rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
diff --git a/include/configs/davinci_schmoogie.h b/include/configs/davinci_schmoogie.h
index 016a897..8d7bcf5 100644
--- a/include/configs/davinci_schmoogie.h
+++ b/include/configs/davinci_schmoogie.h
@@ -25,23 +25,23 @@
/* Board */
/*=======*/
#define SCHMOOGIE
-#define CFG_NAND_LARGEPAGE
-#define CFG_USE_NAND
+#define CONFIG_SYS_NAND_LARGEPAGE
+#define CONFIG_SYS_USE_NAND
/*===================*/
/* SoC Configuration */
/*===================*/
#define CONFIG_ARM926EJS /* arm926ejs CPU core */
#define CONFIG_SYS_CLK_FREQ 297000000 /* Arm Clock frequency */
-#define CFG_TIMERBASE 0x01c21400 /* use timer 0 */
-#define CFG_HZ_CLOCK 27000000 /* Timer Input clock freq */
-#define CFG_HZ 1000
+#define CONFIG_SYS_TIMERBASE 0x01c21400 /* use timer 0 */
+#define CONFIG_SYS_HZ_CLOCK 27000000 /* Timer Input clock freq */
+#define CONFIG_SYS_HZ 1000
/*=============*/
/* Memory Info */
/*=============*/
-#define CFG_MALLOC_LEN (0x10000 + 256*1024) /* malloc() len */
-#define CFG_GBL_DATA_SIZE 128 /* reserved for initial data */
-#define CFG_MEMTEST_START 0x80000000 /* memtest start address */
-#define CFG_MEMTEST_END 0x81000000 /* 16MB RAM test */
+#define CONFIG_SYS_MALLOC_LEN (0x10000 + 256*1024) /* malloc() len */
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* reserved for initial data */
+#define CONFIG_SYS_MEMTEST_START 0x80000000 /* memtest start address */
+#define CONFIG_SYS_MEMTEST_END 0x81000000 /* 16MB RAM test */
#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
#define CONFIG_STACKSIZE (256*1024) /* regular stack */
#define PHYS_SDRAM_1 0x80000000 /* DDR Start */
@@ -50,21 +50,21 @@
/*====================*/
/* Serial Driver info */
/*====================*/
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE 4 /* NS16550 register size */
-#define CFG_NS16550_COM1 0x01c20000 /* Base address of UART0 */
-#define CFG_NS16550_CLK 27000000 /* Input clock to NS16550 */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 4 /* NS16550 register size */
+#define CONFIG_SYS_NS16550_COM1 0x01c20000 /* Base address of UART0 */
+#define CONFIG_SYS_NS16550_CLK 27000000 /* Input clock to NS16550 */
#define CONFIG_CONS_INDEX 1 /* use UART0 for console */
#define CONFIG_BAUDRATE 115200 /* Default baud rate */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*===================*/
/* I2C Configuration */
/*===================*/
#define CONFIG_HARD_I2C
#define CONFIG_DRIVER_DAVINCI_I2C
-#define CFG_I2C_SPEED 80000 /* 100Kbps won't work, silicon bug */
-#define CFG_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */
+#define CONFIG_SYS_I2C_SPEED 80000 /* 100Kbps won't work, silicon bug */
+#define CONFIG_SYS_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */
/*==================================*/
/* Network & Ethernet Configuration */
/*==================================*/
@@ -80,25 +80,25 @@
/* Flash & Environment */
/*=====================*/
#undef CONFIG_ENV_IS_IN_FLASH
-#define CFG_NO_FLASH
+#define CONFIG_SYS_NO_FLASH
#define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */
#define CONFIG_ENV_SECT_SIZE 2048 /* Env sector Size */
#define CONFIG_ENV_SIZE SZ_128K
#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */
#define CONFIG_SKIP_RELOCATE_UBOOT /* to a proper address, init done */
-#define CFG_NAND_BASE 0x02000000
-#define CFG_NAND_HW_ECC
-#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
+#define CONFIG_SYS_NAND_BASE 0x02000000
+#define CONFIG_SYS_NAND_HW_ECC
+#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define NAND_MAX_CHIPS 1
#define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */
/*=====================*/
/* Board related stuff */
/*=====================*/
#define CONFIG_RTC_DS1307 /* RTC chip on SCHMOOGIE */
-#define CFG_I2C_RTC_ADDR 0x6f /* RTC chip I2C address */
+#define CONFIG_SYS_I2C_RTC_ADDR 0x6f /* RTC chip I2C address */
#define CONFIG_HAS_UID
#define CONFIG_UID_DS28CM00 /* Unique ID on SCHMOOGIE */
-#define CFG_UID_ADDR 0x50 /* UID chip I2C address */
+#define CONFIG_SYS_UID_ADDR 0x50 /* UID chip I2C address */
/*==============================*/
/* U-Boot general configuration */
/*==============================*/
@@ -106,18 +106,18 @@
#define CONFIG_MISC_INIT_R
#undef CONFIG_BOOTDELAY
#define CONFIG_BOOTFILE "uImage" /* Boot file name */
-#define CFG_PROMPT "U-Boot > " /* Monitor Command Prompt */
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print buffer sz */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_LOAD_ADDR 0x80700000 /* default Linux kernel load address */
+#define CONFIG_SYS_PROMPT "U-Boot > " /* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print buffer sz */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_LOAD_ADDR 0x80700000 /* default Linux kernel load address */
#define CONFIG_VERSION_VARIABLE
#define CONFIG_AUTO_COMPLETE /* Won't work with hush so far, may be later */
-#define CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_CMDLINE_EDITING
-#define CFG_LONGHELP
+#define CONFIG_SYS_LONGHELP
#define CONFIG_CRC32_VERIFY
#define CONFIG_MX_CYCLIC
/*===================*/