rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
diff --git a/include/configs/lwmon.h b/include/configs/lwmon.h
index e4ee099..d52a5e0 100644
--- a/include/configs/lwmon.h
+++ b/include/configs/lwmon.h
@@ -73,18 +73,18 @@
#undef CONFIG_BOOTARGS
/* POST support */
-#define CONFIG_POST (CFG_POST_CACHE | \
- CFG_POST_WATCHDOG | \
- CFG_POST_RTC | \
- CFG_POST_MEMORY | \
- CFG_POST_CPU | \
- CFG_POST_UART | \
- CFG_POST_ETHER | \
- CFG_POST_I2C | \
- CFG_POST_SPI | \
- CFG_POST_USB | \
- CFG_POST_SPR | \
- CFG_POST_SYSMON)
+#define CONFIG_POST (CONFIG_SYS_POST_CACHE | \
+ CONFIG_SYS_POST_WATCHDOG | \
+ CONFIG_SYS_POST_RTC | \
+ CONFIG_SYS_POST_MEMORY | \
+ CONFIG_SYS_POST_CPU | \
+ CONFIG_SYS_POST_UART | \
+ CONFIG_SYS_POST_ETHER | \
+ CONFIG_SYS_POST_I2C | \
+ CONFIG_SYS_POST_SPI | \
+ CONFIG_SYS_POST_USB | \
+ CONFIG_SYS_POST_SPR | \
+ CONFIG_SYS_POST_SYSMON)
/*
* Keyboard commands:
@@ -135,10 +135,10 @@
"verify=no"
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
#define CONFIG_WATCHDOG 1 /* watchdog enabled */
-#define CFG_WATCHDOG_FREQ (CFG_HZ / 20)
+#define CONFIG_SYS_WATCHDOG_FREQ (CONFIG_SYS_HZ / 20)
#undef CONFIG_STATUS_LED /* Status LED disabled */
@@ -146,8 +146,8 @@
#undef CONFIG_HARD_I2C /* I2C with hardware support */
#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
-#define CFG_I2C_SPEED 93000 /* 93 kHz is supposed to work */
-#define CFG_I2C_SLAVE 0xFE
+#define CONFIG_SYS_I2C_SPEED 93000 /* 93 kHz is supposed to work */
+#define CONFIG_SYS_I2C_SLAVE 0xFE
#ifdef CONFIG_SOFT_I2C
/*
@@ -209,39 +209,39 @@
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
-#define CFG_HUSH_PARSER 1 /* use "hush" command parser */
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER 1 /* use "hush" command parser */
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#endif
#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
-#define CFG_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */
+#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */
-#define CFG_LOAD_ADDR 0x00100000 /* default load address */
+#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */
-#define CFG_PIO_MODE 0 /* IDE interface in PIO Mode 0 */
+#define CONFIG_SYS_PIO_MODE 0 /* IDE interface in PIO Mode 0 */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
/*
* When the watchdog is enabled, output must be fast enough in Linux.
*/
#ifdef CONFIG_WATCHDOG
-#define CFG_BAUDRATE_TABLE { 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 38400, 57600, 115200 }
#else
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
#endif
/*----------------------------------------------------------------------*/
@@ -266,53 +266,53 @@
/*-----------------------------------------------------------------------
* Internal Memory Mapped Register
*/
-#define CFG_IMMR 0xFFF00000
+#define CONFIG_SYS_IMMR 0xFFF00000
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
-#define CFG_INIT_RAM_ADDR CFG_IMMR
-#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 68 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
+#define CONFIG_SYS_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#define CONFIG_SYS_GBL_DATA_SIZE 68 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_FLASH_BASE 0x40000000
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_FLASH_BASE 0x40000000
#if defined(DEBUG) || defined(CONFIG_CMD_IDE)
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#else
-#define CFG_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */
+#define CONFIG_SYS_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */
#endif
-#define CFG_MONITOR_BASE CFG_FLASH_BASE
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
-#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
-#define CFG_FLASH_ERASE_TOUT 180000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 600 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_USE_BUFFER_WRITE
-#define CFG_FLASH_BUFFER_WRITE_TOUT 2048 /* Timeout for Flash Buffer Write (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 180000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 600 /* Timeout for Flash Write (in ms) */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#define CONFIG_SYS_FLASH_BUFFER_WRITE_TOUT 2048 /* Timeout for Flash Buffer Write (in ms) */
/* Buffer size.
