MPC8308RDB: minimal support for devboard from Freescale
This patch provides support for MPC8308RDB development board from
Freescale with a minimal set of features:
Dual UART is supported
NOR flash is supported
Both TSEC Ethernet controllers are supported
PCI Express initialization is supported
The following features are enabled in configuration but not fully tested:
I2C (used to get the board revision)
I2C-connected RTC
VSC7385 switch
There is one (hopefully) minor issue: on soft reset the board sometimes
resets twice. I've not managed to find the fix for this problem yet.
As a workaround instruction cache can be disabled.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
diff --git a/board/freescale/mpc8308rdb/Makefile b/board/freescale/mpc8308rdb/Makefile
new file mode 100644
index 0000000..e9bfa2b
--- /dev/null
+++ b/board/freescale/mpc8308rdb/Makefile
@@ -0,0 +1,52 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+# (C) Copyright 2010
+# Ilya Yanok, Emcraft Systems, yanok@emcraft.com
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := $(BOARD).o sdram.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/freescale/mpc8308rdb/config.mk b/board/freescale/mpc8308rdb/config.mk
new file mode 100644
index 0000000..f768264
--- /dev/null
+++ b/board/freescale/mpc8308rdb/config.mk
@@ -0,0 +1 @@
+TEXT_BASE = 0xFE000000
diff --git a/board/freescale/mpc8308rdb/mpc8308rdb.c b/board/freescale/mpc8308rdb/mpc8308rdb.c
new file mode 100644
index 0000000..a864189
--- /dev/null
+++ b/board/freescale/mpc8308rdb/mpc8308rdb.c
@@ -0,0 +1,160 @@
+/*
+ * Copyright (C) 2010 Freescale Semiconductor, Inc.
+ * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <hwconfig.h>
+#include <i2c.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <pci.h>
+#include <mpc83xx.h>
+#include <vsc7385.h>
+#include <netdev.h>
+#include <asm/io.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_mpc83xx_serdes.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+ immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
+
+ if (in_be32(&im->pmc.pmccr1) & PMCCR1_POWER_OFF)
+ gd->flags |= GD_FLG_SILENT;
+
+ return 0;
+}
+
+static u8 read_board_info(void)
+{
+ u8 val8;
+ i2c_set_bus_num(0);
+
+ if (i2c_read(CONFIG_SYS_I2C_PCF8574A_ADDR, 0, 0, &val8, 1) == 0)
+ return val8;
+ else
+ return 0;
+}
+
+int checkboard(void)
+{
+ static const char * const rev_str[] = {
+ "1.0",
+ "<reserved>",
+ "<reserved>",
+ "<reserved>",
+ "<unknown>",
+ };
+ u8 info;
+ int i;
+
+ info = read_board_info();
+ i = (!info) ? 4 : info & 0x03;
+
+ printf("Board: Freescale MPC8308RDB Rev %s\n", rev_str[i]);
+
+ return 0;
+}
+
+static struct pci_region pcie_regions_0[] = {
+ {
+ .bus_start = CONFIG_SYS_PCIE1_MEM_BASE,
+ .phys_start = CONFIG_SYS_PCIE1_MEM_PHYS,
+ .size = CONFIG_SYS_PCIE1_MEM_SIZE,
+ .flags = PCI_REGION_MEM,
+ },
+ {
+ .bus_start = CONFIG_SYS_PCIE1_IO_BASE,
+ .phys_start = CONFIG_SYS_PCIE1_IO_PHYS,
+ .size = CONFIG_SYS_PCIE1_IO_SIZE,
+ .flags = PCI_REGION_IO,
+ },
+};
+
+void pci_init_board(void)
+{
+ immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
+ sysconf83xx_t *sysconf = &immr->sysconf;
+ clk83xx_t *clk = (clk83xx_t *)&immr->clk;
+ law83xx_t *pcie_law = sysconf->pcielaw;
+ struct pci_region *pcie_reg[] = { pcie_regions_0 };
+
+ fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_PEX,
+ FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
+
+ clrsetbits_be32(&clk->sccr, SCCR_PCIEXP1CM ,
+ SCCR_PCIEXP1CM_1);
+
+ /* Deassert the resets in the control register */
+ out_be32(&sysconf->pecr1, 0xE0008000);
+ udelay(2000);
+
+ /* Configure PCI Express Local Access Windows */
+ out_be32(&pcie_law[0].bar, CONFIG_SYS_PCIE1_BASE & LAWBAR_BAR);
+ out_be32(&pcie_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB);
+
+ mpc83xx_pcie_init(1, pcie_reg, 0);
+}
+/*
+ * Miscellaneous late-boot configurations
+ *
+ * If a VSC7385 microcode image is present, then upload it.
