include/configs/ls1021atsn.h - platform/external/u-boot - Gitiles

 /* SPDX-License-Identifier: GPL-2.0
  * Copyright 2016-2019 NXP Semiconductors
  * Copyright 2019 Vladimir Oltean <olteanv@gmail.com>
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 #define CONFIG_ARMV7_SECURE_BASE	OCRAM_BASE_S_ADDR

 #define CONFIG_SYS_FSL_CLK

 #define CONFIG_DEEP_SLEEP

 #define CONFIG_SYS_INIT_RAM_ADDR	OCRAM_BASE_ADDR
 #define CONFIG_SYS_INIT_RAM_SIZE	OCRAM_SIZE

 /* XHCI Support - enabled by default */
 #define CONFIG_USB_MAX_CONTROLLER_COUNT	1

 #define CONFIG_SYS_CLK_FREQ		100000000

 #define DDR_SDRAM_CFG			0x470c0008
 #define DDR_CS0_BNDS			0x008000bf
 #define DDR_CS0_CONFIG			0x80014302
 #define DDR_TIMING_CFG_0		0x50550004
 #define DDR_TIMING_CFG_1		0xbcb38c56
 #define DDR_TIMING_CFG_2		0x0040d120
 #define DDR_TIMING_CFG_3		0x010e1000
 #define DDR_TIMING_CFG_4		0x00000001
 #define DDR_TIMING_CFG_5		0x03401400
 #define DDR_SDRAM_CFG_2			0x00401010
 #define DDR_SDRAM_MODE			0x00061c60
 #define DDR_SDRAM_MODE_2		0x00180000
 #define DDR_SDRAM_INTERVAL		0x18600618
 #define DDR_DDR_WRLVL_CNTL		0x8655f605
 #define DDR_DDR_WRLVL_CNTL_2		0x05060607
 #define DDR_DDR_WRLVL_CNTL_3		0x05050505
 #define DDR_DDR_CDR1			0x80040000
 #define DDR_DDR_CDR2			0x00000001
 #define DDR_SDRAM_CLK_CNTL		0x02000000
 #define DDR_DDR_ZQ_CNTL			0x89080600
 #define DDR_CS0_CONFIG_2		0
 #define DDR_SDRAM_CFG_MEM_EN		0x80000000
 #define SDRAM_CFG2_D_INIT		0x00000010
 #define DDR_CDR2_VREF_TRAIN_EN		0x00000080
 #define SDRAM_CFG2_FRC_SR		0x80000000
 #define SDRAM_CFG_BI			0x00000001

 #ifdef CONFIG_SD_BOOT
 #ifdef CONFIG_NXP_ESBC
 #define CONFIG_U_BOOT_HDR_SIZE		(16 << 10)
 #endif /* ifdef CONFIG_NXP_ESBC */

 #define CONFIG_SPL_MAX_SIZE		0x1a000
 #define CONFIG_SPL_STACK		0x1001d000
 #define CONFIG_SPL_PAD_TO		0x1c000

 #define CONFIG_SYS_SPL_MALLOC_START	(CONFIG_SYS_TEXT_BASE + \
 		CONFIG_SYS_MONITOR_LEN)
 #define CONFIG_SYS_SPL_MALLOC_SIZE	0x100000
 #define CONFIG_SPL_BSS_START_ADDR	0x80100000
 #define CONFIG_SPL_BSS_MAX_SIZE		0x80000

 #ifdef CONFIG_U_BOOT_HDR_SIZE
 /*
  * HDR would be appended at end of image and copied to DDR along
  * with U-Boot image. Here u-boot max. size is 512K. So if binary
  * size increases then increase this size in case of secure boot as
  * it uses raw U-Boot image instead of FIT image.
  */
 #define CONFIG_SYS_MONITOR_LEN		(0x100000 + CONFIG_U_BOOT_HDR_SIZE)
 #else
 #define CONFIG_SYS_MONITOR_LEN		0x100000
 #endif /* ifdef CONFIG_U_BOOT_HDR_SIZE */
 #endif

 #define CONFIG_NR_DRAM_BANKS		1
 #define PHYS_SDRAM			0x80000000
 #define PHYS_SDRAM_SIZE			(1u * 1024 * 1024 * 1024)

 #define CONFIG_SYS_DDR_SDRAM_BASE	0x80000000UL
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE

 #define CONFIG_CHIP_SELECTS_PER_CTRL	4

 /* Serial Port */
 #define CONFIG_SYS_NS16550_SERIAL
 #ifndef CONFIG_DM_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #endif
 #define CONFIG_SYS_NS16550_CLK		get_serial_clock()

 /* I2C */

 /* EEPROM */
 #define CONFIG_SYS_I2C_EEPROM_NXID
 #define CONFIG_SYS_EEPROM_BUS_NUM	0

