ARM: dts: rmobile: Synchronize DTs with Linux 6.1.7
Synchronize R-Car device trees with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
The following script has been used for the synchronization:
$ for i in $(cd arch/arm/dts/ ; ls -1 r8a* | grep -v 'u-boot.dts' ; sed -n '/#include/ s@.*"\(.*\)"@\1@p' $(ls -1 r8a* | grep -v 'u-boot.dts')) ; do
if [ -e /linux-2.6/arch/arm64/boot/dts/renesas/$i ] ; then
cp /linux-2.6/arch/arm64/boot/dts/renesas/$i arch/arm/dts/ ;
elif [ -e /linux-2.6/arch/arm/boot/dts/$i ] ; then
cp /linux-2.6/arch/arm/boot/dts/$i arch/arm/dts/
else
echo "NOT FOUND: $i"
fi
done
$ git add $( ( cd arch/arm/dts/ ; ls -1 r8a* | grep -v 'u-boot.dts' ; sed -n '/#include/ s@.*"\(.*\)"@\1@p' $(ls -1 r8a* | grep -v 'u-boot.dts')) | tr " " "\n" | sed 's@^@arch/arm/dts/@g' )
Move the include/dt-bindings/{clk,clock}/versaclock.h header used by
the renesas boards to match Linux 6.1.y as well.
Keep arch/arm/dts/r8a774c0-u-boot.dtsi sdhi3 node as it is now used
by the arch/arm/dts/r8a774c0-cat874.dts board.
Pick s@spi-flash@flash@ change in arch/arm/dts/r8a779a0-falcon-u-boot.dts
from "ARM: dts: Synchronize R-Car V3U DTs with Linux 5.18.3" .
Adjust R8A77990 Ebisu CONFIG_SYS_MMC_ENV_DEV from 2 to 0 to reflect
the card enumeration in ebisu.dtsi /aliases DT node .
Adjust R8A7795 and R8A7796 ULCB CONFIG_SYS_MMC_ENV_DEV from 1 to 0 to
reflect the card enumeration in ulcb.dtsi /aliases DT node .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com> # r8a779a0-falcon-u-boot.dts
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> # r8a779a0-falcon-u-boot.dts
diff --git a/arch/arm/dts/r8a77995-draak.dts b/arch/arm/dts/r8a77995-draak.dts
index 67634cb..3848256 100644
--- a/arch/arm/dts/r8a77995-draak.dts
+++ b/arch/arm/dts/r8a77995-draak.dts
@@ -1,6 +1,6 @@
// SPDX-License-Identifier: GPL-2.0
/*
- * Device Tree Source for the Draak board
+ * Device Tree Source for the Draak board with R-Car D3
*
* Copyright (C) 2016-2018 Renesas Electronics Corp.
* Copyright (C) 2017 Glider bvba
@@ -8,521 +8,9 @@
/dts-v1/;
#include "r8a77995.dtsi"
-#include <dt-bindings/gpio/gpio.h>
+#include "draak.dtsi"
/ {
model = "Renesas Draak board based on r8a77995";
compatible = "renesas,draak", "renesas,r8a77995";
-
- aliases {
- serial0 = &scif2;
- ethernet0 = &avb;
- };
-
- backlight: backlight {
- compatible = "pwm-backlight";
- pwms = <&pwm1 0 50000>;
-
- brightness-levels = <512 511 505 494 473 440 392 327 241 133 0>;
- default-brightness-level = <10>;
-
- power-supply = <®_12p0v>;
- enable-gpios = <&gpio4 0 GPIO_ACTIVE_HIGH>;
- };
-
- chosen {
- bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
- stdout-path = "serial0:115200n8";
- };
-
- composite-in {
- compatible = "composite-video-connector";
-
- port {
- composite_con_in: endpoint {
- remote-endpoint = <&adv7180_in>;
- };
- };
- };
-
- hdmi-in {
- compatible = "hdmi-connector";
- type = "a";
-
- port {
- hdmi_con_in: endpoint {
- remote-endpoint = <&adv7612_in>;
- };
- };
- };
-
- hdmi-out {
- compatible = "hdmi-connector";
- type = "a";
-
- port {
- hdmi_con_out: endpoint {
- remote-endpoint = <&adv7511_out>;
- };
- };
- };
-
- lvds-decoder {
- compatible = "thine,thc63lvd1024";
- vcc-supply = <®_3p3v>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- thc63lvd1024_in: endpoint {
- remote-endpoint = <&lvds0_out>;
- };
- };
-
- port@2 {
- reg = <2>;
- thc63lvd1024_out: endpoint {
- remote-endpoint = <&adv7511_in>;
- };
- };
- };
- };
-
- memory@48000000 {
- device_type = "memory";
- /* first 128MB is reserved for secure area. */
- reg = <0x0 0x48000000 0x0 0x18000000>;
- };
-
- reg_1p8v: regulator-1p8v {
- compatible = "regulator-fixed";
- regulator-name = "fixed-1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- reg_3p3v: regulator-3p3v {
