net: phy: dp83867: add workaround for incorrect RX_CTRL pin strap

The data manual for DP83867IR/CR, SNLS484E[1], revised march 2017,
advises that strapping RX_DV/RX_CTRL pin in mode 1 and 2 is not
supported (see note below Table 5 (4-Level Strap Pins)).

It further advises that if a board has this pin strapped in mode 1 and
mode 2, then bit[7] of Configuration Register 4 (address 0x0031) must
be cleared to 0. This is to ensure proper operation of PHY.

Since it is not possible to detect in software if RX_DV/RX_CTRL pin is
incorrectly strapped, add a device-tree property to advertise this and
allow corrective action in software.
[1] http://www.ti.com/lit/ds/snls484e/snls484e.pdf

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
diff --git a/drivers/net/phy/ti.c b/drivers/net/phy/ti.c
index 8f3ed8a..f1c9f7b 100644
--- a/drivers/net/phy/ti.c
+++ b/drivers/net/phy/ti.c
@@ -24,6 +24,7 @@
 #define DP83867_CTRL		0x1f
 
 /* Extended Registers */
+#define DP83867_CFG4		0x0031
 #define DP83867_RGMIICTL	0x0032
 #define DP83867_RGMIIDCTL	0x0086
 #define DP83867_IO_MUX_CFG	0x0170
@@ -95,6 +96,7 @@
 	int tx_id_delay;
 	int fifo_depth;
 	int io_impedance;
+	bool rxctrl_strap_quirk;
 };
 
 /**
@@ -183,6 +185,8 @@
 	else
 		dp83867->io_impedance = -EINVAL;
 
+	if (fdtdec_get_bool(fdt, node, "ti,dp83867-rxctrl-strap-quirk"))
+		dp83867->rxctrl_strap_quirk = true;
 	dp83867->rx_id_delay = fdtdec_get_uint(gd->fdt_blob, dev_of_offset(dev),
 				 "ti,rx-internal-delay", -1);
 
@@ -232,6 +236,15 @@
 	phy_write(phydev, MDIO_DEVAD_NONE, DP83867_CTRL,
 		  val | DP83867_SW_RESTART);
 
+	/* Mode 1 or 2 workaround */
+	if (dp83867->rxctrl_strap_quirk) {
+		val = phy_read_mmd_indirect(phydev, DP83867_CFG4,
+					    DP83867_DEVADDR, phydev->addr);
+		val &= ~BIT(7);
+		phy_write_mmd_indirect(phydev, DP83867_CFG4,
+				       DP83867_DEVADDR, phydev->addr, val);
+	}
+
 	if (phy_interface_is_rgmii(phydev)) {
 		ret = phy_write(phydev, MDIO_DEVAD_NONE, MII_DP83867_PHYCTRL,
 			(DP83867_MDI_CROSSOVER_AUTO << DP83867_MDI_CROSSOVER) |