_R)
+void reset_phy(void)
+{
+#if defined(CONFIG_FSL_MC_ENET)
+ mc_env_boot();
+#endif
+}
+#endif /* CONFIG_RESET_PHY_R */
+
+int fdt_fixup_board_phy(void *fdt)
+{
+ int mdio_offset;
+ int ret;
+ struct mii_dev *dev;
+
+ ret = 0;
+
+ dev = miiphy_get_dev_by_name(DEFAULT_WRIOP_MDIO2_NAME);
+ if (!get_inphi_phy_id(dev, INPHI_PHY_ADDR1, MDIO_MMD_VEND1)) {
+ mdio_offset = fdt_path_offset(fdt, "/soc/mdio@0x8B97000");
+
+ if (mdio_offset < 0)
+ mdio_offset = fdt_path_offset(fdt, "/mdio@0x8B97000");
+
+ if (mdio_offset < 0) {
+ printf("mdio@0x8B9700 node not found in dts\n");
+ return mdio_offset;
+ }
+
+ ret = fdt_setprop_string(fdt, mdio_offset, "status",
+ "disabled");
+ if (ret) {
+ printf("Could not set disable mdio@0x8B97000 %s\n",
+ fdt_strerror(ret));
+ return ret;
+ }
+ }
+
+ return ret;
+}
diff --git a/board/freescale/lx2160a/lx2160a.c b/board/freescale/lx2160a/lx2160a.c
new file mode 100644
index 0000000..a62222e
--- /dev/null
+++ b/board/freescale/lx2160a/lx2160a.c
@@ -0,0 +1,279 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2018 NXP
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <dm/platform_data/serial_pl01x.h>
+#include <i2c.h>
+#include <malloc.h>
+#include <errno.h>
+#include <netdev.h>
+#include <fsl_ddr.h>
+#include <fsl_sec.h>
+#include <asm/io.h>
+#include <fdt_support.h>
+#include <linux/libfdt.h>
+#include <fsl-mc/fsl_mc.h>
+#include <environment.h>
+#include <efi_loader.h>
+#include <asm/arch/mmu.h>
+#include <hwconfig.h>
+#include <asm/arch/fsl_serdes.h>
+#include <asm/arch/soc.h>
+#include "../common/qixis.h"
+#include "../common/vid.h"
+#include <fsl_immap.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static struct pl01x_serial_platdata serial0 = {
+#if CONFIG_CONS_INDEX == 0
+ .base = CONFIG_SYS_SERIAL0,
+#elif CONFIG_CONS_INDEX == 1
+ .base = CONFIG_SYS_SERIAL1,
+#else
+#error "Unsupported console index value."
+#endif
+ .type = TYPE_PL011,
+};
+
+U_BOOT_DEVICE(nxp_serial0) = {
+ .name = "serial_pl01x",
+ .platdata = &serial0,
+};
+
+static struct pl01x_serial_platdata serial1 = {
+ .base = CONFIG_SYS_SERIAL1,
+ .type = TYPE_PL011,
+};
+
+U_BOOT_DEVICE(nxp_serial1) = {
+ .name = "serial_pl01x",
+ .platdata = &serial1,
+};
+
+int select_i2c_ch_pca9547(u8 ch)
+{
+ int ret;
+
+ ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1);
+ if (ret) {
+ puts("PCA: failed to select proper channel\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static void uart_get_clock(void)
+{
+ serial0.clock = get_serial_clock();
+ serial1.clock = get_serial_clock();
+}
+
+int board_early_init_f(void)
+{
+#ifdef CONFIG_SYS_I2C_EARLY_INIT
+ i2c_early_init_f();
+#endif
+ /* get required clock for UART IP */
+ uart_get_clock();
+
+ fsl_lsch3_early_init_f();
+ return 0;
+}
+
+int esdhc_status_fixup(void *blob, const char *compat)
+{
+ /* Enable both esdhc DT nodes for LX2160ARDB */
+ do_fixup_by_compat(blob, compat, "status", "okay",
+ sizeof("okay"), 1);
+
+ return 0;
+}
+
+#if defined(CONFIG_VID)
+int i2c_multiplexer_select_vid_channel(u8 channel)
+{
+ return select_i2c_ch_pca9547(channel);
+}
+
+#endif
+
+int checkboard(void)
+{
+ enum boot_src src = get_boot_src();
+ char buf[64];
+ u8 sw;
+
+ cpu_name(buf);
+ printf("Board: %s-RDB, ", buf);
+
+ sw = QIXIS_READ(arch);
+ printf("Board version: %c, boot from ", (sw & 0xf) - 1 + 'A');
+
+ if (src == BOOT_SOURCE_SD_MMC) {
