board: Add Qualcomm Dragonboard 410C support
This commit add support for 96Boards Dragonboard410C.
It is board based on APQ8016 Qualcomm SoC, complying with
96boards specification.
Features (present out of the box):
- 4x Cortex A53 (ARMv8)
- 2x USB Host port
- 1x USB Device port
- 4x LEDs
- 1x HDMI connector
- 1x uSD connector
- 3x buttons (Power, Vol+, Vol-/Reset)
- WIFI, Bluetooth with integrated antenna
- 8GiB eMMC
U-Boot boots chained with fastboot in 64-bit mode.
For detailed build instructions see readme.txt in board directory.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Tested-by: Simon Glass <sjg@chromium.org>
diff --git a/board/qualcomm/dragonboard410c/dragonboard410c.c b/board/qualcomm/dragonboard410c/dragonboard410c.c
new file mode 100644
index 0000000..1fa5664
--- /dev/null
+++ b/board/qualcomm/dragonboard410c/dragonboard410c.c
@@ -0,0 +1,131 @@
+/*
+ * Board init file for Dragonboard 410C
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <usb.h>
+#include <asm/gpio.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int dram_init(void)
+{
+ gd->ram_size = PHYS_SDRAM_1_SIZE;
+ return 0;
+}
+
+void dram_init_banksize(void)
+{
+ gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+ gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+}
+
+
+int board_prepare_usb(enum usb_init_type type)
+{
+ static struct udevice *pmic_gpio;
+ static struct gpio_desc hub_reset, usb_sel;
+ int ret = 0, node;
+
+ if (!pmic_gpio) {
+ ret = uclass_get_device_by_name(UCLASS_GPIO,
+ "pm8916_gpios@c000",
+ &pmic_gpio);
+ if (ret < 0) {
+ printf("Failed to find pm8916_gpios@c000 node.\n");
+ return ret;
+ }
+ }
+
+ /* Try to request gpios needed to start usb host on dragonboard */
+ if (!dm_gpio_is_valid(&hub_reset)) {
+ node = fdt_subnode_offset(gd->fdt_blob, pmic_gpio->of_offset,
+ "usb_hub_reset_pm");
+ if (node < 0) {
+ printf("Failed to find usb_hub_reset_pm dt node.\n");
+ return node;
+ }
+ ret = gpio_request_by_name_nodev(gd->fdt_blob, node, "gpios", 0,
+ &hub_reset, 0);
+ if (ret < 0) {
+ printf("Failed to request usb_hub_reset_pm gpio.\n");
+ return ret;
+ }
+ }
+
+ if (!dm_gpio_is_valid(&usb_sel)) {
+ node = fdt_subnode_offset(gd->fdt_blob, pmic_gpio->of_offset,
+ "usb_sw_sel_pm");
+ if (node < 0) {
+ printf("Failed to find usb_sw_sel_pm dt node.\n");
+ return 0;
+ }
+ ret = gpio_request_by_name_nodev(gd->fdt_blob, node, "gpios", 0,
+ &usb_sel, 0);
+ if (ret < 0) {
+ printf("Failed to request usb_sw_sel_pm gpio.\n");
+ return ret;
+ }
+ }
+
+ if (type == USB_INIT_HOST) {
+ /* Start USB Hub */
+ dm_gpio_set_dir_flags(&hub_reset,
+ GPIOD_IS_OUT | GPIOD_IS_OUT_ACTIVE);
+ mdelay(100);
+ /* Switch usb to host connectors */
+ dm_gpio_set_dir_flags(&usb_sel,
+ GPIOD_IS_OUT | GPIOD_IS_OUT_ACTIVE);
+ mdelay(100);
+ } else { /* Device */
+ /* Disable hub */
+ dm_gpio_set_dir_flags(&hub_reset, GPIOD_IS_OUT);
+ /* Switch back to device connector */
+ dm_gpio_set_dir_flags(&usb_sel, GPIOD_IS_OUT);
+ }
+
+ return 0;
+}
+
+int board_init(void)
+{
+ return 0;
+}
+
+/* Check for vol- button - if pressed - stop autoboot */
+int misc_init_r(void)
+{
+ struct udevice *pon;
+ struct gpio_desc resin;
+ int node, ret;
+
+ ret = uclass_get_device_by_name(UCLASS_GPIO, "pm8916_pon@800", &pon);
+ if (ret < 0) {
+ printf("Failed to find PMIC pon node. Check device tree\n");
+ return 0;
+ }
+
+ node = fdt_subnode_offset(gd->fdt_blob, pon->of_offset, "key_vol_down");
+ if (node < 0) {
+ printf("Failed to find key_vol_down node. Check device tree\n");
+ return 0;
+ }
+
+ if (gpio_request_by_name_nodev(gd->fdt_blob, node, "gpios", 0, &resin,
+ 0)) {
+ printf("Failed to request key_vol_down button.\n");
+ return 0;
+ }
+
+ if (dm_gpio_get_value(&resin)) {
+ setenv("bootdelay", "-1");
+ printf("Power button pressed - dropping to console.\n");
+ }
+
+ return 0;
+}