ehci-mxc: Add support for i.MX35
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
diff --git a/drivers/usb/host/ehci-mxc.c b/drivers/usb/host/ehci-mxc.c
index 6260a8c..7c5f71c 100644
--- a/drivers/usb/host/ehci-mxc.c
+++ b/drivers/usb/host/ehci-mxc.c
@@ -58,6 +58,22 @@
#define MX31_H1_PM_BIT (1 << 8)
#define MX31_H1_DT_BIT (1 << 4)
+#define MX35_OTG_SIC_SHIFT 29
+#define MX35_OTG_SIC_MASK (0x3 << MX35_OTG_SIC_SHIFT)
+#define MX35_OTG_PM_BIT (1 << 24)
+#define MX35_OTG_PP_BIT (1 << 11)
+#define MX35_OTG_OCPOL_BIT (1 << 3)
+
+#define MX35_H1_SIC_SHIFT 21
+#define MX35_H1_SIC_MASK (0x3 << MX35_H1_SIC_SHIFT)
+#define MX35_H1_PP_BIT (1 << 18)
+#define MX35_H1_PM_BIT (1 << 8)
+#define MX35_H1_IPPUE_UP_BIT (1 << 7)
+#define MX35_H1_IPPUE_DOWN_BIT (1 << 6)
+#define MX35_H1_TLL_BIT (1 << 5)
+#define MX35_H1_USBTE_BIT (1 << 4)
+#define MX35_H1_OCPOL_BIT (1 << 2)
+
static int mxc_set_usbcontrol(int port, unsigned int flags)
{
unsigned int v;
@@ -147,6 +163,55 @@
default:
return -EINVAL;
}
+#elif defined(CONFIG_MX35)
+ switch (port) {
+ case 0: /* OTG port */
+ v &= ~(MX35_OTG_SIC_MASK | MX35_OTG_PM_BIT | MX35_OTG_PP_BIT |
+ MX35_OTG_OCPOL_BIT);
+ v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX35_OTG_SIC_SHIFT;
+
+ if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
+ v |= MX35_OTG_PM_BIT;
+
+ if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
+ v |= MX35_OTG_PP_BIT;
+
+ if (!(flags & MXC_EHCI_OC_PIN_ACTIVE_LOW))
+ v |= MX35_OTG_OCPOL_BIT;
+
+ break;
+ case 1: /* H1 port */
+ v &= ~(MX35_H1_SIC_MASK | MX35_H1_PM_BIT | MX35_H1_PP_BIT |
+ MX35_H1_OCPOL_BIT | MX35_H1_TLL_BIT |
+ MX35_H1_USBTE_BIT | MX35_H1_IPPUE_DOWN_BIT |
+ MX35_H1_IPPUE_UP_BIT);
+ v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX35_H1_SIC_SHIFT;
+
+ if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
+ v |= MX35_H1_PM_BIT;
+
+ if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
+ v |= MX35_H1_PP_BIT;
+
+ if (!(flags & MXC_EHCI_OC_PIN_ACTIVE_LOW))
+ v |= MX35_H1_OCPOL_BIT;
+
+ if (!(flags & MXC_EHCI_TTL_ENABLED))
+ v |= MX35_H1_TLL_BIT;
+
+ if (flags & MXC_EHCI_INTERNAL_PHY)
+ v |= MX35_H1_USBTE_BIT;
+
+ if (flags & MXC_EHCI_IPPUE_DOWN)
+ v |= MX35_H1_IPPUE_DOWN_BIT;
+
+ if (flags & MXC_EHCI_IPPUE_UP)
+ v |= MX35_H1_IPPUE_UP_BIT;
+
+ break;
+ default:
+ return -EINVAL;
+ }
#else
#error MXC EHCI USB driver not supported on this platform
#endif
@@ -176,6 +241,10 @@
setbits_le32(&ehci->usbmode, CM_HOST);
__raw_writel(CONFIG_MXC_USB_PORTSC, &ehci->portsc);
mxc_set_usbcontrol(CONFIG_MXC_USB_PORT, CONFIG_MXC_USB_FLAGS);
+#ifdef CONFIG_MX35
+ /* Workaround for ENGcm11601 */
+ __raw_writel(0, &ehci->sbuscfg);
+#endif
udelay(10000);