rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h
index 58918d4..237a9c5 100644
--- a/include/configs/kilauea.h
+++ b/include/configs/kilauea.h
@@ -53,10 +53,10 @@
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_FLASH_BASE 0xFC000000
-#define CFG_NAND_ADDR 0xF8000000
-#define CFG_FPGA_BASE 0xF0000000
-#define CFG_PERIPHERAL_BASE 0xEF600000 /* internal peripherals*/
+#define CONFIG_SYS_FLASH_BASE 0xFC000000
+#define CONFIG_SYS_NAND_ADDR 0xF8000000
+#define CONFIG_SYS_FPGA_BASE 0xF0000000
+#define CONFIG_SYS_PERIPHERAL_BASE 0xEF600000 /* internal peripherals*/
/*-----------------------------------------------------------------------
* Initial RAM & Stack Pointer Configuration Options
@@ -72,25 +72,25 @@
* the latter of which is less than desireable since it requires
* setting up the SDRAM and ECC in assembly code.
*
- * To use (2), define 'CFG_INIT_DCACHE_CS' to be an unused chip
+ * To use (2), define 'CONFIG_SYS_INIT_DCACHE_CS' to be an unused chip
* select on the External Bus Controller (EBC) and then select a
- * value for 'CFG_INIT_RAM_ADDR' outside of the range of valid,
- * physical SDRAM. Otherwise, undefine 'CFG_INIT_DCACHE_CS' and
- * select a value for 'CFG_INIT_RAM_ADDR' within the range of valid,
+ * value for 'CONFIG_SYS_INIT_RAM_ADDR' outside of the range of valid,
+ * physical SDRAM. Otherwise, undefine 'CONFIG_SYS_INIT_DCACHE_CS' and
+ * select a value for 'CONFIG_SYS_INIT_RAM_ADDR' within the range of valid,
* physical SDRAM to use (3).
*-----------------------------------------------------------------------*/
-#define CFG_INIT_DCACHE_CS 4
+#define CONFIG_SYS_INIT_DCACHE_CS 4
-#if defined(CFG_INIT_DCACHE_CS)
-#define CFG_INIT_RAM_ADDR (CFG_SDRAM_BASE + ( 1 << 30)) /* 1 GiB */
+#if defined(CONFIG_SYS_INIT_DCACHE_CS)
+#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_SDRAM_BASE + ( 1 << 30)) /* 1 GiB */
#else
-#define CFG_INIT_RAM_ADDR (CFG_SDRAM_BASE + (32 << 20)) /* 32 MiB */
-#endif /* defined(CFG_INIT_DCACHE_CS) */
+#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_SDRAM_BASE + (32 << 20)) /* 32 MiB */
+#endif /* defined(CONFIG_SYS_INIT_DCACHE_CS) */
-#define CFG_INIT_RAM_END (4 << 10) /* 4 KiB */
-#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_END (4 << 10) /* 4 KiB */
+#define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
/*
* If the data cache is being used for the primordial stack and global
@@ -100,20 +100,20 @@
* for the POST word.
*/
-#if defined(CFG_INIT_DCACHE_CS)
-# define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-# define CFG_POST_ALT_WORD_ADDR (CFG_PERIPHERAL_BASE + GPT0_COMP6)
+#if defined(CONFIG_SYS_INIT_DCACHE_CS)
+# define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+# define CONFIG_SYS_POST_ALT_WORD_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_COMP6)
#else
-# define CFG_INIT_EXTRA_SIZE 16
-# define CFG_INIT_SP_OFFSET (CFG_GBL_DATA_OFFSET - CFG_INIT_EXTRA_SIZE)
-# define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 4)
-# define CFG_OCM_DATA_ADDR CFG_INIT_RAM_ADDR
-#endif /* defined(CFG_INIT_DCACHE_CS) */
+# define CONFIG_SYS_INIT_EXTRA_SIZE 16
+# define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - CONFIG_SYS_INIT_EXTRA_SIZE)
+# define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 4)
+# define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_INIT_RAM_ADDR
+#endif /* defined(CONFIG_SYS_INIT_DCACHE_CS) */
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
-#define CFG_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */
+#define CONFIG_SYS_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */
/* define this if you want console on UART1 */
#undef CONFIG_UART1_CONSOLE
@@ -130,22 +130,22 @@
/*-----------------------------------------------------------------------
* FLASH related
*----------------------------------------------------------------------*/
-#define CFG_FLASH_CFI /* The flash is CFI compatible */
+#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
-#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE}
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE}
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#ifdef CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
-#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
@@ -171,57 +171,57 @@
* set up. While still running from location 0xfffff000...0xffffffff the
* NAND controller cannot be accessed since it is attached to CS0 too.
