GCC4.6: Use debug() instead of debugX() in s3c24xx_nand.c
The debugX() macro was always used with debug level 1. There is no point to use
it here instead of debug().
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
diff --git a/drivers/mtd/nand/s3c2410_nand.c b/drivers/mtd/nand/s3c2410_nand.c
index 27351fb..e1a459b 100644
--- a/drivers/mtd/nand/s3c2410_nand.c
+++ b/drivers/mtd/nand/s3c2410_nand.c
@@ -56,7 +56,7 @@
struct nand_chip *chip = mtd->priv;
struct s3c2410_nand *nand = s3c2410_get_base_nand();
- debugX(1, "hwcontrol(): 0x%02x 0x%02x\n", cmd, ctrl);
+ debug("hwcontrol(): 0x%02x 0x%02x\n", cmd, ctrl);
if (ctrl & NAND_CTRL_CHANGE) {
ulong IO_ADDR_W = (ulong)nand;
@@ -83,7 +83,7 @@
static int s3c2410_dev_ready(struct mtd_info *mtd)
{
struct s3c2410_nand *nand = s3c2410_get_base_nand();
- debugX(1, "dev_ready\n");
+ debug("dev_ready\n");
return readl(&nand->nfstat) & 0x01;
}
@@ -91,7 +91,7 @@
void s3c2410_nand_enable_hwecc(struct mtd_info *mtd, int mode)
{
struct s3c2410_nand *nand = s3c2410_get_base_nand();
- debugX(1, "s3c2410_nand_enable_hwecc(%p, %d)\n", mtd, mode);
+ debug("s3c2410_nand_enable_hwecc(%p, %d)\n", mtd, mode);
writel(readl(&nand->nfconf) | S3C2410_NFCONF_INITECC, &nand->nfconf);
}
@@ -102,7 +102,7 @@
ecc_code[0] = readb(&nand->nfecc);
ecc_code[1] = readb(&nand->nfecc + 1);
ecc_code[2] = readb(&nand->nfecc + 2);
- debugX(1, "s3c2410_nand_calculate_hwecc(%p,): 0x%02x 0x%02x 0x%02x\n",
+ debug("s3c2410_nand_calculate_hwecc(%p,): 0x%02x 0x%02x 0x%02x\n",
mtd , ecc_code[0], ecc_code[1], ecc_code[2]);
return 0;
@@ -128,7 +128,7 @@
struct s3c24x0_clock_power *clk_power = s3c24x0_get_base_clock_power();
struct s3c2410_nand *nand_reg = s3c2410_get_base_nand();
- debugX(1, "board_nand_init()\n");
+ debug("board_nand_init()\n");
writel(readl(&clk_power->clkcon) | (1 << 4), &clk_power->clkcon);
@@ -183,7 +183,7 @@
nand->options = 0;
#endif
- debugX(1, "end of nand_init\n");
+ debug("end of nand_init\n");
return 0;
}