* Patches by Jon Diekema, 15 Sep 2003:
- add description for missing CFG_CMD_* entries in the README file
- sacsng tweaks:
include/configs/sacsng.h:
+ Support extra bootp options like: 2nd DNS and send hostname
+ Enabling ping and irq command
+ Adding defines for a bunch of misc configrabled options
(patches for these options will be coming)
+ Adding watchdog support, but it isn't enabled yet.
board/sacsng/sacsng.c:
+ Suppressing unneeded output when the quiet environment
is non-zero.
+ show_boot_progress() now accepts any negative number as a
failure code.
+ show_boot_progress() flashes the error code 5 times, and
then resets the board to retry the boot from the top
* Patch by Gleb Natapov, 14 Sep 2003:
enable watchdog support for all MPC824x boards that have a watchdog
diff --git a/board/sacsng/sacsng.c b/board/sacsng/sacsng.c
index eb7e416..60563d4 100644
--- a/board/sacsng/sacsng.c
+++ b/board/sacsng/sacsng.c
@@ -28,11 +28,18 @@
#include <mpc8260.h>
#include <i2c.h>
#include <spi.h>
+#include <command.h>
#ifdef CONFIG_SHOW_BOOT_PROGRESS
#include <status_led.h>
#endif
+#ifdef CONFIG_ETHER_LOOPBACK_TEST
+extern void eth_loopback_test(void);
+#endif /* CONFIG_ETHER_LOOPBACK_TEST */
+
+extern int do_reset(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);
+
#include "clkinit.h"
#include "ioconfig.h" /* I/O configuration table */
@@ -243,15 +250,15 @@
/* We don't trust CL less than 2 (only saw it on an old 16MByte DIMM) */
if(caslatency < 2) {
- printf("CL was %d, forcing to 2\n", caslatency);
+ printf("WARNING: CL was %d, forcing to 2\n", caslatency);
caslatency = 2;
}
if(rows > 14) {
- printf("This doesn't look good, rows = %d, should be <= 14\n", rows);
+ printf("WARNING: This doesn't look good, rows = %d, should be <= 14\n", rows);
rows = 14;
}
if(cols > 11) {
- printf("This doesn't look good, columns = %d, should be <= 11\n", cols);
+ printf("WARNING: This doesn't look good, columns = %d, should be <= 11\n", cols);
cols = 11;
}
@@ -450,6 +457,15 @@
int sample_128x; /* Use 128/4 clocking for the ADC/DAC */
int right_just; /* Is the data to the DAC right justified? */
int mclk_divide; /* MCLK Divide */
+ int quiet; /* Quiet or minimal output mode */
+
+ quiet = 0;
+ if ((ep = getenv("quiet")) != NULL) {
+ quiet = simple_strtol(ep, NULL, 10);
+ }
+ else {
+ setenv("quiet", "0");
+ }
/*
* SACSng custom initialization:
@@ -517,8 +533,12 @@
setenv("Daq128xSampling", "1");
}
- /* Display the ADC/DAC clocking information */
- Daq_Display_Clocks();
+ /*
+ * Display the ADC/DAC clocking information
+ */
+ if (!quiet) {
+ Daq_Display_Clocks();
+ }
/*
* Determine the DAC data justification
@@ -552,8 +572,10 @@
* 3) Write the I2C address to register 6
* 4) Enable address matching by setting the MSB in register 7
*/
-
- printf("Initializing the ADC...\n");
+
+ if (!quiet) {
+ printf("Initializing the ADC...\n");
+ }
udelay(ADC_INITIAL_DELAY); /* 10uSec per uF of VREF cap */
iopa->pdat &= ~ADC_SDATA1_MASK; /* release SDATA1 */
@@ -615,7 +637,9 @@
* sending an I2C "start" sequence. When we bring the I2C back to
* the normal state, we send an I2C "stop" sequence.
*/
- printf("Initializing the DAC...\n");
+ if (!quiet) {
+ printf("Initializing the DAC...\n");
+ }
/*
* Bring the I2C clock and data lines low for initialization
@@ -695,7 +719,16 @@
I2C_DELAY;
I2C_TRISTATE;
- printf("\n");
+ if (!quiet) {
+ printf("\n");
+ }
+
+#ifdef CONFIG_ETHER_LOOPBACK_TEST
+ /*
+ * Run the Ethernet loopback test
+ */
+ eth_loopback_test ();
+#endif /* CONFIG_ETHER_LOOPBACK_TEST */
#ifdef CONFIG_SHOW_BOOT_PROGRESS
/*
@@ -758,17 +791,44 @@
void show_boot_progress (int status)
{
- if(status != -1) {
+ int i,j;
+ if(status > 0) {
last_boot_progress = status;
} else {
- /*
- * Houston, we have a problem. Blink the last OK status which
- * indicates where things failed.
+ /*
+ * If a specific failure code is given, flash this code
+ * else just use the last success code we've seen
*/
- status_led_set(STATUS_LED_RED, STATUS_LED_ON);
- flash_code(last_boot_progress, 5, 3);
- udelay(1000000);
- status_led_set(STATUS_LED_RED, STATUS_LED_BLINKING);
+ if(status < -1)
+ last_boot_progress = -status;
+
+ /*
+ * Flash this code 5 times
+ */
+ for(j=0; j<5; j++) {
+ /*
+ * Houston, we have a problem.
+ * Blink the last OK status which indicates where things failed.
+ */
+ status_led_set(STATUS_LED_RED, STATUS_LED_ON);
+ flash_code(last_boot_progress, 5, 3);
+
+ /*
+ * Delay 5 seconds between repetitions,
+ * with the fault LED blinking
+ */
+ for(i=0; i<5; i++) {
+ status_led_set(STATUS_LED_RED, STATUS_LED_OFF);
+ udelay(500000);
+ status_led_set(STATUS_LED_RED, STATUS_LED_ON);
+ udelay(500000);
+ }
+ }
+
+ /*
+ * Reset the board to retry initialization.
+ */
+ do_reset (NULL, 0, 0, NULL);
}
}
#endif /* CONFIG_SHOW_BOOT_PROGRESS */