*/
-#define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */
-#define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */
-#define CFG_NAND_BOOT_SPL_DST 0x00800000 /* Copy SPL here */
-#define CFG_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */
-#define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start NUB from this addr */
-#define CFG_NAND_BOOT_SPL_DELTA (CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)
+#define CONFIG_SYS_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */
+#define CONFIG_SYS_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */
+#define CONFIG_SYS_NAND_BOOT_SPL_DST 0x00800000 /* Copy SPL here */
+#define CONFIG_SYS_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST /* Start NUB from this addr */
+#define CONFIG_SYS_NAND_BOOT_SPL_DELTA (CONFIG_SYS_NAND_BOOT_SPL_SRC - CONFIG_SYS_NAND_BOOT_SPL_DST)
/*
* Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
*/
-#define CFG_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */
-#define CFG_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */
+#define CONFIG_SYS_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */
+#define CONFIG_SYS_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */
/*
* Now the NAND chip has to be defined (no autodetection used!)
*/
-#define CFG_NAND_PAGE_SIZE 512 /* NAND chip page size */
-#define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */
-#define CFG_NAND_PAGE_COUNT 32 /* NAND chip page count */
-#define CFG_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */
-#define CFG_NAND_4_ADDR_CYCLE 1 /* Fourth addr used (>32MB) */
+#define CONFIG_SYS_NAND_PAGE_SIZE 512 /* NAND chip page size */
+#define CONFIG_SYS_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */
+#define CONFIG_SYS_NAND_PAGE_COUNT 32 /* NAND chip page count */
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */
+#define CONFIG_SYS_NAND_4_ADDR_CYCLE 1 /* Fourth addr used (>32MB) */
-#define CFG_NAND_ECCSIZE 256
-#define CFG_NAND_ECCBYTES 3
-#define CFG_NAND_ECCSTEPS (CFG_NAND_PAGE_SIZE / CFG_NAND_ECCSIZE)
-#define CFG_NAND_OOBSIZE 16
-#define CFG_NAND_ECCTOTAL (CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS)
-#define CFG_NAND_ECCPOS {0, 1, 2, 3, 6, 7}
+#define CONFIG_SYS_NAND_ECCSIZE 256
+#define CONFIG_SYS_NAND_ECCBYTES 3
+#define CONFIG_SYS_NAND_ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / CONFIG_SYS_NAND_ECCSIZE)
+#define CONFIG_SYS_NAND_OOBSIZE 16
+#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * CONFIG_SYS_NAND_ECCSTEPS)
+#define CONFIG_SYS_NAND_ECCPOS {0, 1, 2, 3, 6, 7}
#ifdef CONFIG_ENV_IS_IN_NAND
/*
* For NAND booting the environment is embedded in the U-Boot image. Please take
* look at the file board/amcc/sequoia/u-boot-nand.lds for details.
