rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
diff --git a/board/cm5200/cm5200.c b/board/cm5200/cm5200.c
index 24e8db0..9e2f1a5 100644
--- a/board/cm5200/cm5200.c
+++ b/board/cm5200/cm5200.c
@@ -57,7 +57,7 @@
static hw_id_t hw_id;
-#ifndef CFG_RAMBOOT
+#ifndef CONFIG_SYS_RAMBOOT
/*
* Helper function to initialize SDRAM controller.
*/
@@ -87,7 +87,7 @@
/* normal operation */
*(vu_long *)MPC5XXX_SDRAM_CTRL = mem_conf->control | hi_addr_bit;
}
-#endif /* CFG_RAMBOOT */
+#endif /* CONFIG_SYS_RAMBOOT */
/*
@@ -117,7 +117,7 @@
phys_size_t initdram(int board_type)
{
ulong dramsize = 0;
-#ifndef CFG_RAMBOOT
+#ifndef CONFIG_SYS_RAMBOOT
ulong test1, test2;
mem_conf_t *mem_conf;
@@ -131,9 +131,9 @@
*(vu_long *)MPC5XXX_SDRAM_CONFIG2 = mem_conf->config2;
sdram_start(0, mem_conf);
- test1 = get_ram_size((long *)CFG_SDRAM_BASE, 0x80000000);
+ test1 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
sdram_start(1, mem_conf);
- test2 = get_ram_size((long *)CFG_SDRAM_BASE, 0x80000000);
+ test2 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
if (test1 > test2) {
sdram_start(0, mem_conf);
dramsize = test1;
@@ -150,14 +150,14 @@
__builtin_ffs(dramsize >> 20) - 1;
} else
*(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */
-#else /* CFG_RAMBOOT */
+#else /* CONFIG_SYS_RAMBOOT */
/* retrieve size of memory connected to SDRAM CS0 */
dramsize = *(vu_long *)MPC5XXX_SDRAM_CS0CFG & 0xFF;
if (dramsize >= 0x13)
dramsize = (1 << (dramsize - 0x13)) << 20;
else
dramsize = 0;
-#endif /* !CFG_RAMBOOT */
+#endif /* !CONFIG_SYS_RAMBOOT */
/*
* On MPC5200B we need to set the special configuration delay in the
@@ -178,7 +178,7 @@
{
int i;
for (i = 0; i < HW_ID_ELEM_COUNT; ++i)
- if (i2c_read(CFG_I2C_EEPROM,
+ if (i2c_read(CONFIG_SYS_I2C_EEPROM,
hw_id_format[i].offset,
2,
(uchar *)&hw_id[i][0],
@@ -298,7 +298,7 @@
* also use a little trick to silence I2C-related output.
*/
gd->flags |= GD_FLG_SILENT;
- i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE);
+ i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
gd->flags &= ~GD_FLG_SILENT;
read_hw_id(hw_id_tmp);
@@ -363,7 +363,7 @@
char hostname[MODULE_NAME_MAXLEN];
/* Read ethaddr from EEPROM */
- if (i2c_read(CFG_I2C_EEPROM, CONFIG_MAC_OFFSET, 2, buf, 6) == 0) {
+ if (i2c_read(CONFIG_SYS_I2C_EEPROM, CONFIG_MAC_OFFSET, 2, buf, 6) == 0) {
sprintf(str, "%02X:%02X:%02X:%02X:%02X:%02X",
buf[0], buf[1], buf[2], buf[3], buf[4], buf[5]);
/* Check if MAC addr is owned by Schindler */
@@ -377,7 +377,7 @@
}
} else {
printf(LOG_PREFIX "Warning - Unable to read MAC from I2C"
- " device at address %02X:%04X\n", CFG_I2C_EEPROM,
+ " device at address %02X:%04X\n", CONFIG_SYS_I2C_EEPROM,
CONFIG_MAC_OFFSET);
}
#endif /* defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) */