Add pixis_set_sgmii command
The 8544DS and 8572DS platforms support an optional SGMII riser card to
expose ethernet over an SGMII interface. Once the card is in, it is also
necessary to configure the board such that it uses the card, rather than
the on-board ethernet ports. This can either be done by flipping dip switches
on the motherboard, or by modifying registers in the pixis. Either way
requires a reboot.
This adds a command to allow users to choose which ports are routed through
the SGMII card, and which through the onboard ports. It also allows users
to revert to the current switch settings.
This code does not work on the 8572, as the PIXIS is different.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
diff --git a/board/freescale/common/pixis.c b/board/freescale/common/pixis.c
index 64e2e08..b5a0e84 100644
--- a/board/freescale/common/pixis.c
+++ b/board/freescale/common/pixis.c
@@ -26,6 +26,7 @@
#include <command.h>
#include <watchdog.h>
#include <asm/cache.h>
+#include <asm/io.h>
#include "pixis.h"
@@ -282,6 +283,60 @@
"diswd - Disable watchdog timer \n",
NULL);
+#ifdef CONFIG_FSL_SGMII_RISER
+int pixis_set_sgmii(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+ int which_tsec = -1;
+ uchar mask;
+ uchar switch_mask;
+
+ if (argc > 2)
+ if (strcmp(argv[1], "all") != 0)
+ which_tsec = simple_strtoul(argv[1], NULL, 0);
+
+ switch (which_tsec) {
+ case 1:
+ mask = PIXIS_VSPEED2_TSEC1SER;
+ switch_mask = PIXIS_VCFGEN1_TSEC1SER;
+ break;
+ case 3:
+ mask = PIXIS_VSPEED2_TSEC3SER;
+ switch_mask = PIXIS_VCFGEN1_TSEC3SER;
+ break;
+ default:
+ mask = PIXIS_VSPEED2_TSEC1SER | PIXIS_VSPEED2_TSEC3SER;
+ switch_mask = PIXIS_VCFGEN1_TSEC1SER | PIXIS_VCFGEN1_TSEC3SER;
+ break;
+ }
+
+ /* Toggle whether the switches or FPGA control the settings */
+ if (!strcmp(argv[argc - 1], "switch"))
+ clrbits_8((unsigned char *)PIXIS_BASE + PIXIS_VCFGEN1,
+ switch_mask);
+ else
+ setbits_8((unsigned char *)PIXIS_BASE + PIXIS_VCFGEN1,
+ switch_mask);
+
+ /* If it's not the switches, enable or disable SGMII, as specified */
+ if (!strcmp(argv[argc - 1], "on"))
+ clrbits_8((unsigned char *)PIXIS_BASE + PIXIS_VSPEED2, mask);
+ else if (!strcmp(argv[argc - 1], "off"))
+ setbits_8((unsigned char *)PIXIS_BASE + PIXIS_VSPEED2, mask);
+
+ return 0;
+}
+
+U_BOOT_CMD(
+ pixis_set_sgmii, CFG_MAXARGS, 1, pixis_set_sgmii,
+ "pixis_set_sgmii"
+ " - Enable or disable SGMII mode for a given TSEC \n",
+ "\npixis_set_sgmii [TSEC num] <on|off|switch>\n"
+ " TSEC num: 1,2,3,4 or 'all'. 'all' is default.\n"
+ " on - enables SGMII\n"
+ " off - disables SGMII\n"
+ " switch - use switch settings\n");
+#endif
+
/*
* This function takes the non-integral cpu:mpx pll ratio
* and converts it to an integer that can be used to assign