 /* QSPI */
 #define FSL_QSPI_FLASH_SIZE		(1 << 24)
 #define FSL_QSPI_FLASH_NUM		2

 /* PCIe */
 #define CONFIG_PCIE1			/* PCIE controller 1 */
 #define CONFIG_PCIE2			/* PCIE controller 2 */
 #define FSL_PCIE_COMPAT			"fsl,ls1021a-pcie"
 #ifdef CONFIG_PCI
 #define CONFIG_PCI_SCAN_SHOW
 #endif

 #define CONFIG_LAYERSCAPE_NS_ACCESS
 #define COUNTER_FREQUENCY		12500000

 #define CONFIG_HWCONFIG
 #define HWCONFIG_BUFFER_SIZE		256

 #define CONFIG_FSL_DEVICE_DISABLE

 #define BOOT_TARGET_DEVICES(func) \
 	func(MMC, mmc, 0) \
 	func(USB, usb, 0) \
 	func(DHCP, dhcp, na)
 #include <config_distro_bootcmd.h>

 #define CONFIG_EXTRA_ENV_SETTINGS					\
 	"bootargs=root=/dev/ram0 rw console=ttyS0,115200\0"		\
 	"initrd_high=0xffffffff\0"					\
 	"fdt_addr=0x64f00000\0"						\
 	"kernel_addr=0x61000000\0"					\
 	"kernelheader_addr=0x60800000\0"				\
 	"scriptaddr=0x80000000\0"					\
 	"scripthdraddr=0x80080000\0"					\
 	"fdtheader_addr_r=0x80100000\0"					\
 	"kernelheader_addr_r=0x80200000\0"				\
 	"kernel_addr_r=0x80008000\0"					\
 	"kernelheader_size=0x40000\0"					\
 	"fdt_addr_r=0x8f000000\0"					\
 	"ramdisk_addr_r=0xa0000000\0"					\
 	"load_addr=0x80008000\0"					\
 	"kernel_size=0x2800000\0"					\
 	"kernel_addr_sd=0x8000\0"					\
 	"kernel_size_sd=0x14000\0"					\
 	"kernelhdr_addr_sd=0x4000\0"					\
 	"kernelhdr_size_sd=0x10\0"					\
 	BOOTENV								\
 	"boot_scripts=ls1021atsn_boot.scr\0"				\
 	"boot_script_hdr=hdr_ls1021atsn_bs.out\0"			\
 		"scan_dev_for_boot_part="				\
 			"part list ${devtype} ${devnum} devplist; "	\
 			"env exists devplist || setenv devplist 1; "	\
 			"for distro_bootpart in ${devplist}; do "	\
 			"if fstype ${devtype} "				\
 				"${devnum}:${distro_bootpart} "		\
 				"bootfstype; then "			\
 				"run scan_dev_for_boot; "		\
 			"fi; "						\
 		"done\0"						\
 	"scan_dev_for_boot="						\
 		"echo Scanning ${devtype} "				\
 				"${devnum}:${distro_bootpart}...; "	\
 		"for prefix in ${boot_prefixes}; do "			\
 			"run scan_dev_for_scripts; "			\
 			"run scan_dev_for_extlinux; "			\
 		"done;"							\
 		"\0"							\
 	"boot_a_script="						\
 		"load ${devtype} ${devnum}:${distro_bootpart} "		\
 			"${scriptaddr} ${prefix}${script}; "		\
 		"env exists secureboot && load ${devtype} "		\
 			"${devnum}:${distro_bootpart} "			\
 			"${scripthdraddr} ${prefix}${boot_script_hdr} "	\
 			"&& esbc_validate ${scripthdraddr};"		\
 		"source ${scriptaddr}\0"				\
 	"qspi_bootcmd=echo Trying load from qspi..;"			\
 		"sf probe && sf read $load_addr "			\
 		"$kernel_addr $kernel_size; env exists secureboot "	\
 		"&& sf read $kernelheader_addr_r $kernelheader_addr "	\
 		"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
 		"bootm $load_addr#$board\0"				\
 	"sd_bootcmd=echo Trying load from SD ..;"			\
 		"mmcinfo && mmc read $load_addr "			\
 		"$kernel_addr_sd $kernel_size_sd && "			\
 		"env exists secureboot && mmc read $kernelheader_addr_r " \
 		"$kernelhdr_addr_sd $kernelhdr_size_sd "		\
 		" && esbc_validate ${kernelheader_addr_r};"		\
 		"bootm $load_addr#$board\0"

 /* Miscellaneous configurable options */
 #define CONFIG_SYS_BOOTMAPSZ		(256 << 20)

