ARM: remove duplicated code for LaCie boards
This patch groups together all the common functions for LaCie boards:
Ethernet PHY and MAC address initializations.
Moreover the configurations for LaCie Kirkwood boards are merged into
a single file: include/configs/lacie_kw.h
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
diff --git a/board/LaCie/common/common.c b/board/LaCie/common/common.c
new file mode 100644
index 0000000..dc5350d
--- /dev/null
+++ b/board/LaCie/common/common.c
@@ -0,0 +1,87 @@
+/*
+ * Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <miiphy.h>
+
+#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
+
+#define MV88E1116_LED_FCTRL_REG 10
+#define MV88E1116_CPRSP_CR3_REG 21
+#define MV88E1116_MAC_CTRL_REG 21
+#define MV88E1116_PGADR_REG 22
+#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
+#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
+
+void mv_phy_88e1116_init(const char *name)
+{
+ u16 reg;
+ u16 devadr;
+
+ if (miiphy_set_current_dev(name))
+ return;
+
+ /* command to read PHY dev address */
+ if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
+ printf("Err..(%s) could not read PHY dev address\n", __func__);
+ return;
+ }
+
+ /*
+ * Enable RGMII delay on Tx and Rx for CPU port
+ * Ref: sec 4.7.2 of chip datasheet
+ */
+ miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
+ miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®);
+ reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
+ miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
+ miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
+
+ /* reset the phy */
+ miiphy_reset(name, devadr);
+
+ printf("88E1116 Initialized on %s\n", name);
+}
+#endif /* CONFIG_CMD_NET && CONFIG_RESET_PHY_R */
+
+#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
+int lacie_read_mac_address(uchar *mac_addr)
+{
+ int ret;
+ ushort version;
+
+ /* I2C-0 for on-board EEPROM */
+ i2c_set_bus_num(0);
+
+ /* Check layout version for EEPROM data */
+ ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0,
+ CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
+ (uchar *) &version, 2);
+ if (ret != 0) {
+ printf("Error: failed to read I2C EEPROM @%02x\n",
+ CONFIG_SYS_I2C_EEPROM_ADDR);
+ return ret;
+ }
+ version = be16_to_cpu(version);
+ if (version < 1 || version > 3) {
+ printf("Error: unknown version %d for EEPROM data\n",
+ version);
+ return -1;
+ }
+
+ /* Read Ethernet MAC address from EEPROM */
+ ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 2,
+ CONFIG_SYS_I2C_EEPROM_ADDR_LEN, mac_addr, 6);
+ if (ret != 0)
+ printf("Error: failed to read I2C EEPROM @%02x\n",
+ CONFIG_SYS_I2C_EEPROM_ADDR);
+ return ret;
+}
+#endif /* CONFIG_CMD_I2C && CONFIG_SYS_I2C_EEPROM_ADDR */
diff --git a/board/LaCie/common/common.h b/board/LaCie/common/common.h
new file mode 100644
index 0000000..82a9522
--- /dev/null
+++ b/board/LaCie/common/common.h
@@ -0,0 +1,20 @@
+/*
+ * Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#ifndef _LACIE_COMMON_H
+#define _LACIE_COMMON_H
+
+#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
+void mv_phy_88e1116_init(const char *name);
+#endif
+#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
+int lacie_read_mac_address(uchar *mac);
+#endif
+
+#endif /* _LACIE_COMMON_H */
diff --git a/board/LaCie/edminiv2/Makefile b/board/LaCie/edminiv2/Makefile
index 00a255d..c8d45f4 100644
--- a/board/LaCie/edminiv2/Makefile
+++ b/board/LaCie/edminiv2/Makefile
@@ -26,10 +26,13 @@
#
include $(TOPDIR)/config.mk
+ifneq ($(OBJTREE),$(SRCTREE))
