xtensa: add support for the 'xtfpga' evaluation board
The 'xtfpga' board is actually a set of FPGA evaluation boards that
can be configured to run an Xtensa processor.
- Avnet Xilinx LX60
- Avnet Xilinx LX110
- Avnet Xilinx LX200
- Xilinx ML605
- Xilinx KC705
These boards share the same components (open-ethernet, ns16550 serial,
lcd display, flash, etc.).
Signed-off-by: Chris Zankel <chris@zankel.net>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
diff --git a/include/configs/xtfpga.h b/include/configs/xtfpga.h
new file mode 100644
index 0000000..c5b06e3
--- /dev/null
+++ b/include/configs/xtfpga.h
@@ -0,0 +1,268 @@
+/*
+ * Copyright (C) 2007-2013 Tensilica, Inc.
+ * Copyright (C) 2014 - 2016 Cadence Design Systems Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <asm/arch/core.h>
+#include <asm/addrspace.h>
+#include <asm/config.h>
+
+/*
+ * The 'xtfpga' board describes a set of very similar boards with only minimal
+ * differences.
+ */
+
+/*=====================*/
+/* Board and Processor */
+/*=====================*/
+
+#define CONFIG_XTFPGA
+
+/* FPGA CPU freq after init */
+#define CONFIG_SYS_CLK_FREQ (gd->cpu_clk)
+
+/*===================*/
+/* RAM Layout */
+/*===================*/
+
+#if XCHAL_HAVE_PTP_MMU
+#define CONFIG_SYS_MEMORY_BASE \
+ (XCHAL_VECBASE_RESET_VADDR - XCHAL_VECBASE_RESET_PADDR)
+#define CONFIG_SYS_IO_BASE 0xf0000000
+#else
+#define CONFIG_SYS_MEMORY_BASE 0x60000000
+#define CONFIG_SYS_IO_BASE 0x90000000
+#define CONFIG_MAX_MEM_MAPPED 0x10000000
+#endif
+
+/* Onboard RAM sizes:
+ *
+ * LX60 0x04000000 64 MB
+ * LX110 0x03000000 48 MB
+ * LX200 0x06000000 96 MB
+ * ML605 0x18000000 384 MB
+ * KC705 0x38000000 896 MB
+ *
+ * noMMU configurations can only see first 256MB of onboard memory.
+ */
+
+#if XCHAL_HAVE_PTP_MMU || CONFIG_BOARD_SDRAM_SIZE < 0x10000000
+#define CONFIG_SYS_SDRAM_SIZE CONFIG_BOARD_SDRAM_SIZE
+#else
+#define CONFIG_SYS_SDRAM_SIZE 0x10000000
+#endif
+
+#define CONFIG_SYS_SDRAM_BASE MEMADDR(0x00000000)
+
+/* Lx60 can only map 128kb memory (instead of 256kb) when running under OCD */
+#ifdef CONFIG_XTFPGA_LX60
+# define CONFIG_SYS_MONITOR_LEN 0x00020000 /* 128KB */
+#else
+# define CONFIG_SYS_MONITOR_LEN 0x00040000 /* 256KB */
+#endif
+
+#define CONFIG_SYS_STACKSIZE (512 << 10) /* stack 512KB */
+#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* heap 256KB */
+
+/* Linux boot param area in RAM (used only when booting linux) */
+#define CONFIG_SYS_BOOTPARAMS_LEN (64 << 10)
+
+/* Memory test is destructive so default must not overlap vectors or U-Boot*/
+#define CONFIG_SYS_MEMTEST_START MEMADDR(0x01000000)
+#define CONFIG_SYS_MEMTEST_END MEMADDR(0x02000000)
+
+/* Load address for stand-alone applications.
+ * MEMADDR cannot be used here, because the definition needs to be
+ * a plain number as it's used as -Ttext argument for ld in standalone
+ * example makefile.
+ * Handle noMMU vs MMUv2 vs MMUv3 distinction here manually.
