rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
diff --git a/board/sandburst/metrobox/metrobox.c b/board/sandburst/metrobox/metrobox.c
index c38850d..c3c4459 100644
--- a/board/sandburst/metrobox/metrobox.c
+++ b/board/sandburst/metrobox/metrobox.c
@@ -55,7 +55,7 @@
mtsdr(sdr_pfc0, 0x00103E00);
/* Setup access for LEDs, and system topology info */
- gpio_regs = (ppc440_gpio_regs_t *)CFG_GPIO_BASE;
+ gpio_regs = (ppc440_gpio_regs_t *)CONFIG_SYS_GPIO_BASE;
gpio_regs->open_drain = SBCOMMON_GPIO_SYS_LEDS;
gpio_regs->tri_state = SBCOMMON_GPIO_DBGLEDS;
@@ -83,7 +83,7 @@
EBC_BXAP_RE_DISABLED | EBC_BXAP_BEM_WRITEONLY |
EBC_BXAP_PEN_DISABLED);
- mtebc(pb0cr, EBC_BXCR_BAS_ENCODE(CFG_FLASH_BASE) |
+ mtebc(pb0cr, EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FLASH_BASE) |
EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT);
/*--------------------------------------------------------------------+
| 8KB NVRAM/RTC. Initialize bank 1 with default values.
@@ -246,7 +246,7 @@
unsigned char opto_rev, opto_id;
OPTO_FPGA_REGS_ST *opto_ps;
- opto_ps = (OPTO_FPGA_REGS_ST *)CFG_FPGA_BASE;
+ opto_ps = (OPTO_FPGA_REGS_ST *)CONFIG_SYS_FPGA_BASE;
opto_rev = (unsigned char)((opto_ps->revision_ul &
SAND_HAL_XC_XCVR_CNTL_REVISION_REVISION_MASK)
@@ -286,7 +286,7 @@
/* Fix the ack in the bme 32 */
udelay(5000);
- out32(CFG_BME32_BASE + 0x0000000C, 0x00000001);
+ out32(CONFIG_SYS_BME32_BASE + 0x0000000C, 0x00000001);
asm("eieio");
@@ -302,7 +302,7 @@
{
/* Turn on i2c bus 1 */
puts ("I2C1: ");
- i2c1_init (CFG_I2C_SPEED, CFG_I2C_SLAVE);
+ i2c1_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
puts ("ready\n");
/* Turn on fans */
@@ -323,7 +323,7 @@
unsigned char opto_rev;
OPTO_FPGA_REGS_ST *opto_ps;
- opto_ps = (OPTO_FPGA_REGS_ST *)CFG_FPGA_BASE;
+ opto_ps = (OPTO_FPGA_REGS_ST *)CONFIG_SYS_FPGA_BASE;
if(NULL != getenv("secondserial")) {
puts("secondserial is set, switching to second serial port\n");
@@ -387,7 +387,7 @@
void ide_set_reset(int on)
{
OPTO_FPGA_REGS_ST *opto_ps;
- opto_ps = (OPTO_FPGA_REGS_ST *)CFG_FPGA_BASE;
+ opto_ps = (OPTO_FPGA_REGS_ST *)CONFIG_SYS_FPGA_BASE;
if (on) { /* assert RESET */
opto_ps->reset_ul &= ~SAND_HAL_XC_XCVR_CNTL_RESET_CF_RESET_N_MASK;
@@ -412,7 +412,7 @@
/*
* Take appropriate hw bits out of reset
*/
- opto_ps = (OPTO_FPGA_REGS_ST *)CFG_FPGA_BASE;
+ opto_ps = (OPTO_FPGA_REGS_ST *)CONFIG_SYS_FPGA_BASE;
tmp =
SAND_HAL_XC_XCVR_CNTL_RESET_MAC1_RESET_N_MASK |