Add support for AMCC 440SP, add support for AMCC Luan 440SP eval board.
Patch by John Otken, 23 Nov 2005
diff --git a/board/amcc/luan/epld.h b/board/amcc/luan/epld.h
new file mode 100644
index 0000000..05362e0
--- /dev/null
+++ b/board/amcc/luan/epld.h
@@ -0,0 +1,85 @@
+#define EPLD0_FSEL_FB2 0x80
+#define EPLD0_BOOT_SMALL_FLASH 0x40 /* 0 boot from large flash, 1 from small flash */
+#define EPLD0_RAW_CARD_BIT0 0x20 /* raw card EC level */
+#define EPLD0_RAW_CARD_BIT1 0x10
+#define EPLD0_RAW_CARD_BIT2 0x08
+#define EPLD0_EXT_ARB_SEL_N 0x04 /* 0 select on-board ext PCI-X, 1 internal arbiter */
+#define EPLD0_FLASH_ONBRD_N 0x02 /* 0 small flash/SRAM active, 1 block access */
+#define EPLD0_FLASH_SRAM_SEL_N 0x01 /* 0 SRAM at mem top, 1 small flash at mem top */
+
+#define EPLD1_CLK_CNTL0 0x80 /* FSEL-FB1 of MPC9772 */
+#define EPLD1_PCIX0_CNTL1 0x40 /* S*0 of 9531 */
+#define EPLD1_PCIX0_CNTL2 0x20 /* S*1 of 9531 */
+#define EPLD1_CLK_CNTL3 0x10 /* FSEL-B1 of MPC9772 */
+#define EPLD1_CLK_CNTL4 0x08 /* FSEL-B0 of MPC9772 */
+#define EPLD1_MASTER_CLOCK6 0x04 /* clock source select 6 */
+#define EPLD1_MASTER_CLOCK7 0x02 /* clock source select 7 */
+#define EPLD1_MASTER_CLOCK8 0x01 /* clock source select 8 */
+
+#define EPLD2_ETH_MODE_10 0x80 /* Ethernet mode 10 (default = 1) */
+#define EPLD2_ETH_MODE_100 0x40 /* Ethernet mode 100 (default = 1) */
+#define EPLD2_ETH_MODE_1000 0x20 /* Ethernet mode 1000 (default = 1) */
+#define EPLD2_ETH_DUPLEX_MODE 0x10 /* Ethernet force full duplex mode */
+#define EPLD2_RESET_ETH_N 0x08 /* Ethernet reset (default = 1) */
+#define EPLD2_ETH_AUTO_NEGO 0x04 /* Ethernet auto negotiation */
+#define EPLD2_DEFAULT_UART_N 0x01 /* 0 select DSR DTR for UART1 */
+
+#define EPLD3_STATUS_LED4 0x08 /* status LED 8 (1 = LED on) */
+#define EPLD3_STATUS_LED3 0x04 /* status LED 4 (1 = LED on) */
+#define EPLD3_STATUS_LED2 0x02 /* status LED 2 (1 = LED on) */
+#define EPLD3_STATUS_LED1 0x01 /* status LED 1 (1 = LED on) */
+
+#define EPLD4_PCIX0_VTH1 0x80 /* PCI-X 0 VTH1 status */
+#define EPLD4_PCIX0_VTH2 0x40 /* PCI-X 0 VTH2 status */
+#define EPLD4_PCIX0_VTH3 0x20 /* PCI-X 0 VTH3 status */
+#define EPLD4_PCIX0_VTH4 0x10 /* PCI-X 0 VTH4 status */
+#define EPLD4_PCIX1_VTH1 0x08 /* PCI-X 1 VTH1 status */
+#define EPLD4_PCIX1_VTH2 0x04 /* PCI-X 1 VTH2 status */
+#define EPLD4_PCIX1_VTH3 0x02 /* PCI-X 1 VTH3 status */
+#define EPLD4_PCIX1_VTH4 0x01 /* PCI-X 1 VTH4 status */
+
+#define EPLD5_PCIX0_INT0 0x80 /* PCIX0 INT0 status, write 0 to reset */
+#define EPLD5_PCIX0_INT1 0x40 /* PCIX0 INT1 status, write 0 to reset */
+#define EPLD5_PCIX0_INT2 0x20 /* PCIX0 INT2 status, write 0 to reset */
+#define EPLD5_PCIX0_INT3 0x10 /* PCIX0 INT3 status, write 0 to reset */
+#define EPLD5_PCIX1_INT0 0x08 /* PCIX1 INT0 status, write 0 to reset */
+#define EPLD5_PCIX1_INT1 0x04 /* PCIX1 INT1 status, write 0 to reset */
+#define EPLD5_PCIX1_INT2 0x02 /* PCIX1 INT2 status, write 0 to reset */
+#define EPLD5_PCIX1_INT3 0x01 /* PCIX1 INT3 status, write 0 to reset */
+
+#define EPLD6_PCIX0_RESET_CTL 0x80 /* 0=enable slot reset, 1=disable slot reset */
+#define EPLD6_PCIX1_RESET_CTL 0x40 /* 0=enable slot reset, 1=disable slot reset */
+#define EPLD6_ETH_INT_MODE 0x20 /* 0=IRQ5 recv's external eth int */
+#define EPLD6_PCIX2_RESET_CTL 0x10 /* 0=enable slot reset, 1=disable slot reset */
+#define EPLD6_PCI1_CLKCNTL1 0x80 /* PCI1 clock control S*0 of 9531 */
+#define EPLD6_PCI1_CLKCNTL2 0x40 /* PCI1 clock control S*1 of 9531 */
+#define EPLD6_PCI2_CLKCNTL1 0x20 /* PCI2 clock control S*0 of 9531 */
+#define EPLD6_PCI2_CLKCNTL2 0x10 /* PCI2 clock control S*1 of 9531 */
+
+#define EPLD7_VTH1 0x80 /* PCI2 VTH1 status */
+#define EPLD7_VTH2 0x40 /* PCI2 VTH2 status */
+#define EPLD7_VTH3 0x20 /* PCI2 VTH3 status */
+#define EPLD7_VTH4 0x10 /* PCI2 VTH4 status */
+#define EPLD7_INTA_MODE 0x80 /* see S5 on SW2 for details */
+#define EPLD7_PCI_INT_MODE_N 0x40 /* see S1 on SW2 for details */
+#define EPLD7_WRITE_ENABLE_GPIO 0x20 /* see S2 on SW2 for details */
+#define EPLD7_WRITE_ENABLE_INT 0x10 /* see S3 on SW2 for details */
+
+
+typedef struct {
+ unsigned char status; /* misc status */
+ unsigned char clock; /* clock status, PCI-X clock control */
+ unsigned char ethuart; /* Ethernet, UART status */
+ unsigned char leds; /* LED register */
+ unsigned char vth01; /* PCI0, PCI1 VTH register */
+ unsigned char pciints; /* PCI0, PCI1 interrupts */
+ unsigned char pci2; /* PCI2 interrupts, clock control */
+ unsigned char vth2; /* PCI2 VTH register */
+ unsigned char filler1[4096-8];
+ unsigned char gpio00; /* GPIO bits 0-7 */
+ unsigned char gpio08; /* GPIO bits 8-15 */
+ unsigned char gpio16; /* GPIO bits 16-23 */
+ unsigned char gpio24; /* GPIO bits 24-31 */
+ unsigned char filler2[4096-4];
+ unsigned char version; /* EPLD version */
+} epld_t;