rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
diff --git a/board/esd/tasreg/flash.c b/board/esd/tasreg/flash.c
index 13c07d2..ce905e9 100644
--- a/board/esd/tasreg/flash.c
+++ b/board/esd/tasreg/flash.c
@@ -45,13 +45,13 @@
int i;
/* Init: no FLASHes known */
- for (i=0; i<CFG_MAX_FLASH_BANKS; ++i) {
+ for (i=0; i<CONFIG_SYS_MAX_FLASH_BANKS; ++i) {
flash_info[i].flash_id = FLASH_UNKNOWN;
}
/* Static FLASH Bank configuration here - FIXME XXX */
- size_b0 = flash_get_size((vu_long *)CFG_FLASH_BASE, &flash_info[0]);
+ size_b0 = flash_get_size((vu_long *)CONFIG_SYS_FLASH_BASE, &flash_info[0]);
if (flash_info[0].flash_id == FLASH_UNKNOWN) {
printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
@@ -65,8 +65,8 @@
/* Monitor protection ON by default */
(void)flash_protect(FLAG_PROTECT_SET,
- CFG_FLASH_BASE,
- CFG_FLASH_BASE+CFG_MONITOR_LEN-1,
+ CONFIG_SYS_FLASH_BASE,
+ CONFIG_SYS_FLASH_BASE+CONFIG_SYS_MONITOR_LEN-1,
&flash_info[0]);
flash_info[0].size = size_b0;
diff --git a/board/esd/tasreg/tasreg.c b/board/esd/tasreg/tasreg.c
index fabb746..64e6d63 100644
--- a/board/esd/tasreg/tasreg.c
+++ b/board/esd/tasreg/tasreg.c
@@ -40,8 +40,8 @@
/* predefine these here for FPGA programming (before including fpga.c) */
#define SET_FPGA(data) mbar2_writeLong(MCFSIM_GPIO1_OUT, data)
-#define FPGA_DONE_STATE (mbar2_readLong(MCFSIM_GPIO1_READ) & CFG_FPGA_DONE)
-#define FPGA_INIT_STATE (mbar2_readLong(MCFSIM_GPIO1_READ) & CFG_FPGA_INIT)
+#define FPGA_DONE_STATE (mbar2_readLong(MCFSIM_GPIO1_READ) & CONFIG_SYS_FPGA_DONE)
+#define FPGA_INIT_STATE (mbar2_readLong(MCFSIM_GPIO1_READ) & CONFIG_SYS_FPGA_INIT)
#define FPGA_PROG_ACTIVE_HIGH /* on this platform is PROG active high! */
#define out32(a,b) /* nothing to do (gpio already configured) */
@@ -70,7 +70,7 @@
/*
* Set LED on
*/
- val = mbar2_readLong(MCFSIM_GPIO1_OUT) & ~CFG_GPIO1_LED;
+ val = mbar2_readLong(MCFSIM_GPIO1_OUT) & ~CONFIG_SYS_GPIO1_LED;
mbar2_writeLong(MCFSIM_GPIO1_OUT, val); /* Set LED on */
return 0;
@@ -85,13 +85,13 @@
* RC = ([(RefreshTime/#rows) / (1/BusClk)] / 16) - 1
*/
-#ifdef CFG_FAST_CLK
+#ifdef CONFIG_SYS_FAST_CLK
/*
* Busclk=70MHz, RefreshTime=64ms, #rows=4096 (4K)
* SO=1, NAM=0, COC=0, RTIM=01 (6clk refresh), RC=39
*/
mbar_writeShort(MCFSIM_DCR, 0x8239);
-#elif CFG_PLL_BYPASS
+#elif CONFIG_SYS_PLL_BYPASS
/*
* Busclk=5.6448MHz, RefreshTime=64ms, #rows=8192 (8K)
* SO=1, NAM=0, COC=0, RTIM=01 (6clk refresh), RC=02
@@ -129,7 +129,7 @@
mbar_writeLong(MCFSIM_DACR0, 0x0000b364); /* Enable DACR0[IMRS] (bit 6); RE remains enabled */
*((volatile unsigned long *) 0x800) = junk; /* Access RAM to initialize the mode register */
- return CFG_SDRAM_SIZE * 1024 * 1024;
+ return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
};
@@ -150,8 +150,8 @@
int i;
uchar buf[8];
- dst = malloc(CFG_FPGA_MAX_SIZE);
- if (gunzip (dst, CFG_FPGA_MAX_SIZE, (uchar *)fpgadata, &len) != 0) {
+ dst = malloc(CONFIG_SYS_FPGA_MAX_SIZE);
+ if (gunzip (dst, CONFIG_SYS_FPGA_MAX_SIZE, (uchar *)fpgadata, &len) != 0) {
printf ("GUNZIP ERROR - must RESET board to recover\n");
do_reset (NULL, 0, 0, NULL);
}