rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
diff --git a/cpu/mpc8xx/i2c.c b/cpu/mpc8xx/i2c.c
index f05b666..29c7c71 100644
--- a/cpu/mpc8xx/i2c.c
+++ b/cpu/mpc8xx/i2c.c
@@ -45,12 +45,12 @@
/*-----------------------------------------------------------------------
* Set default values
*/
-#ifndef CFG_I2C_SPEED
-#define CFG_I2C_SPEED 50000
+#ifndef CONFIG_SYS_I2C_SPEED
+#define CONFIG_SYS_I2C_SPEED 50000
#endif
-#ifndef CFG_I2C_SLAVE
-#define CFG_I2C_SLAVE 0xFE
+#ifndef CONFIG_SYS_I2C_SLAVE
+#define CONFIG_SYS_I2C_SLAVE 0xFE
#endif
/*-----------------------------------------------------------------------
*/
@@ -162,7 +162,7 @@
static int
i2c_setrate (int hz, int speed)
{
- immap_t *immap = (immap_t *) CFG_IMMR;
+ immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
volatile i2c8xx_t *i2c = (i2c8xx_t *) & immap->im_i2c;
int brgval,
modval, /* 0-3 */
@@ -207,7 +207,7 @@
void
i2c_init(int speed, int slaveaddr)
{
- volatile immap_t *immap = (immap_t *)CFG_IMMR ;
+ volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR ;
volatile cpm8xx_t *cp = (cpm8xx_t *)&immap->im_cpm;
volatile i2c8xx_t *i2c = (i2c8xx_t *)&immap->im_i2c;
volatile iic_t *iip = (iic_t *)&cp->cp_dparam[PROFF_IIC];
@@ -215,21 +215,21 @@
volatile I2C_BD *rxbd, *txbd;
uint dpaddr;
-#ifdef CFG_I2C_INIT_BOARD
+#ifdef CONFIG_SYS_I2C_INIT_BOARD
/* call board specific i2c bus reset routine before accessing the */
/* environment, which might be in a chip on that bus. For details */
/* about this problem see doc/I2C_Edge_Conditions. */
i2c_init_board();
#endif
-#ifdef CFG_I2C_UCODE_PATCH
+#ifdef CONFIG_SYS_I2C_UCODE_PATCH
iip = (iic_t *)&cp->cp_dpmem[iip->iic_rpbase];
#else
/* Disable relocation */
iip->iic_rpbase = 0;
#endif
-#ifdef CFG_ALLOC_DPRAM
+#ifdef CONFIG_SYS_ALLOC_DPRAM
dpaddr = iip->iic_rbase;
if (dpaddr == 0) {
/* need to allocate dual port ram */
@@ -269,7 +269,7 @@
* divide BRGCLK by 1)
*/
PRINTD(("[I2C] Setting rate...\n"));
- i2c_setrate (gd->cpu_clk, CFG_I2C_SPEED) ;
+ i2c_setrate (gd->cpu_clk, CONFIG_SYS_I2C_SPEED) ;
/* Set I2C controller in master mode */
i2c->i2c_i2com = 0x01;
@@ -295,7 +295,7 @@
/* Set maximum receive size. */
iip->iic_mrblr = I2C_RXTX_LEN;
-#ifdef CFG_I2C_UCODE_PATCH
+#ifdef CONFIG_SYS_I2C_UCODE_PATCH
/*
* Initialize required parameters if using microcode patch.
*/
@@ -318,13 +318,13 @@
static void
i2c_newio(i2c_state_t *state)
{
- volatile immap_t *immap = (immap_t *)CFG_IMMR ;
+ volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR ;
volatile cpm8xx_t *cp = (cpm8xx_t *)&immap->im_cpm;
volatile iic_t *iip = (iic_t *)&cp->cp_dparam[PROFF_IIC];
PRINTD(("[I2C] i2c_newio\n"));
-#ifdef CFG_I2C_UCODE_PATCH
+#ifdef CONFIG_SYS_I2C_UCODE_PATCH
iip = (iic_t *)&cp->cp_dpmem[iip->iic_rpbase];
#endif
state->rx_idx = 0;
@@ -492,7 +492,7 @@
static int i2c_doio(i2c_state_t *state)
{
- volatile immap_t *immap = (immap_t *)CFG_IMMR ;
+ volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR ;
volatile cpm8xx_t *cp = (cpm8xx_t *)&immap->im_cpm;
volatile i2c8xx_t *i2c = (i2c8xx_t *)&immap->im_i2c;
volatile iic_t *iip = (iic_t *)&cp->cp_dparam[PROFF_IIC];
@@ -501,7 +501,7 @@
PRINTD(("[I2C] i2c_doio\n"));
-#ifdef CFG_I2C_UCODE_PATCH
+#ifdef CONFIG_SYS_I2C_UCODE_PATCH
iip = (iic_t *)&cp->cp_dpmem[iip->iic_rpbase];
#endif
@@ -593,7 +593,7 @@
int rc;
uchar buf[1];
- i2c_init(CFG_I2C_SPEED, CFG_I2C_SLAVE);
+ i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
i2c_newio(&state);
@@ -628,7 +628,7 @@
xaddr[2] = (addr >> 8) & 0xFF;
xaddr[3] = addr & 0xFF;
-#ifdef CFG_I2C_EEPROM_ADDR_OVERFLOW
+#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
/*
* EEPROM chips that implement "address overflow" are ones like
* Catalyst 24WC04/08/16 which has 9/10/11 bits of address and the
@@ -639,7 +639,7 @@
* be one byte because the extra address bits are hidden in the
* chip address.
*/
- chip |= ((addr >> (alen * 8)) & CFG_I2C_EEPROM_ADDR_OVERFLOW);
+ chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
#endif
i2c_newio(&state);
@@ -678,7 +678,7 @@
xaddr[2] = (addr >> 8) & 0xFF;
xaddr[3] = addr & 0xFF;
-#ifdef CFG_I2C_EEPROM_ADDR_OVERFLOW
+#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
/*
* EEPROM chips that implement "address overflow" are ones like
* Catalyst 24WC04/08/16 which has 9/10/11 bits of address and the
@@ -689,7 +689,7 @@
* be one byte because the extra address bits are hidden in the
* chip address.
*/
- chip |= ((addr >> (alen * 8)) & CFG_I2C_EEPROM_ADDR_OVERFLOW);
+ chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
#endif
i2c_newio(&state);
@@ -722,7 +722,7 @@
{
uchar buf;
- i2c_init(CFG_I2C_SPEED, CFG_I2C_SLAVE);
+ i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
i2c_read(i2c_addr, reg, 1, &buf, 1);
@@ -732,7 +732,7 @@
void
i2c_reg_write(uchar i2c_addr, uchar reg, uchar val)
{
- i2c_init(CFG_I2C_SPEED, CFG_I2C_SLAVE);
+ i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
i2c_write(i2c_addr, reg, 1, &val, 1);
}