+$(shell mkdir -p $(obj)../common)
+endif
LIB = $(obj)lib$(BOARD).o
-COBJS := edminiv2.o
+COBJS := edminiv2.o ../common/common.o
SRCS := $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS))
diff --git a/board/LaCie/edminiv2/edminiv2.c b/board/LaCie/edminiv2/edminiv2.c
index ee26893..c1a01bc 100644
--- a/board/LaCie/edminiv2/edminiv2.c
+++ b/board/LaCie/edminiv2/edminiv2.c
@@ -27,7 +27,6 @@
#include <common.h>
#include <miiphy.h>
#include <asm/arch/orion5x.h>
-#include "edminiv2.h"
DECLARE_GLOBAL_DATA_PTR;
@@ -96,33 +95,6 @@
/* Configure and enable MV88E1116 PHY */
void reset_phy(void)
{
- u16 reg;
- u16 devadr;
- char *name = "egiga0";
-
- if (miiphy_set_current_dev(name))
- return;
-
- /* command to read PHY dev address */
- if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
- printf("Err..%s could not read PHY dev address\n",
- __func__);
- return;
- }
-
- /*
- * Enable RGMII delay on Tx and Rx for CPU port
- * Ref: sec 4.7.2 of chip datasheet
- */
- miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
- miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®);
- reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
- miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
- miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
-
- /* reset the phy */
- miiphy_reset(name, devadr);
-
- printf("88E1116 Initialized on %s\n", name);
+ mv_phy_88e1116_init("egiga0");
}
#endif /* CONFIG_RESET_PHY_R */
diff --git a/board/LaCie/edminiv2/edminiv2.h b/board/LaCie/edminiv2/edminiv2.h
deleted file mode 100644
index 88e62b2..0000000
--- a/board/LaCie/edminiv2/edminiv2.h
+++ /dev/null
@@ -1,41 +0,0 @@
-/*
- * (C) Copyright 2009
- * Net Insight <www.netinsight.net>
- * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
- *
- * Based on sheevaplug.h:
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301 USA
- */
-
-#ifndef __EDMINIV2_BASE_H
-#define __EDMINIV2_BASE_H
-
-/* PHY related */
-#define MV88E1116_LED_FCTRL_REG 10
-#define MV88E1116_CPRSP_CR3_REG 21
-#define MV88E1116_MAC_CTRL_REG 21
-#define MV88E1116_PGADR_REG 22
-#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
-#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
-
-#endif /* __EDMINIV2_BASE_H */
diff --git a/board/LaCie/net2big_v2/Makefile b/board/LaCie/net2big_v2/Makefile
index 4bacef4..fbae48e 100644
--- a/board/LaCie/net2big_v2/Makefile
+++ b/board/LaCie/net2big_v2/Makefile
@@ -21,10 +21,13 @@
#
include $(TOPDIR)/config.mk
+ifneq ($(OBJTREE),$(SRCTREE))
+$(shell mkdir -p $(obj)../common)
+endif
LIB = $(obj)lib$(BOARD).o
-COBJS := net2big_v2.o
+COBJS := $(BOARD).o ../common/common.o
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS))
diff --git a/board/LaCie/net2big_v2/net2big_v2.c b/board/LaCie/net2big_v2/net2big_v2.c
index 16d1405..d0b4adf 100644
--- a/board/LaCie/net2big_v2/net2big_v2.c
+++ b/board/LaCie/net2big_v2/net2big_v2.c
@@ -21,15 +21,14 @@
*/
#include <common.h>
-#include <miiphy.h>
-#include <netdev.h>
#include <command.h>
-#include <i2c.h>
#include <asm/arch/cpu.h>
#include <asm/arch/kirkwood.h>
#include <asm/arch/mpp.h>
#include <asm/arch/gpio.h>
+
#include "net2big_v2.h"
+#include "../common/common.h"
DECLARE_GLOBAL_DATA_PTR;
@@ -92,91 +91,29 @@
return 0;
}
+#if defined(CONFIG_MISC_INIT_R)
int misc_init_r(void)
{
-#ifdef CONFIG_CMD_I2C
+#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
if (!getenv("ethaddr")) {
- ushort version;
uchar mac[6];
- int ret;
-
- /* I2C-0 for on-board EEPROM */
- i2c_set_bus_num(0);
-
- /* Check layout version for EEPROM data */
- ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0,
- CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
- (uchar *) &version, 2);
- if (ret != 0) {
- printf("Error: failed to read I2C EEPROM @%02x\n",
- CONFIG_SYS_I2C_EEPROM_ADDR);
- return ret;
- }
- version = be16_to_cpu(version);
- if (version < 1 || version > 3) {
- printf("Error: unknown version %d for EEPROM data\n",
- version);
- return -1;
- }
-
- /* Read Ethernet MAC address from EEPROM */
- ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 2,
- CONFIG_SYS_I2C_EEPROM_ADDR_LEN, mac, 6);
- if (ret != 0) {
- printf("Error: failed to read I2C EEPROM @%02x\n",
- CONFIG_SYS_I2C_EEPROM_ADDR);
- return ret;
- }
- eth_setenv_enetaddr("ethaddr", mac);
+ if (lacie_read_mac_address(mac) == 0)
+ eth_setenv_enetaddr("ethaddr", mac);
}
-#endif /* CONFIG_CMD_I2C */
-
+#endif
return 0;
}
+#endif
-void mv_phy_88e1116_init(char *name)
-{
- u16 reg;
- u16 devadr;
-
- if (miiphy_set_current_dev(name))
- return;
-
- /* command to read PHY dev address */
- if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
- printf("Err..(%s) could not read PHY dev address\n", __func__);
- return;
- }
-
- /*
- * Enable RGMII delay on Tx and Rx for CPU port
- * Ref: sec 4.7.2 of chip datasheet
- */
- miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
- miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®);
- reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
- miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
- miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
-
- /* reset the phy */
- if (miiphy_read(name, devadr, MII_BMCR, ®) != 0) {
- printf("Err..(%s) PHY status read failed\n", __func__);
- return;
- }
- if (miiphy_write(name, devadr, MII_BMCR, reg | 0x8000) != 0) {
- printf("Err..(%s) PHY reset failed\n", __func__);
- return;
- }
-
- debug("88E1116 Initialized on %s\n", name);
-}
-
+#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
/* Configure and initialize PHY */
void reset_phy(void)
{
mv_phy_88e1116_init("egiga0");
}
+#endif
+#if defined(CONFIG_KIRKWOOD_GPIO)
/* Return GPIO push button status */
static int
do_read_push_button(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
@@ -186,3 +123,4 @@
U_BOOT_CMD(button, 1, 1, do_read_push_button,
"Return GPIO push button status 0=off 1=on", "");
+#endif
diff --git a/board/LaCie/net2big_v2/net2big_v2.h b/board/LaCie/net2big_v2/net2big_v2.h
index bbe67af..f9778f4 100644
--- a/board/LaCie/net2big_v2/net2big_v2.h
+++ b/board/LaCie/net2big_v2/net2big_v2.h
@@ -32,12 +32,4 @@
/* Buttons */
#define NET2BIG_V2_GPIO_PUSH_BUTTON 34
-/* PHY related */
-#define MV88E1116_LED_FCTRL_REG 10
-#define MV88E1116_CPRSP_CR3_REG 21
-#define MV88E1116_MAC_CTRL_REG 21
-#define MV88E1116_PGADR_REG 22
-#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
-#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
-
#endif /* NET2BIG_V2_H */
diff --git a/board/LaCie/netspace_v2/Makefile b/board/LaCie/netspace_v2/Makefile
index d4a613f..b43c3d3 100644
--- a/board/LaCie/netspace_v2/Makefile
+++ b/board/LaCie/netspace_v2/Makefile
@@ -21,10 +21,13 @@
#
include $(TOPDIR)/config.mk
+ifneq ($(OBJTREE),$(SRCTREE))
+$(shell mkdir -p $(obj)../common)
+endif
LIB = $(obj)lib$(BOARD).o
-COBJS := netspace_v2.o
+COBJS := $(BOARD).o ../common/common.o
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS))
diff --git a/board/LaCie/netspace_v2/netspace_v2.c b/board/LaCie/netspace_v2/netspace_v2.c
index 6938a43..fbf020f 100644
--- a/board/LaCie/netspace_v2/netspace_v2.c
+++ b/board/LaCie/netspace_v2/netspace_v2.c