 #define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */
 #define CONFIG_SYS_PBSIZE		\
 		(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_MAXARGS		16	/* max number of command args */
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE

 #define CONFIG_LS102XA_STREAM_ID

 #define CONFIG_SYS_INIT_SP_OFFSET \
 	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_ADDR \
 	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

 #ifdef CONFIG_SPL_BUILD
 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
 #else
 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
 #endif

 /* Environment */

 #define CONFIG_SYS_BOOTM_LEN		0x8000000 /* 128 MB */

 #endif
	/* SPDX-License-Identifier: GPL-2.0
	* Copyright 2016-2019 NXP Semiconductors
	* Copyright 2019 Vladimir Oltean <olteanv@gmail.com>
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	#define CONFIG_ARMV7_SECURE_BASE OCRAM_BASE_S_ADDR

	#define CONFIG_SYS_FSL_CLK

	#define CONFIG_DEEP_SLEEP

	#define CONFIG_SYS_INIT_RAM_ADDR OCRAM_BASE_ADDR
	#define CONFIG_SYS_INIT_RAM_SIZE OCRAM_SIZE

	/* XHCI Support - enabled by default */
	#define CONFIG_USB_MAX_CONTROLLER_COUNT 1

	#define CONFIG_SYS_CLK_FREQ 100000000

	#define DDR_SDRAM_CFG 0x470c0008
	#define DDR_CS0_BNDS 0x008000bf
	#define DDR_CS0_CONFIG 0x80014302
	#define DDR_TIMING_CFG_0 0x50550004
	#define DDR_TIMING_CFG_1 0xbcb38c56
	#define DDR_TIMING_CFG_2 0x0040d120
	#define DDR_TIMING_CFG_3 0x010e1000
	#define DDR_TIMING_CFG_4 0x00000001
	#define DDR_TIMING_CFG_5 0x03401400
	#define DDR_SDRAM_CFG_2 0x00401010
	#define DDR_SDRAM_MODE 0x00061c60
	#define DDR_SDRAM_MODE_2 0x00180000
	#define DDR_SDRAM_INTERVAL 0x18600618
	#define DDR_DDR_WRLVL_CNTL 0x8655f605
	#define DDR_DDR_WRLVL_CNTL_2 0x05060607
	#define DDR_DDR_WRLVL_CNTL_3 0x05050505
	#define DDR_DDR_CDR1 0x80040000
	#define DDR_DDR_CDR2 0x00000001
	#define DDR_SDRAM_CLK_CNTL 0x02000000
	#define DDR_DDR_ZQ_CNTL 0x89080600
	#define DDR_CS0_CONFIG_2 0
	#define DDR_SDRAM_CFG_MEM_EN 0x80000000
	#define SDRAM_CFG2_D_INIT 0x00000010
	#define DDR_CDR2_VREF_TRAIN_EN 0x00000080
	#define SDRAM_CFG2_FRC_SR 0x80000000
	#define SDRAM_CFG_BI 0x00000001

	#ifdef CONFIG_SD_BOOT
	#ifdef CONFIG_NXP_ESBC
	#define CONFIG_U_BOOT_HDR_SIZE (16 << 10)
	#endif /* ifdef CONFIG_NXP_ESBC */

	#define CONFIG_SPL_MAX_SIZE 0x1a000
	#define CONFIG_SPL_STACK 0x1001d000
	#define CONFIG_SPL_PAD_TO 0x1c000

	#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE + \
	CONFIG_SYS_MONITOR_LEN)
	#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
	#define CONFIG_SPL_BSS_START_ADDR 0x80100000
	#define CONFIG_SPL_BSS_MAX_SIZE 0x80000

	#ifdef CONFIG_U_BOOT_HDR_SIZE
	/*
	* HDR would be appended at end of image and copied to DDR along
	* with U-Boot image. Here u-boot max. size is 512K. So if binary
	* size increases then increase this size in case of secure boot as
	* it uses raw U-Boot image instead of FIT image.
	*/
	#define CONFIG_SYS_MONITOR_LEN (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
	#else
	#define CONFIG_SYS_MONITOR_LEN 0x100000
	#endif /* ifdef CONFIG_U_BOOT_HDR_SIZE */
	#endif

	#define CONFIG_NR_DRAM_BANKS 1
	#define PHYS_SDRAM 0x80000000
	#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024)

	#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL
	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE

	#define CONFIG_CHIP_SELECTS_PER_CTRL 4

	/* Serial Port */
	#define CONFIG_SYS_NS16550_SERIAL
	#ifndef CONFIG_DM_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE 1
	#endif
	#define CONFIG_SYS_NS16550_CLK get_serial_clock()

	/* I2C */

	/* EEPROM */
	#define CONFIG_SYS_I2C_EEPROM_NXID
	#define CONFIG_SYS_EEPROM_BUS_NUM 0

	/* QSPI */
	#define FSL_QSPI_FLASH_SIZE (1 << 24)
	#define FSL_QSPI_FLASH_NUM 2

	/* PCIe */
	#define CONFIG_PCIE1 /* PCIE controller 1 */
	#define CONFIG_PCIE2 /* PCIE controller 2 */
	#define FSL_PCIE_COMPAT "fsl,ls1021a-pcie"
	#ifdef CONFIG_PCI
	#define CONFIG_PCI_SCAN_SHOW
	#endif

	#define CONFIG_LAYERSCAPE_NS_ACCESS
	#define COUNTER_FREQUENCY 12500000

	#define CONFIG_HWCONFIG
	#define HWCONFIG_BUFFER_SIZE 256

	#define CONFIG_FSL_DEVICE_DISABLE

	#define BOOT_TARGET_DEVICES(func) \
	func(MMC, mmc, 0) \
	func(USB, usb, 0) \
	func(DHCP, dhcp, na)
	#include <config_distro_bootcmd.h>

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"bootargs=root=/dev/ram0 rw console=ttyS0,115200\0" \
	"initrd_high=0xffffffff\0" \
	"fdt_addr=0x64f00000\0" \
	"kernel_addr=0x61000000\0" \
	"kernelheader_addr=0x60800000\0" \
	"scriptaddr=0x80000000\0" \
	"scripthdraddr=0x80080000\0" \
	"fdtheader_addr_r=0x80100000\0" \
	"kernelheader_addr_r=0x80200000\0" \
	"kernel_addr_r=0x80008000\0" \
	"kernelheader_size=0x40000\0" \
	"fdt_addr_r=0x8f000000\0" \
	"ramdisk_addr_r=0xa0000000\0" \
	"load_addr=0x80008000\0" \
	"kernel_size=0x2800000\0" \
	"kernel_addr_sd=0x8000\0" \
	"kernel_size_sd=0x14000\0" \
	"kernelhdr_addr_sd=0x4000\0" \
	"kernelhdr_size_sd=0x10\0" \
	BOOTENV \
	"boot_scripts=ls1021atsn_boot.scr\0" \
	"boot_script_hdr=hdr_ls1021atsn_bs.out\0" \
	"scan_dev_for_boot_part=" \
	"part list ${devtype} ${devnum} devplist; " \
	"env exists devplist \|\| setenv devplist 1; " \
	"for distro_bootpart in ${devplist}; do " \
	"if fstype ${devtype} " \
	"${devnum}:${distro_bootpart} " \
	"bootfstype; then " \
	"run scan_dev_for_boot; " \
	"fi; " \
	"done\0" \
	"scan_dev_for_boot=" \
	"echo Scanning ${devtype} " \
	"${devnum}:${distro_bootpart}...; " \
	"for prefix in ${boot_prefixes}; do " \
	"run scan_dev_for_scripts; " \
	"run scan_dev_for_extlinux; " \
	"done;" \
	"\0" \
	"boot_a_script=" \
	"load ${devtype} ${devnum}:${distro_bootpart} " \
	"${scriptaddr} ${prefix}${script}; " \
	"env exists secureboot && load ${devtype} " \
	"${devnum}:${distro_bootpart} " \
	"${scripthdraddr} ${prefix}${boot_script_hdr} " \
	"&& esbc_validate ${scripthdraddr};" \
	"source ${scriptaddr}\0" \
	"qspi_bootcmd=echo Trying load from qspi..;" \
	"sf probe && sf read $load_addr " \
	"$kernel_addr $kernel_size; env exists secureboot " \
	"&& sf read $kernelheader_addr_r $kernelheader_addr " \
	"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
	"bootm $load_addr#$board\0" \
	"sd_bootcmd=echo Trying load from SD ..;" \
	"mmcinfo && mmc read $load_addr " \
	"$kernel_addr_sd $kernel_size_sd && " \
	"env exists secureboot && mmc read $kernelheader_addr_r " \
	"$kernelhdr_addr_sd $kernelhdr_size_sd " \
	" && esbc_validate ${kernelheader_addr_r};" \
	"bootm $load_addr#$board\0"

	/* Miscellaneous configurable options */
	#define CONFIG_SYS_BOOTMAPSZ (256 << 20)

	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#define CONFIG_SYS_PBSIZE \
	(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE

	#define CONFIG_LS102XA_STREAM_ID

	#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

	#ifdef CONFIG_SPL_BUILD
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
	#else
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
	#endif

	/* Environment */

	#define CONFIG_SYS_BOOTM_LEN 0x8000000 /* 128 MB */

	#endif