Merge branch 'mpc86xx'
diff --git a/CHANGELOG b/CHANGELOG
index c479e5d..0a52639 100644
--- a/CHANGELOG
+++ b/CHANGELOG
@@ -2,8 +2,48 @@
Changes since U-Boot 1.1.4:
======================================================================
+* Fix watchdog issues for ColdFire boards.
+
+* Add M5271EVB board support.
+
+* Make R5200 specific low level initialization board conditional.
+
+* Update CPU target identification strings for ColdFire family.
+
+* Update register definitions for MCF5271.
+
+* Fix serial console support for MCF5271.
+
+* Fixes for gcc 3.4 based m68k toolchain,
+ based on patch by Jate Sujjavanich.
+
+* Fix lowboot support on MCC200 board
+
+* Merged MPC8349ADS and MPC8349EMDS ports into MPC8349EMDS port:
+ - Removed MPC8349ADS port
+ - Added PCI support to MPC8349ADS
+ - reworked memory map to allow mapping of all regions with BATs
+ Patch by Kumar Gala, 20 Apr 2006
+
+* Coding Style cleanup
+
+* Write RTC seconds first to maintain settings integrity per
+ Maxim/Dallas DS1306 data sheet.
+ Patch by Alan J. Luse, 02 May 2006
+
+* Scheduled for removal: strnicmp() which is unused
+
+* Update for Intel Monahans boards:
+ - support for magic key detection and handling on delta board
+ - NAND support for zylonite board + some minor cleanup
+
+* Declare load_serial_ymodem() when using CFG_CMD_LOADB.
+ Patch by Jon Loeliger, 01 May 2006
+
+* Fixed handling of bad checksums with "mkimage -l"
+
* Added support for BC3450 board
- Patch by Stefan Strobl, 21. Oct 2005
+ Patch by Stefan Strobl, 21 Oct 2005
* Update for NC650 board:
- Support rev1 and rev2 hardware
@@ -469,6 +509,15 @@
PMC405 and CPCI2DP: Added firmware download and booting via pci.
Patch by Matthias Fuchs, 20 Dec 2005
+* Add ColdFire targets to MAKEALL script
+ Patch by Zachary Landau, 26 Jan 2006
+
+* Add support for r5200 board
+ Patch by Zachary Landau, 26 Jan 2006
+
+* Add support for Freescale M5271 processor
+ Patch by Zachary Landau, 26 Jan 2006
+
* Fix 28F256J3A support on PM520 board
(without bank-switching only 32 MB can be accessed)
@@ -1766,7 +1815,7 @@
- use -mtune=xscale and -march=armv5 options for PXA
* Patch by Florian Schlote, 08 Sep 2004:
- Add support for SenTec-COBRA5272-board (Coldfire).
+ Add support for SenTec-COBRA5272-board (ColdFire).
* Patch by Gleb Natapov, 07 Sep 2004:
mpc824x: set PCI latency timer to a sane value
@@ -1824,7 +1873,7 @@
* Patch by Stefan Roese, 16 Dez 2004:
- ext2fs support added
- Tundra universe support added
- - Coldfire MCF5249 support added (no preloader needed!)
+ - ColdFire MCF5249 support added (no preloader needed!)
- MCF5249 board TASREG added
- PPC boards added: APC405, CPCI405DT, CPCI750, G2000, HH405,
VOM405, WUH405
@@ -2146,7 +2195,7 @@
* Fix NSCU config; add ethernet wakeup code.
-* Add link for preloader for Motorola Coldfire to README.m68k
+* Add link for preloader for Motorola ColdFire to README.m68k
* Patch by Michael Bendzick, 12 Jul 2004:
fix output formatting in drivers/cfi_flash.c
@@ -3093,7 +3142,7 @@
* Some code cleanup
* Patch by Josef Baumgartner, 10 Feb 2004:
- Fixes for Coldfire port
+ Fixes for ColdFire port
* Patch by Brad Kemp, 11 Feb 2004:
Fix CFI flash driver problems
@@ -3359,7 +3408,7 @@
- 4xx: removed spurious MII error messages on "mii info" command.
* Patch by Bernhard Kuhn, 28 Nov 2003:
- add support for Coldfire CPU
+ add support for ColdFire CPU
add support for Motorola M5272C3 and M5282EVB boards
* Patch by Pierre Aubert, 24 Nov 2003:
diff --git a/MAINTAINERS b/MAINTAINERS
index 0ef9e03..9380220 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -534,6 +534,10 @@
TASREG MCF5249
+Zachary P. Landau <zachary.landau@labxtechnologies.com>
+
+ r5200 mcf52x2
+
#########################################################################
# End of MAINTAINERS list #
#########################################################################
diff --git a/MAKEALL b/MAKEALL
index 6e620dd..8ab31e0 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -117,7 +117,7 @@
#########################################################################
LIST_83xx=" \
- MPC8349ADS TQM834x MPC8349EMDS \
+ TQM834x MPC8349EMDS \
"
@@ -273,6 +273,12 @@
LIST_microblaze="suzaku"
+#########################################################################
+## ColdFire Systems
+#########################################################################
+
+LIST_coldfire="cobra5272 M5272C3 M5282EVB TASREG r5200 M5271EVB"
+
#-----------------------------------------------------------------------
#----- for now, just run PPC by default -----
@@ -300,7 +306,8 @@
microblaze| \
mips|mips_el| \
nios|nios2| \
- x86|I486)
+ x86|I486| \
+ coldfire)
for target in `eval echo '$LIST_'${arg}`
do
build_target ${target}
diff --git a/Makefile b/Makefile
index acfa5bd..a33a8be 100644
--- a/Makefile
+++ b/Makefile
@@ -329,7 +329,7 @@
mcc200_lowboot_config: unconfig
@ >include/config.h
@[ -z "$(findstring lowboot_,$@)" ] || \
- { echo "TEXT_BASE = 0xFE000000" >board/mcc200/config.tmp ; \
+ { echo "TEXT_BASE = 0xFC000000" >board/mcc200/config.tmp ; \
echo "... with lowboot configuration" ; \
}
@./mkconfig mcc200 ppc mpc5xxx mcc200
@@ -1318,6 +1318,12 @@
TASREG_config : unconfig
@./mkconfig $(@:_config=) m68k mcf52x2 tasreg esd
+r5200_config : unconfig
+ @./mkconfig $(@:_config=) m68k mcf52x2 r5200
+
+M5271EVB_config : unconfig
+ @./mkconfig $(@:_config=) m68k mcf52x2 m5271evb
+
#########################################################################
## MPC83xx Systems
#########################################################################
diff --git a/board/bc3450/bc3450.c b/board/bc3450/bc3450.c
index a030b82..0d86518 100644
--- a/board/bc3450/bc3450.c
+++ b/board/bc3450/bc3450.c
@@ -1,6 +1,4 @@
/*
- * -- Version 1.1 --
- *
* (C) Copyright 2003-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
@@ -13,9 +11,6 @@
* (C) Copyright 2006
* Stefan Strobl, GERSYS GmbH, stefan.strobl@gersys.de
*
- * History:
- * 1.1 - improved SM501 init to meet spec timing
- *
* See file CREDITS for list of people who contributed to this
* project.
*
@@ -51,7 +46,7 @@
#ifdef CONFIG_RTC_MPC5200
#include <rtc.h>
-#endif
+#endif
#ifdef CONFIG_PS2MULT
void ps2mult_early_init(void);
@@ -375,7 +370,7 @@
int board_early_init_r (void)
{
#ifdef CONFIG_RTC_MPC5200
- struct rtc_time t;
+ struct rtc_time t;
/* set to Wed Dec 31 19:00:00 1969 */
t.tm_sec = t.tm_min = 0;
@@ -384,7 +379,7 @@
t.tm_mon = 12;
t.tm_year = 1969;
t.tm_wday = 3;
-
+
rtc_set(&t);
#endif /* CONFIG_RTC_MPC5200 */
@@ -482,7 +477,7 @@
} else {
puts ("VGA: SMI501 (Voyager) with 8 MB\n");
}
- /* restore origianl FB content */
+ /* restore origianl FB content */
if (restore) {
*(volatile u16 *)CFG_CS1_START = save;
__asm__ volatile ("sync");
@@ -493,8 +488,8 @@
#ifdef CONFIG_VIDEO_SM501
-#define DISPLAY_WIDTH 640
-#define DISPLAY_HEIGHT 480
+#define DISPLAY_WIDTH 640
+#define DISPLAY_HEIGHT 480
#ifdef CONFIG_VIDEO_SM501_8BPP
#error CONFIG_VIDEO_SM501_8BPP not supported.
@@ -633,7 +628,7 @@
} else {
ret = SM501_MMIO_BASE;
}
-
+
if (restore) {
*(volatile u16 *)CFG_CS1_START = save;
__asm__ volatile ("sync");
diff --git a/board/bc3450/cmd_bc3450.c b/board/bc3450/cmd_bc3450.c
index 1442b68..6bbe4e6 100644
--- a/board/bc3450/cmd_bc3450.c
+++ b/board/bc3450/cmd_bc3450.c
@@ -27,7 +27,7 @@
#include <common.h>
#include <command.h>
-/*
+/*
* BC3450 specific commands
*/
#if (CONFIG_COMMANDS & CFG_CMD_BSP)
@@ -39,7 +39,7 @@
# define dprintf(fmt,args...)
#endif
-/*
+/*
* Definitions for DS1620 chip
*/
#define THERM_START_CONVERT 0xee
@@ -57,8 +57,8 @@
#define CFG_STANDALONE 0
struct therm {
- int hi;
- int lo;
+ int hi;
+ int lo;
};
/*
@@ -124,36 +124,46 @@
* Yet, the initialisation sequence is executed only the first
* time the function is called.
*/
-int sm501_gpio_init(void)
+int sm501_gpio_init (void)
{
- static int init_done = 0;
+ static int init_done = 0;
- if(init_done) {
+ if (init_done) {
/* dprintf("sm501_gpio_init: nothing to be done.\n"); */
- return 1;
- }
+ return 1;
+ }
- /* enable SM501 GPIO control (in both power modes) */
- *(vu_long *) (SM501_MMIO_BASE + SM501_POWER_MODE0_GATE) |= POWER_MODE_GATE_GPIO_PWM_I2C;
- *(vu_long *) (SM501_MMIO_BASE + SM501_POWER_MODE1_GATE) |= POWER_MODE_GATE_GPIO_PWM_I2C;
+ /* enable SM501 GPIO control (in both power modes) */
+ *(vu_long *) (SM501_MMIO_BASE + SM501_POWER_MODE0_GATE) |=
+ POWER_MODE_GATE_GPIO_PWM_I2C;
+ *(vu_long *) (SM501_MMIO_BASE + SM501_POWER_MODE1_GATE) |=
+ POWER_MODE_GATE_GPIO_PWM_I2C;
- /* set up default O/Ps */
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) &= ~(DS1620_RES | DS1620_CLK);
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) |= DS1620_DQ;
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_HIGH) &= ~(FP_DATA_TRI);
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_HIGH) |= (BUZZER | PWR_OFF);
+ /* set up default O/Ps */
+ *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) &=
+ ~(DS1620_RES | DS1620_CLK);
+ *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) |= DS1620_DQ;
+ *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_HIGH) &=
+ ~(FP_DATA_TRI);
+ *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_HIGH) |=
+ (BUZZER | PWR_OFF);
- /* configure directions for SM501 GPIO pins */
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_CTRL_LOW) &= ~(0xFF << 24);
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_CTRL_HIGH) &= ~(0x3F << 14);
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_DIR_LOW) &= ~(DIP | DS1620_DQ);
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_DIR_LOW) |= (DS1620_RES | DS1620_CLK);
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_DIR_HIGH) &= ~DS1620_TLOW;
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_DIR_HIGH) |= (PWR_OFF | BUZZER | FP_DATA_TRI);
+ /* configure directions for SM501 GPIO pins */
+ *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_CTRL_LOW) &= ~(0xFF << 24);
+ *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_CTRL_HIGH) &=
+ ~(0x3F << 14);
+ *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_DIR_LOW) &=
+ ~(DIP | DS1620_DQ);
+ *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_DIR_LOW) |=
+ (DS1620_RES | DS1620_CLK);
+ *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_DIR_HIGH) &=
+ ~DS1620_TLOW;
+ *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_DIR_HIGH) |=
+ (PWR_OFF | BUZZER | FP_DATA_TRI);
- init_done = 1;
+ init_done = 1;
/* dprintf("sm501_gpio_init: done.\n"); */
- return 0;
+ return 0;
}
@@ -163,347 +173,358 @@
* read and prints the dip switch
* and/or external config inputs (4bits) 0...0x0F
*/
-int cmd_dip (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+int cmd_dip (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
{
- vu_long rc = 0;
+ vu_long rc = 0;
- sm501_gpio_init();
+ sm501_gpio_init ();
- /* read dip switch */
- rc = *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW);
- rc = ~rc;
- rc &= DIP;
- rc = (int)(rc >> 24);
+ /* read dip switch */
+ rc = *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW);
+ rc = ~rc;
+ rc &= DIP;
+ rc = (int) (rc >> 24);
- /* plausibility check */
- if (rc > 0x0F)
- return -1;
+ /* plausibility check */
+ if (rc > 0x0F)
+ return -1;
- printf ("0x%x\n", rc);
- return 0;
+ printf ("0x%x\n", rc);
+ return 0;
}
-U_BOOT_CMD(
- dip , 1, 1, cmd_dip,
- "dip - read dip switch and config inputs\n",
- "\n"
- " - prints the state of the dip switch and/or\n"
- " external configuration inputs as hex value.\n"
- " - \"Config 1\" is the LSB\n"
- );
+U_BOOT_CMD (dip, 1, 1, cmd_dip,
+ "dip - read dip switch and config inputs\n",
+ "\n"
+ " - prints the state of the dip switch and/or\n"
+ " external configuration inputs as hex value.\n"
+ " - \"Config 1\" is the LSB\n");
/*
* buz - turns Buzzer on/off
*/
#ifdef CONFIG_BC3450_BUZZER
-static int cmd_buz (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+static int cmd_buz (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
{
- if (argc != 2) {
+ if (argc != 2) {
+ printf ("Usage:\nspecify one argument: \"on\" or \"off\"\n");
+ return 1;
+ }
+
