ARM: dts: sunxi: A13/A31/A23/A33: Sync from Linux v5.18-rc1

Copy the devicetree source for the A10s/A13/GR8, A31(s), and A23/A33/R16
SoCs and all existing boards from the Linux v5.18-rc1 tag.

These changes are combined into one commit due to interdependencies:
 - The unit addresses were removed from bitbanged I2C buses, which
   drives a Kconfig default change. This affects sun5i-a13-utoo-p66.dts
   and sun6i-a31-colombus.dts.
 - The pinctrl nodes were renamed, including some used by the shared
   header sunxi-reference-design-tablet.dtsi.

To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 994e5818392c and 9fdef3c3d8c2.

This commit renames the file sun8i-r16-nintendo-nes-classic-edition.dts
to sun8i-r16-nintendo-nes-classic.dts to match the Linux tree.

This commit also adds the following new board devicetrees:
 - sun5i-a13-licheepi-one.dts
 - sun5i-a13-pocketbook-touch-lux-3.dts
 - sun5i-gr8-evb.dts
 - sun8i-a23-ippo-q8h-v1.2.dts
 - sun8i-a23-ippo-q8h-v5.dts
 - sun8i-a33-et-q8-v1.6.dts
 - sun8i-a33-ippo-q8h-v1.2.dts
 - sun8i-r16-nintendo-super-nes-classic.dts

As with the other SoCs, updates of note are conversion of GPIO pull-up
from pinconf to GPIO flags and renaming the detection GPIO properties in
the USB PHY nodes.

Signed-off-by: Samuel Holland <samuel@sholland.org>
diff --git a/arch/arm/dts/sun5i-a13-pocketbook-touch-lux-3.dts b/arch/arm/dts/sun5i-a13-pocketbook-touch-lux-3.dts
new file mode 100644
index 0000000..d604077
--- /dev/null
+++ b/arch/arm/dts/sun5i-a13-pocketbook-touch-lux-3.dts
@@ -0,0 +1,258 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright 2019 Ondrej Jirman <megous@megous.com>
+ */
+
+/dts-v1/;
+#include "sun5i-a13.dtsi"
+#include "sunxi-common-regulators.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	model = "PocketBook Touch Lux 3";
+	compatible = "pocketbook,touch-lux-3", "allwinner,sun5i-a13";
+
+	aliases {
+		serial0 = &uart1;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+		enable-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
+		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+		default-brightness-level = <8>;
+		power-supply = <&reg_vcc3v3>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led {
+			gpios = <&pio 4 8 GPIO_ACTIVE_LOW>; /* PE8 */
+			default-state = "on";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+		label = "GPIO Keys";
+
+		key-right {
+			label = "Right";
+			linux,code = <KEY_RIGHT>;
+			gpios = <&pio 6 9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PG9 */
+		};
+
+		key-left {
+			label = "Left";
+			linux,code = <KEY_LEFT>;
+			gpios = <&pio 6 10 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PG10 */
+		};
+	};
+
+	reg_1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-1v8-nor-ctp";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&pio 2 15 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_1v8_nor: regulator-nor {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-nor";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&pio 2 14 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&reg_1v8>;
+		regulator-always-on;
+	};
+
+	reg_1v8_ctp: regulator-ctp {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-ctp";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&pio 2 13 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&reg_1v8>;
+	};
+
+	reg_3v3_mmc0: regulator-mmc0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-mmc0";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&pio 4 4 GPIO_ACTIVE_LOW>; /* PE4 */
+		vin-supply = <&reg_vcc3v3>;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	axp209: pmic@34 {
+		reg = <0x34>;
+		interrupts = <0>;
+	};
+};
+
+#include "axp209.dtsi"
+
+&i2c1 {
+	status = "okay";
+
+	pcf8563: rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	/* Touchpanel is connected here. */
+};
+
+&lradc {
+	vref-supply = <&reg_ldo2>;
+	status = "okay";
+
+	button-200 {
+		label = "Home";
+		linux,code = <KEY_HOME>;
+		channel = <0>;
+		voltage = <200000>;
+	};
+
+	button-400 {
+		label = "Menu";
+		linux,code = <KEY_MENU>;
+		channel = <0>;
+		voltage = <400000>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_3v3_mmc0>;
+	bus-width = <4>;
+	cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
+	status = "okay";
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_4bit_pc_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&otg_sram {
+	status = "okay";
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_pin>;
+	status = "okay";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vdd-int-pll";
+};
+
+&reg_ldo1 {
+	regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
+
+&reg_ldo3 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+	/* We need this otherwise the LDO3 would overload */
+	regulator-soft-start;
+	regulator-ramp-delay = <1600>;
+};
+
+&spi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pe_pins>, <&spi2_cs0_pe_pin>;
+	status = "okay";
+
+	epd_flash: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "macronix,mx25u4033", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <4000000>;
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pg_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&battery_power_supply {
+	status = "okay";
+};
+
+&usb_power_supply {
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_ldo3>;
+	status = "okay";
+};