rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
diff --git a/board/LEOX/elpt860/elpt860.c b/board/LEOX/elpt860/elpt860.c
index 5f50631..905df92 100644
--- a/board/LEOX/elpt860/elpt860.c
+++ b/board/LEOX/elpt860/elpt860.c
@@ -138,23 +138,23 @@
/* ------------------------------------------------------------------------- */
-#define CFG_PC4 0x0800
+#define CONFIG_SYS_PC4 0x0800
-#define CFG_DS1 CFG_PC4
+#define CONFIG_SYS_DS1 CONFIG_SYS_PC4
/*
* Very early board init code (fpga boot, etc.)
*/
int board_early_init_f (void)
{
- volatile immap_t *immr = (immap_t *) CFG_IMMR;
+ volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
/*
* Light up the red led on ELPT860 pcb (DS1) (PCDAT)
*/
- immr->im_ioport.iop_pcdat &= ~CFG_DS1; /* PCDAT (DS1 = 0) */
- immr->im_ioport.iop_pcpar &= ~CFG_DS1; /* PCPAR (0=general purpose I/O) */
- immr->im_ioport.iop_pcdir |= CFG_DS1; /* PCDIR (I/O: 0=input, 1=output) */
+ immr->im_ioport.iop_pcdat &= ~CONFIG_SYS_DS1; /* PCDAT (DS1 = 0) */
+ immr->im_ioport.iop_pcpar &= ~CONFIG_SYS_DS1; /* PCPAR (0=general purpose I/O) */
+ immr->im_ioport.iop_pcdir |= CONFIG_SYS_DS1; /* PCDIR (I/O: 0=input, 1=output) */
return (0); /* success */
}
@@ -181,7 +181,7 @@
phys_size_t initdram (int board_type)
{
- volatile immap_t *immap = (immap_t *) CFG_IMMR;
+ volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
long int size8, size9;
long int size_b0 = 0;
@@ -207,7 +207,7 @@
* with two SDRAM banks or four cycles every 31.2 us with one
* bank. It will be adjusted after memory sizing.
*/
- memctl->memc_mptpr = CFG_MPTPR_2BK_8K;
+ memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_8K;
/*
* The following value is used as an address (i.e. opcode) for
@@ -229,10 +229,10 @@
* preliminary addresses - these have to be modified after the
* SDRAM size has been determined.
*/
- memctl->memc_or1 = CFG_OR1_PRELIM;
- memctl->memc_br1 = CFG_BR1_PRELIM;
+ memctl->memc_or1 = CONFIG_SYS_OR1_PRELIM;
+ memctl->memc_br1 = CONFIG_SYS_BR1_PRELIM;
- memctl->memc_mamr = CFG_MAMR_8COL & (~(MAMR_PTAE)); /* no refresh yet */
+ memctl->memc_mamr = CONFIG_SYS_MAMR_8COL & (~(MAMR_PTAE)); /* no refresh yet */
udelay (200);
@@ -252,7 +252,7 @@
*
* try 8 column mode
*/
- size8 = dram_size (CFG_MAMR_8COL,
+ size8 = dram_size (CONFIG_SYS_MAMR_8COL,
SDRAM_BASE1_PRELIM, SDRAM_MAX_SIZE);
udelay (1000);
@@ -260,7 +260,7 @@
/*
* try 9 column mode
*/
- size9 = dram_size (CFG_MAMR_9COL,
+ size9 = dram_size (CONFIG_SYS_MAMR_9COL,
SDRAM_BASE1_PRELIM, SDRAM_MAX_SIZE);
if (size8 < size9) { /* leave configuration at 9 columns */
@@ -269,7 +269,7 @@
} else { /* back to 8 columns */
size_b0 = size8;
- memctl->memc_mamr = CFG_MAMR_8COL;
+ memctl->memc_mamr = CONFIG_SYS_MAMR_8COL;
udelay (500);
/* debug ("SDRAM Bank 0 in 8 column mode: %ld MB\n", size >> 20); */
}
@@ -282,22 +282,22 @@
*/
if (size_b0 < 0x02000000) {
/* reduce to 15.6 us (62.4 us / quad) */
- memctl->memc_mptpr = CFG_MPTPR_2BK_4K;
+ memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_4K;
udelay (1000);
}
/*
* Final mapping: map bigger bank first
*/
- memctl->memc_or1 = ((-size_b0) & 0xFFFF0000) | CFG_OR_TIMING_SDRAM;
- memctl->memc_br1 = (CFG_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V;
+ memctl->memc_or1 = ((-size_b0) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM;
+ memctl->memc_br1 = (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V;
{
unsigned long reg;
/* adjust refresh rate depending on SDRAM type, one bank */
reg = memctl->memc_mptpr;
- reg >>= 1; /* reduce to CFG_MPTPR_1BK_8K / _4K */
+ reg >>= 1; /* reduce to CONFIG_SYS_MPTPR_1BK_8K / _4K */
memctl->memc_mptpr = reg;
}
@@ -319,7 +319,7 @@
static long int
dram_size (long int mamr_value, long int *base, long int maxsize)
{
- volatile immap_t *immap = (immap_t *) CFG_IMMR;
+ volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
memctl->memc_mamr = mamr_value;
@@ -329,20 +329,20 @@
/* ------------------------------------------------------------------------- */
-#define CFG_PA1 0x4000
-#define CFG_PA2 0x2000
+#define CONFIG_SYS_PA1 0x4000
+#define CONFIG_SYS_PA2 0x2000
-#define CFG_LBKs (CFG_PA2 | CFG_PA1)
+#define CONFIG_SYS_LBKs (CONFIG_SYS_PA2 | CONFIG_SYS_PA1)
void reset_phy (void)
{
- volatile immap_t *immr = (immap_t *) CFG_IMMR;
+ volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
/*
* Ensure LBK LXT901 ethernet 1 & 2 = 0 ... for normal loopback in effect
* and no AUI loopback
*/
- immr->im_ioport.iop_padat &= ~CFG_LBKs; /* PADAT (LBK eth 1&2 = 0) */
- immr->im_ioport.iop_papar &= ~CFG_LBKs; /* PAPAR (0=general purpose I/O) */
- immr->im_ioport.iop_padir |= CFG_LBKs; /* PADIR (I/O: 0=input, 1=output) */
+ immr->im_ioport.iop_padat &= ~CONFIG_SYS_LBKs; /* PADAT (LBK eth 1&2 = 0) */
+ immr->im_ioport.iop_papar &= ~CONFIG_SYS_LBKs; /* PAPAR (0=general purpose I/O) */
+ immr->im_ioport.iop_padir |= CONFIG_SYS_LBKs; /* PADIR (I/O: 0=input, 1=output) */
}