+ sm501_gpio_init ();
+
+ if (strncmp (argv[1], "on", 2) == 0) {
+ *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_HIGH) &=
+ ~(BUZZER);
+ return 0;
+ } else if (strncmp (argv[1], "off", 3) == 0) {
+ *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_HIGH) |=
+ BUZZER;
+ return 0;
+ }
printf ("Usage:\nspecify one argument: \"on\" or \"off\"\n");
return 1;
- }
-
- sm501_gpio_init();
-
- if (strncmp (argv[1], "on", 2) == 0) {
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_HIGH) &= ~(BUZZER);
- return 0;
- }
- else if (strncmp (argv[1], "off", 3) == 0) {
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_HIGH) |= BUZZER;
- return 0;
- }
- printf ("Usage:\nspecify one argument: \"on\" or \"off\"\n");
- return 1;
}
-U_BOOT_CMD(
- buz , 2, 1, cmd_buz,
- "buz - turns buzzer on/off\n",
- "\n"
- "buz <on/off>\n"
- " - turns the buzzer on or off\n"
- );
+U_BOOT_CMD (buz, 2, 1, cmd_buz,
+ "buz - turns buzzer on/off\n",
+ "\n" "buz <on/off>\n" " - turns the buzzer on or off\n");
#endif /* CONFIG_BC3450_BUZZER */
/*
* fp - front panel commands
*/
-static int cmd_fp (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+static int cmd_fp (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
{
- sm501_gpio_init();
+ sm501_gpio_init ();
- if (strncmp (argv[1], "on", 2) == 0) {
- /* turn on VDD first */
- *(vu_long *)(SM501_MMIO_BASE + SM501_PANEL_DISPLAY_CONTROL) |= SM501_PDC_VDDEN;
- udelay(1000);
- /* then put data on */
- *(vu_long *)(SM501_MMIO_BASE + SM501_PANEL_DISPLAY_CONTROL) |= SM501_PDC_DATA;
- /* wait some time and enable backlight */
- udelay(1000);
- *(vu_long *)(SM501_MMIO_BASE + SM501_PANEL_DISPLAY_CONTROL) |= SM501_PDC_BIAS;
- udelay(1000);
- *(vu_long *)(SM501_MMIO_BASE + SM501_PANEL_DISPLAY_CONTROL) |= SM501_PDC_FPEN;
- return 0;
- }
- else if (strncmp (argv[1], "off", 3) == 0) {
- /* turn off the backlight first */
- *(vu_long *)(SM501_MMIO_BASE + SM501_PANEL_DISPLAY_CONTROL) &= ~SM501_PDC_FPEN;
- udelay(1000);
- *(vu_long *)(SM501_MMIO_BASE + SM501_PANEL_DISPLAY_CONTROL) &= ~SM501_PDC_BIAS;
- udelay(200000);
- /* wait some time, then remove data */
- *(vu_long *)(SM501_MMIO_BASE + SM501_PANEL_DISPLAY_CONTROL) &= ~SM501_PDC_DATA;
- udelay(1000);
- /* and remove VDD last */
- *(vu_long *)(SM501_MMIO_BASE + SM501_PANEL_DISPLAY_CONTROL) &= ~SM501_PDC_VDDEN;
- return 0;
- }
- else if (strncmp (argv[1], "bl", 2) == 0) {
- /* turn on/off backlight only */
- if (strncmp (argv[2], "on", 2) == 0) {
- *(vu_long *)(SM501_MMIO_BASE + SM501_PANEL_DISPLAY_CONTROL) |= SM501_PDC_BIAS;
- udelay(1000);
- *(vu_long *)(SM501_MMIO_BASE + SM501_PANEL_DISPLAY_CONTROL) |= SM501_PDC_FPEN;
- return 0;
+ if (strncmp (argv[1], "on", 2) == 0) {
+ /* turn on VDD first */
+ *(vu_long *) (SM501_MMIO_BASE +
+ SM501_PANEL_DISPLAY_CONTROL) |= SM501_PDC_VDDEN;
+ udelay (1000);
+ /* then put data on */
+ *(vu_long *) (SM501_MMIO_BASE +
+ SM501_PANEL_DISPLAY_CONTROL) |= SM501_PDC_DATA;
+ /* wait some time and enable backlight */
+ udelay (1000);
+ *(vu_long *) (SM501_MMIO_BASE +
+ SM501_PANEL_DISPLAY_CONTROL) |= SM501_PDC_BIAS;
+ udelay (1000);
+ *(vu_long *) (SM501_MMIO_BASE +
+ SM501_PANEL_DISPLAY_CONTROL) |= SM501_PDC_FPEN;
+ return 0;
+ } else if (strncmp (argv[1], "off", 3) == 0) {
+ /* turn off the backlight first */
+ *(vu_long *) (SM501_MMIO_BASE +
+ SM501_PANEL_DISPLAY_CONTROL) &= ~SM501_PDC_FPEN;
+ udelay (1000);
+ *(vu_long *) (SM501_MMIO_BASE +
+ SM501_PANEL_DISPLAY_CONTROL) &= ~SM501_PDC_BIAS;
+ udelay (200000);
+ /* wait some time, then remove data */
+ *(vu_long *) (SM501_MMIO_BASE +
+ SM501_PANEL_DISPLAY_CONTROL) &= ~SM501_PDC_DATA;
+ udelay (1000);
+ /* and remove VDD last */
+ *(vu_long *) (SM501_MMIO_BASE +
+ SM501_PANEL_DISPLAY_CONTROL) &=
+ ~SM501_PDC_VDDEN;
+ return 0;
+ } else if (strncmp (argv[1], "bl", 2) == 0) {
+ /* turn on/off backlight only */
+ if (strncmp (argv[2], "on", 2) == 0) {
+ *(vu_long *) (SM501_MMIO_BASE +
+ SM501_PANEL_DISPLAY_CONTROL) |=
+ SM501_PDC_BIAS;
+ udelay (1000);
+ *(vu_long *) (SM501_MMIO_BASE +
+ SM501_PANEL_DISPLAY_CONTROL) |=
+ SM501_PDC_FPEN;
+ return 0;
+ } else if (strncmp (argv[2], "off", 3) == 0) {
+ *(vu_long *) (SM501_MMIO_BASE +
+ SM501_PANEL_DISPLAY_CONTROL) &=
+ ~SM501_PDC_FPEN;
+ udelay (1000);
+ *(vu_long *) (SM501_MMIO_BASE +
+ SM501_PANEL_DISPLAY_CONTROL) &=
+ ~SM501_PDC_BIAS;
+ return 0;
+ }
}
- else if (strncmp (argv[2], "off", 3) == 0) {
- *(vu_long *)(SM501_MMIO_BASE + SM501_PANEL_DISPLAY_CONTROL) &= ~SM501_PDC_FPEN;
- udelay(1000);
- *(vu_long *)(SM501_MMIO_BASE + SM501_PANEL_DISPLAY_CONTROL) &= ~SM501_PDC_BIAS;
- return 0;
- }
- }
#ifdef CONFIG_BC3450_CRT
- else if (strncmp (argv[1], "crt", 3) == 0) {
- /* enables/disables the crt output (debug only) */
- if(strncmp (argv[2], "on", 2) == 0) {
- *(vu_long *)(SM501_MMIO_BASE + SM501_CRT_DISPLAY_CONTROL) |=
- (SM501_CDC_TE | SM501_CDC_E);
- *(vu_long *)(SM501_MMIO_BASE + SM501_CRT_DISPLAY_CONTROL) &=
- ~SM501_CDC_SEL;
- return 0;
+ else if (strncmp (argv[1], "crt", 3) == 0) {
+ /* enables/disables the crt output (debug only) */
+ if (strncmp (argv[2], "on", 2) == 0) {
+ *(vu_long *) (SM501_MMIO_BASE +
+ SM501_CRT_DISPLAY_CONTROL) |=
+ (SM501_CDC_TE | SM501_CDC_E);
+ *(vu_long *) (SM501_MMIO_BASE +
+ SM501_CRT_DISPLAY_CONTROL) &=
+ ~SM501_CDC_SEL;
+ return 0;
+ } else if (strncmp (argv[2], "off", 3) == 0) {
+ *(vu_long *) (SM501_MMIO_BASE +
+ SM501_CRT_DISPLAY_CONTROL) &=
+ ~(SM501_CDC_TE | SM501_CDC_E);
+ *(vu_long *) (SM501_MMIO_BASE +
+ SM501_CRT_DISPLAY_CONTROL) |=
+ SM501_CDC_SEL;
+ return 0;
+ }
}
- else if (strncmp (argv[2], "off", 3) == 0) {
- *(vu_long *)(SM501_MMIO_BASE + SM501_CRT_DISPLAY_CONTROL) &=
- ~(SM501_CDC_TE | SM501_CDC_E);
- *(vu_long *)(SM501_MMIO_BASE + SM501_CRT_DISPLAY_CONTROL) |=
- SM501_CDC_SEL;
- return 0;
- }
- }
#endif /* CONFIG_BC3450_CRT */
- printf("Usage:%s\n", cmdtp->help);
- return 1;
+ printf ("Usage:%s\n", cmdtp->help);
+ return 1;
}
-U_BOOT_CMD(
- fp , 3, 1, cmd_fp,
- "fp - front panes access functions\n",
- "\n"
- "fp bl <on/off>\n"
- " - turns the CCFL backlight of the display on/off\n"
- "fp <on/off>\n"
- " - turns the whole display on/off\n"
+U_BOOT_CMD (fp, 3, 1, cmd_fp,
+ "fp - front panes access functions\n",
+ "\n"
+ "fp bl <on/off>\n"
+ " - turns the CCFL backlight of the display on/off\n"
+ "fp <on/off>\n" " - turns the whole display on/off\n"
#ifdef CONFIG_BC3450_CRT
- "fp crt <on/off>\n"
- " - enables/disables the crt output (debug only)\n"
+ "fp crt <on/off>\n"
+ " - enables/disables the crt output (debug only)\n"
#endif /* CONFIG_BC3450_CRT */
- );
+ );
/*
* temp - DS1620 thermometer
*/
/* GERSYS BC3450 specific functions */
-static inline void bc_ds1620_set_clk(int clk)
+static inline void bc_ds1620_set_clk (int clk)
{
- if(clk)
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) |= DS1620_CLK;
- else
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) &= ~DS1620_CLK;
+ if (clk)
+ *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) |=
+ DS1620_CLK;
+ else
+ *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) &=
+ ~DS1620_CLK;
}
-static inline void bc_ds1620_set_data(int dat)
+static inline void bc_ds1620_set_data (int dat)
{
- if(dat)
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) |= DS1620_DQ;
- else
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) &= ~DS1620_DQ;
+ if (dat)
+ *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) |=
+ DS1620_DQ;
+ else
+ *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) &=
+ ~DS1620_DQ;
}
-static inline int bc_ds1620_get_data(void)
+static inline int bc_ds1620_get_data (void)
{
- vu_long rc;
- rc = *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW);
- rc &= DS1620_DQ;
- if(rc != 0)
- rc = 1;
- return (int)rc;
+ vu_long rc;
+
+ rc = *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW);
+ rc &= DS1620_DQ;
+ if (rc != 0)
+ rc = 1;
+ return (int) rc;
}
-static inline void bc_ds1620_set_data_dir(int dir)
+static inline void bc_ds1620_set_data_dir (int dir)
{
- if(dir) /* in */
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_DIR_LOW) &= ~DS1620_DQ;
- else /* out */
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_DIR_LOW) |= DS1620_DQ;
+ if (dir) /* in */
+ *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_DIR_LOW) &= ~DS1620_DQ;
+ else /* out */
+ *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_DIR_LOW) |= DS1620_DQ;
}
-static inline void bc_ds1620_set_reset(int res)
+static inline void bc_ds1620_set_reset (int res)
{
- if(res)
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) |= DS1620_RES;
- else
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) &= ~DS1620_RES;
+ if (res)
+ *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) |= DS1620_RES;
+ else
+ *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_LOW) &= ~DS1620_RES;
}
/* hardware independent functions */
-static void ds1620_send_bits(int nr, int value)
+static void ds1620_send_bits (int nr, int value)
{
- int i;
-
- for (i = 0; i < nr; i++) {
- bc_ds1620_set_data(value & 1);
- bc_ds1620_set_clk(0);
- udelay(1);
- bc_ds1620_set_clk(1);
- udelay(1);
-
- value >>= 1;
- }
+ int i;
+
+ for (i = 0; i < nr; i++) {
+ bc_ds1620_set_data (value & 1);
+ bc_ds1620_set_clk (0);
+ udelay (1);
+ bc_ds1620_set_clk (1);
+ udelay (1);
+
+ value >>= 1;
+ }
}
-static unsigned int ds1620_recv_bits(int nr)
+static unsigned int ds1620_recv_bits (int nr)
{
- unsigned int value = 0, mask = 1;
- int i;
+ unsigned int value = 0, mask = 1;
+ int i;
- bc_ds1620_set_data(0);
+ bc_ds1620_set_data (0);
- for (i = 0; i < nr; i++) {
- bc_ds1620_set_clk(0);
- udelay(1);
+ for (i = 0; i < nr; i++) {
+ bc_ds1620_set_clk (0);
+ udelay (1);
- if (bc_ds1620_get_data())
- value |= mask;
+ if (bc_ds1620_get_data ())
+ value |= mask;
- mask <<= 1;
+ mask <<= 1;
- bc_ds1620_set_clk(1);
- udelay(1);
- }
+ bc_ds1620_set_clk (1);
+ udelay (1);
+ }
- return value;
+ return value;
}
-static void ds1620_out(int cmd, int bits, int value)
+static void ds1620_out (int cmd, int bits, int value)
{
- bc_ds1620_set_clk(1);
- bc_ds1620_set_data_dir(0);
+ bc_ds1620_set_clk (1);
+ bc_ds1620_set_data_dir (0);
- bc_ds1620_set_reset(0);
- udelay(1);
- bc_ds1620_set_reset(1);
+ bc_ds1620_set_reset (0);
+ udelay (1);
+ bc_ds1620_set_reset (1);
- udelay(1);
+ udelay (1);
- ds1620_send_bits(8, cmd);
- if (bits)
- ds1620_send_bits(bits, value);
+ ds1620_send_bits (8, cmd);
+ if (bits)
+ ds1620_send_bits (bits, value);
- udelay(1);
+ udelay (1);
- /* go stand alone */
- bc_ds1620_set_data_dir(1);
- bc_ds1620_set_reset(0);
- bc_ds1620_set_clk(0);
+ /* go stand alone */
+ bc_ds1620_set_data_dir (1);
+ bc_ds1620_set_reset (0);
+ bc_ds1620_set_clk (0);
- udelay(10000);
+ udelay (10000);
}
-static unsigned int ds1620_in(int cmd, int bits)
+static unsigned int ds1620_in (int cmd, int bits)
{
- unsigned int value;
+ unsigned int value;
- bc_ds1620_set_clk(1);
- bc_ds1620_set_data_dir(0);
+ bc_ds1620_set_clk (1);
+ bc_ds1620_set_data_dir (0);
- bc_ds1620_set_reset(0);
- udelay(1);
- bc_ds1620_set_reset(1);
+ bc_ds1620_set_reset (0);
+ udelay (1);
+ bc_ds1620_set_reset (1);
- udelay(1);
+ udelay (1);
- ds1620_send_bits(8, cmd);
+ ds1620_send_bits (8, cmd);
- bc_ds1620_set_data_dir(1);
- value = ds1620_recv_bits(bits);
+ bc_ds1620_set_data_dir (1);
+ value = ds1620_recv_bits (bits);
- /* go stand alone */
- bc_ds1620_set_data_dir(1);
- bc_ds1620_set_reset(0);
- bc_ds1620_set_clk(0);
+ /* go stand alone */
+ bc_ds1620_set_data_dir (1);
+ bc_ds1620_set_reset (0);
+ bc_ds1620_set_clk (0);
- return value;
+ return value;
}
-static int cvt_9_to_int(unsigned int val)
+static int cvt_9_to_int (unsigned int val)
{
- if (val & 0x100)
- val |= 0xfffffe00;
+ if (val & 0x100)
+ val |= 0xfffffe00;
- return val;
+ return val;
}
/* set thermostate thresholds */
-static void ds1620_write_state(struct therm *therm)
+static void ds1620_write_state (struct therm *therm)
{
- ds1620_out(THERM_WRITE_TL, 9, therm->lo);
- ds1620_out(THERM_WRITE_TH, 9, therm->hi);
- ds1620_out(THERM_START_CONVERT, 0, 0);
+ ds1620_out (THERM_WRITE_TL, 9, therm->lo);
