sunxi: dts: arm64: update devicetree files
Update the devicetree files from the Linux kernel, version v6.0-rc4.
This is covering the 64-bit SoCs, from arch/arm64/boot/dts/allwinner.
This avoids the not backwards-compatible r_intc binding change, to allow
older kernels to boot, but the other nodes are updated.
Not much change here, the vast majority is actually cosmetic: node names
and using symbolic names for the the RTC clocks.
Some A64 boards gain some audio nodes.
The H616 DTs are now switched to the version finally merged into the
kernel, which brings some changes, but none affecting U-Boot.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
diff --git a/arch/arm/dts/sun50i-h616.dtsi b/arch/arm/dts/sun50i-h616.dtsi
index 2f71e85..622a1f7 100644
--- a/arch/arm/dts/sun50i-h616.dtsi
+++ b/arch/arm/dts/sun50i-h616.dtsi
@@ -6,6 +6,7 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/sun50i-h616-ccu.h>
#include <dt-bindings/clock/sun50i-h6-r-ccu.h>
+#include <dt-bindings/clock/sun6i-rtc.h>
#include <dt-bindings/reset/sun50i-h616-ccu.h>
#include <dt-bindings/reset/sun50i-h6-r-ccu.h>
@@ -51,7 +52,23 @@
};
};
- osc24M: osc24M_clk {
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ /*
+ * 256 KiB reserved for Trusted Firmware-A (BL31).
+ * This is added by BL31 itself, but some bootloaders fail
+ * to propagate this into the DTB handed to kernels.
+ */
+ secmon@40000000 {
+ reg = <0x0 0x40000000 0x0 0x40000>;
+ no-map;
+ };
+ };
+
+ osc24M: osc24M-clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
@@ -110,7 +127,7 @@
ccu: clock@3001000 {
compatible = "allwinner,sun50i-h616-ccu";
reg = <0x03001000 0x1000>;
- clocks = <&osc24M>, <&rtc 0>, <&rtc 2>;
+ clocks = <&osc24M>, <&rtc CLK_OSC32K>, <&rtc CLK_IOSC>;
clock-names = "hosc", "losc", "iosc";
#clock-cells = <1>;
#reset-cells = <1>;
@@ -135,7 +152,7 @@
<GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_APB1>, <&osc24M>, <&rtc 0>;
+ clocks = <&ccu CLK_APB1>, <&osc24M>, <&rtc CLK_OSC32K>;
clock-names = "apb", "hosc", "losc";
gpio-controller;
#gpio-cells = <3>;
@@ -161,7 +178,7 @@
function = "i2c3";
};
- ir_rx_pin: ir_rx_pin {
+ ir_rx_pin: ir-rx-pin {
pins = "PH10";
function = "ir_rx";
};
@@ -174,6 +191,7 @@
bias-pull-up;
};
+ /omit-if-no-ref/
mmc1_pins: mmc1-pins {
pins = "PG0", "PG1", "PG2", "PG3",
"PG4", "PG5";
@@ -191,17 +209,26 @@
bias-pull-up;
};
+ /omit-if-no-ref/
spi0_pins: spi0-pins {
- pins = "PC0", "PC2", "PC3", "PC4";
+ pins = "PC0", "PC2", "PC4";
function = "spi0";
};
+ /omit-if-no-ref/
+ spi0_cs0_pin: spi0-cs0-pin {
+ pins = "PC3";
+ function = "spi0";
+ };
+
+ /omit-if-no-ref/
spi1_pins: spi1-pins {
pins = "PH6", "PH7", "PH8";
function = "spi1";
};
- spi1_cs_pin: spi1-cs-pin {
+ /omit-if-no-ref/
+ spi1_cs0_pin: spi1-cs0-pin {
pins = "PH5";
function = "spi1";
};
@@ -211,11 +238,13 @@
function = "uart0";
};
+ /omit-if-no-ref/
uart1_pins: uart1-pins {
pins = "PG6", "PG7";
function = "uart1";
};
+ /omit-if-no-ref/
uart1_rts_cts_pins: uart1-rts-cts-pins {
pins = "PG8", "PG9";
function = "uart1";
@@ -245,10 +274,10 @@