We have two flash devices connected in parallel.
Each device incorporates a Write Buffer of 32 bytes.
*/
-#define CFG_FLASH_BUFFER_SIZE (2*32)
+#define CONFIG_SYS_FLASH_BUFFER_SIZE (2*32)
/* Put environment in flash which is much faster to boot than using the EEPROM */
#define CONFIG_ENV_IS_IN_FLASH 1
@@ -324,62 +324,62 @@
* I2C/EEPROM Configuration
*/
-#define CFG_I2C_AUDIO_ADDR 0x28 /* Audio volume control */
-#define CFG_I2C_SYSMON_ADDR 0x2E /* LM87 System Monitor */
-#define CFG_I2C_RTC_ADDR 0x51 /* PCF8563 RTC */
-#define CFG_I2C_POWER_A_ADDR 0x52 /* PCMCIA/USB power switch, channel A */
-#define CFG_I2C_POWER_B_ADDR 0x53 /* PCMCIA/USB power switch, channel B */
-#define CFG_I2C_KEYBD_ADDR 0x56 /* PIC LWE keyboard */
-#define CFG_I2C_PICIO_ADDR 0x57 /* PIC IO Expander */
+#define CONFIG_SYS_I2C_AUDIO_ADDR 0x28 /* Audio volume control */
+#define CONFIG_SYS_I2C_SYSMON_ADDR 0x2E /* LM87 System Monitor */
+#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* PCF8563 RTC */
+#define CONFIG_SYS_I2C_POWER_A_ADDR 0x52 /* PCMCIA/USB power switch, channel A */
+#define CONFIG_SYS_I2C_POWER_B_ADDR 0x53 /* PCMCIA/USB power switch, channel B */
+#define CONFIG_SYS_I2C_KEYBD_ADDR 0x56 /* PIC LWE keyboard */
+#define CONFIG_SYS_I2C_PICIO_ADDR 0x57 /* PIC IO Expander */
#undef CONFIG_USE_FRAM /* Use FRAM instead of EEPROM */
#ifdef CONFIG_USE_FRAM /* use FRAM */
-#define CFG_I2C_EEPROM_ADDR 0x55 /* FRAM FM24CL64 */
-#define CFG_I2C_EEPROM_ADDR_LEN 2
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x55 /* FRAM FM24CL64 */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
#else /* use EEPROM */
-#define CFG_I2C_EEPROM_ADDR 0x58 /* EEPROM AT24C164 */
-#define CFG_I2C_EEPROM_ADDR_LEN 1
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* takes up to 10 msec */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x58 /* EEPROM AT24C164 */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* takes up to 10 msec */
#endif /* CONFIG_USE_FRAM */
-#define CFG_EEPROM_PAGE_WRITE_BITS 4
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
/* List of I2C addresses to be verified by POST */
#ifdef CONFIG_USE_FRAM
-#define I2C_ADDR_LIST { /* CFG_I2C_AUDIO_ADDR, */ \
- CFG_I2C_SYSMON_ADDR, \
- CFG_I2C_RTC_ADDR, \
- CFG_I2C_POWER_A_ADDR, \
- CFG_I2C_POWER_B_ADDR, \
- CFG_I2C_KEYBD_ADDR, \
- CFG_I2C_PICIO_ADDR, \
- CFG_I2C_EEPROM_ADDR, \
+#define I2C_ADDR_LIST { /* CONFIG_SYS_I2C_AUDIO_ADDR, */ \
+ CONFIG_SYS_I2C_SYSMON_ADDR, \
+ CONFIG_SYS_I2C_RTC_ADDR, \
+ CONFIG_SYS_I2C_POWER_A_ADDR, \
+ CONFIG_SYS_I2C_POWER_B_ADDR, \
+ CONFIG_SYS_I2C_KEYBD_ADDR, \
+ CONFIG_SYS_I2C_PICIO_ADDR, \
+ CONFIG_SYS_I2C_EEPROM_ADDR, \
}
#else /* Use EEPROM - which show up on 8 consequtive addresses */
-#define I2C_ADDR_LIST { /* CFG_I2C_AUDIO_ADDR, */ \
- CFG_I2C_SYSMON_ADDR, \
- CFG_I2C_RTC_ADDR, \
- CFG_I2C_POWER_A_ADDR, \
- CFG_I2C_POWER_B_ADDR, \
- CFG_I2C_KEYBD_ADDR, \
- CFG_I2C_PICIO_ADDR, \
- CFG_I2C_EEPROM_ADDR+0, \
- CFG_I2C_EEPROM_ADDR+1, \
- CFG_I2C_EEPROM_ADDR+2, \
- CFG_I2C_EEPROM_ADDR+3, \
- CFG_I2C_EEPROM_ADDR+4, \
- CFG_I2C_EEPROM_ADDR+5, \
- CFG_I2C_EEPROM_ADDR+6, \
- CFG_I2C_EEPROM_ADDR+7, \
+#define I2C_ADDR_LIST { /* CONFIG_SYS_I2C_AUDIO_ADDR, */ \
+ CONFIG_SYS_I2C_SYSMON_ADDR, \
+ CONFIG_SYS_I2C_RTC_ADDR, \
+ CONFIG_SYS_I2C_POWER_A_ADDR, \
+ CONFIG_SYS_I2C_POWER_B_ADDR, \
+ CONFIG_SYS_I2C_KEYBD_ADDR, \
+ CONFIG_SYS_I2C_PICIO_ADDR, \
+ CONFIG_SYS_I2C_EEPROM_ADDR+0, \
+ CONFIG_SYS_I2C_EEPROM_ADDR+1, \
+ CONFIG_SYS_I2C_EEPROM_ADDR+2, \
+ CONFIG_SYS_I2C_EEPROM_ADDR+3, \
+ CONFIG_SYS_I2C_EEPROM_ADDR+4, \
+ CONFIG_SYS_I2C_EEPROM_ADDR+5, \
+ CONFIG_SYS_I2C_EEPROM_ADDR+6, \
+ CONFIG_SYS_I2C_EEPROM_ADDR+7, \
}
#endif /* CONFIG_USE_FRAM */
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
@@ -389,10 +389,10 @@
* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
*/
#if 0 && defined(CONFIG_WATCHDOG) /* LWMON uses external MAX706TESA WD */
-#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
#else
-#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
#endif
/*-----------------------------------------------------------------------
@@ -402,22 +402,22 @@
*/
/* EARB, DBGC and DBPC are initialised by the HCW */
/* => 0x000000C0 */
-#define CFG_SIUMCR (SIUMCR_GB5E)
-/*#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) */
+#define CONFIG_SYS_SIUMCR (SIUMCR_GB5E)
+/*#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) */
/*-----------------------------------------------------------------------
* TBSCR - Time Base Status and Control 11-26
*-----------------------------------------------------------------------
* Clear Reference Interrupt Status, Timebase freezing enabled
*/
-#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
/*-----------------------------------------------------------------------
* PISCR - Periodic Interrupt Status and Control 11-31
*-----------------------------------------------------------------------
* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
*/
-#define CFG_PISCR (PISCR_PS | PISCR_PITF)
+#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
/*-----------------------------------------------------------------------
* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
@@ -426,15 +426,15 @@
* interrupt status bit, set PLL multiplication factor !