+*/
+int misc_init_r(void)
+{
+#ifdef CONFIG_VSC7385_IMAGE
+ if (vsc7385_upload_firmware((void *) CONFIG_VSC7385_IMAGE,
+ CONFIG_VSC7385_IMAGE_SIZE)) {
+ puts("Failure uploading VSC7385 microcode.\n");
+ return 1;
+ }
+#endif
+
+ return 0;
+}
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ ft_cpu_setup(blob, bd);
+ fdt_fixup_dr_usb(blob, bd);
+}
+#endif
+
+int board_eth_init(bd_t *bis)
+{
+ int rv, num_if = 0;
+
+ /* Initialize TSECs first */
+ if ((rv = cpu_eth_init(bis)) >= 0)
+ num_if += rv;
+ else
+ printf("ERROR: failed to initialize TSECs.\n");
+
+ if ((rv = pci_eth_init(bis)) >= 0)
+ num_if += rv;
+ else
+ printf("ERROR: failed to initialize PCI Ethernet.\n");
+
+ return num_if;
+}
diff --git a/board/freescale/mpc8308rdb/sdram.c b/board/freescale/mpc8308rdb/sdram.c
new file mode 100644
index 0000000..939c1b8
--- /dev/null
+++ b/board/freescale/mpc8308rdb/sdram.c
@@ -0,0 +1,126 @@
+/*
+ * Copyright (C) 2007 Freescale Semiconductor, Inc.
+ * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com
+ *
+ * Authors: Nick.Spence@freescale.com
+ * Wilson.Lo@freescale.com
+ * scottwood@freescale.com
+ *
+ * This files is mostly identical to the original from
+ * board\freescale\mpc8315erdb\sdram.c
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <mpc83xx.h>
+
+#include <asm/bitops.h>
+#include <asm/io.h>
+
+#include <asm/processor.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static void resume_from_sleep(void)
+{
+ u32 magic = *(u32 *)0;
+
+ typedef void (*func_t)(void);
+ func_t resume = *(func_t *)4;
+
+ if (magic == 0xf5153ae5)
+ resume();
+
+ gd->flags &= ~GD_FLG_SILENT;
+ puts("\nResume from sleep failed: bad magic word\n");
+}
+
+/* Fixed sdram init -- doesn't use serial presence detect.
+ *
+ * This is useful for faster booting in configs where the RAM is unlikely
+ * to be changed, or for things like NAND booting where space is tight.
+ */
+static long fixed_sdram(void)
+{
+ immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
+ u32 msize = CONFIG_SYS_DDR_SIZE * 1024 * 1024;
+ u32 msize_log2 = __ilog2(msize);
+
+ out_be32(&im->sysconf.ddrlaw[0].bar,
+ CONFIG_SYS_DDR_SDRAM_BASE & 0xfffff000);
+ out_be32(&im->sysconf.ddrlaw[0].ar, LBLAWAR_EN | (msize_log2 - 1));
+ out_be32(&im->sysconf.ddrcdr, CONFIG_SYS_DDRCDR_VALUE);
+
+ /*
+ * Erratum DDR3 requires a 50ms delay after clearing DDRCDR[DDR_cfg],
+ * or the DDR2 controller may fail to initialize correctly.
+ */
+ udelay(50000);
+
+ out_be32(&im->ddr.csbnds[0].csbnds, (msize - 1) >> 24);
+ out_be32(&im->ddr.cs_config[0], CONFIG_SYS_DDR_CS0_CONFIG);
+
+ /* Currently we use only one CS, so disable the other bank. */
+ out_be32(&im->ddr.cs_config[1], 0);
+
+ out_be32(&im->ddr.sdram_clk_cntl, CONFIG_SYS_DDR_SDRAM_CLK_CNTL);
+ out_be32(&im->ddr.timing_cfg_3, CONFIG_SYS_DDR_TIMING_3);
+ out_be32(&im->ddr.timing_cfg_1, CONFIG_SYS_DDR_TIMING_1);
+ out_be32(&im->ddr.timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
+ out_be32(&im->ddr.timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
+
+ if (in_be32(&im->pmc.pmccr1) & PMCCR1_POWER_OFF) {
+ out_be32(&im->ddr.sdram_cfg,
+ CONFIG_SYS_DDR_SDRAM_CFG | SDRAM_CFG_BI);
+ } else {
+ out_be32(&im->ddr.sdram_cfg, CONFIG_SYS_DDR_SDRAM_CFG);
+ }
+
+ out_be32(&im->ddr.sdram_cfg2, CONFIG_SYS_DDR_SDRAM_CFG2);
+ out_be32(&im->ddr.sdram_mode, CONFIG_SYS_DDR_MODE);
+ out_be32(&im->ddr.sdram_mode2, CONFIG_SYS_DDR_MODE2);
+
+ out_be32(&im->ddr.sdram_interval, CONFIG_SYS_DDR_INTERVAL);
+ sync();
+
+ /* enable DDR controller */
+ setbits_be32(&im->ddr.sdram_cfg, SDRAM_CFG_MEM_EN);
+ sync();
+
+ return get_ram_size(CONFIG_SYS_DDR_SDRAM_BASE, msize);
+}
+
+phys_size_t initdram(int board_type)
+{
+ immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
+ u32 msize;
+
+ if ((in_be32(&im->sysconf.immrbar) & IMMRBAR_BASE_ADDR) != (u32)im)
+ return -1;
+
+ /* DDR SDRAM */
+ msize = fixed_sdram();
+
+ if (in_be32(&im->pmc.pmccr1) & PMCCR1_POWER_OFF)
+ resume_from_sleep();
+
+ /* return total bus SDRAM size(bytes) -- DDR */
+ return msize;
+}