- compatible = "regulator-fixed";
- regulator-name = "fixed-3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- reg_12p0v: regulator-12p0v {
- compatible = "regulator-fixed";
- regulator-name = "D12.0V";
- regulator-min-microvolt = <12000000>;
- regulator-max-microvolt = <12000000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- vga {
- compatible = "vga-connector";
-
- port {
- vga_in: endpoint {
- remote-endpoint = <&adv7123_out>;
- };
- };
- };
-
- vga-encoder {
- compatible = "adi,adv7123";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- adv7123_in: endpoint {
- remote-endpoint = <&du_out_rgb>;
- };
- };
- port@1 {
- reg = <1>;
- adv7123_out: endpoint {
- remote-endpoint = <&vga_in>;
- };
- };
- };
- };
-
- x12_clk: x12 {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <74250000>;
- };
-};
-
-&avb {
- pinctrl-0 = <&avb0_pins>;
- pinctrl-names = "default";
- renesas,no-ether-link;
- phy-handle = <&phy0>;
- status = "okay";
-
- phy0: ethernet-phy@0 {
- rxc-skew-ps = <1500>;
- reg = <0>;
- interrupt-parent = <&gpio5>;
- interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
- /*
- * TX clock internal delay mode is required for reliable
- * 1Gbps communication using the KSZ9031RNX phy present on
- * the Draak board, however, TX clock internal delay mode
- * isn't supported on r8a77995. Thus, limit speed to
- * 100Mbps for reliable communication.
- */
- max-speed = <100>;
- };
-};
-
-&can0 {
- pinctrl-0 = <&can0_pins>;
- pinctrl-names = "default";
- status = "okay";
-};
-
-&can1 {
- pinctrl-0 = <&can1_pins>;
- pinctrl-names = "default";
- status = "okay";
-};
-
-&du {
- pinctrl-0 = <&du_pins>;
- pinctrl-names = "default";
- status = "okay";
-
- clocks = <&cpg CPG_MOD 724>,
- <&cpg CPG_MOD 723>,
- <&x12_clk>;
- clock-names = "du.0", "du.1", "dclkin.0";
-
- ports {
- port@0 {
- endpoint {
- remote-endpoint = <&adv7123_in>;
- };
- };
- };
-};
-
-&ehci0 {
- dr_mode = "host";
- status = "okay";
-};
-
-&extal_clk {
- clock-frequency = <48000000>;
-};
-
-&hsusb {
- dr_mode = "host";
- status = "okay";
-};
-
-&i2c0 {
- pinctrl-0 = <&i2c0_pins>;
- pinctrl-names = "default";
- status = "okay";
-
- composite-in@20 {
- compatible = "adi,adv7180cp";
- reg = <0x20>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- adv7180_in: endpoint {
- remote-endpoint = <&composite_con_in>;
- };
- };
-
- port@3 {
- reg = <3>;
-
- /*
- * The VIN4 video input path is shared between
- * CVBS and HDMI inputs through SW[49-53]
- * switches.
- *
- * CVBS is the default selection, link it to
- * VIN4 here.
- */
- adv7180_out: endpoint {
- remote-endpoint = <&vin4_in>;
- };
- };
- };
-
- };
-
- hdmi-encoder@39 {
- compatible = "adi,adv7511w";
- reg = <0x39>, <0x3f>, <0x38>, <0x3c>;
- reg-names = "main", "edid", "packet", "cec";
- interrupt-parent = <&gpio1>;
- interrupts = <28 IRQ_TYPE_LEVEL_LOW>;
-
- /* Depends on LVDS */
- max-clock = <135000000>;
- min-vrefresh = <50>;
-
- adi,input-depth = <8>;
- adi,input-colorspace = "rgb";
- adi,input-clock = "1x";
- adi,input-style = <1>;
- adi,input-justification = "evenly";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- adv7511_in: endpoint {
- remote-endpoint = <&thc63lvd1024_out>;
- };
- };
-
- port@1 {
- reg = <1>;
- adv7511_out: endpoint {
- remote-endpoint = <&hdmi_con_out>;
- };
- };
- };
- };
-
- hdmi-decoder@4c {
- compatible = "adi,adv7612";
- reg = <0x4c>;
- default-input = <0>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
-
- adv7612_in: endpoint {
- remote-endpoint = <&hdmi_con_in>;
- };
- };
-
- port@2 {
- reg = <2>;
-
- /*
- * The VIN4 video input path is shared between
- * CVBS and HDMI inputs through SW[49-53]
- * switches.
