mx6: Factor out common HDMI setup code
Instead of duplicating HDMI setup code for every mx6 board, factor out the common code
Signed-off-by: Pardeep Kumar Singla <b45784@freescale.com>
Acked-By: Eric Nelson <eric.nelson@boundarydevices.com>
diff --git a/arch/arm/cpu/armv7/mx6/clock.c b/arch/arm/cpu/armv7/mx6/clock.c
index 3c0d908..ce063ae 100644
--- a/arch/arm/cpu/armv7/mx6/clock.c
+++ b/arch/arm/cpu/armv7/mx6/clock.c
@@ -468,6 +468,14 @@
return 0;
}
+void enable_ipu_clock(void)
+{
+ struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+ int reg;
+ reg = readl(&mxc_ccm->CCGR3);
+ reg |= MXC_CCM_CCGR3_IPU1_IPU_DI0_OFFSET;
+ writel(reg, &mxc_ccm->CCGR3);
+}
/***************************************************/
U_BOOT_CMD(
diff --git a/arch/arm/cpu/armv7/mx6/soc.c b/arch/arm/cpu/armv7/mx6/soc.c
index fc436fb..a79369f 100644
--- a/arch/arm/cpu/armv7/mx6/soc.c
+++ b/arch/arm/cpu/armv7/mx6/soc.c
@@ -32,6 +32,8 @@
#include <asm/imx-common/boot_mode.h>
#include <asm/imx-common/dma.h>
#include <stdbool.h>
+#include <asm/arch/mxc_hdmi.h>
+#include <asm/arch/crm_regs.h>
struct scu_regs {
u32 ctrl;
@@ -228,3 +230,44 @@
void s_init(void)
{
}
+
+#ifdef CONFIG_IMX_HDMI
+void imx_enable_hdmi_phy(void)
+{
+ struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
+ u8 reg;
+ reg = readb(&hdmi->phy_conf0);
+ reg |= HDMI_PHY_CONF0_PDZ_MASK;
+ writeb(reg, &hdmi->phy_conf0);
+ udelay(3000);
+ reg |= HDMI_PHY_CONF0_ENTMDS_MASK;
+ writeb(reg, &hdmi->phy_conf0);
+ udelay(3000);
+ reg |= HDMI_PHY_CONF0_GEN2_TXPWRON_MASK;
+ writeb(reg, &hdmi->phy_conf0);
+ writeb(HDMI_MC_PHYRSTZ_ASSERT, &hdmi->mc_phyrstz);
+}
+
+void imx_setup_hdmi(void)
+{
+ struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+ struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
+ int reg;
+
+ /* Turn on HDMI PHY clock */
+ reg = readl(&mxc_ccm->CCGR2);
+ reg |= MXC_CCM_CCGR2_HDMI_TX_IAHBCLK_MASK|
+ MXC_CCM_CCGR2_HDMI_TX_ISFRCLK_MASK;
+ writel(reg, &mxc_ccm->CCGR2);
+ writeb(HDMI_MC_PHYRSTZ_DEASSERT, &hdmi->mc_phyrstz);
+ reg = readl(&mxc_ccm->chsccdr);
+ reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK|
+ MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK|
+ MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK);
+ reg |= (CHSCCDR_PODF_DIVIDE_BY_3
+ << MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET)
+ |(CHSCCDR_IPU_PRE_CLK_540M_PFD
+ << MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET);
+ writel(reg, &mxc_ccm->chsccdr);
+}
+#endif
diff --git a/arch/arm/include/asm/arch-mx6/clock.h b/arch/arm/include/asm/arch-mx6/clock.h
index cfd4edc..d03d24a 100644
--- a/arch/arm/include/asm/arch-mx6/clock.h
+++ b/arch/arm/include/asm/arch-mx6/clock.h
@@ -65,5 +65,5 @@
void enable_usboh3_clk(unsigned char enable);
int enable_sata_clock(void);
int enable_i2c_clk(unsigned char enable, unsigned i2c_num);
-
+void enable_ipu_clock(void);
#endif /* __ASM_ARCH_CLOCK_H */
diff --git a/arch/arm/include/asm/arch-mx6/mxc_hdmi.h b/arch/arm/include/asm/arch-mx6/mxc_hdmi.h