+ ds1620_out (THERM_WRITE_TH, 9, therm->hi);
+ ds1620_out (THERM_START_CONVERT, 0, 0);
}
-static int cmd_temp (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+static int cmd_temp (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
{
- int i;
- struct therm therm;
+ int i;
+ struct therm therm;
- sm501_gpio_init();
+ sm501_gpio_init ();
- /* print temperature */
- if (argc == 1) {
- i = cvt_9_to_int(ds1620_in(THERM_READ_TEMP, 9));
- printf("%d.%d C\n", i >> 1, i & 1 ? 5 : 0);
- return 0;
- }
-
- /* set to default operation */
- if (strncmp (argv[1], "set", 3) == 0) {
- if(strncmp (argv[2], "default", 3) == 0) {
- therm.hi = +88;
- therm.lo = -20;
- therm.hi <<= 1;
- therm.lo <<= 1;
- ds1620_write_state(&therm);
- ds1620_out(THERM_WRITE_CONFIG, 8, CFG_STANDALONE);
- return 0;
+ /* print temperature */
+ if (argc == 1) {
+ i = cvt_9_to_int (ds1620_in (THERM_READ_TEMP, 9));
+ printf ("%d.%d C\n", i >> 1, i & 1 ? 5 : 0);
+ return 0;
}
- }
- printf ("Usage:%s\n", cmdtp->help);
- return 1;
+ /* set to default operation */
+ if (strncmp (argv[1], "set", 3) == 0) {
+ if (strncmp (argv[2], "default", 3) == 0) {
+ therm.hi = +88;
+ therm.lo = -20;
+ therm.hi <<= 1;
+ therm.lo <<= 1;
+ ds1620_write_state (&therm);
+ ds1620_out (THERM_WRITE_CONFIG, 8, CFG_STANDALONE);
+ return 0;
+ }
+ }
+
+ printf ("Usage:%s\n", cmdtp->help);
+ return 1;
}
-U_BOOT_CMD(
- temp , 3, 1, cmd_temp,
- "temp - print current temperature\n",
- "\n"
- "temp\n"
- " - print current temperature\n"
-);
+U_BOOT_CMD (temp, 3, 1, cmd_temp,
+ "temp - print current temperature\n",
+ "\n" "temp\n" " - print current temperature\n");
#ifdef CONFIG_BC3450_CAN
/*
@@ -512,40 +533,40 @@
* return 1 on CAN initialization failure
* return 0 if no failure
*/
-int can_init(void)
+int can_init (void)
{
static int init_done = 0;
int i;
struct mpc5xxx_mscan *can1 =
- (struct mpc5xxx_mscan *)(CFG_MBAR + 0x0900);
+ (struct mpc5xxx_mscan *) (CFG_MBAR + 0x0900);
struct mpc5xxx_mscan *can2 =
- (struct mpc5xxx_mscan *)(CFG_MBAR + 0x0980);
+ (struct mpc5xxx_mscan *) (CFG_MBAR + 0x0980);
/* GPIO configuration of the CAN pins is done in BC3450.h */
if (!init_done) {
/* init CAN 1 */
can1->canctl1 |= 0x80; /* CAN enable */
- udelay(100);
+ udelay (100);
i = 0;
can1->canctl0 |= 0x02; /* sleep mode */
/* wait until sleep mode reached */
while (!(can1->canctl1 & 0x02)) {
- udelay(10);
- i++;
- if (i == 10) {
- printf ("%s: CAN1 initialize error, "
- "can not enter sleep mode!\n",
- __FUNCTION__);
- return 1;
- }
+ udelay (10);
+ i++;
+ if (i == 10) {
+ printf ("%s: CAN1 initialize error, "
+ "can not enter sleep mode!\n",
+ __FUNCTION__);
+ return 1;
+ }
}
i = 0;
can1->canctl0 = 0x01; /* enter init mode */
/* wait until init mode reached */
while (!(can1->canctl1 & 0x01)) {
- udelay(10);
+ udelay (10);
i++;
if (i == 10) {
printf ("%s: CAN1 initialize error, "
@@ -577,7 +598,7 @@
can1->canctl0 &= ~(0x02);
/* wait until init and sleep mode left */
while ((can1->canctl1 & 0x01) || (can1->canctl1 & 0x02)) {
- udelay(10);
+ udelay (10);
i++;
if (i == 10) {
printf ("%s: CAN1 initialize error, "
@@ -589,13 +610,13 @@
/* init CAN 2 */
can2->canctl1 |= 0x80; /* CAN enable */
- udelay(100);
+ udelay (100);
i = 0;
can2->canctl0 |= 0x02; /* sleep mode */
/* wait until sleep mode reached */
- while (!(can2->canctl1 & 0x02)) {
- udelay(10);
+ while (!(can2->canctl1 & 0x02)) {
+ udelay (10);
i++;
if (i == 10) {
printf ("%s: CAN2 initialize error, "
@@ -607,8 +628,8 @@
i = 0;
can2->canctl0 = 0x01; /* enter init mode */
/* wait until init mode reached */
- while (!(can2->canctl1 & 0x01)) {
- udelay(10);
+ while (!(can2->canctl1 & 0x01)) {
+ udelay (10);
i++;
if (i == 10) {
printf ("%s: CAN2 initialize error, "
@@ -640,7 +661,7 @@
i = 0;
/* wait until init mode left */
while ((can2->canctl1 & 0x01) || (can2->canctl1 & 0x02)) {
- udelay(10);
+ udelay (10);
i++;
if (i == 10) {
printf ("%s: CAN2 initialize error, "
@@ -661,13 +682,13 @@
* return 1 on CAN failure
* return 0 if no failure
*/
-int do_can(char *argv[])
+int do_can (char *argv[])
{
int i;
- struct mpc5xxx_mscan *can1 =
- (struct mpc5xxx_mscan *)(CFG_MBAR + 0x0900);
- struct mpc5xxx_mscan *can2 =
- (struct mpc5xxx_mscan *)(CFG_MBAR + 0x0980);
+ struct mpc5xxx_mscan *can1 =
+ (struct mpc5xxx_mscan *) (CFG_MBAR + 0x0900);
+ struct mpc5xxx_mscan *can2 =
+ (struct mpc5xxx_mscan *) (CFG_MBAR + 0x0980);
/* send a message on CAN1 */
can1->cantbsel = 0x01;
@@ -685,30 +706,27 @@
i++;
if (i == 10) {
printf ("%s: CAN1 send timeout, "
- "can not send message!\n",
- __FUNCTION__);
+ "can not send message!\n", __FUNCTION__);
return 1;
}
- udelay(1000);
+ udelay (1000);
}
- udelay(1000);
+ udelay (1000);
i = 0;
- while (!(can2->canrflg & 0x01)) {
+ while (!(can2->canrflg & 0x01)) {
i++;
if (i == 10) {
printf ("%s: CAN2 receive timeout, "
- "no message received!\n",
- __FUNCTION__);
+ "no message received!\n", __FUNCTION__);
return 1;
}
- udelay(1000);
+ udelay (1000);
}
-
+
if (can2->canrxfg.dsr[0] != 0xCC) {
printf ("%s: CAN2 receive error, "
- "data mismatch!\n",
- __FUNCTION__);
+ "data mismatch!\n", __FUNCTION__);
return 1;
}
@@ -728,24 +746,22 @@
i++;
if (i == 10) {
printf ("%s: CAN2 send error, "
- "can not send message!\n",
- __FUNCTION__);
+ "can not send message!\n", __FUNCTION__);
return 1;
}
- udelay(1000);
+ udelay (1000);
}
- udelay(1000);
+ udelay (1000);
i = 0;
- while (!(can1->canrflg & 0x01)) {
+ while (!(can1->canrflg & 0x01)) {
i++;
if (i == 10) {
printf ("%s: CAN1 receive timeout, "
- "no message received!\n",
- __FUNCTION__);
+ "no message received!\n", __FUNCTION__);
return 1;
}
- udelay(1000);
+ udelay (1000);
}
if (can1->canrxfg.dsr[0] != 0xCC) {
@@ -761,53 +777,51 @@
/*
* test - BC3450 HW test routines
*/
-int cmd_test(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+int cmd_test (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
{
#ifdef CONFIG_BC3450_CAN
- int rcode;
- can_init();
+ int rcode;
+
+ can_init ();
#endif /* CONFIG_BC3450_CAN */
- sm501_gpio_init();
+ sm501_gpio_init ();
- if (argc != 2) {
+ if (argc != 2) {
+ printf ("Usage:%s\n", cmdtp->help);
+ return 1;
+ }
+
+ if (strncmp (argv[1], "unit-off", 8) == 0) {
+ printf ("waiting 2 seconds...\n");
+ udelay (2000000);
+ *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_HIGH) &=
+ ~PWR_OFF;
+ return 0;
+ }
+#ifdef CONFIG_BC3450_CAN
+ else if (strncmp (argv[1], "can", 2) == 0) {
+ rcode = do_can (argv);
+ if (simple_strtoul (argv[2], NULL, 10) == 2) {
+ if (rcode == 0)
+ printf ("OK\n");
+ else
+ printf ("Error\n");
+ }
+ return rcode;
+ }
+#endif /* CONFIG_BC3450_CAN */
+
printf ("Usage:%s\n", cmdtp->help);
return 1;
- }
-
- if (strncmp (argv[1], "unit-off", 8) == 0) {
- printf ("waiting 2 seconds...\n");
- udelay(2000000);
- *(vu_long *) (SM501_MMIO_BASE + SM501_GPIO_DATA_HIGH) &= ~PWR_OFF;
- return 0;
- }
-#ifdef CONFIG_BC3450_CAN
- else if (strncmp (argv[1], "can", 2) == 0) {
- rcode = do_can (argv);
- if (simple_strtoul(argv[2], NULL, 10) == 2) {
- if (rcode == 0)
- printf ("OK\n");
- else
- printf ("Error\n");
- }
- return rcode;
- }
-#endif /* CONFIG_BC3450_CAN */
-
- printf ("Usage:%s\n", cmdtp->help);
- return 1;
}
-U_BOOT_CMD(
- test , 2, 1, cmd_test,
- "test - unit test routines\n",
- "\n"
+U_BOOT_CMD (test, 2, 1, cmd_test, "test - unit test routines\n", "\n"
#ifdef CONFIG_BC3450_CAN
- "test can\n"
- " - connect CAN1 (X8) with CAN2 (X9) for this test\n"
+ "test can\n"
+ " - connect CAN1 (X8) with CAN2 (X9) for this test\n"
#endif /* CONFIG_BC3450_CAN */
- "test unit-off\n"
- " - turns off the BC3450 unit\n"
- " WARNING: Unsaved environment variables will be lost!\n"
- );
+ "test unit-off\n"
+ " - turns off the BC3450 unit\n"
+ " WARNING: Unsaved environment variables will be lost!\n");
#endif /* CFG_CMD_BSP */
diff --git a/board/cobra5272/flash.c b/board/cobra5272/flash.c
index 73cc2f2..82452e2 100644
--- a/board/cobra5272/flash.c
+++ b/board/cobra5272/flash.c
@@ -65,6 +65,7 @@
printf ("\n");
Done:
+ return;
}
diff --git a/board/delta/delta.c b/board/delta/delta.c
index b7671dd..b127ac8 100644
--- a/board/delta/delta.c
+++ b/board/delta/delta.c
@@ -28,6 +28,8 @@
#include <common.h>
#include <i2c.h>
#include <da9030.h>
+#include <malloc.h>
+#include <command.h>
#include <asm/arch/pxa-regs.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -35,6 +37,9 @@
/* ------------------------------------------------------------------------- */
static void init_DA9030(void);
+static void keys_init(void);
+static void get_pressed_keys(uchar *s);
+static uchar *key_match(uchar *kbd_data);
/*
* Miscelaneous platform dependent initialisations
@@ -56,13 +61,216 @@
int board_late_init(void)
{
+#ifdef DELTA_CHECK_KEYBD
+ uchar kbd_data[KEYBD_DATALEN];
+ char keybd_env[2 * KEYBD_DATALEN + 1];
+ char *str;
+ int i;
+#endif /* DELTA_CHECK_KEYBD */
+
setenv("stdout", "serial");
setenv("stderr", "serial");
+
+#ifdef DELTA_CHECK_KEYBD
+ keys_init();
+
+ memset(kbd_data, '\0', KEYBD_DATALEN);
+
+ /* check for pressed keys and setup keybd_env */
+ get_pressed_keys(kbd_data);
+
+ for (i = 0; i < KEYBD_DATALEN; ++i) {
+ sprintf (keybd_env + i + i, "%02X", kbd_data[i]);
+ }
+ setenv ("keybd", keybd_env);
+
+ str = strdup ((char *)key_match (kbd_data)); /* decode keys */
+
+# ifdef CONFIG_PREBOOT /* automatically configure "preboot" command on key match */
+ setenv ("preboot", str); /* set or delete definition */
+# endif /* CONFIG_PREBOOT */
+ if (str != NULL) {
+ free (str);
+ }
+#endif /* DELTA_CHECK_KEYBD */
+
init_DA9030();
return 0;
}
+/*
+ * Magic Key Handling, mainly copied from board/lwmon/lwmon.c
+ */
+#ifdef DELTA_CHECK_KEYBD
+
+static uchar kbd_magic_prefix[] = "key_magic";
+static uchar kbd_command_prefix[] = "key_cmd";
+
+/*
+ * Get pressed keys
+ * s is a buffer of size KEYBD_DATALEN-1
+ */
+static void get_pressed_keys(uchar *s)
+{
+ unsigned long val;
+ val = GPLR3;
+
+ if(val & (1<<31))
+ *s++ = KEYBD_KP_DKIN0;
+ if(val & (1<<18))
+ *s++ = KEYBD_KP_DKIN1;
+ if(val & (1<<29))
+ *s++ = KEYBD_KP_DKIN2;
+ if(val & (1<<22))
+ *s++ = KEYBD_KP_DKIN5;
+}
+
+static void keys_init()
+{
+ CKENB |= CKENB_7_GPIO;
+ udelay(100);
+
+ /* Configure GPIOs */
+ GPIO127 = 0xa840; /* KP_DKIN0 */
+ GPIO114 = 0xa840; /* KP_DKIN1 */
+ GPIO125 = 0xa840; /* KP_DKIN2 */
+ GPIO118 = 0xa840; /* KP_DKIN5 */
+
+ /* Configure GPIOs as inputs */
+ GPDR3 &= ~(1<<31 | 1<<18 | 1<<29 | 1<<22);
+ GCDR3 = (1<<31 | 1<<18 | 1<<29 | 1<<22);
+
+ udelay(100);
+}
+
+static int compare_magic (uchar *kbd_data, uchar *str)
+{
+ /* uchar compare[KEYBD_DATALEN-1]; */
+ uchar compare[KEYBD_DATALEN];
+ char *nxt;
+ int i;
+
+ /* Don't include modifier byte */
+ /* memcpy (compare, kbd_data+1, KEYBD_DATALEN-1); */
+ memcpy (compare, kbd_data, KEYBD_DATALEN);
+
+ for (; str != NULL; str = (*nxt) ? (uchar *)(nxt+1) : (uchar *)nxt) {
+ uchar c;
+ int k;
+
+ c = (uchar) simple_strtoul ((char *)str, (char **) (&nxt), 16);
+
+ if (str == (uchar *)nxt) { /* invalid character */
+ break;
+ }
+
+ /*
+ * Check if this key matches the input.
+ * Set matches to zero, so they match only once
+ * and we can find duplicates or extra keys
+ */
+ for (k = 0; k < sizeof(compare); ++k) {
+ if (compare[k] == '\0') /* only non-zero entries */
+ continue;
+ if (c == compare[k]) { /* found matching key */
+ compare[k] = '\0';
+ break;
+ }
+ }
+ if (k == sizeof(compare)) {
+ return -1; /* unmatched key */
+ }
+ }
+
+ /*
+ * A full match leaves no keys in the `compare' array,
+ */
+ for (i = 0; i < sizeof(compare); ++i) {
+ if (compare[i])
+ {
+ return -1;
+ }
+ }
+
+ return 0;
+}
+
+
+static uchar *key_match (uchar *kbd_data)
+{
+ char magic[sizeof (kbd_magic_prefix) + 1];
+ uchar *suffix;
+ char *kbd_magic_keys;
+
+ /*
+ * The following string defines the characters that can pe appended
+ * to "key_magic" to form the names of environment variables that
+ * hold "magic" key codes, i. e. such key codes that can cause
+ * pre-boot actions. If the string is empty (""), then only
+ * "key_magic" is checked (old behaviour); the string "125" causes
+ * checks for "key_magic1", "key_magic2" and "key_magic5", etc.
+ */
+ if ((kbd_magic_keys = getenv ("magic_keys")) == NULL)
+ kbd_magic_keys = "";
+
+ /* loop over all magic keys;
+ * use '\0' suffix in case of empty string
+ */
+ for (suffix=(uchar *)kbd_magic_keys; *suffix || suffix==(uchar *)kbd_magic_keys; ++suffix) {
+ sprintf (magic, "%s%c", kbd_magic_prefix, *suffix);
+#if 0
+ printf ("### Check magic \"%s\"\n", magic);
+#endif
+ if (compare_magic(kbd_data, (uchar *)getenv(magic)) == 0) {
+ char cmd_name[sizeof (kbd_command_prefix) + 1];
+ char *cmd;
+
+ sprintf (cmd_name, "%s%c", kbd_command_prefix, *suffix);
+
+ cmd = getenv (cmd_name);
+#if 0
+ printf ("### Set PREBOOT to $(%s): \"%s\"\n",
+ cmd_name, cmd ? cmd : "<<NULL>>");
+#endif
+ *kbd_data = *suffix;
+ return ((uchar *)cmd);
+ }
+ }
+#if 0
+ printf ("### Delete PREBOOT\n");
+#endif
+ *kbd_data = '\0';
+ return (NULL);
+}
+
+int do_kbd (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+ uchar kbd_data[KEYBD_DATALEN];
+ char keybd_env[2 * KEYBD_DATALEN + 1];
+ int i;
+
+ /* Read keys */
+ get_pressed_keys(kbd_data);
+ puts ("Keys:");
+ for (i = 0; i < KEYBD_DATALEN; ++i) {
+ sprintf (keybd_env + i + i, "%02X", kbd_data[i]);
+ printf (" %02x", kbd_data[i]);
+ }
+ putc ('\n');
+ setenv ("keybd", keybd_env);
+ return 0;
+}
+
+U_BOOT_CMD(
+ kbd, 1, 1, do_kbd,
+ "kbd - read keyboard status\n",
+ NULL
+);
+
+#endif /* DELTA_CHECK_KEYBD */
+
+
int dram_init (void)
{
gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
diff --git a/board/mpc8349ads/Makefile b/board/m5271evb/Makefile
similarity index 80%
rename from board/mpc8349ads/Makefile
rename to board/m5271evb/Makefile
index f865f9c..34de983 100644
--- a/board/mpc8349ads/Makefile
+++ b/board/m5271evb/Makefile
@@ -1,5 +1,6 @@
#
-# Copyright 2004 Freescale Semiconductor, Inc.
+# (C) Copyright 2000-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
# See file CREDITS for list of people who contributed to this
# project.
@@ -24,22 +25,16 @@
LIB = lib$(BOARD).a
-OBJS := $(BOARD).o pci.o
+OBJS = $(BOARD).o
-$(LIB): $(OBJS) $(SOBJS)
+$(LIB): .depend $(OBJS)
$(AR) crv $@ $(OBJS)
-clean:
- rm -f $(SOBJS) $(OBJS)
-
-distclean: clean
- rm -f $(LIB) core *.bak .depend
-
#########################################################################
.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
- $(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+ $(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
--include .depend
+sinclude .depend
#########################################################################
diff --git a/board/mpc8349ads/config.mk b/board/m5271evb/config.mk
similarity index 82%
rename from board/mpc8349ads/config.mk
rename to board/m5271evb/config.mk
index 4602169..9a7af7c 100644
--- a/board/mpc8349ads/config.mk
+++ b/board/m5271evb/config.mk
@@ -1,5 +1,7 @@
#
-# Copyright 2004 Freescale Semiconductor, Inc.
+# (C) Copyright 2000-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+# Coldfire contribution by Bernhard Kuhn <bkuhn@metrowerks.com>
#
# See file CREDITS for list of people who contributed to this
# project.
@@ -20,8 +22,4 @@
# MA 02111-1307 USA
#
-#
-# MPC83xxADS
-#
-
-TEXT_BASE = 0xFE700000
+TEXT_BASE = 0xffe00000
diff --git a/board/m5271evb/m5271evb.c b/board/m5271evb/m5271evb.c
new file mode 100644
index 0000000..d364bd6
--- /dev/null
+++ b/board/m5271evb/m5271evb.c
@@ -0,0 +1,125 @@
+/*
+ * (C) Copyright 2000-2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/m5271.h>
+#include <asm/immap_5271.h>
+
+int checkboard (void) {
+ puts ("Board: Freescale M5271EVB\n");
+ return 0;
+};
+
+long int initdram (int board_type) {
+
+ int i;
+
+ /* Enable Address lines 23-21 and lower 16bits of data path */
+ mbar_writeByte(MCF_GPIO_PAR_AD, MCF_GPIO_AD_ADDR23 |
+ MCF_GPIO_AD_ADDR22 | MCF_GPIO_AD_ADDR21 |
+ MCF_GPIO_AD_DATAL);
+
+ /* Set CS2 pin to be SD_CS0 */
+ mbar_writeByte(MCF_GPIO_PAR_CS, mbar_readByte(MCF_GPIO_PAR_CS)
+ | MCF_GPIO_PAR_CS_PAR_CS2);
+
+ /* Configure SDRAM Control Pin Assignemnt Register */
+ mbar_writeByte(MCF_GPIO_PAR_SDRAM, MCF_GPIO_SDRAM_CSSDCS_00 |
+ MCF_GPIO_SDRAM_SDWE | MCF_GPIO_SDRAM_SCAS |
+ MCF_GPIO_SDRAM_SRAS | MCF_GPIO_SDRAM_SCKE |
+ MCF_GPIO_SDRAM_SDCS_11);
+
+ /*
+ * Check to see if the SDRAM has already been initialized
+ * by a run control tool
+ */
+ if (!(mbar_readLong(MCF_SDRAMC_DACR0) & MCF_SDRAMC_DACRn_RE))
+ {
+ /* Initialize DRAM Control Register: DCR */
+ mbar_writeShort(MCF_SDRAMC_DCR,
+ MCF_SDRAMC_DCR_RTIM(0x01)
+ | MCF_SDRAMC_DCR_RC(0x30));
+
+ /*
+ * Initialize DACR0
+ *
+ * CASL: 01
+ * CBM: cmd at A20, bank select bits 21 and up
+ * PS: 32bit port size
+ */
+ mbar_writeLong(MCF_SDRAMC_DACR0,
+ MCF_SDRAMC_DACRn_BA(CFG_SDRAM_BASE>>18)
+ | MCF_SDRAMC_DACRn_CASL(1)
+ | MCF_SDRAMC_DACRn_CBM(3)
+ | MCF_SDRAMC_DACRn_PS(0));
+
+ /* Initialize DMR0 */
+ mbar_writeLong(MCF_SDRAMC_DMR0,
+ MCF_SDRAMC_DMRn_BAM_16M
+ | MCF_SDRAMC_DMRn_V);
+
+ /* Set IP bit in DACR */
+ mbar_writeLong(MCF_SDRAMC_DACR0, mbar_readLong(MCF_SDRAMC_DACR0)
+ | MCF_SDRAMC_DACRn_IP);
+
+ /* Wait at least 20ns to allow banks to precharge */
+ for (i = 0; i < 5; i++)
+ asm(" nop");
+
+ /* Write to this block to initiate precharge */
+ *(u32 *)(CFG_SDRAM_BASE) = 0xa5a5a5a5;
+
+ /* Set RE bit in DACR */
+ mbar_writeLong(MCF_SDRAMC_DACR0, mbar_readLong(MCF_SDRAMC_DACR0)
+ | MCF_SDRAMC_DACRn_RE);
+
+ /* Wait for at least 8 auto refresh cycles to occur */
+ for (i = 0; i < 2000; i++)
+ asm(" nop");
+
+ /* Finish the configuration by issuing the MRS */
+ mbar_writeLong(MCF_SDRAMC_DACR0, mbar_readLong(MCF_SDRAMC_DACR0)
+ | MCF_SDRAMC_DACRn_MRS);
+
+ /*
+ * Write to the SDRAM Mode Register A0-A11 = 0x400
+ *
+ * Write Burst Mode = Programmed Burst Length
+ * Op Mode = Standard Op
+ * CAS Latency = 2
+ * Burst Type = Sequential
+ * Burst Length = 1
+ */
+ *(u32 *)(CFG_SDRAM_BASE + 0x400) = 0xa5a5a5a5;
+ }
+
+ return CFG_SDRAM_SIZE * 1024 * 1024;
+};
+
+int testdram (void) {
+
+ /* TODO: XXX XXX XXX */
+ printf ("DRAM test not implemented!\n");
+
+ return (0);
+}
diff --git a/board/mpc8349ads/u-boot.lds b/board/m5271evb/u-boot.lds
similarity index 73%
copy from board/mpc8349ads/u-boot.lds
copy to board/m5271evb/u-boot.lds
index 020cfa6..69f3179 100644
--- a/board/mpc8349ads/u-boot.lds
+++ b/board/m5271evb/u-boot.lds
@@ -1,5 +1,6 @@
/*
- * Copyright 2004 Freescale Semiconductor, Inc.
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -20,7 +21,11 @@
* MA 02111-1307 USA
*/
-OUTPUT_ARCH(powerpc)
+OUTPUT_ARCH(m68k)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib);
+/* Do we need any of these for elf?
+ __DYNAMIC = 0; */
+GROUP(libgcc.a)
SECTIONS
{
/* Read-only sections, merged into text segment: */
@@ -49,34 +54,50 @@
.plt : { *(.plt) }
.text :
{
- cpu/mpc83xx/start.o (.text)
+ /* WARNING - the following is hand-optimized to fit within */
+ /* the sector layout of our flash chips! XXX FIXME XXX */
+
+ cpu/mcf52x2/start.o (.text)
+ lib_m68k/traps.o (.text)
+ cpu/mcf52x2/interrupts.o (.text)
+ common/dlmalloc.o (.text)
+ lib_generic/zlib.o (.text)
+
+ . = DEFINED(env_offset) ? env_offset : .;
+ common/environment.o (.ppcenv)
+
*(.text)
*(.fixup)
*(.got1)
- . = ALIGN(16);
+ }
+ _etext = .;
+ PROVIDE (etext = .);
+ .rodata :
+ {
*(.rodata)
*(.rodata1)
- *(.rodata.str1.4)
- *(.eh_frame)
}
.fini : { *(.fini) } =0
.ctors : { *(.ctors) }
.dtors : { *(.dtors) }
/* Read-write section, merged into data segment: */
- . = (. + 0x0FFF) & 0xFFFFF000;
+ . = (. + 0x00FF) & 0xFFFFFF00;
_erotext = .;
PROVIDE (erotext = .);
+
.reloc :
{
+ __got_start = .;
*(.got)
+ __got_end = .;
_GOT2_TABLE_ = .;
*(.got2)
_FIXUP_TABLE_ = .;
*(.fixup)
}
- __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
- __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+ __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+ __fixup_entries = (. - _FIXUP_TABLE_)>>2;
.data :
{
@@ -101,22 +122,24 @@
__ex_table : { *(__ex_table) }
__stop___ex_table = .;
- . = ALIGN(4096);
+ . = ALIGN(256);
__init_begin = .;
.text.init : { *(.text.init) }
.data.init : { *(.data.init) }
- . = ALIGN(4096);
+ . = ALIGN(256);
__init_end = .;
__bss_start = .;
.bss :
{
+ _sbss = .;
*(.sbss) *(.scommon)
*(.dynbss)
*(.bss)
*(COMMON)
+ . = ALIGN(4);
+ _ebss = .;
}
_end = . ;
PROVIDE (end = .);
}
-ENTRY(_start)
diff --git a/board/m5272c3/flash.c b/board/m5272c3/flash.c
index f156342..ea0b1fd 100644
--- a/board/m5272c3/flash.c
+++ b/board/m5272c3/flash.c
@@ -65,6 +65,7 @@
printf ("\n");
Done:
+ return;
}
diff --git a/board/m5282evb/flash.c b/board/m5282evb/flash.c
index 95f35ad..36a7c31 100644
--- a/board/m5282evb/flash.c
+++ b/board/m5282evb/flash.c
@@ -65,6 +65,7 @@
printf ("\n");
Done:
+ return;
}
diff --git a/board/mpc8349ads/mpc8349ads.c b/board/mpc8349ads/mpc8349ads.c
deleted file mode 100644
index 9841298..0000000
--- a/board/mpc8349ads/mpc8349ads.c
+++ /dev/null
@@ -1,235 +0,0 @@
-/*
- * Copyright Freescale Semiconductor, Inc.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- *
- * Change log:
- * 20050101: Eran Liberty (liberty@freescale.com)
- * Initial file creating (porting from 85XX & 8260)
- */
-
-#include <common.h>
-#include <ioports.h>
-#include <mpc83xx.h>
-#include <asm/mpc8349_pci.h>
-#include <i2c.h>
-#include <spd.h>
-#include <miiphy.h>
-#if defined(CONFIG_PCI)
-#include <pci.h>
-#endif
-#if defined(CONFIG_SPD_EEPROM)
-#include <spd_sdram.h>
-#endif
-int fixed_sdram(void);
-void sdram_init(void);
-
-int board_early_init_f (void)
-{
- volatile u8* bcsr = (volatile u8*)CFG_BCSR;
-
- /* Enable flash write */
- bcsr[1] &= ~0x01;
-
- return 0;
-}
-
-
-#define ns2clk(ns) (ns / (1000000000 / CONFIG_8349_CLKIN) + 1)
-
-long int initdram (int board_type)
-{
- volatile immap_t *im = (immap_t *)CFG_IMMRBAR;
- u32 msize = 0;
-
- if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32)im)
- return -1;
-
- /* DDR SDRAM - Main SODIMM */
- im->sysconf.ddrlaw[0].bar = CFG_DDR_BASE & LAWBAR_BAR;
-#if defined(CONFIG_SPD_EEPROM)
- msize = spd_sdram();
-#else
- msize = fixed_sdram();
-#endif
- /*
- * Initialize SDRAM if it is on local bus.
- */
- sdram_init();
- puts(" DDR RAM: ");
- /* return total bus SDRAM size(bytes) -- DDR */
- return (msize * 1024 * 1024);
-}
-
-
-#if !defined(CONFIG_SPD_EEPROM)
-/*************************************************************************
- * fixed sdram init -- doesn't use serial presence detect.
- ************************************************************************/
-int fixed_sdram(void)
-{
- volatile immap_t *im = (immap_t *)CFG_IMMRBAR;
- u32 msize = 0;
- u32 ddr_size;
- u32 ddr_size_log2;
-
- msize = CFG_DDR_SIZE;
- for (ddr_size = msize << 20, ddr_size_log2 = 0;
- (ddr_size > 1);
- ddr_size = ddr_size>>1, ddr_size_log2++) {
- if (ddr_size & 1) {
- return -1;
- }
- }
- im->sysconf.ddrlaw[0].ar = LAWAR_EN | ((ddr_size_log2 - 1) & LAWAR_SIZE);
-#if (CFG_DDR_SIZE != 256)
-#warning Currenly any ddr size other than 256 is not supported
-#endif
-
- im->ddr.csbnds[0].csbnds = 0x00100017;
- im->ddr.csbnds[1].csbnds = 0x0018001f;
- im->ddr.csbnds[2].csbnds = 0x00000007;
- im->ddr.csbnds[3].csbnds = 0x0008000f;
- im->ddr.cs_config[0] = CFG_DDR_CONFIG;
- im->ddr.cs_config[1] = CFG_DDR_CONFIG;
- im->ddr.cs_config[2] = CFG_DDR_CONFIG;
- im->ddr.cs_config[3] = CFG_DDR_CONFIG;
- im->ddr.timing_cfg_1 =
- 3 << TIMING_CFG1_PRETOACT_SHIFT |
- 7 << TIMING_CFG1_ACTTOPRE_SHIFT |
- 3 << TIMING_CFG1_ACTTORW_SHIFT |
- 4 << TIMING_CFG1_CASLAT_SHIFT |
- 3 << TIMING_CFG1_REFREC_SHIFT |
- 3 << TIMING_CFG1_WRREC_SHIFT |
- 2 << TIMING_CFG1_ACTTOACT_SHIFT |
- 1 << TIMING_CFG1_WRTORD_SHIFT;
- im->ddr.timing_cfg_2 = 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT;
- im->ddr.sdram_cfg =
- SDRAM_CFG_SREN
-#if defined(CONFIG_DDR_2T_TIMING)
- | SDRAM_CFG_2T_EN
-#endif
- | 2 << SDRAM_CFG_SDRAM_TYPE_SHIFT;
- im->ddr.sdram_mode =
- 0x2000 << SDRAM_MODE_ESD_SHIFT |
- 0x0162 << SDRAM_MODE_SD_SHIFT;
-
- im->ddr.sdram_interval = 0x045B << SDRAM_INTERVAL_REFINT_SHIFT |
- 0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT;
- udelay(200);
-
- im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN;
-
- return msize;
-}
-#endif/*!CFG_SPD_EEPROM*/
-
-
-int checkboard (void)
-{
- puts("Board: Freescale MPC8349ADS\n");
- return 0;
-}
-
-/*
- * if MPC8349ADS is soldered with SDRAM
- */
-#if defined(CFG_BR2_PRELIM) \
- && defined(CFG_OR2_PRELIM) \
- && defined(CFG_LBLAWBAR2_PRELIM) \
- && defined(CFG_LBLAWAR2_PRELIM)
-/*
- * Initialize SDRAM memory on the Local Bus.