*/
-#define CONFIG_ENV_SIZE CFG_NAND_BLOCK_SIZE
-#define CONFIG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE)
+#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE)
#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
#endif
/*-----------------------------------------------------------------------
* NAND FLASH
*----------------------------------------------------------------------*/
-#define CFG_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define NAND_MAX_CHIPS 1
-#define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS)
-#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
+#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_ADDR + CONFIG_SYS_NAND_CS)
+#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
/*-----------------------------------------------------------------------
* DDR SDRAM
*----------------------------------------------------------------------*/
-#define CFG_MBYTES_SDRAM (256) /* 256MB */
+#define CONFIG_SYS_MBYTES_SDRAM (256) /* 256MB */
/*
* CONFIG_PPC4xx_DDR_AUTOCALIBRATION
@@ -239,55 +239,55 @@
#define DEBUG_PPC4xx_DDR_AUTOCALIBRATION /* dynamic DDR autocal debug */
#undef CONFIG_PPC4xx_DDR_METHOD_A
-#define CFG_SDRAM0_MB0CF_BASE (( 0 << 20) + CFG_SDRAM_BASE)
+#define CONFIG_SYS_SDRAM0_MB0CF_BASE (( 0 << 20) + CONFIG_SYS_SDRAM_BASE)
/* DDR1/2 SDRAM Device Control Register Data Values */
-#define CFG_SDRAM0_MB0CF ((CFG_SDRAM0_MB0CF_BASE >> 3) | \
+#define CONFIG_SYS_SDRAM0_MB0CF ((CONFIG_SYS_SDRAM0_MB0CF_BASE >> 3) | \
SDRAM_RXBAS_SDSZ_256MB | \
SDRAM_RXBAS_SDAM_MODE7 | \
SDRAM_RXBAS_SDBE_ENABLE)
-#define CFG_SDRAM0_MB1CF SDRAM_RXBAS_SDBE_DISABLE
-#define CFG_SDRAM0_MB2CF SDRAM_RXBAS_SDBE_DISABLE
-#define CFG_SDRAM0_MB3CF SDRAM_RXBAS_SDBE_DISABLE
-#define CFG_SDRAM0_MCOPT1 (SDRAM_MCOPT1_PMU_OPEN | \
+#define CONFIG_SYS_SDRAM0_MB1CF SDRAM_RXBAS_SDBE_DISABLE
+#define CONFIG_SYS_SDRAM0_MB2CF SDRAM_RXBAS_SDBE_DISABLE
+#define CONFIG_SYS_SDRAM0_MB3CF SDRAM_RXBAS_SDBE_DISABLE
+#define CONFIG_SYS_SDRAM0_MCOPT1 (SDRAM_MCOPT1_PMU_OPEN | \
SDRAM_MCOPT1_8_BANKS | \
SDRAM_MCOPT1_DDR2_TYPE | \
SDRAM_MCOPT1_QDEP | \
SDRAM_MCOPT1_DCOO_DISABLED)
-#define CFG_SDRAM0_MCOPT2 0x00000000
-#define CFG_SDRAM0_MODT0 (SDRAM_MODT_EB0W_ENABLE | \
+#define CONFIG_SYS_SDRAM0_MCOPT2 0x00000000
+#define CONFIG_SYS_SDRAM0_MODT0 (SDRAM_MODT_EB0W_ENABLE | \
SDRAM_MODT_EB0R_ENABLE)
-#define CFG_SDRAM0_MODT1 0x00000000
-#define CFG_SDRAM0_CODT (SDRAM_CODT_RK0R_ON | \
+#define CONFIG_SYS_SDRAM0_MODT1 0x00000000
+#define CONFIG_SYS_SDRAM0_CODT (SDRAM_CODT_RK0R_ON | \
SDRAM_CODT_CKLZ_36OHM | \
SDRAM_CODT_DQS_1_8_V_DDR2 | \
SDRAM_CODT_IO_NMODE)
-#define CFG_SDRAM0_RTR SDRAM_RTR_RINT_ENCODE(1560)
-#define CFG_SDRAM0_INITPLR0 (SDRAM_INITPLR_ENABLE | \
+#define CONFIG_SYS_SDRAM0_RTR SDRAM_RTR_RINT_ENCODE(1560)