+ */
+#if XCHAL_HAVE_PTP_MMU
+#if XCHAL_VECBASE_RESET_VADDR == XCHAL_VECBASE_RESET_PADDR
+#define CONFIG_STANDALONE_LOAD_ADDR 0x00800000
+#else
+#define CONFIG_STANDALONE_LOAD_ADDR 0xd0800000
+#endif
+#else
+#define CONFIG_STANDALONE_LOAD_ADDR 0x60800000
+#endif
+
+#if defined(CONFIG_MAX_MEM_MAPPED) && \
+ CONFIG_MAX_MEM_MAPPED < CONFIG_SYS_SDRAM_SIZE
+#define CONFIG_SYS_MEMORY_SIZE CONFIG_MAX_MEM_MAPPED
+#else
+#define CONFIG_SYS_MEMORY_SIZE CONFIG_SYS_SDRAM_SIZE
+#endif
+
+#define CONFIG_SYS_MEMORY_TOP MEMADDR(CONFIG_SYS_MEMORY_SIZE)
+#define CONFIG_SYS_TEXT_ADDR \
+ (CONFIG_SYS_MEMORY_TOP - CONFIG_SYS_MONITOR_LEN)
+
+/* Used by tftpboot; env var 'loadaddr' */
+#define CONFIG_SYS_LOAD_ADDR MEMADDR(0x02000000)
+
+/*==============================*/
+/* U-Boot general configuration */
+/*==============================*/
+
+#undef CONFIG_USE_IRQ /* Keep it simple, poll only */
+#define CONFIG_BOARD_POSTCLK_INIT
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_BOOTFILE "uImage"
+ /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 1024
+ /* Prt buf */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+ /* max number of command args */
+#define CONFIG_SYS_MAXARGS 16
+ /* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+
+/*=================*/
+/* U-Boot commands */
+/*=================*/
+
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_SAVES
+
+/*==============================*/
+/* U-Boot autoboot configuration */
+/*==============================*/
+
+#define CONFIG_BOOT_RETRY_TIME 60 /* retry after 60 secs */
+
+#define CONFIG_VERSION_VARIABLE
+#define CONFIG_AUTO_COMPLETE /* Support tab autocompletion */
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_CRC32_VERIFY
+#define CONFIG_MX_CYCLIC
+#define CONFIG_SHOW_BOOT_PROGRESS
+
+#ifdef DEBUG
+#define CONFIG_PANIC_HANG 1 /* Require manual reboot */
+#endif
+
+
+/*=========================================*/
+/* FPGA Registers (board info and control) */
+/*=========================================*/
+
+/*
+ * These assume FPGA bitstreams from Tensilica release RB and up. Earlier
+ * releases may not provide any/all of these registers or at these offsets.
+ * Some of the FPGA registers are broken down into bitfields described by
+ * SHIFT left amount and field WIDTH (bits), and also by a bitMASK.
+ */
+
+/* Date of FPGA bitstream build in binary coded decimal (BCD) */
+#define CONFIG_SYS_FPGAREG_DATE IOADDR(0x0D020000)
+#define FPGAREG_MTH_SHIFT 24 /* BCD month 1..12 */
+#define FPGAREG_MTH_WIDTH 8
+#define FPGAREG_MTH_MASK 0xFF000000
+#define FPGAREG_DAY_SHIFT 16 /* BCD day 1..31 */
+#define FPGAREG_DAY_WIDTH 8
+#define FPGAREG_DAY_MASK 0x00FF0000
+#define FPGAREG_YEAR_SHIFT 0 /* BCD year 2001..9999*/
+#define FPGAREG_YEAR_WIDTH 16
+#define FPGAREG_YEAR_MASK 0x0000FFFF
+
+/* FPGA core clock frequency in Hz (also input to UART) */
+#define CONFIG_SYS_FPGAREG_FREQ IOADDR(0x0D020004) /* CPU clock frequency*/
+
+/*
+ * DIP switch (left=sw1=lsb=bit0, right=sw8=msb=bit7; off=0, on=1):
+ * Bits 0..5 set the lower 6 bits of the default ethernet MAC.
+ * Bit 6 is reserved for future use by Tensilica.
+ * Bit 7 maps the first 128KB of ROM address space at CONFIG_SYS_ROM_BASE to
+ * the base of flash * (when on/1) or to the base of RAM (when off/0).