- */
-
-void
-sdram_init(void)
-{
- volatile immap_t *immap = (immap_t *)CFG_IMMRBAR;
- volatile lbus8349_t *lbc= &immap->lbus;
- uint *sdram_addr = (uint *)CFG_LBC_SDRAM_BASE;
-
- puts("\n SDRAM on Local Bus: ");
- print_size (CFG_LBC_SDRAM_SIZE * 1024 * 1024, "\n");
-
- /*
- * Setup SDRAM Base and Option Registers, already done in cpu_init.c
- */
-
- /*setup mtrpt, lsrt and lbcr for LB bus*/
- lbc->lbcr = CFG_LBC_LBCR;
- lbc->mrtpr = CFG_LBC_MRTPR;
- lbc->lsrt = CFG_LBC_LSRT;
- asm("sync");
-
- /*
- * Configure the SDRAM controller Machine Mode Register.
- */
- lbc->lsdmr = CFG_LBC_LSDMR_5; /* 0x40636733; normal operation*/
-
- lbc->lsdmr = CFG_LBC_LSDMR_1; /*0x68636733;precharge all the banks*/
- asm("sync");
- *sdram_addr = 0xff;
- udelay(100);
-
- lbc->lsdmr = CFG_LBC_LSDMR_2;/*0x48636733;auto refresh*/
- asm("sync");
- /*1 times*/
- *sdram_addr = 0xff;
- udelay(100);
- /*2 times*/
- *sdram_addr = 0xff;
- udelay(100);
- /*3 times*/
- *sdram_addr = 0xff;
- udelay(100);
- /*4 times*/
- *sdram_addr = 0xff;
- udelay(100);
- /*5 times*/
- *sdram_addr = 0xff;
- udelay(100);
- /*6 times*/
- *sdram_addr = 0xff;
- udelay(100);
- /*7 times*/
- *sdram_addr = 0xff;
- udelay(100);
- /*8 times*/
- *sdram_addr = 0xff;
- udelay(100);
-
- /* 0x58636733;mode register write operation */
- lbc->lsdmr = CFG_LBC_LSDMR_4;
- asm("sync");
- *sdram_addr = 0xff;
- udelay(100);
-
- lbc->lsdmr = CFG_LBC_LSDMR_5; /*0x40636733;normal operation*/
- asm("sync");
- *sdram_addr = 0xff;
- udelay(100);
-}
-#else
-void
-sdram_init(void)
-{
- put("SDRAM on Local Bus is NOT available!\n");
-}
-#endif
diff --git a/board/mpc8349emds/mpc8349emds.c b/board/mpc8349emds/mpc8349emds.c
index 7ece7db..b5ccb53 100644
--- a/board/mpc8349emds/mpc8349emds.c
+++ b/board/mpc8349emds/mpc8349emds.c
@@ -30,9 +30,6 @@
#include <spd.h>
#include <miiphy.h>
#include <command.h>
-#if defined(CONFIG_PCI)
-#include <pci.h>
-#endif
#if defined(CONFIG_SPD_EEPROM)
#include <spd_sdram.h>
#endif
@@ -50,6 +47,11 @@
/* Enable flash write */
bcsr[1] &= ~0x01;
+#ifdef CFG_USE_MPC834XSYS_USB_PHY
+ /* Use USB PHY on SYS board */
+ bcsr[5] |= 0x02;
+#endif
+
return 0;
}
@@ -152,44 +154,6 @@
return 0;
}
-#if defined(CONFIG_PCI)
-/*
- * Initialize PCI Devices, report devices found
- */
-#ifndef CONFIG_PCI_PNP
-static struct pci_config_table pci_mpc8349emds_config_table[] = {
- {PCI_ANY_ID,PCI_ANY_ID,PCI_ANY_ID,PCI_ANY_ID,
- pci_cfgfunc_config_device, {PCI_ENET0_IOADDR,
- PCI_ENET0_MEMADDR,
- PCI_COMMON_MEMORY | PCI_COMMAND_MASTER
- } },
- {}
-}
-#endif
-
-volatile static struct pci_controller hose[] = {
- {
-#ifndef CONFIG_PCI_PNP
- config_table:pci_mpc8349emds_config_table,
-#endif
- },
- {
-#ifndef CONFIG_PCI_PNP
- config_table:pci_mpc8349emds_config_table,
-#endif
- }
-};
-#endif /* CONFIG_PCI */
-
-void pci_init_board(void)
-{
-#ifdef CONFIG_PCI
- extern void pci_mpc83xx_init(volatile struct pci_controller *hose);
-
- pci_mpc83xx_init(hose);
-#endif /* CONFIG_PCI */
-}
-
/*
* if MPC8349EMDS is soldered with SDRAM
*/
diff --git a/board/mpc8349ads/pci.c b/board/mpc8349emds/pci.c
similarity index 97%
rename from board/mpc8349ads/pci.c
rename to board/mpc8349emds/pci.c
index 319e35c..63e4405 100644
--- a/board/mpc8349ads/pci.c
+++ b/board/mpc8349emds/pci.c
@@ -35,7 +35,7 @@
#define CONFIG_PCI_SYS_MEM_PHYS CFG_SDRAM_BASE
#ifndef CONFIG_PCI_PNP
-static struct pci_config_table pci_mpc83xxads_config_table[] = {
+static struct pci_config_table pci_mpc8349emds_config_table[] = {
{PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
PCI_IDSEL_NUMBER, PCI_ANY_ID,
pci_cfgfunc_config_device, {PCI_ENET0_IOADDR,
@@ -50,12 +50,12 @@
static struct pci_controller pci_hose[] = {
{
#ifndef CONFIG_PCI_PNP
- config_table:pci_mpc83xxads_config_table,
+ config_table:pci_mpc8349emds_config_table,
#endif
},
{
#ifndef CONFIG_PCI_PNP
- config_table:pci_mpc83xxads_config_table,
+ config_table:pci_mpc8349emds_config_table,
#endif
}
};
@@ -188,7 +188,7 @@
pci_law[0].ar = LAWAR_EN | LAWAR_SIZE_1G;
pci_law[1].bar = CFG_PCI1_IO_PHYS & LAWBAR_BAR;
- pci_law[1].ar = LAWAR_EN | LAWAR_SIZE_32M;
+ pci_law[1].ar = LAWAR_EN | LAWAR_SIZE_4M;
/*
* Configure PCI Outbound Translation Windows
@@ -378,4 +378,5 @@
#endif
}
+
#endif /* CONFIG_PCI */
diff --git a/board/nc650/nand.c b/board/nc650/nand.c
index f27e536..de54386 100644
--- a/board/nc650/nand.c
+++ b/board/nc650/nand.c
@@ -37,22 +37,22 @@
struct nand_chip *this = mtd->priv;
switch(cmd) {
- case NAND_CTL_SETCLE:
- this->IO_ADDR_W += 2;
- break;
- case NAND_CTL_CLRCLE:
- this->IO_ADDR_W -= 2;
- break;
- case NAND_CTL_SETALE:
- this->IO_ADDR_W += 1;
- break;
- case NAND_CTL_CLRALE:
- this->IO_ADDR_W -= 1;
- break;
- case NAND_CTL_SETNCE:
- case NAND_CTL_CLRNCE:
- /* nop */
- break;
+ case NAND_CTL_SETCLE:
+ this->IO_ADDR_W += 2;
+ break;
+ case NAND_CTL_CLRCLE:
+ this->IO_ADDR_W -= 2;
+ break;
+ case NAND_CTL_SETALE:
+ this->IO_ADDR_W += 1;
+ break;
+ case NAND_CTL_CLRALE:
+ this->IO_ADDR_W -= 1;
+ break;
+ case NAND_CTL_SETNCE:
+ case NAND_CTL_CLRNCE:
+ /* nop */
+ break;
}
}
#elif defined(CONFIG_IDS852_REV2)
@@ -64,24 +64,24 @@
struct nand_chip *this = mtd->priv;
switch(cmd) {
- case NAND_CTL_SETCLE:
- *(((volatile __u8 *) this->IO_ADDR_W) + 0xa) = 0;
- break;
- case NAND_CTL_CLRCLE:
- *(((volatile __u8 *) this->IO_ADDR_W) + 0x8) = 0;
- break;
- case NAND_CTL_SETALE:
- *(((volatile __u8 *) this->IO_ADDR_W) + 0x9) = 0;
- break;
- case NAND_CTL_CLRALE:
- *(((volatile __u8 *) this->IO_ADDR_W) + 0x8) = 0;
- break;
- case NAND_CTL_SETNCE:
- *(((volatile __u8 *) this->IO_ADDR_W) + 0x8) = 0;
- break;
- case NAND_CTL_CLRNCE:
- *(((volatile __u8 *) this->IO_ADDR_W) + 0xc) = 0;
- break;
+ case NAND_CTL_SETCLE:
+ *(((volatile __u8 *) this->IO_ADDR_W) + 0xa) = 0;
+ break;
+ case NAND_CTL_CLRCLE:
+ *(((volatile __u8 *) this->IO_ADDR_W) + 0x8) = 0;
+ break;
+ case NAND_CTL_SETALE:
+ *(((volatile __u8 *) this->IO_ADDR_W) + 0x9) = 0;
+ break;
+ case NAND_CTL_CLRALE:
+ *(((volatile __u8 *) this->IO_ADDR_W) + 0x8) = 0;
+ break;
+ case NAND_CTL_SETNCE:
+ *(((volatile __u8 *) this->IO_ADDR_W) + 0x8) = 0;
+ break;
+ case NAND_CTL_CLRNCE:
+ *(((volatile __u8 *) this->IO_ADDR_W) + 0xc) = 0;
+ break;
}
}
#else
diff --git a/board/nc650/nc650.c b/board/nc650/nc650.c
index c90ac9c..8a6b5b0 100644
--- a/board/nc650/nc650.c
+++ b/board/nc650/nc650.c
@@ -265,8 +265,8 @@
int iCompatMode = 0;
char *pParam = NULL;
char *envlb;
-
- /*
+
+ /*
First byte in CPLD read address space signals compatibility mode
0 - cp850
1 - kp852
@@ -274,9 +274,9 @@
pParam = (char*)(CFG_CPLD_BASE);
if( *pParam != 0)
iCompatMode = 1;
-
+
if ( iCompatMode != 0) {
- /*
+ /*
In KP852 compatibility mode we have to write to
DPRAM as early as possible the binary coded
line config and board name.
@@ -288,7 +288,7 @@
setenv( DPRAM_VARNAME, DEFAULT_LB);
envlb = DEFAULT_LB;
}
-
+
/* Status string */
printf("Mode: KP852(LB=%s)\n", envlb);
@@ -305,7 +305,7 @@
} else {
puts("Mode: CP850\n");
}
-
+
return 0;
}
#endif
diff --git a/board/mpc8349ads/Makefile b/board/r5200/Makefile
similarity index 80%
copy from board/mpc8349ads/Makefile
copy to board/r5200/Makefile
index f865f9c..d0364ed 100644
--- a/board/mpc8349ads/Makefile
+++ b/board/r5200/Makefile
@@ -1,5 +1,6 @@
#
-# Copyright 2004 Freescale Semiconductor, Inc.
+# (C) Copyright 2000-2003
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
# See file CREDITS for list of people who contributed to this
# project.
@@ -24,22 +25,16 @@
LIB = lib$(BOARD).a
-OBJS := $(BOARD).o pci.o
+OBJS = $(BOARD).o
-$(LIB): $(OBJS) $(SOBJS)
+$(LIB): .depend $(OBJS)
$(AR) crv $@ $(OBJS)
-clean:
- rm -f $(SOBJS) $(OBJS)
-
-distclean: clean
- rm -f $(LIB) core *.bak .depend
-
#########################################################################
.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
- $(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+ $(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
--include .depend
+sinclude .depend
#########################################################################
diff --git a/board/mpc8349ads/config.mk b/board/r5200/config.mk
similarity index 81%
copy from board/mpc8349ads/config.mk
copy to board/r5200/config.mk
index 4602169..8fc5319 100644
--- a/board/mpc8349ads/config.mk
+++ b/board/r5200/config.mk
@@ -1,5 +1,7 @@
#
-# Copyright 2004 Freescale Semiconductor, Inc.
+# (C) Copyright 2000-2003
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+# Coldfire contribution by Bernhard Kuhn <bkuhn@metrowerks.com>
#
# See file CREDITS for list of people who contributed to this
# project.
@@ -20,8 +22,4 @@
# MA 02111-1307 USA
#
-#
-# MPC83xxADS
-#
-
-TEXT_BASE = 0xFE700000
+TEXT_BASE = 0x10000000
diff --git a/board/r5200/r5200.c b/board/r5200/r5200.c
new file mode 100644
index 0000000..e51ad25
--- /dev/null
+++ b/board/r5200/r5200.c
@@ -0,0 +1,125 @@
+/*
+ * (C) Copyright 2000-2003
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/m5271.h>
+#include <asm/immap_5271.h>
+
+
+int checkboard (void) {
+ puts ("Board: R5200 Ethernet Module\n");
+ return 0;
+};
+
+long int initdram (int board_type) {
+ int i;
+
+ /*
+ * Set CS2 pin to be SD_CS0
+ */
+ mbar_writeByte(MCF_GPIO_PAR_CS, mbar_readByte(MCF_GPIO_PAR_CS)
+ | MCF_GPIO_PAR_CS_PAR_CS2);
+
+ mbar_writeByte(MCF_GPIO_PAR_SDRAM, mbar_readByte(MCF_GPIO_PAR_SDRAM)
+ | MCF_GPIO_PAR_SDRAM_PAR_CSSDCS(0x01));
+
+ /*
+ * Check to see if the SDRAM has already been initialized
+ * by a run control tool
+ */
+ if (!(mbar_readLong(MCF_SDRAMC_DACR0) & MCF_SDRAMC_DACRn_RE))
+ {
+ /*
+ * Initialize DRAM Control Register: DCR
+ */
+ mbar_writeShort(MCF_SDRAMC_DCR, MCF_SDRAMC_DCR_RTIM(0x01)
+ | MCF_SDRAMC_DCR_RC(0x30));
+
+ /*
+ * Initialize DACR0
+ */
+ mbar_writeLong(MCF_SDRAMC_DACR0,
+ MCF_SDRAMC_DACRn_BA(CFG_SDRAM_BASE>>18)
+ | MCF_SDRAMC_DACRn_CASL(0)
+ | MCF_SDRAMC_DACRn_CBM(3)
+ | MCF_SDRAMC_DACRn_PS(2));
+
+ /*
+ * Initialize DMR0
+ */
+ mbar_writeLong(MCF_SDRAMC_DMR0,
+ MCF_SDRAMC_DMRn_BAM_8M
+ | MCF_SDRAMC_DMRn_V);
+
+ /*
+ * Set IP bit in DACR
+ */
+ mbar_writeLong(MCF_SDRAMC_DACR0, mbar_readLong(MCF_SDRAMC_DACR0)
+ | MCF_SDRAMC_DACRn_IP);
+
+ /*
+ * Wait at least 20ns to allow banks to precharge
+ */
+ for (i = 0; i < 5; i++)
+ asm(" nop");
+
+ /*
+ * Write to this block to initiate precharge
+ */
+ *(u16 *)(CFG_SDRAM_BASE) = 0x9696;
+
+ /*
+ * Set RE bit in DACR
+ */
+ mbar_writeLong(MCF_SDRAMC_DACR0, mbar_readLong(MCF_SDRAMC_DACR0)
+ | MCF_SDRAMC_DACRn_RE);
+
+
+ /*
+ * Wait for at least 8 auto refresh cycles to occur
+ */
+ for (i = 0; i < 2000; i++)
+ asm(" nop");
+
+ /*
+ * Finish the configuration by issuing the MRS.