+#define CONFIG_SYS_SDRAM0_INITPLR0 (SDRAM_INITPLR_ENABLE | \
SDRAM_INITPLR_IMWT_ENCODE(80) | \
SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_NOP))
-#define CFG_SDRAM0_INITPLR1 (SDRAM_INITPLR_ENABLE | \
+#define CONFIG_SYS_SDRAM0_INITPLR1 (SDRAM_INITPLR_ENABLE | \
SDRAM_INITPLR_IMWT_ENCODE(3) | \
SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_PRECHARGE) | \
SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_MR) | \
SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_PRECHARGE_ALL))
-#define CFG_SDRAM0_INITPLR2 (SDRAM_INITPLR_ENABLE | \
+#define CONFIG_SYS_SDRAM0_INITPLR2 (SDRAM_INITPLR_ENABLE | \
SDRAM_INITPLR_IMWT_ENCODE(2) | \
SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \
SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR2) | \
SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_EMR2_TEMP_COMMERCIAL))
-#define CFG_SDRAM0_INITPLR3 (SDRAM_INITPLR_ENABLE | \
+#define CONFIG_SYS_SDRAM0_INITPLR3 (SDRAM_INITPLR_ENABLE | \
SDRAM_INITPLR_IMWT_ENCODE(2) | \
SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \
SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR3) | \
SDRAM_INITPLR_IMA_ENCODE(0))
-#define CFG_SDRAM0_INITPLR4 (SDRAM_INITPLR_ENABLE | \
+#define CONFIG_SYS_SDRAM0_INITPLR4 (SDRAM_INITPLR_ENABLE | \
SDRAM_INITPLR_IMWT_ENCODE(2) | \
SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \
SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR) | \
SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_EMR_DQS_DISABLE | \
JEDEC_MA_EMR_RTT_75OHM))
-#define CFG_SDRAM0_INITPLR5 (SDRAM_INITPLR_ENABLE | \
+#define CONFIG_SYS_SDRAM0_INITPLR5 (SDRAM_INITPLR_ENABLE | \
SDRAM_INITPLR_IMWT_ENCODE(2) | \
SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \
SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_MR) | \
@@ -295,31 +295,31 @@
JEDEC_MA_MR_CL_DDR2_4_0_CLK | \
JEDEC_MA_MR_BLEN_4 | \
JEDEC_MA_MR_DLL_RESET))
-#define CFG_SDRAM0_INITPLR6 (SDRAM_INITPLR_ENABLE | \
+#define CONFIG_SYS_SDRAM0_INITPLR6 (SDRAM_INITPLR_ENABLE | \
SDRAM_INITPLR_IMWT_ENCODE(3) | \
SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_PRECHARGE) | \
SDRAM_INITPLR_IBA_ENCODE(0x0) | \
SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_PRECHARGE_ALL))
-#define CFG_SDRAM0_INITPLR7 (SDRAM_INITPLR_ENABLE | \
+#define CONFIG_SYS_SDRAM0_INITPLR7 (SDRAM_INITPLR_ENABLE | \
SDRAM_INITPLR_IMWT_ENCODE(26) | \
SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH))
-#define CFG_SDRAM0_INITPLR8 (SDRAM_INITPLR_ENABLE | \
+#define CONFIG_SYS_SDRAM0_INITPLR8 (SDRAM_INITPLR_ENABLE | \
SDRAM_INITPLR_IMWT_ENCODE(26) | \
SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH))
-#define CFG_SDRAM0_INITPLR9 (SDRAM_INITPLR_ENABLE | \
+#define CONFIG_SYS_SDRAM0_INITPLR9 (SDRAM_INITPLR_ENABLE | \
SDRAM_INITPLR_IMWT_ENCODE(26) | \
SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH))
-#define CFG_SDRAM0_INITPLR10 (SDRAM_INITPLR_ENABLE | \
+#define CONFIG_SYS_SDRAM0_INITPLR10 (SDRAM_INITPLR_ENABLE | \
SDRAM_INITPLR_IMWT_ENCODE(26) | \
SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH))
-#define CFG_SDRAM0_INITPLR11 (SDRAM_INITPLR_ENABLE | \
+#define CONFIG_SYS_SDRAM0_INITPLR11 (SDRAM_INITPLR_ENABLE | \
SDRAM_INITPLR_IMWT_ENCODE(2) | \
SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \
SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_MR) | \
SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_MR_WR_DDR2_3_CYC | \
JEDEC_MA_MR_CL_DDR2_4_0_CLK | \
JEDEC_MA_MR_BLEN_4))
-#define CFG_SDRAM0_INITPLR12 (SDRAM_INITPLR_ENABLE | \
+#define CONFIG_SYS_SDRAM0_INITPLR12 (SDRAM_INITPLR_ENABLE | \
SDRAM_INITPLR_IMWT_ENCODE(2) | \
SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \
SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR) | \
@@ -328,7 +328,7 @@
JEDEC_MA_EMR_DQS_DISABLE | \
JEDEC_MA_EMR_RTT_DISABLED | \
JEDEC_MA_EMR_ODS_NORMAL))
-#define CFG_SDRAM0_INITPLR13 (SDRAM_INITPLR_ENABLE | \
+#define CONFIG_SYS_SDRAM0_INITPLR13 (SDRAM_INITPLR_ENABLE | \
SDRAM_INITPLR_IMWT_ENCODE(2) | \
SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \
SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR) | \
@@ -337,54 +337,54 @@
JEDEC_MA_EMR_DQS_DISABLE | \
JEDEC_MA_EMR_RTT_DISABLED | \
JEDEC_MA_EMR_ODS_NORMAL))
-#define CFG_SDRAM0_INITPLR14 (SDRAM_INITPLR_DISABLE)
-#define CFG_SDRAM0_INITPLR15 (SDRAM_INITPLR_DISABLE)
-#define CFG_SDRAM0_RQDC (SDRAM_RQDC_RQDE_ENABLE | \
+#define CONFIG_SYS_SDRAM0_INITPLR14 (SDRAM_INITPLR_DISABLE)
+#define CONFIG_SYS_SDRAM0_INITPLR15 (SDRAM_INITPLR_DISABLE)
+#define CONFIG_SYS_SDRAM0_RQDC (SDRAM_RQDC_RQDE_ENABLE | \
SDRAM_RQDC_RQFD_ENCODE(56))
-#define CFG_SDRAM0_RFDC SDRAM_RFDC_RFFD_ENCODE(521)
-#define CFG_SDRAM0_RDCC (SDRAM_RDCC_RDSS_T2)
-#define CFG_SDRAM0_DLCR (SDRAM_DLCR_DCLM_AUTO | \
+#define CONFIG_SYS_SDRAM0_RFDC SDRAM_RFDC_RFFD_ENCODE(521)
+#define CONFIG_SYS_SDRAM0_RDCC (SDRAM_RDCC_RDSS_T2)
+#define CONFIG_SYS_SDRAM0_DLCR (SDRAM_DLCR_DCLM_AUTO | \
SDRAM_DLCR_DLCS_CONT_DONE | \
SDRAM_DLCR_DLCV_ENCODE(165))
-#define CFG_SDRAM0_CLKTR (SDRAM_CLKTR_CLKP_180_DEG_ADV)
-#define CFG_SDRAM0_WRDTR 0x00000000
-#define CFG_SDRAM0_SDTR1 (SDRAM_SDTR1_LDOF_2_CLK | \
+#define CONFIG_SYS_SDRAM0_CLKTR (SDRAM_CLKTR_CLKP_180_DEG_ADV)
+#define CONFIG_SYS_SDRAM0_WRDTR 0x00000000
+#define CONFIG_SYS_SDRAM0_SDTR1 (SDRAM_SDTR1_LDOF_2_CLK | \
SDRAM_SDTR1_RTW_2_CLK | \
SDRAM_SDTR1_RTRO_1_CLK)
-#define CFG_SDRAM0_SDTR2 (SDRAM_SDTR2_RCD_3_CLK | \
+#define CONFIG_SYS_SDRAM0_SDTR2 (SDRAM_SDTR2_RCD_3_CLK | \
SDRAM_SDTR2_WTR_2_CLK | \
SDRAM_SDTR2_XSNR_32_CLK | \
SDRAM_SDTR2_WPC_4_CLK | \
SDRAM_SDTR2_RPC_2_CLK | \
SDRAM_SDTR2_RP_3_CLK | \
SDRAM_SDTR2_RRD_2_CLK)
-#define CFG_SDRAM0_SDTR3 (SDRAM_SDTR3_RAS_ENCODE(8) | \
+#define CONFIG_SYS_SDRAM0_SDTR3 (SDRAM_SDTR3_RAS_ENCODE(8) | \
SDRAM_SDTR3_RC_ENCODE(11) | \
SDRAM_SDTR3_XCS | \
SDRAM_SDTR3_RFC_ENCODE(26))
-#define CFG_SDRAM0_MMODE (SDRAM_MMODE_WR_DDR2_3_CYC | \
+#define CONFIG_SYS_SDRAM0_MMODE (SDRAM_MMODE_WR_DDR2_3_CYC | \
SDRAM_MMODE_DCL_DDR2_4_0_CLK | \
SDRAM_MMODE_BLEN_4)
-#define CFG_SDRAM0_MEMODE (SDRAM_MEMODE_DQS_DISABLE | \
+#define CONFIG_SYS_SDRAM0_MEMODE (SDRAM_MEMODE_DQS_DISABLE | \
SDRAM_MEMODE_RTT_75OHM)
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */
-#define CFG_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */
-#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
/* Standard DTT sensor configuration */
#define CONFIG_DTT_DS1775 1
#define CONFIG_DTT_SENSORS { 0 }
-#define CFG_I2C_DTT_ADDR 0x48
+#define CONFIG_SYS_I2C_DTT_ADDR 0x48
/* RTC configuration */
#define CONFIG_RTC_DS1338 1
-#define CFG_I2C_RTC_ADDR 0x68
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
/*-----------------------------------------------------------------------
* Ethernet
@@ -432,20 +432,20 @@
#define CONFIG_CMD_SNTP
/* POST support */
-#define CONFIG_POST (CFG_POST_CACHE | \
- CFG_POST_CPU | \
- CFG_POST_ETHER | \
- CFG_POST_I2C | \
- CFG_POST_MEMORY | \
- CFG_POST_UART)
+#define CONFIG_POST (CONFIG_SYS_POST_CACHE | \
+ CONFIG_SYS_POST_CPU | \
+ CONFIG_SYS_POST_ETHER | \
+ CONFIG_SYS_POST_I2C | \
+ CONFIG_SYS_POST_MEMORY | \
+ CONFIG_SYS_POST_UART)
/* Define here the base-addresses of the UARTs to test in POST */
-#define CFG_POST_UART_TABLE {UART0_BASE, UART1_BASE}
+#define CONFIG_SYS_POST_UART_TABLE {UART0_BASE, UART1_BASE}
#define CONFIG_LOGBUFFER
-#define CFG_POST_CACHE_ADDR 0x00800000 /* free virtual address */
+#define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */
-#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
/*-----------------------------------------------------------------------
* PCI stuff
@@ -458,59 +458,59 @@
/*-----------------------------------------------------------------------
* PCIe stuff
*----------------------------------------------------------------------*/
-#define CFG_PCIE_MEMBASE 0x90000000 /* mapped PCIe memory */
-#define CFG_PCIE_MEMSIZE 0x08000000 /* 128 Meg, smallest incr per port */
+#define CONFIG_SYS_PCIE_MEMBASE 0x90000000 /* mapped PCIe memory */
+#define CONFIG_SYS_PCIE_MEMSIZE 0x08000000 /* 128 Meg, smallest incr per port */
-#define CFG_PCIE0_CFGBASE 0xa0000000 /* remote access */
-#define CFG_PCIE0_XCFGBASE 0xb0000000 /* local access */
-#define CFG_PCIE0_CFGMASK 0xe0000001 /* 512 Meg */
+#define CONFIG_SYS_PCIE0_CFGBASE 0xa0000000 /* remote access */
+#define CONFIG_SYS_PCIE0_XCFGBASE 0xb0000000 /* local access */
+#define CONFIG_SYS_PCIE0_CFGMASK 0xe0000001 /* 512 Meg */
-#define CFG_PCIE1_CFGBASE 0xc0000000 /* remote access */
-#define CFG_PCIE1_XCFGBASE 0xd0000000 /* local access */
-#define CFG_PCIE1_CFGMASK 0xe0000001 /* 512 Meg */
+#define CONFIG_SYS_PCIE1_CFGBASE 0xc0000000 /* remote access */
+#define CONFIG_SYS_PCIE1_XCFGBASE 0xd0000000 /* local access */
+#define CONFIG_SYS_PCIE1_CFGMASK 0xe0000001 /* 512 Meg */
-#define CFG_PCIE0_UTLBASE 0xef502000
-#define CFG_PCIE1_UTLBASE 0xef503000
+#define CONFIG_SYS_PCIE0_UTLBASE 0xef502000
+#define CONFIG_SYS_PCIE1_UTLBASE 0xef503000
/* base address of inbound PCIe window */
-#define CFG_PCIE_INBOUND_BASE 0x0000000000000000ULL
+#define CONFIG_SYS_PCIE_INBOUND_BASE 0x0000000000000000ULL
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*----------------------------------------------------------------------*/
#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
/* booting from NAND, so NAND chips select has to be on CS 0 */
-#define CFG_NAND_CS 0 /* NAND chip connected to CSx */
+#define CONFIG_SYS_NAND_CS 0 /* NAND chip connected to CSx */
/* Memory Bank 1 (NOR-FLASH) initialization */
-#define CFG_EBC_PB1AP 0x05806500
-#define CFG_EBC_PB1CR 0xFC0DA000 /* BAS=0xFC0,BS=64MB,BU=R/W,BW=16bit*/
+#define CONFIG_SYS_EBC_PB1AP 0x05806500
+#define CONFIG_SYS_EBC_PB1CR 0xFC0DA000 /* BAS=0xFC0,BS=64MB,BU=R/W,BW=16bit*/
/* Memory Bank 0 (NAND-FLASH) initialization */
-#define CFG_EBC_PB0AP 0x018003c0
-#define CFG_EBC_PB0CR (CFG_NAND_ADDR | 0x1e000)
+#define CONFIG_SYS_EBC_PB0AP 0x018003c0
+#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_NAND_ADDR | 0x1e000)
#else
-#define CFG_NAND_CS 1 /* NAND chip connected to CSx */
+#define CONFIG_SYS_NAND_CS 1 /* NAND chip connected to CSx */
/* Memory Bank 0 (NOR-FLASH) initialization */
-#define CFG_EBC_PB0AP 0x05806500
-#define CFG_EBC_PB0CR 0xFC0DA000 /* BAS=0xFC0,BS=64MB,BU=R/W,BW=16bit*/
+#define CONFIG_SYS_EBC_PB0AP 0x05806500
+#define CONFIG_SYS_EBC_PB0CR 0xFC0DA000 /* BAS=0xFC0,BS=64MB,BU=R/W,BW=16bit*/
/* Memory Bank 1 (NAND-FLASH) initialization */
-#define CFG_EBC_PB1AP 0x018003c0
-#define CFG_EBC_PB1CR (CFG_NAND_ADDR | 0x1e000)
+#define CONFIG_SYS_EBC_PB1AP 0x018003c0
+#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_NAND_ADDR | 0x1e000)
#endif
/* Memory Bank 2 (FPGA) initialization */
-#define CFG_EBC_PB2AP 0x9400C800
-#define CFG_EBC_PB2CR (CFG_FPGA_BASE | 0x18000)
+#define CONFIG_SYS_EBC_PB2AP 0x9400C800
+#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_FPGA_BASE | 0x18000)
-#define CFG_EBC_CFG 0x7FC00000 /* EBC0_CFG */
+#define CONFIG_SYS_EBC_CFG 0x7FC00000 /* EBC0_CFG */
/*-----------------------------------------------------------------------
* GPIO Setup
*----------------------------------------------------------------------*/
-#define CFG_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \
+#define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \
{ \
/* GPIO Core 0 */ \
{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO0 EBC_DATA_PAR(0) */ \
@@ -551,36 +551,36 @@
/*-----------------------------------------------------------------------
* Some Kilauea stuff..., mainly fpga registers
*/
-#define CFG_FPGA_REG_BASE CFG_FPGA_BASE
-#define CFG_FPGA_FIFO_BASE (in32(CFG_FPGA_BASE) | (1 << 10))
+#define CONFIG_SYS_FPGA_REG_BASE CONFIG_SYS_FPGA_BASE
+#define CONFIG_SYS_FPGA_FIFO_BASE (in32(CONFIG_SYS_FPGA_BASE) | (1 << 10))
/* interrupt */
-#define CFG_FPGA_SLIC0_R_DPRAM_INT 0x80000000
-#define CFG_FPGA_SLIC0_W_DPRAM_INT 0x40000000
-#define CFG_FPGA_SLIC1_R_DPRAM_INT 0x20000000
-#define CFG_FPGA_SLIC1_W_DPRAM_INT 0x10000000
-#define CFG_FPGA_PHY0_INT 0x08000000
-#define CFG_FPGA_PHY1_INT 0x04000000
-#define CFG_FPGA_SLIC0_INT 0x02000000
-#define CFG_FPGA_SLIC1_INT 0x01000000
+#define CONFIG_SYS_FPGA_SLIC0_R_DPRAM_INT 0x80000000
+#define CONFIG_SYS_FPGA_SLIC0_W_DPRAM_INT 0x40000000
+#define CONFIG_SYS_FPGA_SLIC1_R_DPRAM_INT 0x20000000
+#define CONFIG_SYS_FPGA_SLIC1_W_DPRAM_INT 0x10000000
+#define CONFIG_SYS_FPGA_PHY0_INT 0x08000000
+#define CONFIG_SYS_FPGA_PHY1_INT 0x04000000
+#define CONFIG_SYS_FPGA_SLIC0_INT 0x02000000
+#define CONFIG_SYS_FPGA_SLIC1_INT 0x01000000
/* DPRAM setting */
/* 00: 32B; 01: 64B; 10: 128B; 11: 256B */
-#define CFG_FPGA_DPRAM_R_INT_LINE 0x00400000 /* 64 B */
-#define CFG_FPGA_DPRAM_W_INT_LINE 0x00100000 /* 64 B */
-#define CFG_FPGA_DPRAM_RW_TYPE 0x00080000
-#define CFG_FPGA_DPRAM_RST 0x00040000
-#define CFG_FPGA_UART0_FO 0x00020000
-#define CFG_FPGA_UART1_FO 0x00010000
+#define CONFIG_SYS_FPGA_DPRAM_R_INT_LINE 0x00400000 /* 64 B */
+#define CONFIG_SYS_FPGA_DPRAM_W_INT_LINE 0x00100000 /* 64 B */
+#define CONFIG_SYS_FPGA_DPRAM_RW_TYPE 0x00080000
+#define CONFIG_SYS_FPGA_DPRAM_RST 0x00040000
+#define CONFIG_SYS_FPGA_UART0_FO 0x00020000
+#define CONFIG_SYS_FPGA_UART1_FO 0x00010000
/* loopback */
-#define CFG_FPGA_CHIPSIDE_LOOPBACK 0x00004000
-#define CFG_FPGA_LINESIDE_LOOPBACK 0x00008000
-#define CFG_FPGA_SLIC0_ENABLE 0x00002000
-#define CFG_FPGA_SLIC1_ENABLE 0x00001000
-#define CFG_FPGA_SLIC0_CS 0x00000800
-#define CFG_FPGA_SLIC1_CS 0x00000400
-#define CFG_FPGA_USER_LED0 0x00000200
-#define CFG_FPGA_USER_LED1 0x00000100
+#define CONFIG_SYS_FPGA_CHIPSIDE_LOOPBACK 0x00004000
+#define CONFIG_SYS_FPGA_LINESIDE_LOOPBACK 0x00008000
+#define CONFIG_SYS_FPGA_SLIC0_ENABLE 0x00002000
+#define CONFIG_SYS_FPGA_SLIC1_ENABLE 0x00001000
+#define CONFIG_SYS_FPGA_SLIC0_CS 0x00000800
+#define CONFIG_SYS_FPGA_SLIC1_CS 0x00000400
+#define CONFIG_SYS_FPGA_USER_LED0 0x00000200
+#define CONFIG_SYS_FPGA_USER_LED1 0x00000100
#endif /* __CONFIG_H */