arm: mvebu: Add support for generating NAND kwbimage
Add a new Kconfig option CONFIG_MVEBU_SPL_BOOT_DEVICE_NAND which instruct
make to generate kwbimage with NAND header. This image is used for booting
from NAND flash (either SPI or parallel).
Support is very simple, SPL after finishes DDR training returns back to the
BootROM (via CONFIG_SPL_BOOTROM_SUPPORT option) and BootROM then loads and
executes U-Boot proper.
To generate correct kwbimage NAND header, it is required to set following
Kconfig options:
CONFIG_SYS_NAND_PAGE_SIZE
CONFIG_SYS_NAND_BLOCK_SIZE
CONFIG_MVEBU_SPL_NAND_BADBLK_LOCATION
They are used only by make / mkimage when generating final kwbimage.
CONFIG_MVEBU_SPL_NAND_BADBLK_LOCATION is a new mvebu specific Kconfig
option which is set into kwbimage NAND_BADBLK_LOCATION header field.
Signed-off-by: Pali Rohár <pali@kernel.org>
diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
index a574062..cf24958 100644
--- a/arch/arm/mach-mvebu/Kconfig
+++ b/arch/arm/mach-mvebu/Kconfig
@@ -339,6 +339,11 @@
imply SPL_SPI
select SPL_BOOTROM_SUPPORT
+config MVEBU_SPL_BOOT_DEVICE_NAND
+ bool "NAND flash (SPI or parallel)"
+ select MTD_RAW_NAND
+ select SPL_BOOTROM_SUPPORT
+
config MVEBU_SPL_BOOT_DEVICE_MMC
bool "SDIO/MMC card"
imply ENV_IS_IN_MMC
@@ -364,6 +369,14 @@
endchoice
+config MVEBU_SPL_NAND_BADBLK_LOCATION
+ hex "NAND Bad block indicator location"
+ depends on MVEBU_SPL_BOOT_DEVICE_NAND
+ range 0x0 0x1
+ help
+ Value 0x0 = SLC flash = BBI at page 0 or page 1
+ Value 0x1 = MLC flash = BBI at last page in the block
+
config MVEBU_EFUSE
bool "Enable eFuse support"
depends on HAVE_MVEBU_EFUSE
diff --git a/arch/arm/mach-mvebu/Makefile b/arch/arm/mach-mvebu/Makefile
index a9f506c..c5c7ab7 100644
--- a/arch/arm/mach-mvebu/Makefile
+++ b/arch/arm/mach-mvebu/Makefile
@@ -50,6 +50,9 @@
ifneq ($(CONFIG_MVEBU_SPL_BOOT_DEVICE_SPI),)
KWB_CFG_BOOT_FROM=spi
endif
+ifneq ($(CONFIG_MVEBU_SPL_BOOT_DEVICE_NAND),)
+ KWB_CFG_BOOT_FROM=nand
+endif
ifneq ($(CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC),)
KWB_CFG_BOOT_FROM=sdio
endif
@@ -60,6 +63,13 @@
KWB_CFG_BOOT_FROM=uart
endif
+ifneq ($(CONFIG_MVEBU_SPL_BOOT_DEVICE_NAND),)
+KWB_REPLACE += NAND_PAGE_SIZE NAND_BLKSZ NAND_BADBLK_LOCATION
+KWB_CFG_NAND_PAGE_SIZE = $(CONFIG_SYS_NAND_PAGE_SIZE)
+KWB_CFG_NAND_BLKSZ = $(CONFIG_SYS_NAND_BLOCK_SIZE)
+KWB_CFG_NAND_BADBLK_LOCATION = $(CONFIG_MVEBU_SPL_NAND_BADBLK_LOCATION)
+endif
+
ifneq ($(CONFIG_SECURED_MODE_IMAGE),)
KWB_REPLACE += CSK_INDEX
KWB_CFG_CSK_INDEX = $(CONFIG_SECURED_MODE_CSK_INDEX)
diff --git a/arch/arm/mach-mvebu/kwbimage.cfg.in b/arch/arm/mach-mvebu/kwbimage.cfg.in
index ccb0997..90cf00c 100644
--- a/arch/arm/mach-mvebu/kwbimage.cfg.in
+++ b/arch/arm/mach-mvebu/kwbimage.cfg.in
@@ -11,6 +11,11 @@
# Boot Media configurations
#@BOOT_FROM
+# NAND configuration
+#@NAND_PAGE_SIZE
+#@NAND_BLKSZ
+#@NAND_BADBLK_LOCATION
+
# Enable BootROM output via DEBUG flag on SoCs which require it
#@DEBUG
diff --git a/drivers/mtd/nand/raw/Kconfig b/drivers/mtd/nand/raw/Kconfig
index 5b35da4..5c7b0d9 100644
--- a/drivers/mtd/nand/raw/Kconfig
+++ b/drivers/mtd/nand/raw/Kconfig
@@ -628,7 +628,8 @@
config SYS_NAND_BLOCK_SIZE
hex "NAND chip eraseblock size"
- depends on ARCH_SUNXI || SPL_NAND_SUPPORT || TPL_NAND_SUPPORT
+ depends on ARCH_SUNXI || SPL_NAND_SUPPORT || TPL_NAND_SUPPORT || \
+ MVEBU_SPL_BOOT_DEVICE_NAND
depends on !NAND_MXS && !NAND_DENALI_DT && !NAND_LPC32XX_MLC && \
!NAND_FSL_IFC && !NAND_MT7621
help
@@ -655,6 +656,7 @@
hex "NAND chip page size"
depends on ARCH_SUNXI || NAND_OMAP_GPMC || NAND_LPC32XX_SLC || \
SPL_NAND_SIMPLE || (NAND_MXC && SPL_NAND_SUPPORT) || \
+ MVEBU_SPL_BOOT_DEVICE_NAND || \
(NAND_ATMEL && SPL_NAND_SUPPORT) || SPL_GENERATE_ATMEL_PMECC_HEADER
depends on !NAND_MXS && !NAND_DENALI_DT && !NAND_LPC32XX_MLC && !NAND_MT7621
help