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
status = "disabled";
+ max-frequency = <150000000>;
cap-sd-highspeed;
cap-mmc-highspeed;
mmc-ddr-3_3v;
- mmc-ddr-1_8v;
cap-sdio-irq;
#address-cells = <1>;
#size-cells = <0>;
@@ -266,10 +295,10 @@
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>;
status = "disabled";
+ max-frequency = <150000000>;
cap-sd-highspeed;
cap-mmc-highspeed;
mmc-ddr-3_3v;
- mmc-ddr-1_8v;
cap-sdio-irq;
#address-cells = <1>;
#size-cells = <0>;
@@ -287,10 +316,10 @@
pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins>;
status = "disabled";
+ max-frequency = <150000000>;
cap-sd-highspeed;
cap-mmc-highspeed;
mmc-ddr-3_3v;
- mmc-ddr-1_8v;
cap-sdio-irq;
#address-cells = <1>;
#size-cells = <0>;
@@ -364,6 +393,7 @@
i2c0: i2c@5002000 {
compatible = "allwinner,sun50i-h616-i2c",
+ "allwinner,sun8i-v536-i2c",
"allwinner,sun6i-a31-i2c";
reg = <0x05002000 0x400>;
interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
@@ -378,6 +408,7 @@
i2c1: i2c@5002400 {
compatible = "allwinner,sun50i-h616-i2c",
+ "allwinner,sun8i-v536-i2c",
"allwinner,sun6i-a31-i2c";
reg = <0x05002400 0x400>;
interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
@@ -390,6 +421,7 @@
i2c2: i2c@5002800 {
compatible = "allwinner,sun50i-h616-i2c",
+ "allwinner,sun8i-v536-i2c",
"allwinner,sun6i-a31-i2c";
reg = <0x05002800 0x400>;
interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
@@ -402,6 +434,7 @@
i2c3: i2c@5002c00 {
compatible = "allwinner,sun50i-h616-i2c",
+ "allwinner,sun8i-v536-i2c",
"allwinner,sun6i-a31-i2c";
reg = <0x05002c00 0x400>;
interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
@@ -414,6 +447,7 @@
i2c4: i2c@5003000 {
compatible = "allwinner,sun50i-h616-i2c",
+ "allwinner,sun8i-v536-i2c",
"allwinner,sun6i-a31-i2c";
reg = <0x05003000 0x400>;
interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
@@ -432,8 +466,6 @@
clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
clock-names = "ahb", "mod";
resets = <&ccu RST_BUS_SPI0>;
- pinctrl-names = "default";
- pinctrl-0 = <&spi0_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
@@ -447,24 +479,22 @@
clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
clock-names = "ahb", "mod";
resets = <&ccu RST_BUS_SPI1>;
- pinctrl-names = "default";
- pinctrl-0 = <&spi1_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
emac0: ethernet@5020000 {
- compatible = "allwinner,sun50i-h616-emac",
+ compatible = "allwinner,sun50i-h616-emac0",
"allwinner,sun50i-a64-emac";
- syscon = <&syscon>;
reg = <0x05020000 0x10000>;
interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "macirq";
- resets = <&ccu RST_BUS_EMAC0>;
- reset-names = "stmmaceth";
clocks = <&ccu CLK_BUS_EMAC0>;
clock-names = "stmmaceth";
+ resets = <&ccu RST_BUS_EMAC0>;
+ reset-names = "stmmaceth";
+ syscon = <&syscon>;
status = "disabled";
mdio0: mdio {
@@ -474,197 +504,21 @@
};
};
- emac1: ethernet@5030000 {
- compatible = "allwinner,sun50i-h616-emac";
- syscon = <&syscon 1>;
- reg = <0x05030000 0x10000>;
- interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "macirq";