- *
- * CVBS is the default selection, leave HDMI
- * not connected here.
- */
- adv7612_out: endpoint {
- pclk-sample = <0>;
- hsync-active = <0>;
- vsync-active = <0>;
- };
- };
- };
- };
-
- eeprom@50 {
- compatible = "rohm,br24t01", "atmel,24c01";
- reg = <0x50>;
- pagesize = <8>;
- };
-};
-
-&i2c1 {
- pinctrl-0 = <&i2c1_pins>;
- pinctrl-names = "default";
- status = "okay";
-};
-
-&lvds0 {
- status = "okay";
-
- clocks = <&cpg CPG_MOD 727>,
- <&x12_clk>,
- <&extal_clk>;
- clock-names = "fck", "dclkin.0", "extal";
-
- ports {
- port@1 {
- lvds0_out: endpoint {
- remote-endpoint = <&thc63lvd1024_in>;
- };
- };
- };
-};
-
-&lvds1 {
- /*
- * Even though the LVDS1 output is not connected, the encoder must be
- * enabled to supply a pixel clock to the DU for the DPAD output when
- * LVDS0 is in use.
- */
- status = "okay";
-
- clocks = <&cpg CPG_MOD 727>,
- <&x12_clk>,
- <&extal_clk>;
- clock-names = "fck", "dclkin.0", "extal";
-};
-
-&ohci0 {
- dr_mode = "host";
- status = "okay";
-};
-
-&pfc {
- avb0_pins: avb {
- mux {
- groups = "avb0_link", "avb0_mdio", "avb0_mii";
- function = "avb0";
- };
- };
-
- can0_pins: can0 {
- groups = "can0_data_a";
- function = "can0";
- };
-
- can1_pins: can1 {
- groups = "can1_data_a";
- function = "can1";
- };
-
- du_pins: du {
- groups = "du_rgb888", "du_sync", "du_disp", "du_clk_out_0";
- function = "du";
- };
-
- i2c0_pins: i2c0 {
- groups = "i2c0";
- function = "i2c0";
- };
-
- i2c1_pins: i2c1 {
- groups = "i2c1";
- function = "i2c1";
- };
-
- pwm0_pins: pwm0 {
- groups = "pwm0_c";
- function = "pwm0";
- };
-
- pwm1_pins: pwm1 {
- groups = "pwm1_c";
- function = "pwm1";
- };
-
- scif2_pins: scif2 {
- groups = "scif2_data";
- function = "scif2";
- };
-
- sdhi2_pins: sd2 {
- groups = "mmc_data8", "mmc_ctrl";
- function = "mmc";
- power-source = <1800>;
- };
-
- sdhi2_pins_uhs: sd2_uhs {
- groups = "mmc_data8", "mmc_ctrl";
- function = "mmc";
- power-source = <1800>;
- };
-
- usb0_pins: usb0 {
- groups = "usb0";
- function = "usb0";
- };
-
- vin4_pins_cvbs: vin4 {
- groups = "vin4_data8", "vin4_sync", "vin4_clk";
- function = "vin4";
- };
-};
-
-&pwm0 {
- pinctrl-0 = <&pwm0_pins>;
- pinctrl-names = "default";
-
- status = "okay";
-};
-
-&pwm1 {
- pinctrl-0 = <&pwm1_pins>;
- pinctrl-names = "default";
-
- status = "okay";
-};
-
-&rwdt {
- timeout-sec = <60>;
- status = "okay";
-};
-
-&scif2 {
- pinctrl-0 = <&scif2_pins>;
- pinctrl-names = "default";
-
- status = "okay";
-};
-
-&sdhi2 {
- /* used for on-board eMMC */
- pinctrl-0 = <&sdhi2_pins>;
- pinctrl-1 = <&sdhi2_pins_uhs>;
- pinctrl-names = "default", "state_uhs";
-
- vmmc-supply = <®_3p3v>;
- vqmmc-supply = <®_1p8v>;
- bus-width = <8>;
- mmc-hs200-1_8v;
- non-removable;
- status = "okay";
-};
-
-&usb2_phy0 {
- pinctrl-0 = <&usb0_pins>;
- pinctrl-names = "default";
-
- renesas,no-otg-pins;
- status = "okay";
-};
-
-&vin4 {
- pinctrl-0 = <&vin4_pins_cvbs>;
- pinctrl-names = "default";
-
- status = "okay";
-
- ports {
- port {
- vin4_in: endpoint {
- remote-endpoint = <&adv7180_out>;
- };
- };
- };
};