index 9dccb3f..5cd6aa6 100644
--- a/arch/arm/include/asm/arch-mx6/mxc_hdmi.h
+++ b/arch/arm/include/asm/arch-mx6/mxc_hdmi.h
@@ -21,6 +21,11 @@
#ifndef __MXC_HDMI_H__
#define __MXC_HDMI_H__
+#ifdef CONFIG_IMX_HDMI
+void imx_enable_hdmi_phy(void);
+void imx_setup_hdmi(void);
+#endif
+
/*
* Hdmi controller registers
*/
diff --git a/board/boundary/nitrogen6x/nitrogen6x.c b/board/boundary/nitrogen6x/nitrogen6x.c
index 8f0f9b8..1b82633 100644
--- a/board/boundary/nitrogen6x/nitrogen6x.c
+++ b/board/boundary/nitrogen6x/nitrogen6x.c
@@ -480,22 +480,9 @@
return readb(&hdmi->phy_stat0) & HDMI_PHY_HPD;
}
-static void enable_hdmi(struct display_info_t const *dev)
+static void do_enable_hdmi(struct display_info_t const *dev)
{
- struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
- u8 reg;
- printf("%s: setup HDMI monitor\n", __func__);
- reg = readb(&hdmi->phy_conf0);
- reg |= HDMI_PHY_CONF0_PDZ_MASK;
- writeb(reg, &hdmi->phy_conf0);
-
- udelay(3000);
- reg |= HDMI_PHY_CONF0_ENTMDS_MASK;
- writeb(reg, &hdmi->phy_conf0);
- udelay(3000);
- reg |= HDMI_PHY_CONF0_GEN2_TXPWRON_MASK;
- writeb(reg, &hdmi->phy_conf0);
- writeb(HDMI_MC_PHYRSTZ_ASSERT, &hdmi->mc_phyrstz);
+ imx_enable_hdmi_phy();
}
static int detect_i2c(struct display_info_t const *dev)
@@ -528,7 +515,7 @@
.addr = 0,
.pixfmt = IPU_PIX_FMT_RGB24,
.detect = detect_hdmi,
- .enable = enable_hdmi,
+ .enable = do_enable_hdmi,
.mode = {
.name = "HDMI",
.refresh = 60,
@@ -653,25 +640,15 @@
struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR;
struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
- struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
-
int reg;
+ enable_ipu_clock();
+ imx_setup_hdmi();
/* Turn on LDB0,IPU,IPU DI0 clocks */
reg = __raw_readl(&mxc_ccm->CCGR3);
- reg |= MXC_CCM_CCGR3_IPU1_IPU_DI0_OFFSET
- |MXC_CCM_CCGR3_LDB_DI0_MASK;
+ reg |= MXC_CCM_CCGR3_LDB_DI0_MASK;
writel(reg, &mxc_ccm->CCGR3);
- /* Turn on HDMI PHY clock */
- reg = __raw_readl(&mxc_ccm->CCGR2);
- reg |= MXC_CCM_CCGR2_HDMI_TX_IAHBCLK_MASK
- |MXC_CCM_CCGR2_HDMI_TX_ISFRCLK_MASK;
- writel(reg, &mxc_ccm->CCGR2);
-
- /* clear HDMI PHY reset */
- writeb(HDMI_MC_PHYRSTZ_DEASSERT, &hdmi->mc_phyrstz);
-
/* set PFD1_FRAC to 0x13 == 455 MHz (480*18)/0x13 */
writel(ANATOP_PFD_480_PFD1_FRAC_MASK, &anatop->pfd_480_clr);
writel(0x13<<ANATOP_PFD_480_PFD1_FRAC_SHIFT, &anatop->pfd_480_set);
@@ -689,15 +666,8 @@
writel(reg, &mxc_ccm->cscmr2);
reg = readl(&mxc_ccm->chsccdr);
- reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK
- |MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK
- |MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK);
reg |= (CHSCCDR_CLK_SEL_LDB_DI0
- <<MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET)
- |(CHSCCDR_PODF_DIVIDE_BY_3
- <<MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET)
- |(CHSCCDR_IPU_PRE_CLK_540M_PFD
- <<MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET);
+ <<MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