+ */
+#define CONFIG_SYS_FPGAREG_DIPSW IOADDR(0x0D02000C)
+#define FPGAREG_MAC_SHIFT 0 /* Ethernet MAC bits 0..5 */
+#define FPGAREG_MAC_WIDTH 6
+#define FPGAREG_MAC_MASK 0x3f
+#define FPGAREG_BOOT_SHIFT 7 /* Boot ROM addr mapping */
+#define FPGAREG_BOOT_WIDTH 1
+#define FPGAREG_BOOT_MASK 0x80
+#define FPGAREG_BOOT_RAM 0
+#define FPGAREG_BOOT_FLASH (1<<FPGAREG_BOOT_SHIFT)
+
+/* Force hard reset of board by writing a code to this register */
+#define CONFIG_SYS_FPGAREG_RESET IOADDR(0x0D020010) /* Reset board .. */
+#define CONFIG_SYS_FPGAREG_RESET_CODE 0x0000DEAD /* by writing this code */
+
+/*====================*/
+/* Serial Driver Info */
+/*====================*/
+
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_COM1 IOADDR(0x0D050020) /* Base address */
+
+/* Input clk to NS16550 (in Hz; the SYS_CLK_FREQ is in kHz) */
+#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_CLK_FREQ
+#define CONFIG_CONS_INDEX 1 /* use UART0 for console */
+#define CONFIG_BAUDRATE 115200 /* Default baud rate */
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*======================*/
+/* Ethernet Driver Info */
+/*======================*/
+
+#define CONFIG_ETHBASE 00:50:C2:13:6f:00
+#define CONFIG_SYS_ETHOC_BASE IOADDR(0x0d030000)
+#define CONFIG_SYS_ETHOC_BUFFER_ADDR IOADDR(0x0D800000)
+
+/*=====================*/
+/* Flash & Environment */
+/*=====================*/
+
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER /* use generic CFI driver */
+#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+#ifdef CONFIG_XTFPGA_LX60
+# define CONFIG_SYS_FLASH_SIZE 0x0040000 /* 4MB */
+# define CONFIG_SYS_FLASH_SECT_SZ 0x10000 /* block size 64KB */
+# define CONFIG_SYS_FLASH_PARMSECT_SZ 0x2000 /* param size 8KB */
+# define CONFIG_SYS_FLASH_BASE IOADDR(0x08000000)
+# define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#elif defined(CONFIG_XTFPGA_KC705)
+# define CONFIG_SYS_FLASH_SIZE 0x8000000 /* 128MB */
+# define CONFIG_SYS_FLASH_SECT_SZ 0x20000 /* block size 128KB */
+# define CONFIG_SYS_FLASH_PARMSECT_SZ 0x8000 /* param size 32KB */
+# define CONFIG_SYS_FLASH_BASE IOADDR(0x00000000)
+# define CONFIG_SYS_MONITOR_BASE IOADDR(0x06000000)
+#else
+# define CONFIG_SYS_FLASH_SIZE 0x1000000 /* 16MB */
+# define CONFIG_SYS_FLASH_SECT_SZ 0x20000 /* block size 128KB */
+# define CONFIG_SYS_FLASH_PARMSECT_SZ 0x8000 /* param size 32KB */
+# define CONFIG_SYS_FLASH_BASE IOADDR(0x08000000)
+# define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#endif
+#define CONFIG_SYS_MAX_FLASH_SECT \
+ (CONFIG_SYS_FLASH_SECT_SZ/CONFIG_SYS_FLASH_PARMSECT_SZ + \
+ CONFIG_SYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ - 1)
+#define CONFIG_SYS_FLASH_PROTECTION /* hw flash protection */
+
+/*
+ * Put environment in top block (64kB)
+ * Another option would be to put env. in 2nd param block offs 8KB, size 8KB
+ */
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_OFFSET (CONFIG_SYS_FLASH_SIZE - CONFIG_SYS_FLASH_SECT_SZ)
+#define CONFIG_ENV_SIZE CONFIG_SYS_FLASH_SECT_SZ
+
+/* print 'E' for empty sector on flinfo */
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+
+#endif /* __CONFIG_H */