*/
/* 0x00405000 */
-#define CFG_PLPRCR_MF 4 /* (4+1) * 13.2 = 66 MHz Clock */
-#define CFG_PLPRCR \
- ( (CFG_PLPRCR_MF << PLPRCR_MF_SHIFT) | \
+#define CONFIG_SYS_PLPRCR_MF 4 /* (4+1) * 13.2 = 66 MHz Clock */
+#define CONFIG_SYS_PLPRCR \
+ ( (CONFIG_SYS_PLPRCR_MF << PLPRCR_MF_SHIFT) | \
PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST | \
/*PLPRCR_CSRC|*/ PLPRCR_LPM_NORMAL | \
PLPRCR_CSR /*| PLPRCR_LOLRE|PLPRCR_FIOPD*/ \
)
-#define CONFIG_8xx_GCLK_FREQ ((CFG_PLPRCR_MF+1)*13200000)
+#define CONFIG_8xx_GCLK_FREQ ((CONFIG_SYS_PLPRCR_MF+1)*13200000)
/*-----------------------------------------------------------------------
* SCCR - System Clock and reset Control Register 15-27
@@ -444,7 +444,7 @@
*/
#define SCCR_MASK SCCR_EBDF11
/* 0x01800000 */
-#define CFG_SCCR (SCCR_COM00 | /*SCCR_TBS|*/ \
+#define CONFIG_SYS_SCCR (SCCR_COM00 | /*SCCR_TBS|*/ \
SCCR_RTDIV | SCCR_RTSEL | \
/*SCCR_CRQEN|*/ /*SCCR_PRQEN|*/ \
SCCR_EBDF00 | SCCR_DFSYNC00 | \
@@ -457,41 +457,41 @@
*-----------------------------------------------------------------------
*/
/* 0x00C3 => 0x0003 */
-#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
+#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
/*-----------------------------------------------------------------------
* RCCR - RISC Controller Configuration Register 19-4
*-----------------------------------------------------------------------
*/
-#define CFG_RCCR 0x0000
+#define CONFIG_SYS_RCCR 0x0000
/*-----------------------------------------------------------------------
* RMDS - RISC Microcode Development Support Control Register
*-----------------------------------------------------------------------
*/
-#define CFG_RMDS 0
+#define CONFIG_SYS_RMDS 0
/*-----------------------------------------------------------------------
*
* Interrupt Levels
*-----------------------------------------------------------------------
*/
-#define CFG_CPM_INTERRUPT 13 /* SIU_LEVEL6 */
+#define CONFIG_SYS_CPM_INTERRUPT 13 /* SIU_LEVEL6 */
/*-----------------------------------------------------------------------
* PCMCIA stuff
*-----------------------------------------------------------------------
*
*/
-#define CFG_PCMCIA_MEM_ADDR (0x50000000)
-#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_DMA_ADDR (0x54000000)
-#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_ATTRB_ADDR (0x58000000)
-#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_IO_ADDR (0x5C000000)
-#define CFG_PCMCIA_IO_SIZE ( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_MEM_ADDR (0x50000000)
+#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_DMA_ADDR (0x54000000)
+#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0x58000000)
+#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_IO_ADDR (0x5C000000)
+#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
/*-----------------------------------------------------------------------
* IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
@@ -504,21 +504,21 @@
#undef CONFIG_IDE_LED /* LED for ide not supported */
#undef CONFIG_IDE_RESET /* reset for ide not supported */
-#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
+#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-#define CFG_ATA_IDE0_OFFSET 0x0000
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR
+#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
/* Offset for data I/O */
-#define CFG_ATA_DATA_OFFSET (CFG_PCMCIA_MEM_SIZE + 0x320)
+#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
/* Offset for normal register accesses */
-#define CFG_ATA_REG_OFFSET (2 * CFG_PCMCIA_MEM_SIZE + 0x320)
+#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
/* Offset for alternate registers */
-#define CFG_ATA_ALT_OFFSET 0x0100
+#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
#define CONFIG_SUPPORT_VFAT /* enable VFAT support */
@@ -527,7 +527,7 @@
*-----------------------------------------------------------------------
*
*/
-#define CFG_DER 0
+#define CONFIG_SYS_DER 0
/*
* Init Memory Controller:
@@ -542,22 +542,22 @@
* restrict access enough to keep SRAM working (if any)
* but not too much to meddle with FLASH accesses
*/
-#define CFG_REMAP_OR_AM 0xFF000000 /* OR addr mask */
-#define CFG_PRELIM_OR_AM 0xFF000000 /* OR addr mask */
+#define CONFIG_SYS_REMAP_OR_AM 0xFF000000 /* OR addr mask */
+#define CONFIG_SYS_PRELIM_OR_AM 0xFF000000 /* OR addr mask */
/* FLASH timing: ACS = 00, TRLX = 0, CSNT = 1, SCY = 8, EHTR = 0 */
-#define CFG_OR_TIMING_FLASH (OR_SCY_8_CLK)
+#define CONFIG_SYS_OR_TIMING_FLASH (OR_SCY_8_CLK)
-#define CFG_OR0_REMAP ( CFG_REMAP_OR_AM | OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \
- CFG_OR_TIMING_FLASH)
-#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | OR_ACS_DIV1 | OR_BI | \
- CFG_OR_TIMING_FLASH)
+#define CONFIG_SYS_OR0_REMAP ( CONFIG_SYS_REMAP_OR_AM | OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \
+ CONFIG_SYS_OR_TIMING_FLASH)
+#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | OR_ACS_DIV1 | OR_BI | \
+ CONFIG_SYS_OR_TIMING_FLASH)
/* 16 bit, bank valid */
-#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_32 | BR_V )
+#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_32 | BR_V )
-#define CFG_OR1_REMAP CFG_OR0_REMAP
-#define CFG_OR1_PRELIM CFG_OR0_PRELIM
-#define CFG_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_PS_32 | BR_V )
+#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP
+#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
+#define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_PS_32 | BR_V )
/*
* BR3/OR3: SDRAM
@@ -570,8 +570,8 @@
#define SDRAM_MAX_SIZE 0x08000000 /* max 128 MB SDRAM */
-#define CFG_OR3_PRELIM (SDRAM_PRELIM_OR_AM | OR_CSNT_SAM | OR_G5LS | SDRAM_TIMING )
-#define CFG_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+#define CONFIG_SYS_OR3_PRELIM (SDRAM_PRELIM_OR_AM | OR_CSNT_SAM | OR_G5LS | SDRAM_TIMING )
+#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
/*
* BR5/OR5: Touch Panel
@@ -582,32 +582,32 @@
#define TOUCHPNL_OR_AM 0xFFFF8000
#define TOUCHPNL_TIMING OR_SCY_0_CLK
-#define CFG_OR5_PRELIM (TOUCHPNL_OR_AM | OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \
+#define CONFIG_SYS_OR5_PRELIM (TOUCHPNL_OR_AM | OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \
TOUCHPNL_TIMING )
-#define CFG_BR5_PRELIM ((TOUCHPNL_BASE & BR_BA_MSK) | BR_PS_32 | BR_V )
+#define CONFIG_SYS_BR5_PRELIM ((TOUCHPNL_BASE & BR_BA_MSK) | BR_PS_32 | BR_V )
-#define CFG_MEMORY_75
-#undef CFG_MEMORY_7E
-#undef CFG_MEMORY_8E
+#define CONFIG_SYS_MEMORY_75
+#undef CONFIG_SYS_MEMORY_7E
+#undef CONFIG_SYS_MEMORY_8E
/*
* Memory Periodic Timer Prescaler
*/
/* periodic timer for refresh */
-#define CFG_MPTPR 0x200
+#define CONFIG_SYS_MPTPR 0x200
/*
* MAMR settings for SDRAM
*/
-#define CFG_MAMR_8COL 0x80802114
-#define CFG_MAMR_9COL 0x80904114
+#define CONFIG_SYS_MAMR_8COL 0x80802114
+#define CONFIG_SYS_MAMR_9COL 0x80904114
/*
* MAR setting for SDRAM
*/
-#define CFG_MAR 0x00000088
+#define CONFIG_SYS_MAR 0x00000088
/*
* Internal Definitions