+ */
+ mbar_writeLong(MCF_SDRAMC_DACR0, mbar_readLong(MCF_SDRAMC_DACR0)
+ | MCF_SDRAMC_DACRn_MRS);
+
+
+ /*
+ * Write to the SDRAM Mode Register
+ */
+ *(u16 *)(CFG_SDRAM_BASE + 0x1000) = 0x9696;
+ }
+
+ return CFG_SDRAM_SIZE * 1024 * 1024;
+};
+
+int testdram (void) {
+ /* TODO: XXX XXX XXX */
+ printf ("DRAM test not implemented!\n");
+
+ return (0);
+}
diff --git a/board/mpc8349ads/u-boot.lds b/board/r5200/u-boot.lds
similarity index 74%
rename from board/mpc8349ads/u-boot.lds
rename to board/r5200/u-boot.lds
index 020cfa6..f7dc070 100644
--- a/board/mpc8349ads/u-boot.lds
+++ b/board/r5200/u-boot.lds
@@ -1,5 +1,6 @@
/*
- * Copyright 2004 Freescale Semiconductor, Inc.
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -20,7 +21,10 @@
* MA 02111-1307 USA
*/
-OUTPUT_ARCH(powerpc)
+OUTPUT_ARCH(m68k)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib);
+/* Do we need any of these for elf?
+ __DYNAMIC = 0; */
SECTIONS
{
/* Read-only sections, merged into text segment: */
@@ -49,34 +53,50 @@
.plt : { *(.plt) }
.text :
{
- cpu/mpc83xx/start.o (.text)
+ /* WARNING - the following is hand-optimized to fit within */
+ /* the sector layout of our flash chips! XXX FIXME XXX */
+
+ cpu/mcf52x2/start.o (.text)
+ lib_m68k/traps.o (.text)
+ cpu/mcf52x2/interrupts.o (.text)
+ common/dlmalloc.o (.text)
+ lib_generic/zlib.o (.text)
+
+ . = DEFINED(env_offset) ? env_offset : .;
+ common/environment.o (.text)
+
*(.text)
*(.fixup)
*(.got1)
- . = ALIGN(16);
+ }
+ _etext = .;
+ PROVIDE (etext = .);
+ .rodata :
+ {
*(.rodata)
*(.rodata1)
- *(.rodata.str1.4)
- *(.eh_frame)
}
.fini : { *(.fini) } =0
.ctors : { *(.ctors) }
.dtors : { *(.dtors) }
/* Read-write section, merged into data segment: */
- . = (. + 0x0FFF) & 0xFFFFF000;
+ . = (. + 0x00FF) & 0xFFFFFF00;
_erotext = .;
PROVIDE (erotext = .);
+
.reloc :
{
+ __got_start = .;
*(.got)
+ __got_end = .;
_GOT2_TABLE_ = .;
*(.got2)
_FIXUP_TABLE_ = .;
*(.fixup)
}
- __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
- __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+ __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+ __fixup_entries = (. - _FIXUP_TABLE_)>>2;
.data :
{
@@ -101,22 +121,24 @@
__ex_table : { *(__ex_table) }
__stop___ex_table = .;
- . = ALIGN(4096);
+ . = ALIGN(256);
__init_begin = .;
.text.init : { *(.text.init) }
.data.init : { *(.data.init) }
- . = ALIGN(4096);
+ . = ALIGN(256);
__init_end = .;
__bss_start = .;
.bss :
{
+ _sbss = .;
*(.sbss) *(.scommon)
*(.dynbss)
*(.bss)
*(COMMON)
+ . = ALIGN(4);
+ _ebss = .;
}
_end = . ;
PROVIDE (end = .);
}
-ENTRY(_start)
diff --git a/board/zylonite/Makefile b/board/zylonite/Makefile
index 999647f..f3ad674 100644
--- a/board/zylonite/Makefile
+++ b/board/zylonite/Makefile
@@ -1,4 +1,3 @@
-
#
# (C) Copyright 2000
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,12 +20,11 @@
# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
# MA 02111-1307 USA
#
-
include $(TOPDIR)/config.mk
LIB = lib$(BOARD).a
-OBJS := zylonite.o flash.o
+OBJS := zylonite.o nand.o
SOBJS := lowlevel_init.o
$(LIB): $(OBJS) $(SOBJS)
diff --git a/board/zylonite/config.mk b/board/zylonite/config.mk
index 09b0f71..b5d5955 100644
--- a/board/zylonite/config.mk
+++ b/board/zylonite/config.mk
@@ -2,3 +2,5 @@
#TEXT_BASE = 0xa1700000
#TEXT_BASE = 0xa3080000
TEXT_BASE = 0xa3008000
+
+BOARDLIBS = drivers/nand/libnand.a
diff --git a/board/zylonite/lowlevel_init.S b/board/zylonite/lowlevel_init.S
index c3bb4eb..da01765 100644
--- a/board/zylonite/lowlevel_init.S
+++ b/board/zylonite/lowlevel_init.S
@@ -235,6 +235,7 @@
orr r1, r1, #0x40000000 @ enable SDRAM for Normal Access
str r1, [r0]
+#ifndef CFG_SKIP_DRAM_SCRUB
/* scrub/init SDRAM if enabled/present */
/* ldr r11, =0xa0000000 /\* base address of SDRAM (CFG_DRAM_BASE) *\/ */
/* ldr r12, =0x04000000 /\* size of memory to scrub (CFG_DRAM_SIZE) *\/ */
@@ -254,6 +255,7 @@
stmia r8!, {r0-r7}
beq 15f
b 10b
+#endif /* CFG_SKIP_DRAM_SCRUB */
15:
/* Mask all interrupts */
diff --git a/board/zylonite/nand.c b/board/zylonite/nand.c
new file mode 100644
index 0000000..5d2cd65
--- /dev/null
+++ b/board/zylonite/nand.c
@@ -0,0 +1,584 @@
+/*
+ * (C) Copyright 2006 DENX Software Engineering
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+#if (CONFIG_COMMANDS & CFG_CMD_NAND)
+#ifdef CONFIG_NEW_NAND_CODE
+
+#include <nand.h>
+#include <asm/arch/pxa-regs.h>
+
+#ifdef CFG_DFC_DEBUG1
+# define DFC_DEBUG1(fmt, args...) printf(fmt, ##args)
+#else
+# define DFC_DEBUG1(fmt, args...)
+#endif
+
+#ifdef CFG_DFC_DEBUG2
+# define DFC_DEBUG2(fmt, args...) printf(fmt, ##args)
+#else
+# define DFC_DEBUG2(fmt, args...)
+#endif
+
+#ifdef CFG_DFC_DEBUG3
+# define DFC_DEBUG3(fmt, args...) printf(fmt, ##args)
+#else
+# define DFC_DEBUG3(fmt, args...)
+#endif
+
+#define MIN(x, y) ((x < y) ? x : y)
+
+/* These really don't belong here, as they are specific to the NAND Model */
+static uint8_t scan_ff_pattern[] = { 0xff, 0xff };
+
+static struct nand_bbt_descr delta_bbt_descr = {
+ .options = 0,
+ .offs = 0,
+ .len = 2,
+ .pattern = scan_ff_pattern
+};
+
+static struct nand_oobinfo delta_oob = {
+ .useecc = MTD_NANDECC_AUTOPL_USR, /* MTD_NANDECC_PLACEONLY, */
+ .eccbytes = 6,
+ .eccpos = {2, 3, 4, 5, 6, 7},
+ .oobfree = { {8, 2}, {12, 4} }
+};
+
+
+/*
+ * not required for Monahans DFC
+ */
+static void dfc_hwcontrol(struct mtd_info *mtdinfo, int cmd)
+{
+ return;
+}
+
+#if 0
+/* read device ready pin */
+static int dfc_device_ready(struct mtd_info *mtdinfo)
+{
+ if(NDSR & NDSR_RDY)
+ return 1;
+ else
+ return 0;
+ return 0;
+}
+#endif
+
+/*
+ * Write buf to the DFC Controller Data Buffer
+ */
+static void dfc_write_buf(struct mtd_info *mtd, const u_char *buf, int len)
+{
+ unsigned long bytes_multi = len & 0xfffffffc;
+ unsigned long rest = len & 0x3;
+ unsigned long *long_buf;
+ int i;
+
+ DFC_DEBUG2("dfc_write_buf: writing %d bytes starting with 0x%x.\n", len, *((unsigned long*) buf));
+ if(bytes_multi) {
+ for(i=0; i<bytes_multi; i+=4) {
+ long_buf = (unsigned long*) &buf[i];
+ NDDB = *long_buf;
+ }
+ }
+ if(rest) {
+ printf("dfc_write_buf: ERROR, writing non 4-byte aligned data.\n");
+ }
+ return;
+}
+
+
+/*
+ * These functions are quite problematic for the DFC. Luckily they are
+ * not used in the current nand code, except for nand_command, which
+ * we've defined our own anyway. The problem is, that we always need
+ * to write 4 bytes to the DFC Data Buffer, but in these functions we
+ * don't know if to buffer the bytes/half words until we've gathered 4
+ * bytes or if to send them straight away.
+ *
+ * Solution: Don't use these with Mona's DFC and complain loudly.
+ */
+static void dfc_write_word(struct mtd_info *mtd, u16 word)
+{
+ printf("dfc_write_word: WARNING, this function does not work with the Monahans DFC!\n");
+}
+static void dfc_write_byte(struct mtd_info *mtd, u_char byte)
+{
+ printf("dfc_write_byte: WARNING, this function does not work with the Monahans DFC!\n");
+}
+
+/* The original:
+ * static void dfc_read_buf(struct mtd_info *mtd, const u_char *buf, int len)
+ *
+ * Shouldn't this be "u_char * const buf" ?
+ */
+static void dfc_read_buf(struct mtd_info *mtd, u_char* const buf, int len)
+{
+ int i=0, j;
+
+ /* we have to be carefull not to overflow the buffer if len is
+ * not a multiple of 4 */
+ unsigned long bytes_multi = len & 0xfffffffc;
+ unsigned long rest = len & 0x3;
+ unsigned long *long_buf;
+
+ DFC_DEBUG3("dfc_read_buf: reading %d bytes.\n", len);
+ /* if there are any, first copy multiple of 4 bytes */
+ if(bytes_multi) {
+ for(i=0; i<bytes_multi; i+=4) {
+ long_buf = (unsigned long*) &buf[i];
+ *long_buf = NDDB;
+ }
+ }
+
+ /* ...then the rest */
+ if(rest) {
+ unsigned long rest_data = NDDB;
+ for(j=0;j<rest; j++)
+ buf[i+j] = (u_char) ((rest_data>>j) & 0xff);
+ }
+
+ return;
+}
+
+/*
+ * read a word. Not implemented as not used in NAND code.
+ */
+static u16 dfc_read_word(struct mtd_info *mtd)
+{
+ printf("dfc_write_byte: UNIMPLEMENTED.\n");
+ return 0;
+}
+
+/* global var, too bad: mk@tbd: move to ->priv pointer */
+static unsigned long read_buf = 0;
+static int bytes_read = -1;
+
+/*
+ * read a byte from NDDB Because we can only read 4 bytes from NDDB at
+ * a time, we buffer the remaining bytes. The buffer is reset when a
+ * new command is sent to the chip.
+ *
+ * WARNING:
+ * This function is currently only used to read status and id
+ * bytes. For these commands always 8 bytes need to be read from
+ * NDDB. So we read and discard these bytes right now. In case this
+ * function is used for anything else in the future, we must check
+ * what was the last command issued and read the appropriate amount of
+ * bytes respectively.
