x86: Kconfig: Divide the target selection to vendor/model
Let arch/x86/Kconfig prompt board vendor first, then select
the board model under that vendor. This way arch/x86/Kconfig
only needs concern board vendor and leave the supported target
list to board/<vendor>/Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index aaceaef..c3cc144 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -11,79 +11,25 @@
default y
choice
- prompt "Target select"
+ prompt "Mainboard vendor"
+ default VENDOR_COREBOOT
-config TARGET_COREBOOT
- bool "Support coreboot"
- help
- This target is used for running U-Boot on top of Coreboot. In
- this case Coreboot does the early inititalisation, and U-Boot
- takes over once the RAM, video and CPU are fully running.
- U-Boot is loaded as a fallback payload from Coreboot, in
- Coreboot terminology. This method was used for the Chromebook
- Pixel when launched.
+config VENDOR_COREBOOT
+ bool "coreboot"
-config TARGET_CHROMEBOOK_LINK
- bool "Support Chromebook link"
- help
- This is the Chromebook Pixel released in 2013. It uses an Intel
- i5 Ivybridge which is a die-shrink of Sandybridge, with 4GB of
- SDRAM. It has a Panther Point platform controller hub, PCIe
- WiFi and Bluetooth. It also includes a 720p webcam, USB SD
- reader, microphone and speakers, display port and 32GB SATA
- solid state drive. There is a Chrome OS EC connected on LPC,
- and it provides a 2560x1700 high resolution touch-enabled LCD
- display.
+config VENDOR_GOOGLE
+ bool "Google"
-config TARGET_CHROMEBOX_PANTHER
- bool "Support Chromebox panther (not available)"
- select n
- help
- Note: At present this must be used with Coreboot. See README.x86
- for instructions.
-
- This is the Asus Chromebox CN60 released in 2014. It uses an Intel
- Haswell Celeron 2955U Dual Core CPU with 2GB of SDRAM. It has a
- Lynx Point platform controller hub, PCIe WiFi and Bluetooth. It also
- includes a USB SD reader, four USB3 ports, display port and HDMI
- video output and a 16GB SATA solid state drive. There is no Chrome
- OS EC on this model.
-
-config TARGET_CROWNBAY
- bool "Support Intel Crown Bay CRB"
- help
- This is the Intel Crown Bay Customer Reference Board. It contains
- the Intel Atom Processor E6xx populated on the COM Express module
- with 1GB DDR2 soldered down memory and a carrier board with the
- Intel Platform Controller Hub EG20T, other system components and
- peripheral connectors for PCIe/SATA/USB/LAN/SD/UART/Audio/LVDS.
-
-config TARGET_MINNOWMAX
- bool "Support Intel Minnowboard MAX"
- help
- This is the Intel Minnowboard MAX. It contains an Atom E3800
- processor in a small form factor with Ethernet, micro-SD, USB 2,
- USB 3, SATA, serial console, some GPIOs and HDMI 1.3 video out.
- It requires some binary blobs - see README.x86 for details.
-
- Note that PCIE_ECAM_BASE is set up by the FSP so the value used
- by U-Boot matches that value.
-
-config TARGET_GALILEO
- bool "Support Intel Galileo"
- help
- This is the Intel Galileo board, which is the first in a family of
- Arduino-certified development and prototyping boards based on Intel
- architecture. It includes an Intel Quark SoC X1000 processor, a 32-bit
- single-core, single-thread, Intel Pentium processor instrunction set
- architecture (ISA) compatible, operating at speeds up to 400Mhz,
- along with 256MB DDR3 memory. It supports a wide range of industry
- standard I/O interfaces, including a full-sized mini-PCIe slot,
- one 100Mb Ethernet port, a microSD card slot, a USB host port and
- a USB client port.
+config VENDOR_INTEL
+ bool "Intel"
endchoice
+# board-specific options below
+source "board/coreboot/Kconfig"
+source "board/google/Kconfig"
+source "board/intel/Kconfig"
+
config DM_SPI
default y
@@ -473,18 +419,6 @@
should be enough for most boards. If this does not fit your board,
change it according to your needs.
-source "board/coreboot/coreboot/Kconfig"
-
-source "board/google/chromebook_link/Kconfig"
-
-source "board/google/chromebox_panther/Kconfig"
-
-source "board/intel/crownbay/Kconfig"
-
-source "board/intel/minnowmax/Kconfig"
-
-source "board/intel/galileo/Kconfig"
-
config PCIE_ECAM_BASE
hex
default 0xe0000000