* Patch by Robin Getz, 13 Oct 2004:
Add standalone application to change SMC91C111 MAC addresses,
see examples/README.smc91111_eeprom
* Patch by Xiaogeng (Shawn) Jin, 12 Oct 2004:
Fix Flash support for ARM Integrator CP.
diff --git a/board/omap2420h4/config.mk b/board/omap2420h4/config.mk
index f2a533e..e6aa756 100644
--- a/board/omap2420h4/config.mk
+++ b/board/omap2420h4/config.mk
@@ -20,4 +20,3 @@
# This is either with a GP system or a signed boot image.
# easiest, and safest way to go if you can.
#TEXT_BASE = 0x40280000
-
diff --git a/board/omap2420h4/mem.c b/board/omap2420h4/mem.c
index 3ce38cc..9ae595b 100644
--- a/board/omap2420h4/mem.c
+++ b/board/omap2420h4/mem.c
@@ -74,9 +74,9 @@
if(running_in_sram()){
/* If running fully from SRAM this is OK. The Flash bus drops out for just a little.
- * but then comes back. If running from Flash this sequence kills you, thus you need
- * to run it using CONFIG_PARTIAL_SRAM.
- */
+ * but then comes back. If running from Flash this sequence kills you, thus you need
+ * to run it using CONFIG_PARTIAL_SRAM.
+ */
__raw_writel(MODE_BYPASS_FAST, CM_CLKEN_PLL); /* go to bypass, fast relock */
wait_on_value(BIT0|BIT1, BIT0, CM_IDLEST_CKGEN, LDELAY); /* wait till in bypass */
sdelay(1000);
@@ -172,14 +172,13 @@
cpu = get_cpu_type();
/* warning generated, though code generation is correct. this may bite later,
- * but is ok for now. there is only so much C code you can do on stack only
- * operation.
+ * but is ok for now. there is only so much C code you can do on stack only
+ * operation.
*/
if (cpu == CPU_2422){
sdata = (sdrc_data_t *)&sdrc_2422;
pass_type = STACKED;
- }
- else{
+ } else{
sdata = (sdrc_data_t *)&sdrc_2420;
pass_type = IP_DDR;
}
@@ -187,10 +186,10 @@
__asm__ __volatile__("": : :"memory"); /* limit compiler scope */
/* u-boot is compiled to run in DDR or SRAM at 8xxxxxxx or 4xxxxxxx.
- * If we are running in flash prior to relocation and we use data
- * here which is not pc relative we need to get the address correct.
- * We need to find the current flash mapping to dress up the initial
- * pointer load. As long as this is const data we should be ok.
+ * If we are running in flash prior to relocation and we use data
+ * here which is not pc relative we need to get the address correct.
+ * We need to find the current flash mapping to dress up the initial
+ * pointer load. As long as this is const data we should be ok.
*/
if((early) && running_in_flash()){
sdata = (sdrc_data_t *)(((u32)sdata & 0x0003FFFF) | get_gpmc0_base());
@@ -344,4 +343,3 @@
__raw_writel(H4_24XX_GPMC_CONFIG7_1, GPMC_CONFIG7_1); /* enable mapping */
sdelay(2000);
}
-
diff --git a/board/omap2420h4/omap2420h4.c b/board/omap2420h4/omap2420h4.c
index 697dfef..8c7982d 100644
--- a/board/omap2420h4/omap2420h4.c
+++ b/board/omap2420h4/omap2420h4.c
@@ -36,7 +36,6 @@
extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
#endif
-
static void wait_for_command_complete(unsigned int wd_base);
/*******************************************************
@@ -694,8 +693,6 @@
/* signal - Gpmc_ncs2; pin - E2; offset - 0x008C; mode - 0; Byte-2 Pull/up - N/A */
MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPMC_NCS0_BYTE2,
*MuxConfigReg = 0x00 ;
-
-
}
/****************************************************************
@@ -860,6 +857,3 @@
#endif
}
#endif
-
-
-
diff --git a/board/omap2420h4/platform.S b/board/omap2420h4/platform.S
index 86bf5ba..73ba462 100644
--- a/board/omap2420h4/platform.S
+++ b/board/omap2420h4/platform.S
@@ -183,4 +183,3 @@
.word PERIFERAL_PORT_BASE
SRAM_STACK:
.word LOW_LEVEL_SRAM_STACK
-
diff --git a/board/omap2420h4/sys_info.c b/board/omap2420h4/sys_info.c
index 78b936c..121d679 100644
--- a/board/omap2420h4/sys_info.c
+++ b/board/omap2420h4/sys_info.c
@@ -251,8 +251,6 @@
return(val);
}
-
-
/********************************************************
* running_in_flash() - tell if currently running in
* flash.
@@ -302,4 +300,3 @@
else
return(0);
}
-