+ puts("SD\n");
+ } else {
+ sw = QIXIS_READ(brdcfg[0]);
+ sw = (sw >> QIXIS_XMAP_SHIFT) & QIXIS_XMAP_MASK;
+ switch (sw) {
+ case 0:
+ case 4:
+ puts("FlexSPI DEV#0\n");
+ break;
+ case 1:
+ puts("FlexSPI DEV#1\n");
+ break;
+ case 2:
+ case 3:
+ puts("FlexSPI EMU\n");
+ break;
+ default:
+ printf("invalid setting, xmap: %d\n", sw);
+ break;
+ }
+ }
+ printf("FPGA: v%d.%d\n", QIXIS_READ(scver), QIXIS_READ(tagdata));
+
+ puts("SERDES1 Reference: Clock1 = 161.13MHz Clock2 = 161.13MHz\n");
+ puts("SERDES2 Reference: Clock1 = 100MHz Clock2 = 100MHz\n");
+ puts("SERDES3 Reference: Clock1 = 100MHz Clock2 = 100Hz\n");
+ return 0;
+}
+
+unsigned long get_board_sys_clk(void)
+{
+ return 100000000;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+ return 100000000;
+}
+
+int board_init(void)
+{
+#ifdef CONFIG_ENV_IS_NOWHERE
+ gd->env_addr = (ulong)&default_environment[0];
+#endif
+
+ select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
+
+#ifdef CONFIG_FSL_CAAM
+ sec_init();
+#endif
+
+ return 0;
+}
+
+void detail_board_ddr_info(void)
+{
+ int i;
+ u64 ddr_size = 0;
+
+ puts("\nDDR ");
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
+ ddr_size += gd->bd->bi_dram[i].size;
+ print_size(ddr_size, "");
+ print_ddr_info(0);
+}
+
+#if defined(CONFIG_ARCH_MISC_INIT)
+int arch_misc_init(void)
+{
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_FSL_MC_ENET
+extern int fdt_fixup_board_phy(void *fdt);
+
+void fdt_fixup_board_enet(void *fdt)
+{
+ int offset;
+
+ offset = fdt_path_offset(fdt, "/soc/fsl-mc");
+
+ if (offset < 0)
+ offset = fdt_path_offset(fdt, "/fsl-mc");
+
+ if (offset < 0) {
+ printf("%s: fsl-mc node not found in device tree (error %d)\n",
+ __func__, offset);
+ return;
+ }
+
+ if ((get_mc_boot_status() == 0) && (get_dpl_apply_status() == 0)) {
+ fdt_status_okay(fdt, offset);
+ fdt_fixup_board_phy(fdt);
+ } else {
+ fdt_status_fail(fdt, offset);
+ }
+}
+
+void board_quiesce_devices(void)
+{
+ fsl_mc_ldpaa_exit(gd->bd);
+}
+#endif
+
+#ifdef CONFIG_OF_BOARD_SETUP
+
+int ft_board_setup(void *blob, bd_t *bd)
+{
+ int i;
+ u64 base[CONFIG_NR_DRAM_BANKS];
+ u64 size[CONFIG_NR_DRAM_BANKS];
+
+ ft_cpu_setup(blob, bd);
+
+ /* fixup DT for the three GPP DDR banks */
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+ base[i] = gd->bd->bi_dram[i].start;
+ size[i] = gd->bd->bi_dram[i].size;
+ }
+
+#ifdef CONFIG_RESV_RAM
+ /* reduce size if reserved memory is within this bank */
+ if (gd->arch.resv_ram >= base[0] &&
+ gd->arch.resv_ram < base[0] + size[0])
+ size[0] = gd->arch.resv_ram - base[0];
+ else if (gd->arch.resv_ram >= base[1] &&
+ gd->arch.resv_ram < base[1] + size[1])
+ size[1] = gd->arch.resv_ram - base[1];
+ else if (gd->arch.resv_ram >= base[2] &&
+ gd->arch.resv_ram < base[2] + size[2])
+ size[2] = gd->arch.resv_ram - base[2];
+#endif
+
+ fdt_fixup_memory_banks(blob, base, size, CONFIG_NR_DRAM_BANKS);
+
+#ifdef CONFIG_USB
+ fsl_fdt_fixup_dr_usb(blob, bd);
+#endif
+
+#ifdef CONFIG_FSL_MC_ENET
+ fdt_fsl_mc_fixup_iommu_map_entry(blob);
+ fdt_fixup_board_enet(blob);
+#endif
+
+ return 0;
+}
+#endif
+
+void qixis_dump_switch(void)
+{
+ int i, nr_of_cfgsw;
+
+ QIXIS_WRITE(cms[0], 0x00);
+ nr_of_cfgsw = QIXIS_READ(cms[1]);
+
+ puts("DIP switch settings dump:\n");
+ for (i = 1; i <= nr_of_cfgsw; i++) {
+ QIXIS_WRITE(cms[0], i);
+ printf("SW%d = (0x%02x)\n", i, QIXIS_READ(cms[1]));
+ }
+}