writel(reg, &mxc_ccm->chsccdr);
reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES
diff --git a/board/wandboard/wandboard.c b/board/wandboard/wandboard.c
index 43c02ac..6cd28ed 100644
--- a/board/wandboard/wandboard.c
+++ b/board/wandboard/wandboard.c
@@ -211,23 +211,6 @@
}
#if defined(CONFIG_VIDEO_IPUV3)
-static void enable_hdmi(void)
-{
- struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
- u8 reg;
- reg = readb(&hdmi->phy_conf0);
- reg |= HDMI_PHY_CONF0_PDZ_MASK;
- writeb(reg, &hdmi->phy_conf0);
-
- udelay(3000);
- reg |= HDMI_PHY_CONF0_ENTMDS_MASK;
- writeb(reg, &hdmi->phy_conf0);
- udelay(3000);
- reg |= HDMI_PHY_CONF0_GEN2_TXPWRON_MASK;
- writeb(reg, &hdmi->phy_conf0);
- writeb(HDMI_MC_PHYRSTZ_ASSERT, &hdmi->mc_phyrstz);
-}
-
static struct fb_videomode const hdmi = {
.name = "HDMI",
.refresh = 60,
@@ -253,7 +236,7 @@
if (ret)
printf("HDMI cannot be configured: %d\n", ret);
- enable_hdmi();
+ imx_enable_hdmi_phy();
return ret;
}
@@ -261,33 +244,14 @@
static void setup_display(void)
{
struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
- struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
int reg;
- /* Turn on IPU clock */
- reg = readl(&mxc_ccm->CCGR3);
- reg |= MXC_CCM_CCGR3_IPU1_IPU_DI0_OFFSET;
- writel(reg, &mxc_ccm->CCGR3);
-
- /* Turn on HDMI PHY clock */
- reg = readl(&mxc_ccm->CCGR2);
- reg |= MXC_CCM_CCGR2_HDMI_TX_IAHBCLK_MASK
- | MXC_CCM_CCGR2_HDMI_TX_ISFRCLK_MASK;
- writel(reg, &mxc_ccm->CCGR2);
-
- /* clear HDMI PHY reset */
- writeb(HDMI_MC_PHYRSTZ_DEASSERT, &hdmi->mc_phyrstz);
+ enable_ipu_clock();
+ imx_setup_hdmi();
reg = readl(&mxc_ccm->chsccdr);
- reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK
- | MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK
- | MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK);
reg |= (CHSCCDR_CLK_SEL_LDB_DI0
- << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET)
- | (CHSCCDR_PODF_DIVIDE_BY_3
- << MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET)
- | (CHSCCDR_IPU_PRE_CLK_540M_PFD
- << MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET);
+ << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
writel(reg, &mxc_ccm->chsccdr);
}
#endif /* CONFIG_VIDEO_IPUV3 */
diff --git a/include/configs/nitrogen6x.h b/include/configs/nitrogen6x.h
index 85eecfc..b057039 100644
--- a/include/configs/nitrogen6x.h
+++ b/include/configs/nitrogen6x.h
@@ -154,6 +154,7 @@
#define CONFIG_IPUV3_CLK 260000000
#define CONFIG_CMD_HDMIDETECT
#define CONFIG_CONSOLE_MUX
+#define CONFIG_IMX_HDMI
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
diff --git a/include/configs/wandboard.h b/include/configs/wandboard.h
index dd06bd7..1f83e89 100644
--- a/include/configs/wandboard.h
+++ b/include/configs/wandboard.h
@@ -100,6 +100,7 @@
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_LOGO
#define CONFIG_IPUV3_CLK 260000000
+#define CONFIG_IMX_HDMI
#if defined(CONFIG_MX6DL)
#define CONFIG_DEFAULT_FDT_FILE "imx6dl-wandboard.dtb"