+ */
+static u_char dfc_read_byte(struct mtd_info *mtd)
+{
+ unsigned char byte;
+ unsigned long dummy;
+
+ if(bytes_read < 0) {
+ read_buf = NDDB;
+ dummy = NDDB;
+ bytes_read = 0;
+ }
+ byte = (unsigned char) (read_buf>>(8 * bytes_read++));
+ if(bytes_read >= 4)
+ bytes_read = -1;
+
+ DFC_DEBUG2("dfc_read_byte: byte %u: 0x%x of (0x%x).\n", bytes_read - 1, byte, read_buf);
+ return byte;
+}
+
+/* calculate delta between OSCR values start and now */
+static unsigned long get_delta(unsigned long start)
+{
+ unsigned long cur = OSCR;
+
+ if(cur < start) /* OSCR overflowed */
+ return (cur + (start^0xffffffff));
+ else
+ return (cur - start);
+}
+
+/* delay function, this doesn't belong here */
+static void wait_us(unsigned long us)
+{
+ unsigned long start = OSCR;
+ us *= OSCR_CLK_FREQ;
+
+ while (get_delta(start) < us) {
+ /* do nothing */
+ }
+}
+
+static void dfc_clear_nddb(void)
+{
+ NDCR &= ~NDCR_ND_RUN;
+ wait_us(CFG_NAND_OTHER_TO);
+}
+
+/* wait_event with timeout */
+static unsigned long dfc_wait_event(unsigned long event)
+{
+ unsigned long ndsr, timeout, start = OSCR;
+
+ if(!event)
+ return 0xff000000;
+ else if(event & (NDSR_CS0_CMDD | NDSR_CS0_BBD))
+ timeout = CFG_NAND_PROG_ERASE_TO * OSCR_CLK_FREQ;
+ else
+ timeout = CFG_NAND_OTHER_TO * OSCR_CLK_FREQ;
+
+ while(1) {
+ ndsr = NDSR;
+ if(ndsr & event) {
+ NDSR |= event;
+ break;
+ }
+ if(get_delta(start) > timeout) {
+ DFC_DEBUG1("dfc_wait_event: TIMEOUT waiting for event: 0x%x.\n", event);
+ return 0xff000000;
+ }
+
+ }
+ return ndsr;
+}
+
+/* we don't always wan't to do this */
+static void dfc_new_cmd(void)
+{
+ int retry = 0;
+ unsigned long status;
+
+ while(retry++ <= CFG_NAND_SENDCMD_RETRY) {
+ /* Clear NDSR */
+ NDSR = 0xFFF;
+
+ /* set NDCR[NDRUN] */
+ if(!(NDCR & NDCR_ND_RUN))
+ NDCR |= NDCR_ND_RUN;
+
+ status = dfc_wait_event(NDSR_WRCMDREQ);
+
+ if(status & NDSR_WRCMDREQ)
+ return;
+
+ DFC_DEBUG2("dfc_new_cmd: FAILED to get WRITECMDREQ, retry: %d.\n", retry);
+ dfc_clear_nddb();
+ }
+ DFC_DEBUG1("dfc_new_cmd: giving up after %d retries.\n", retry);
+}
+
+/* this function is called after Programm and Erase Operations to
+ * check for success or failure */
+static int dfc_wait(struct mtd_info *mtd, struct nand_chip *this, int state)
+{
+ unsigned long ndsr=0, event=0;
+
+ if(state == FL_WRITING) {
+ event = NDSR_CS0_CMDD | NDSR_CS0_BBD;
+ } else if(state == FL_ERASING) {
+ event = NDSR_CS0_CMDD | NDSR_CS0_BBD;
+ }
+
+ ndsr = dfc_wait_event(event);
+
+ if((ndsr & NDSR_CS0_BBD) || (ndsr & 0xff000000))
+ return(0x1); /* Status Read error */
+ return 0;
+}
+
+/* cmdfunc send commands to the DFC */
+static void dfc_cmdfunc(struct mtd_info *mtd, unsigned command,
+ int column, int page_addr)
+{
+ /* register struct nand_chip *this = mtd->priv; */
+ unsigned long ndcb0=0, ndcb1=0, ndcb2=0, event=0;
+
+ /* clear the ugly byte read buffer */
+ bytes_read = -1;
+ read_buf = 0;
+
+ switch (command) {
+ case NAND_CMD_READ0:
+ DFC_DEBUG3("dfc_cmdfunc: NAND_CMD_READ0, page_addr: 0x%x, column: 0x%x.\n", page_addr, (column>>1));
+ dfc_new_cmd();
+ ndcb0 = (NAND_CMD_READ0 | (4<<16));
+ column >>= 1; /* adjust for 16 bit bus */
+ ndcb1 = (((column>>1) & 0xff) |
+ ((page_addr<<8) & 0xff00) |
+ ((page_addr<<8) & 0xff0000) |
+ ((page_addr<<8) & 0xff000000)); /* make this 0x01000000 ? */
+ event = NDSR_RDDREQ;
+ goto write_cmd;
+ case NAND_CMD_READ1:
+ DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_READ1 unimplemented!\n");
+ goto end;
+ case NAND_CMD_READOOB:
+ DFC_DEBUG1("dfc_cmdfunc: NAND_CMD_READOOB unimplemented!\n");
+ goto end;
+ case NAND_CMD_READID:
+ dfc_new_cmd();
+ DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_READID.\n");
+ ndcb0 = (NAND_CMD_READID | (3 << 21) | (1 << 16)); /* addr cycles*/
+ event = NDSR_RDDREQ;
+ goto write_cmd;
+ case NAND_CMD_PAGEPROG:
+ /* sent as a multicommand in NAND_CMD_SEQIN */
+ DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_PAGEPROG empty due to multicmd.\n");
+ goto end;
+ case NAND_CMD_ERASE1:
+ DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_ERASE1, page_addr: 0x%x, column: 0x%x.\n", page_addr, (column>>1));
+ dfc_new_cmd();
+ ndcb0 = (0xd060 | (1<<25) | (2<<21) | (1<<19) | (3<<16));
+ ndcb1 = (page_addr & 0x00ffffff);
+ goto write_cmd;
+ case NAND_CMD_ERASE2:
+ DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_ERASE2 empty due to multicmd.\n");
+ goto end;
+ case NAND_CMD_SEQIN:
+ /* send PAGE_PROG command(0x1080) */
+ dfc_new_cmd();
+ DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_SEQIN/PAGE_PROG, page_addr: 0x%x, column: 0x%x.\n", page_addr, (column>>1));
+ ndcb0 = (0x1080 | (1<<25) | (1<<21) | (1<<19) | (4<<16));
+ column >>= 1; /* adjust for 16 bit bus */
+ ndcb1 = (((column>>1) & 0xff) |
+ ((page_addr<<8) & 0xff00) |
+ ((page_addr<<8) & 0xff0000) |
+ ((page_addr<<8) & 0xff000000)); /* make this 0x01000000 ? */
+ event = NDSR_WRDREQ;
+ goto write_cmd;
+ case NAND_CMD_STATUS:
+ DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_STATUS.\n");
+ dfc_new_cmd();
+ ndcb0 = NAND_CMD_STATUS | (4<<21);
+ event = NDSR_RDDREQ;
+ goto write_cmd;
+ case NAND_CMD_RESET:
+ DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_RESET.\n");
+ ndcb0 = NAND_CMD_RESET | (5<<21);
+ event = NDSR_CS0_CMDD;
+ goto write_cmd;
+ default:
+ printk("dfc_cmdfunc: error, unsupported command.\n");
+ goto end;
+ }
+
+ write_cmd:
+ NDCB0 = ndcb0;
+ NDCB0 = ndcb1;
+ NDCB0 = ndcb2;
+
+ /* wait_event: */
+ dfc_wait_event(event);
+ end:
+ return;
+}
+
+static void dfc_gpio_init(void)
+{
+ DFC_DEBUG2("Setting up DFC GPIO's.\n");
+
+ /* no idea what is done here, see zylonite.c */
+ GPIO4 = 0x1;
+
+ DF_ALE_WE1 = 0x00000001;
+ DF_ALE_WE2 = 0x00000001;
+ DF_nCS0 = 0x00000001;
+ DF_nCS1 = 0x00000001;
+ DF_nWE = 0x00000001;
+ DF_nRE = 0x00000001;
+ DF_IO0 = 0x00000001;
+ DF_IO8 = 0x00000001;
+ DF_IO1 = 0x00000001;
+ DF_IO9 = 0x00000001;
+ DF_IO2 = 0x00000001;
+ DF_IO10 = 0x00000001;
+ DF_IO3 = 0x00000001;
+ DF_IO11 = 0x00000001;
+ DF_IO4 = 0x00000001;
+ DF_IO12 = 0x00000001;
+ DF_IO5 = 0x00000001;
+ DF_IO13 = 0x00000001;
+ DF_IO6 = 0x00000001;
+ DF_IO14 = 0x00000001;
+ DF_IO7 = 0x00000001;
+ DF_IO15 = 0x00000001;
+
+ DF_nWE = 0x1901;
+ DF_nRE = 0x1901;
+ DF_CLE_NOE = 0x1900;
+ DF_ALE_WE1 = 0x1901;
+ DF_INT_RnB = 0x1900;
+}
+
+/*
+ * Board-specific NAND initialization. The following members of the
+ * argument are board-specific (per include/linux/mtd/nand_new.h):
+ * - IO_ADDR_R?: address to read the 8 I/O lines of the flash device
+ * - IO_ADDR_W?: address to write the 8 I/O lines of the flash device
+ * - hwcontrol: hardwarespecific function for accesing control-lines
+ * - dev_ready: hardwarespecific function for accesing device ready/busy line
+ * - enable_hwecc?: function to enable (reset) hardware ecc generator. Must
+ * only be provided if a hardware ECC is available
+ * - eccmode: mode of ecc, see defines
+ * - chip_delay: chip dependent delay for transfering data from array to
+ * read regs (tR)
+ * - options: various chip options. They can partly be set to inform
+ * nand_scan about special functionality. See the defines for further
+ * explanation
+ * Members with a "?" were not set in the merged testing-NAND branch,
+ * so they are not set here either.
+ */
+void board_nand_init(struct nand_chip *nand)
+{
+ unsigned long tCH, tCS, tWH, tWP, tRH, tRP, tRP_high, tR, tWHR, tAR;
+
+ /* set up GPIO Control Registers */
+ dfc_gpio_init();
+
+ /* turn on the NAND Controller Clock (104 MHz @ D0) */
+ CKENA |= (CKENA_4_NAND | CKENA_9_SMC);
+
+#undef CFG_TIMING_TIGHT
+#ifndef CFG_TIMING_TIGHT
+ tCH = MIN(((unsigned long) (NAND_TIMING_tCH * DFC_CLK_PER_US) + 1),
+ DFC_MAX_tCH);
+ tCS = MIN(((unsigned long) (NAND_TIMING_tCS * DFC_CLK_PER_US) + 1),
+ DFC_MAX_tCS);
+ tWH = MIN(((unsigned long) (NAND_TIMING_tWH * DFC_CLK_PER_US) + 1),
+ DFC_MAX_tWH);
+ tWP = MIN(((unsigned long) (NAND_TIMING_tWP * DFC_CLK_PER_US) + 1),
+ DFC_MAX_tWP);
+ tRH = MIN(((unsigned long) (NAND_TIMING_tRH * DFC_CLK_PER_US) + 1),
+ DFC_MAX_tRH);
+ tRP = MIN(((unsigned long) (NAND_TIMING_tRP * DFC_CLK_PER_US) + 1),
+ DFC_MAX_tRP);
+ tR = MIN(((unsigned long) (NAND_TIMING_tR * DFC_CLK_PER_US) + 1),
+ DFC_MAX_tR);
+ tWHR = MIN(((unsigned long) (NAND_TIMING_tWHR * DFC_CLK_PER_US) + 1),
+ DFC_MAX_tWHR);
+ tAR = MIN(((unsigned long) (NAND_TIMING_tAR * DFC_CLK_PER_US) + 1),
+ DFC_MAX_tAR);
+#else /* this is the tight timing */
+
+ tCH = MIN(((unsigned long) (NAND_TIMING_tCH * DFC_CLK_PER_US)),
+ DFC_MAX_tCH);
+ tCS = MIN(((unsigned long) (NAND_TIMING_tCS * DFC_CLK_PER_US)),
+ DFC_MAX_tCS);
+ tWH = MIN(((unsigned long) (NAND_TIMING_tWH * DFC_CLK_PER_US)),
+ DFC_MAX_tWH);
+ tWP = MIN(((unsigned long) (NAND_TIMING_tWP * DFC_CLK_PER_US)),
+ DFC_MAX_tWP);
+ tRH = MIN(((unsigned long) (NAND_TIMING_tRH * DFC_CLK_PER_US)),
+ DFC_MAX_tRH);
+ tRP = MIN(((unsigned long) (NAND_TIMING_tRP * DFC_CLK_PER_US)),
+ DFC_MAX_tRP);
+ tR = MIN(((unsigned long) (NAND_TIMING_tR * DFC_CLK_PER_US) - tCH - 2),
+ DFC_MAX_tR);
+ tWHR = MIN(((unsigned long) (NAND_TIMING_tWHR * DFC_CLK_PER_US) - tCH - 2),
+ DFC_MAX_tWHR);
+ tAR = MIN(((unsigned long) (NAND_TIMING_tAR * DFC_CLK_PER_US) - 2),
+ DFC_MAX_tAR);
+#endif /* CFG_TIMING_TIGHT */
+
+
+ DFC_DEBUG2("tCH=%u, tCS=%u, tWH=%u, tWP=%u, tRH=%u, tRP=%u, tR=%u, tWHR=%u, tAR=%u.\n", tCH, tCS, tWH, tWP, tRH, tRP, tR, tWHR, tAR);
+
+ /* tRP value is split in the register */
+ if(tRP & (1 << 4)) {
+ tRP_high = 1;
+ tRP &= ~(1 << 4);
+ } else {
+ tRP_high = 0;
+ }
+
+ NDTR0CS0 = (tCH << 19) |
+ (tCS << 16) |
+ (tWH << 11) |
+ (tWP << 8) |
+ (tRP_high << 6) |
+ (tRH << 3) |
+ (tRP << 0);
+
+ NDTR1CS0 = (tR << 16) |
+ (tWHR << 4) |
+ (tAR << 0);
+
+ /* If it doesn't work (unlikely) think about:
+ * - ecc enable
+ * - chip select don't care
+ * - read id byte count
+ *
+ * Intentionally enabled by not setting bits:
+ * - dma (DMA_EN)
+ * - page size = 512
+ * - cs don't care, see if we can enable later!
+ * - row address start position (after second cycle)
+ * - pages per block = 32
+ * - ND_RDY : clears command buffer
+ */
+ /* NDCR_NCSX | /\* Chip select busy don't care *\/ */
+
+ NDCR = (NDCR_SPARE_EN | /* use the spare area */
+ NDCR_DWIDTH_C | /* 16bit DFC data bus width */
+ NDCR_DWIDTH_M | /* 16 bit Flash device data bus width */
+ (2 << 16) | /* read id count = 7 ???? mk@tbd */
+ NDCR_ND_ARB_EN | /* enable bus arbiter */
+ NDCR_RDYM | /* flash device ready ir masked */
+ NDCR_CS0_PAGEDM | /* ND_nCSx page done ir masked */
+ NDCR_CS1_PAGEDM |
+ NDCR_CS0_CMDDM | /* ND_CSx command done ir masked */
+ NDCR_CS1_CMDDM |
+ NDCR_CS0_BBDM | /* ND_CSx bad block detect ir masked */
+ NDCR_CS1_BBDM |
+ NDCR_DBERRM | /* double bit error ir masked */
+ NDCR_SBERRM | /* single bit error ir masked */
+ NDCR_WRDREQM | /* write data request ir masked */
+ NDCR_RDDREQM | /* read data request ir masked */
+ NDCR_WRCMDREQM); /* write command request ir masked */
+
+
+ /* wait 10 us due to cmd buffer clear reset */
+ /* wait(10); */
+
+
+ nand->hwcontrol = dfc_hwcontrol;
+/* nand->dev_ready = dfc_device_ready; */
+ nand->eccmode = NAND_ECC_SOFT;
+ nand->options = NAND_BUSWIDTH_16;
+ nand->waitfunc = dfc_wait;
+ nand->read_byte = dfc_read_byte;
+ nand->write_byte = dfc_write_byte;
+ nand->read_word = dfc_read_word;
+ nand->write_word = dfc_write_word;
+ nand->read_buf = dfc_read_buf;
+ nand->write_buf = dfc_write_buf;
+
+ nand->cmdfunc = dfc_cmdfunc;
+ nand->autooob = &delta_oob;
+ nand->badblock_pattern = &delta_bbt_descr;
+}
+
+#else
+ #error "U-Boot legacy NAND support not available for Monahans DFC."