@@ -21,15 +21,14 @@
*/
#include <common.h>
-#include <miiphy.h>
-#include <netdev.h>
#include <command.h>
-#include <i2c.h>
#include <asm/arch/cpu.h>
#include <asm/arch/kirkwood.h>
#include <asm/arch/mpp.h>
#include <asm/arch/gpio.h>
+
#include "netspace_v2.h"
+#include "../common/common.h"
DECLARE_GLOBAL_DATA_PTR;
@@ -90,91 +89,29 @@
return 0;
}
+#if defined(CONFIG_MISC_INIT_R)
int misc_init_r(void)
{
#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
if (!getenv("ethaddr")) {
- ushort version;
uchar mac[6];
- int ret;
-
- /* I2C-0 for on-board EEPROM */
- i2c_set_bus_num(0);
-
- /* Check layout version for EEPROM data */
- ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0,
- CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
- (uchar *) &version, 2);
- if (ret != 0) {
- printf("Error: failed to read I2C EEPROM @%02x\n",
- CONFIG_SYS_I2C_EEPROM_ADDR);
- return ret;
- }
- version = be16_to_cpu(version);
- if (version < 1 || version > 3) {
- printf("Error: unknown version %d for EEPROM data\n",
- version);
- return -1;
- }
-
- /* Read Ethernet MAC address from EEPROM */
- ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 2,
- CONFIG_SYS_I2C_EEPROM_ADDR_LEN, mac, 6);
- if (ret != 0) {
- printf("Error: failed to read I2C EEPROM @%02x\n",
- CONFIG_SYS_I2C_EEPROM_ADDR);
- return ret;
- }
- eth_setenv_enetaddr("ethaddr", mac);
+ if (lacie_read_mac_address(mac) == 0)
+ eth_setenv_enetaddr("ethaddr", mac);
}
-#endif /* CONFIG_CMD_I2C && CONFIG_SYS_I2C_EEPROM_ADDR */
-
+#endif
return 0;
}
+#endif
-void mv_phy_88e1116_init(char *name)
-{
- u16 reg;
- u16 devadr;
-
- if (miiphy_set_current_dev(name))
- return;
-
- /* command to read PHY dev address */
- if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
- printf("Err..(%s) could not read PHY dev address\n", __func__);
- return;
- }
-
- /*
- * Enable RGMII delay on Tx and Rx for CPU port
- * Ref: sec 4.7.2 of chip datasheet
- */
- miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
- miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®);
- reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
- miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
- miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
-
- /* reset the phy */
- if (miiphy_read(name, devadr, MII_BMCR, ®) != 0) {
- printf("Err..(%s) PHY status read failed\n", __func__);
- return;
- }
- if (miiphy_write(name, devadr, MII_BMCR, reg | 0x8000) != 0) {
- printf("Err..(%s) PHY reset failed\n", __func__);
- return;
- }
-
- debug("88E1116 Initialized on %s\n", name);
-}
-
+#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
/* Configure and initialize PHY */
void reset_phy(void)
{
mv_phy_88e1116_init("egiga0");
}
+#endif
+#if defined(CONFIG_KIRKWOOD_GPIO)
/* Return GPIO button status */
static int
do_read_button(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
@@ -184,3 +121,4 @@
U_BOOT_CMD(button, 1, 1, do_read_button,
"Return GPIO button status 0=off 1=on", "");
+#endif
diff --git a/board/LaCie/netspace_v2/netspace_v2.h b/board/LaCie/netspace_v2/netspace_v2.h
index 3f3d51c..34e492c 100644
--- a/board/LaCie/netspace_v2/netspace_v2.h
+++ b/board/LaCie/netspace_v2/netspace_v2.h
@@ -31,12 +31,4 @@
#define NETSPACE_V2_GPIO_BUTTON 32
-/* PHY related */
-#define MV88E1116_LED_FCTRL_REG 10
-#define MV88E1116_CPRSP_CR3_REG 21
-#define MV88E1116_MAC_CTRL_REG 21
-#define MV88E1116_PGADR_REG 22
-#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
-#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
-
#endif /* NETSPACE_V2_H */