phy: marvell: cp110: add support for end point configuration
The serdes was always configured in root complex mode.
this patch add new entry in device tree (per serdes)
which indicates whether the serdes is in end point mode.
if so, it skips the root complex configuration.
Signed-off-by: Haim Boot <hayim@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
diff --git a/drivers/phy/marvell/comphy.h b/drivers/phy/marvell/comphy.h
index 0a15692..8b05757 100644
--- a/drivers/phy/marvell/comphy.h
+++ b/drivers/phy/marvell/comphy.h
@@ -86,6 +86,7 @@
u32 speed;
u32 invert;
bool clk_src;
+ bool end_point;
};
struct chip_serdes_phy_config {
diff --git a/drivers/phy/marvell/comphy_core.c b/drivers/phy/marvell/comphy_core.c
index 97455c8..d8877e8 100644
--- a/drivers/phy/marvell/comphy_core.c
+++ b/drivers/phy/marvell/comphy_core.c
@@ -167,6 +167,8 @@
blob, subnode, "phy-invert", PHY_POLARITY_NO_INVERT);
comphy_map_data[lane].clk_src = fdtdec_get_bool(blob, subnode,
"clk-src");
+ comphy_map_data[lane].end_point = fdtdec_get_bool(blob, subnode,
+ "end_point");
if (comphy_map_data[lane].type == PHY_TYPE_INVALID) {
printf("no phy type for lane %d, setting lane as unconnected\n",
lane + 1);
diff --git a/drivers/phy/marvell/comphy_cp110.c b/drivers/phy/marvell/comphy_cp110.c
index cd3cf96..70554fe 100644
--- a/drivers/phy/marvell/comphy_cp110.c
+++ b/drivers/phy/marvell/comphy_cp110.c
@@ -87,8 +87,8 @@
return 0;
}
-static int comphy_pcie_power_up(u32 lane, u32 pcie_width,
- bool clk_src, void __iomem *hpipe_base,
+static int comphy_pcie_power_up(u32 lane, u32 pcie_width, bool clk_src,
+ bool is_end_point, void __iomem *hpipe_base,
void __iomem *comphy_base)
{
u32 mask, data, ret = 1;
@@ -109,6 +109,7 @@
* and SerDes Lane 0 got PCIe ref-clock #0
*/
debug("PCIe clock = %x\n", pcie_clk);
+ debug("PCIe RC = %d\n", !is_end_point);
debug("PCIe width = %d\n", pcie_width);
/* enable PCIe by4 and by2 */
@@ -384,10 +385,12 @@
data |= 0x1 << HPIPE_G3_FFE_LOAD_RES_LEVEL_OFFSET;
reg_set(hpipe_addr + HPIPE_G3_SETTING_3_REG, data, mask);
- /* Set phy in root complex mode */
- mask = HPIPE_CFG_PHY_RC_EP_MASK;
- data = 0x1 << HPIPE_CFG_PHY_RC_EP_OFFSET;
- reg_set(hpipe_addr + HPIPE_LANE_EQU_CONFIG_0_REG, data, mask);
+ if (!is_end_point) {
+ /* Set phy in root complex mode */
+ mask = HPIPE_CFG_PHY_RC_EP_MASK;
+ data = 0x1 << HPIPE_CFG_PHY_RC_EP_OFFSET;
+ reg_set(hpipe_addr + HPIPE_LANE_EQU_CONFIG_0_REG, data, mask);
+ }
debug("stage: Comphy power up\n");
@@ -1667,6 +1670,7 @@
case PHY_TYPE_PEX3:
ret = comphy_pcie_power_up(
lane, pcie_width, ptr_comphy_map->clk_src,
+ serdes_map->end_point,
hpipe_base_addr, comphy_base_addr);
break;
case PHY_TYPE_SATA0: