ARM: dts: sunxi: A13/A31/A23/A33: Sync from Linux v5.18-rc1
Copy the devicetree source for the A10s/A13/GR8, A31(s), and A23/A33/R16
SoCs and all existing boards from the Linux v5.18-rc1 tag.
These changes are combined into one commit due to interdependencies:
- The unit addresses were removed from bitbanged I2C buses, which
drives a Kconfig default change. This affects sun5i-a13-utoo-p66.dts
and sun6i-a31-colombus.dts.
- The pinctrl nodes were renamed, including some used by the shared
header sunxi-reference-design-tablet.dtsi.
To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 994e5818392c and 9fdef3c3d8c2.
This commit renames the file sun8i-r16-nintendo-nes-classic-edition.dts
to sun8i-r16-nintendo-nes-classic.dts to match the Linux tree.
This commit also adds the following new board devicetrees:
- sun5i-a13-licheepi-one.dts
- sun5i-a13-pocketbook-touch-lux-3.dts
- sun5i-gr8-evb.dts
- sun8i-a23-ippo-q8h-v1.2.dts
- sun8i-a23-ippo-q8h-v5.dts
- sun8i-a33-et-q8-v1.6.dts
- sun8i-a33-ippo-q8h-v1.2.dts
- sun8i-r16-nintendo-super-nes-classic.dts
As with the other SoCs, updates of note are conversion of GPIO pull-up
from pinconf to GPIO flags and renaming the detection GPIO properties in
the USB PHY nodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
diff --git a/arch/arm/dts/sun5i-a10s-wobo-i5.dts b/arch/arm/dts/sun5i-a10s-wobo-i5.dts
index 3f68ef5..ef8baa9 100644
--- a/arch/arm/dts/sun5i-a10s-wobo-i5.dts
+++ b/arch/arm/dts/sun5i-a10s-wobo-i5.dts
@@ -61,10 +61,8 @@
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_wobo_i5>;
- blue {
+ led {
label = "a10s-wobo-i5:blue:usr";
gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>;
default-state = "on";
@@ -73,8 +71,6 @@
reg_emac_3v3: emac-3v3 {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&emac_power_pin_wobo>;
regulator-name = "emac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
@@ -94,8 +90,8 @@
&emac {
pinctrl-names = "default";
- pinctrl-0 = <&emac_pins_a>;
- phy = <&phy1>;
+ pinctrl-0 = <&emac_pd_pins>;
+ phy-handle = <&phy1>;
status = "okay";
};
@@ -104,8 +100,6 @@
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
@@ -126,8 +120,6 @@
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_wobo_i5>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 1 3 GPIO_ACTIVE_LOW>; /* PB3 */
@@ -142,24 +134,6 @@
status = "okay";
};
-&pio {
- led_pins_wobo_i5: led_pins@0 {
- pins = "PB2";
- function = "gpio_out";
- };
-
- mmc0_cd_pin_wobo_i5: mmc0_cd_pin@0 {
- pins = "PB3";
- function = "gpio_in";
- bias-pull-up;
- };
-
- emac_power_pin_wobo: emac_power_pin@0 {
- pins = "PA02";
- function = "gpio_out";
- };
-};
-
®_dcdc2 {
regulator-always-on;
regulator-min-microvolt = <1000000>;
@@ -206,7 +180,7 @@
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};