- resets = <&ccu RST_BUS_EMAC1>;
- reset-names = "stmmaceth";
- clocks = <&ccu CLK_BUS_EMAC1>;
- clock-names = "stmmaceth";
- status = "disabled";
-
- mdio1: mdio {
- compatible = "snps,dwmac-mdio";
- #address-cells = <1>;
- #size-cells = <0>;
- };
- };
-
- usbotg: usb@5100000 {
- compatible = "allwinner,sun50i-h616-musb",
- "allwinner,sun8i-h3-musb";
- reg = <0x05100000 0x0400>;
- clocks = <&ccu CLK_BUS_OTG>;
- resets = <&ccu RST_BUS_OTG>;
- interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "mc";
- phys = <&usbphy 0>;
- phy-names = "usb";
- extcon = <&usbphy 0>;
- status = "disabled";
- };
-
- usbphy: phy@5100400 {
- compatible = "allwinner,sun50i-h616-usb-phy";
- reg = <0x05100400 0x24>,
- <0x05101800 0x14>,
- <0x05200800 0x14>,
- <0x05310800 0x14>,
- <0x05311800 0x14>;
- reg-names = "phy_ctrl",
- "pmu0",
- "pmu1",
- "pmu2",
- "pmu3";
- clocks = <&ccu CLK_USB_PHY0>,
- <&ccu CLK_USB_PHY1>,
- <&ccu CLK_USB_PHY2>,
- <&ccu CLK_USB_PHY3>;
- clock-names = "usb0_phy",
- "usb1_phy",
- "usb2_phy",
- "usb3_phy";
- resets = <&ccu RST_USB_PHY0>,
- <&ccu RST_USB_PHY1>,
- <&ccu RST_USB_PHY2>,
- <&ccu RST_USB_PHY3>;
- reset-names = "usb0_reset",
- "usb1_reset",
- "usb2_reset",
- "usb3_reset";
- status = "disabled";
- #phy-cells = <1>;
- };
-
- ehci0: usb@5101000 {
- compatible = "allwinner,sun50i-h616-ehci",
- "generic-ehci";
- reg = <0x05101000 0x100>;
- interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_OHCI0>,
- <&ccu CLK_BUS_EHCI0>,
- <&ccu CLK_USB_OHCI0>;
- resets = <&ccu RST_BUS_OHCI0>,
- <&ccu RST_BUS_EHCI0>;
- phys = <&usbphy 0>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci0: usb@5101400 {
- compatible = "allwinner,sun50i-h616-ohci",
- "generic-ohci";
- reg = <0x05101400 0x100>;
- interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_OHCI0>,
- <&ccu CLK_USB_OHCI0>;
- resets = <&ccu RST_BUS_OHCI0>;
- phys = <&usbphy 0>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci1: usb@5200000 {
- compatible = "allwinner,sun50i-h616-ehci",
- "generic-ehci";
- reg = <0x05200000 0x100>;
- interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_OHCI1>,
- <&ccu CLK_BUS_EHCI1>,
- <&ccu CLK_USB_OHCI1>;
- resets = <&ccu RST_BUS_OHCI1>,
- <&ccu RST_BUS_EHCI1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci1: usb@5200400 {
- compatible = "allwinner,sun50i-h616-ohci",
- "generic-ohci";
- reg = <0x05200400 0x100>;
- interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_OHCI1>,
- <&ccu CLK_USB_OHCI1>;
- resets = <&ccu RST_BUS_OHCI1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci2: usb@5310000 {
- compatible = "allwinner,sun50i-h616-ehci",
- "generic-ehci";
- reg = <0x05310000 0x100>;
- interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_OHCI2>,
- <&ccu CLK_BUS_EHCI2>,
- <&ccu CLK_USB_OHCI2>;
- resets = <&ccu RST_BUS_OHCI2>,
- <&ccu RST_BUS_EHCI2>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci2: usb@5310400 {
- compatible = "allwinner,sun50i-h616-ohci",
- "generic-ohci";
- reg = <0x05310400 0x100>;
- interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_OHCI2>,
- <&ccu CLK_USB_OHCI2>;
- resets = <&ccu RST_BUS_OHCI2>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci3: usb@5311000 {
- compatible = "allwinner,sun50i-h616-ehci",
- "generic-ehci";
- reg = <0x05311000 0x100>;
- interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_OHCI3>,
- <&ccu CLK_BUS_EHCI3>,
- <&ccu CLK_USB_OHCI3>;
- resets = <&ccu RST_BUS_OHCI3>,
- <&ccu RST_BUS_EHCI3>;
- phys = <&usbphy 3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci3: usb@5311400 {
- compatible = "allwinner,sun50i-h616-ohci",
- "generic-ohci";
- reg = <0x05311400 0x100>;
- interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_OHCI3>,
- <&ccu CLK_USB_OHCI3>;
- resets = <&ccu RST_BUS_OHCI3>;
- phys = <&usbphy 3>;
- phy-names = "usb";
- status = "disabled";
- };
-
rtc: rtc@7000000 {
- compatible = "allwinner,sun50i-h616-rtc",
- "allwinner,sun50i-h6-rtc";
+ compatible = "allwinner,sun50i-h616-rtc";
reg = <0x07000000 0x400>;
- interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
- clock-output-names = "osc32k", "osc32k-out", "iosc";
+ interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&r_ccu CLK_R_APB1_RTC>, <&osc24M>,
+ <&ccu CLK_PLL_SYSTEM_32K>;
+ clock-names = "bus", "hosc",
+ "pll-32k";
#clock-cells = <1>;
};
r_ccu: clock@7010000 {
compatible = "allwinner,sun50i-h616-r-ccu";
- reg = <0x07010000 0x400>;
- clocks = <&osc24M>, <&rtc 0>, <&rtc 2>,
+ reg = <0x07010000 0x210>;
+ clocks = <&osc24M>, <&rtc CLK_OSC32K>, <&rtc CLK_IOSC>,
<&ccu CLK_PLL_PERIPH0>;
clock-names = "hosc", "losc", "iosc", "pll-periph";
#clock-cells = <1>;
@@ -674,14 +528,13 @@
r_pio: pinctrl@7022000 {
compatible = "allwinner,sun50i-h616-r-pinctrl";
reg = <0x07022000 0x400>;
- interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&r_ccu CLK_R_APB1>, <&osc24M>, <&rtc 0>;
+ clocks = <&r_ccu CLK_R_APB1>, <&osc24M>,
+ <&rtc CLK_OSC32K>;
clock-names = "apb", "hosc", "losc";
gpio-controller;
#gpio-cells = <3>;
- interrupt-controller;
- #interrupt-cells = <3>;
+ /omit-if-no-ref/
r_i2c_pins: r-i2c-pins {
pins = "PL0", "PL1";
function = "s_i2c";
@@ -694,21 +547,22 @@
};
ir: ir@7040000 {
- compatible = "allwinner,sun50i-h616-ir",
- "allwinner,sun6i-a31-ir";
- reg = <0x07040000 0x400>;
- interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&r_ccu CLK_R_APB1_IR>,
- <&r_ccu CLK_IR>;
- clock-names = "apb", "ir";
- resets = <&r_ccu RST_R_APB1_IR>;
- pinctrl-names = "default";
- pinctrl-0 = <&ir_rx_pin>;
- status = "disabled";
+ compatible = "allwinner,sun50i-h616-ir",
+ "allwinner,sun6i-a31-ir";
+ reg = <0x07040000 0x400>;
+ interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&r_ccu CLK_R_APB1_IR>,
+ <&r_ccu CLK_IR>;
+ clock-names = "apb", "ir";
+ resets = <&r_ccu RST_R_APB1_IR>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_rx_pin>;
+ status = "disabled";
};
r_i2c: i2c@7081400 {
compatible = "allwinner,sun50i-h616-i2c",
+ "allwinner,sun8i-v536-i2c",
"allwinner,sun6i-a31-i2c";
reg = <0x07081400 0x400>;
interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;