[PPC440SPe] Improve PCIe configuration space access
- correct configuration space mapping
- correct bus numbering
- better access to config space
Prior to this patch, the 440SPe host/PCIe bridge was able to configure only the
first device on the first bus. We now allow to configure up to 16 buses;
also, scanning for devices behind the PCIe-PCIe bridge is supported, so
peripheral devices farther in hierarchy can be identified.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
diff --git a/board/amcc/katmai/init.S b/board/amcc/katmai/init.S
index 5202ae6..e3f3da6 100644
--- a/board/amcc/katmai/init.S
+++ b/board/amcc/katmai/init.S
@@ -67,9 +67,9 @@
tlbentry(CFG_PCIE_MEMBASE, SZ_256M, 0xB0000000, 0xD, AC_R|AC_W|SA_G|SA_I)
tlbentry(CFG_PCIE_BASE, SZ_16K, 0x20000000, 0xC, AC_R|AC_W|SA_G|SA_I)
- tlbentry(CFG_PCIE0_CFGBASE, SZ_1K, 0x40000000, 0xC, AC_R|AC_W|SA_G|SA_I)
- tlbentry(CFG_PCIE1_CFGBASE, SZ_1K, 0x80000000, 0xC, AC_R|AC_W|SA_G|SA_I)
- tlbentry(CFG_PCIE2_CFGBASE, SZ_1K, 0xC0000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE0_CFGBASE, SZ_16M, 0x40000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE1_CFGBASE, SZ_16M, 0x80000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE2_CFGBASE, SZ_16M, 0xC0000000, 0xC, AC_R|AC_W|SA_G|SA_I)
tlbentry(CFG_PCIE0_XCFGBASE, SZ_1K, 0x50000000, 0xC, AC_R|AC_W|SA_G|SA_I)
tlbentry(CFG_PCIE1_XCFGBASE, SZ_1K, 0x90000000, 0xC, AC_R|AC_W|SA_G|SA_I)
tlbentry(CFG_PCIE2_XCFGBASE, SZ_1K, 0xD0000000, 0xC, AC_R|AC_W|SA_G|SA_I)
@@ -109,9 +109,9 @@
tlbentry(CFG_PCI_MEMBASE, SZ_256M, 0x10000000, 0xC, AC_R|AC_W|SA_G|SA_I)
tlbentry(CFG_PCIE_MEMBASE, SZ_256M, 0xB0000000, 0xD, AC_R|AC_W|SA_G|SA_I)
- tlbentry(CFG_PCIE0_CFGBASE, SZ_1K, 0x00100000, 0xD, AC_R|AC_W|SA_G|SA_I)
- tlbentry(CFG_PCIE1_CFGBASE, SZ_1K, 0x20100000, 0xD, AC_R|AC_W|SA_G|SA_I)
- tlbentry(CFG_PCIE2_CFGBASE, SZ_1K, 0x40100000, 0xD, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE0_CFGBASE, SZ_16M, 0x00000000, 0xD, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE1_CFGBASE, SZ_16M, 0x20000000, 0xD, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CFG_PCIE2_CFGBASE, SZ_16M, 0x40000000, 0xD, AC_R|AC_W|SA_G|SA_I)
tlbentry(CFG_PCIE0_XCFGBASE, SZ_1K, 0x10000000, 0xD, AC_R|AC_W|SA_G|SA_I)
tlbentry(CFG_PCIE1_XCFGBASE, SZ_1K, 0x30000000, 0xD, AC_R|AC_W|SA_G|SA_I)
tlbentry(CFG_PCIE2_XCFGBASE, SZ_1K, 0x50000000, 0xD, AC_R|AC_W|SA_G|SA_I)
diff --git a/board/amcc/katmai/katmai.c b/board/amcc/katmai/katmai.c
index b804d55..a9ae4a3 100644
--- a/board/amcc/katmai/katmai.c
+++ b/board/amcc/katmai/katmai.c
@@ -392,7 +392,7 @@
static struct pci_controller pcie_hose[3] = {{0},{0},{0}};
-void pcie_setup_hoses(void)
+void pcie_setup_hoses(int busno)
{
struct pci_controller *hose;
int i, bus;
@@ -401,7 +401,7 @@
* assume we're called after the PCIX hose is initialized, which takes
* bus ID 0 and therefore start numbering PCIe's from 1.
*/
- bus = 1;
+ bus = busno;
for (i = 0; i <= 2; i++) {
/* Check for katmai card presence */
if (!katmai_pcie_card_present(i))
@@ -418,8 +418,8 @@
hose = &pcie_hose[i];
hose->first_busno = bus;
- hose->last_busno = bus;
- bus++;
+ hose->last_busno = bus;
+ hose->current_busno = bus;
/* setup mem resource */
pci_set_region(hose->regions + 0,
@@ -443,6 +443,7 @@
* Config access can only go down stream
*/
hose->last_busno = pci_hose_scan(hose);
+ bus = hose->last_busno + 1;
#endif
}
}