rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
diff --git a/include/configs/voiceblue.h b/include/configs/voiceblue.h
index 312f720..866b72d 100644
--- a/include/configs/voiceblue.h
+++ b/include/configs/voiceblue.h
@@ -54,28 +54,28 @@
#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
-#define CFG_LOAD_ADDR PHYS_SDRAM_1 + 0x400000 /* default load address */
+#define CONFIG_SYS_LOAD_ADDR PHYS_SDRAM_1 + 0x400000 /* default load address */
/*
* FLASH organization
*/
-#define CFG_FLASH_CFI /* Flash is CFI conformant */
+#define CONFIG_SYS_FLASH_CFI /* Flash is CFI conformant */
#define CONFIG_FLASH_CFI_DRIVER /* Use the common driver */
-#define CFG_MAX_FLASH_BANKS 1
-#define CFG_FLASH_BASE PHYS_FLASH_1
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
/* FIXME: Does not work on AMD flash */
-/* #define CFG_FLASH_USE_BUFFER_WRITE 1 */ /* use buffered writes (20x faster) */
-#define CFG_MAX_FLASH_SECT 512 /* max # of sectors on one chip */
+/* #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 */ /* use buffered writes (20x faster) */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max # of sectors on one chip */
-#define CFG_MONITOR_BASE PHYS_FLASH_1
-#define CFG_MONITOR_LEN (256 * 1024)
+#define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
/*
* Environment settings
*/
#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_ADDR (PHYS_FLASH_1 + CFG_MONITOR_LEN)
+#define CONFIG_ENV_ADDR (PHYS_FLASH_1 + CONFIG_SYS_MONITOR_LEN)
#define CONFIG_ENV_SIZE (8 * 1024)
#define CONFIG_ENV_SECT_SIZE (64 * 1024)
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
@@ -86,10 +86,10 @@
/*
* Size of malloc() pool and stack
*/
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-#define CFG_MALLOC_LEN (4 * 1024 * 1024)
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
#define CONFIG_STACKSIZE (1 * 1024 * 1024)
-#define PHYS_SDRAM_1_RESERVED (CFG_MONITOR_LEN + CFG_MALLOC_LEN + CONFIG_STACKSIZE)
+#define PHYS_SDRAM_1_RESERVED (CONFIG_SYS_MONITOR_LEN + CONFIG_SYS_MALLOC_LEN + CONFIG_STACKSIZE)
/*
* Hardware drivers
@@ -98,25 +98,25 @@
#define CONFIG_SMC91111_BASE 0x08000300
#define CONFIG_HARD_I2C
-#define CFG_I2C_SPEED 100000
-#define CFG_I2C_SLAVE 1
+#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_SYS_I2C_SLAVE 1
#define CONFIG_DRIVER_OMAP1510_I2C
#define CONFIG_RTC_DS1307
-#define CFG_I2C_RTC_ADDR 0x68
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
/*
* NS16550 Configuration
*/
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE (-4)
-#define CFG_NS16550_CLK (CONFIG_XTAL_FREQ) /* can be 12M/32Khz or 48Mhz */
-#define CFG_NS16550_COM1 OMAP1510_UART1_BASE /* uart1 */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK (CONFIG_XTAL_FREQ) /* can be 12M/32Khz or 48Mhz */
+#define CONFIG_SYS_NS16550_COM1 OMAP1510_UART1_BASE /* uart1 */
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 115200
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*
@@ -152,7 +152,7 @@
#define CONFIG_BOOTDELAY 3
#define CONFIG_ZERO_BOOTDELAY_CHECK /* allow to break in always */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/
-#define CFG_AUTOLOAD "n" /* No autoload */
+#define CONFIG_SYS_AUTOLOAD "n" /* No autoload */
#define CONFIG_BOOTCOMMAND "run nboot"
#define CONFIG_PREBOOT "run setup"
#define CONFIG_EXTRA_ENV_SETTINGS \
@@ -197,27 +197,27 @@
/*
* Miscellaneous configurable options
*/
-#define CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_AUTO_COMPLETE
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "# " /* Monitor Command Prompt */
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "# " /* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START PHYS_SDRAM_1
-#define CFG_MEMTEST_END PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE - PHYS_SDRAM_1_RESERVED
+#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1
+#define CONFIG_SYS_MEMTEST_END PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE - PHYS_SDRAM_1_RESERVED
-#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
+#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
/* The 1510 has 3 timers, they can be driven by the RefClk (12Mhz) or by DPLL1.
* This time is further subdivided by a local divisor.
*/
-#define CFG_TIMERBASE OMAP1510_TIMER1_BASE
-#define CFG_PVT 7 /* 2^(pvt+1), divide by 256 */
-#define CFG_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CFG_PVT))
+#define CONFIG_SYS_TIMERBASE OMAP1510_TIMER1_BASE
+#define CONFIG_SYS_PVT 7 /* 2^(pvt+1), divide by 256 */
+#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PVT))
#define OMAP5910_DPLL_DIV 1
#define OMAP5910_DPLL_MUL ((CONFIG_SYS_CLK_FREQ * \