ARM: dts: sunxi: A13/A31/A23/A33: Sync from Linux v5.18-rc1
Copy the devicetree source for the A10s/A13/GR8, A31(s), and A23/A33/R16
SoCs and all existing boards from the Linux v5.18-rc1 tag.
These changes are combined into one commit due to interdependencies:
- The unit addresses were removed from bitbanged I2C buses, which
drives a Kconfig default change. This affects sun5i-a13-utoo-p66.dts
and sun6i-a31-colombus.dts.
- The pinctrl nodes were renamed, including some used by the shared
header sunxi-reference-design-tablet.dtsi.
To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 994e5818392c and 9fdef3c3d8c2.
This commit renames the file sun8i-r16-nintendo-nes-classic-edition.dts
to sun8i-r16-nintendo-nes-classic.dts to match the Linux tree.
This commit also adds the following new board devicetrees:
- sun5i-a13-licheepi-one.dts
- sun5i-a13-pocketbook-touch-lux-3.dts
- sun5i-gr8-evb.dts
- sun8i-a23-ippo-q8h-v1.2.dts
- sun8i-a23-ippo-q8h-v5.dts
- sun8i-a33-et-q8-v1.6.dts
- sun8i-a33-ippo-q8h-v1.2.dts
- sun8i-r16-nintendo-super-nes-classic.dts
As with the other SoCs, updates of note are conversion of GPIO pull-up
from pinconf to GPIO flags and renaming the detection GPIO properties in
the USB PHY nodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
diff --git a/arch/arm/dts/sun6i-reference-design-tablet.dtsi b/arch/arm/dts/sun6i-reference-design-tablet.dtsi
index 4e72e4f..6bf3fbd 100644
--- a/arch/arm/dts/sun6i-reference-design-tablet.dtsi
+++ b/arch/arm/dts/sun6i-reference-design-tablet.dtsi
@@ -66,34 +66,20 @@
&mmc0 {
pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_e708_q1>;
+ pinctrl-0 = <&mmc0_pins>;
vmmc-supply = <®_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */
status = "okay";
};
-&pio {
- mmc0_cd_pin_e708_q1: mmc0_cd_pin@0 {
- pins = "PA8";
- function = "gpio_in";
- bias-pull-up;
- };
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- pins = "PA15";
- function = "gpio_in";
- bias-pull-up;
- };
-};
-
&p2wi {
status = "okay";
axp22x: pmic@68 {
compatible = "x-powers,axp221";
reg = <0x68>;
- interrupt-parent = <&nmi_intc>;
+ interrupt-parent = <&r_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
drivevbus-supply = <®_vcc5v0>;
x-powers,drive-vbus-en;
@@ -179,9 +165,7 @@
};
&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>;
- usb0_id_det-gpio = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */
+ usb0_id_det-gpios = <&pio 0 15 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PA15 */
usb0_vbus_power-supply = <&usb_power_supply>;
usb0_vbus-supply = <®_drivevbus>;
usb1_vbus-supply = <®_dldo1>;