+#endif
+#endif
diff --git a/common/cmd_load.c b/common/cmd_load.c
index 2432ee2..f63b8e8 100644
--- a/common/cmd_load.c
+++ b/common/cmd_load.c
@@ -33,9 +33,12 @@
DECLARE_GLOBAL_DATA_PTR;
+#if (CONFIG_COMMANDS & CFG_CMD_LOADB)
+static ulong load_serial_ymodem (ulong offset);
+#endif
+
#if (CONFIG_COMMANDS & CFG_CMD_LOADS)
static ulong load_serial (ulong offset);
-static ulong load_serial_ymodem (ulong offset);
static int read_record (char *buf, ulong len);
# if (CONFIG_COMMANDS & CFG_CMD_SAVES)
static int save_serial (ulong offset, ulong size);
diff --git a/common/environment.c b/common/environment.c
index c7f54c6..81471ce 100644
--- a/common/environment.c
+++ b/common/environment.c
@@ -59,7 +59,8 @@
defined(CONFIG_TQM8xxL) || \
defined(CONFIG_RRVISION) || \
defined(CONFIG_TRAB) || \
- defined(CONFIG_PPCHAMELEONEVB) ) && \
+ defined(CONFIG_PPCHAMELEONEVB) || \
+ defined(CONFIG_M5271EVB)) && \
defined(ENV_CRC) /* Environment embedded in U-Boot .ppcenv section */
/* XXX - This only works with GNU C */
# define __PPCENV__ __attribute__ ((section(".ppcenv")))
diff --git a/config.mk b/config.mk
index dfbb1b7..b1e1d8f 100644
--- a/config.mk
+++ b/config.mk
@@ -143,7 +143,14 @@
endif
endif
+# turn jbsr into jsr for m68k
+ifeq ($(ARCH),m68k)
+ifeq ($(findstring 3.4,$(shell $(CC) --version)),3.4)
+AFLAGS_DEBUG := -Wa,-gstabs,-S
+endif
+else
AFLAGS_DEBUG := -Wa,-gstabs
+endif
AFLAGS := $(AFLAGS_DEBUG) -D__ASSEMBLY__ $(CPPFLAGS)
LDFLAGS += -Bstatic -T $(LDSCRIPT) -Ttext $(TEXT_BASE) $(PLATFORM_LDFLAGS)
diff --git a/cpu/mcf52x2/cpu.c b/cpu/mcf52x2/cpu.c
index 32a524f..e6e5d9b 100644
--- a/cpu/mcf52x2/cpu.c
+++ b/cpu/mcf52x2/cpu.c
@@ -25,6 +25,11 @@
#include <watchdog.h>
#include <command.h>
+#ifdef CONFIG_M5271
+#include <asm/immap_5271.h>
+#include <asm/m5271.h>
+#endif
+
#ifdef CONFIG_M5272
#include <asm/immap_5272.h>
#include <asm/m5272.h>
@@ -38,6 +43,42 @@
#include <asm/m5249.h>
#endif
+#ifdef CONFIG_M5271
+int checkcpu (void)
+{
+ char buf[32];
+
+ printf ("CPU: Freescale Coldfire MCF5271 at %s MHz\n", strmhz(buf, CFG_CLK));
+ return 0;
+}
+
+int do_reset (cmd_tbl_t *cmdtp, bd_t *bd, int flag, int argc, char *argv[]) {
+ mbar_writeByte(MCF_RCM_RCR,
+ MCF_RCM_RCR_SOFTRST | MCF_RCM_RCR_FRCRSTOUT);
+ return 0;
+};
+
+#if defined(CONFIG_WATCHDOG)
+void watchdog_reset (void)
+{
+ mbar_writeShort(MCF_WTM_WSR, 0x5555);
+ mbar_writeShort(MCF_WTM_WSR, 0xAAAA);
+}
+
+int watchdog_disable (void)
+{
+ mbar_writeShort(MCF_WTM_WCR, 0);
+ return (0);
+}
+
+int watchdog_init (void)
+{
+ mbar_writeShort(MCF_WTM_WCR, MCF_WTM_WCR_EN);
+ return (0);
+}
+#endif /* #ifdef CONFIG_WATCHDOG */
+
+#endif
#ifdef CONFIG_M5272
int do_reset (cmd_tbl_t *cmdtp, bd_t *bd, int flag, int argc, char *argv[]) {
@@ -66,12 +107,12 @@
case 0x4: suf = "3K75N"; break;
default:
suf = NULL;
- printf ("MOTOROLA MCF5272 (Mask:%01x)\n", msk);
+ printf ("Freescale MCF5272 (Mask:%01x)\n", msk);
break;
}
if (suf)
- printf ("MOTOROLA MCF5272 %s\n", suf);
+ printf ("Freescale MCF5272 %s\n", suf);
return 0;
};
@@ -117,7 +158,7 @@
#ifdef CONFIG_M5282
int checkcpu (void)
{
- puts ("CPU: MOTOROLA Coldfire MCF5282\n");
+ puts ("CPU: Freescale Coldfire MCF5282\n");
return 0;
}
@@ -131,7 +172,7 @@
{
char buf[32];
- printf ("CPU: MOTOROLA Coldfire MCF5249 at %s MHz\n", strmhz(buf, CFG_CLK));
+ printf ("CPU: Freescale Coldfire MCF5249 at %s MHz\n", strmhz(buf, CFG_CLK));
return 0;
}
diff --git a/cpu/mcf52x2/cpu_init.c b/cpu/mcf52x2/cpu_init.c
index 350c431..d33adc2 100644
--- a/cpu/mcf52x2/cpu_init.c
+++ b/cpu/mcf52x2/cpu_init.c
@@ -24,6 +24,11 @@
#include <common.h>
#include <watchdog.h>
+#ifdef CONFIG_M5271
+#include <asm/m5271.h>
+#include <asm/immap_5271.h>
+#endif
+
#ifdef CONFIG_M5272
#include <asm/m5272.h>
#include <asm/immap_5272.h>
@@ -38,6 +43,38 @@
#include <asm/m5249.h>
#endif
+#if defined(CONFIG_M5271)
+void cpu_init_f (void)
+{
+#ifndef CONFIG_WATCHDOG
+ /* Disable the watchdog if we aren't using it */
+ mbar_writeShort(MCF_WTM_WCR, 0);
+#endif
+
+ /* Set clockspeed to 100MHz */
+ mbar_writeShort(MCF_FMPLL_SYNCR,
+ MCF_FMPLL_SYNCR_MFD(0) | MCF_FMPLL_SYNCR_RFD(0));
+ while (!mbar_readByte(MCF_FMPLL_SYNSR) & MCF_FMPLL_SYNSR_LOCK);
+
+ /* Enable UART pins */
+ mbar_writeShort(MCF_GPIO_PAR_UART, MCF_GPIO_PAR_UART_U0TXD |
+ MCF_GPIO_PAR_UART_U0RXD |
+ MCF_GPIO_PAR_UART_U1RXD_UART1 |
+ MCF_GPIO_PAR_UART_U1TXD_UART1);
+
+ /* Enable Ethernet pins */
+ mbar_writeByte(MCF_GPIO_PAR_FECI2C, CFG_FECI2C);
+}
+
+/*
+ * initialize higher level parts of CPU like timers
+ */
+int cpu_init_r (void)
+{
+ return (0);
+}
+#endif
+
#if defined(CONFIG_M5272)
/*
* Breath some life into the CPU...
diff --git a/cpu/mcf52x2/fec.c b/cpu/mcf52x2/fec.c
index a5c50af..f207dd6 100644
--- a/cpu/mcf52x2/fec.c
+++ b/cpu/mcf52x2/fec.c
@@ -25,6 +25,11 @@
#include <malloc.h>
#include <asm/fec.h>
+#ifdef CONFIG_M5271
+#include <asm/m5271.h>
+#include <asm/immap_5271.h>
+#endif
+
#ifdef CONFIG_M5272
#include <asm/m5272.h>
#include <asm/immap_5272.h>
@@ -41,7 +46,7 @@
#ifdef CONFIG_M5272
#define FEC_ADDR (CFG_MBAR + 0x840)
#endif
-#ifdef CONFIG_M5282
+#if defined(CONFIG_M5282) || defined(CONFIG_M5271)
#define FEC_ADDR (CFG_MBAR + 0x1000)
#endif
@@ -240,10 +245,22 @@
#endif
#undef ea
+#ifdef CONFIG_M5271
+ /* Clear multicast address hash table
+ */
+ fecp->fec_ghash_table_high = 0;
+ fecp->fec_ghash_table_low = 0;
+
+ /* Clear individual address hash table
+ */
+ fecp->fec_ihash_table_high = 0;
+ fecp->fec_ihash_table_low = 0;
+#else
/* Clear multicast address hash table
*/
fecp->fec_hash_table_high = 0;
fecp->fec_hash_table_low = 0;
+#endif
/* Set maximum receive buffer size.
*/
@@ -295,6 +312,9 @@
fecp->fec_x_cntrl = FEC_TCNTRL_FDEN;
#else /* Half duplex mode */
fecp->fec_r_cntrl = FEC_RCNTRL_MII_MODE | FEC_RCNTRL_DRT;
+#ifdef CONFIG_M5271
+ fecp->fec_r_cntrl |= (PKT_MAXBUF_SIZE << 16); /* set max frame length */
+#endif
fecp->fec_x_cntrl = 0;
#endif
/* Set MII speed */
diff --git a/cpu/mcf52x2/interrupts.c b/cpu/mcf52x2/interrupts.c
index 868df39..116747a 100644
--- a/cpu/mcf52x2/interrupts.c
+++ b/cpu/mcf52x2/interrupts.c
@@ -27,6 +27,11 @@
#include <watchdog.h>
#include <asm/processor.h>
+#ifdef CONFIG_M5271
+#include <asm/m5271.h>
+#include <asm/immap_5271.h>
+#endif
+
#ifdef CONFIG_M5272
#include <asm/m5272.h>
#include <asm/immap_5272.h>
@@ -171,7 +176,7 @@
}
#endif
-#ifdef CONFIG_M5282
+#if defined(CONFIG_M5282) || defined(CONFIG_M5271)
int interrupt_init (void)
{
return 0;
diff --git a/cpu/mcf52x2/serial.c b/cpu/mcf52x2/serial.c
index 79628d0..c66bdef 100644
--- a/cpu/mcf52x2/serial.c
+++ b/cpu/mcf52x2/serial.c
@@ -23,9 +23,14 @@
#include <common.h>
#include <command.h>
+#include <watchdog.h>
#include <asm/mcfuart.h>
+#ifdef CONFIG_M5271
+#include <asm/m5271.h>
+#endif
+
#ifdef CONFIG_M5272
#include <asm/m5272.h>
#endif
@@ -40,7 +45,7 @@
DECLARE_GLOBAL_DATA_PTR;
-#ifdef CONFIG_M5249
+#if defined(CONFIG_M5249) || defined(CONFIG_M5271)
#define DoubleClock(a) ((double)(CFG_CLK/2) / 32.0 / (double)(a))
#else
#define DoubleClock(a) ((double)(CFG_CLK) / 32.0 / (double)(a))
@@ -48,9 +53,12 @@
void rs_serial_setbaudrate(int port,int baudrate)
{
-#if defined(CONFIG_M5272) || defined(CONFIG_M5249)
+#if defined(CONFIG_M5272) || defined(CONFIG_M5249) || defined(CONFIG_M5271)
volatile unsigned char *uartp;
- double clock, fraction;
+#ifndef CONFIG_M5271
+ double fraction;
+#endif
+ double clock;
if (port == 0)
uartp = (volatile unsigned char *) (CFG_MBAR + MCFUART_BASE1);
@@ -59,12 +67,14 @@
clock = DoubleClock(baudrate); /* Set baud above */
- fraction = ((clock - (int)clock) * 16.0) + 0.5;
-
uartp[MCFUART_UBG1] = (((int)clock >> 8) & 0xff); /* set msb baud */
uartp[MCFUART_UBG2] = ((int)clock & 0xff); /* set lsb baud */
+
+#ifndef CONFIG_M5271
+ fraction = ((clock - (int)clock) * 16.0) + 0.5;
uartp[MCFUART_UFPD] = ((int)fraction & 0xf); /* set baud fraction adjust */
#endif
+#endif
};
void rs_serial_init(int port,int baudrate)
@@ -79,8 +89,9 @@
else
uartp = (volatile unsigned char *) (CFG_MBAR + MCFUART_BASE2);
- uartp[MCFUART_UCR] = MCFUART_UCR_CMDRESETRX; /* reset RX */
uartp[MCFUART_UCR] = MCFUART_UCR_CMDRESETTX; /* reset TX */
+ uartp[MCFUART_UCR] = MCFUART_UCR_CMDRESETRX; /* reset RX */
+
uartp[MCFUART_UCR] = MCFUART_UCR_CMDRESETMRPTR; /* reset MR pointer */
uartp[MCFUART_UCR] = MCFUART_UCR_CMDRESETERR; /* reset Error pointer */
@@ -90,9 +101,15 @@
uartp[MCFUART_UMR] = MCFUART_MR1_PARITYNONE | MCFUART_MR1_CS8;
uartp[MCFUART_UMR] = MCFUART_MR2_STOP1;
+ /* Mask UART interrupts */
+ uartp[MCFUART_UIMR] = 0;
+
+ /* Set clock Select Register: Tx/Rx clock is timer */
+ uartp[MCFUART_UCSR] = MCFUART_UCSR_RXCLKTIMER | MCFUART_UCSR_TXCLKTIMER;
+
rs_serial_setbaudrate(port,baudrate);
- uartp[MCFUART_UCSR] = MCFUART_UCSR_RXCLKTIMER | MCFUART_UCSR_TXCLKTIMER;
+ /* Enable Tx/Rx */
uartp[MCFUART_UCR] = MCFUART_UCR_RXENABLE | MCFUART_UCR_TXENABLE;
return;
@@ -158,7 +175,9 @@
}
int serial_getc(void) {
- while(!rs_is_char());
+ while(!rs_is_char())
+ WATCHDOG_RESET();
+
return rs_get_char();
}
diff --git a/cpu/mcf52x2/start.S b/cpu/mcf52x2/start.S
index b4926e2..3ab812b 100644
--- a/cpu/mcf52x2/start.S
+++ b/cpu/mcf52x2/start.S
@@ -55,7 +55,11 @@
*/
_vectors:
+#ifndef CONFIG_R5200
.long 0x00000000, _START
+#else
+.long 0x00000000, 0x400 /* Flash offset is 0 until we setup CS0 */
+#endif
.long _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
.long _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
.long _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
@@ -124,26 +128,42 @@
movec %d0, %RAMBAR0
#endif /* #if defined(CONFIG_M5272) || defined(CONFIG_M5249) */
-#ifdef CONFIG_M5282
+#if defined(CONFIG_M5282) || defined(CONFIG_M5271)
/* Initialize IPSBAR */
move.l #(CFG_MBAR + 1), %d0 /* set IPSBAR address + valid flag */
move.l %d0, 0x40000000
+#ifdef CONFIG_M5282
/* Initialize FLASHBAR: locate internal Flash and validate it */
move.l #(CFG_INT_FLASH_BASE + 0x21), %d0
movec %d0, %RAMBAR0
+#endif
/* Initialize RAMBAR1: locate SRAM and validate it */
move.l #(CFG_INIT_RAM_ADDR + 0x21), %d0
movec %d0, %RAMBAR1
#endif
+#ifdef CONFIG_R5200
+ move.l #(_flash_setup-CFG_FLASH_BASE), %a0
+ move.l #(_flash_setup_end-CFG_FLASH_BASE), %a1
+ move.l #(CFG_INIT_RAM_ADDR), %a2
+_copy_flash:
+ move.l (%a0)+, (%a2)+
+ cmp.l %a0, %a1
+ bgt.s _copy_flash
+ jmp CFG_INIT_RAM_ADDR
+_after_flash_copy:
+#endif
+
+#if 0
/* invalidate and disable cache */
move.l #0x01000000, %d0 /* Invalidate cache cmd */
movec %d0, %CACR /* Invalidate cache */
move.l #0, %d0
movec %d0, %ACR0
movec %d0, %ACR1
+#endif
/* set stackpointer to end of internal ram to get some stackspace for the first c-code */
move.l #(CFG_INIT_RAM_ADDR + CFG_INIT_SP_OFFSET), %sp
@@ -154,10 +174,28 @@
bsr cpu_init_f /* run low-level CPU init code (from flash) */
bsr board_init_f /* run low-level board init code (from flash) */
- /* board_init_f() does not return
+ /* board_init_f() does not return */
/*------------------------------------------------------------------------------*/
+#ifdef CONFIG_R5200
+_flash_setup:
+ /* CSAR0 */
+ move.l #((CFG_FLASH_BASE & 0xffff0000) >> 16), %d0
+ move.w %d0, 0x40000080
+
+ /* CSCR0 */
+ move.l #0x2180, %d0 /* 8 wait states, 16bit port, auto ack, */
+ move.w %d0, 0x4000008A
+
+ /* CSMR0 */
+ move.l #0x001f0001, %d0 /* 2 MB, valid */
+ move.l %d0, 0x40000084
+
+ jmp _after_flash_copy.L
+_flash_setup_end:
+#endif
+
/*
* void relocate_code (addr_sp, gd, addr_moni)
*
diff --git a/cpu/mpc83xx/i2c.c b/cpu/mpc83xx/i2c.c
index 4e70f80..70450f9 100644
--- a/cpu/mpc83xx/i2c.c
+++ b/cpu/mpc83xx/i2c.c
@@ -41,7 +41,7 @@
#include <i2c.h>
#include <asm/i2c.h>
-#if defined(CONFIG_MPC8349ADS) || defined(CONFIG_TQM834X)
+#if defined(CONFIG_MPC8349EMDS) || defined(CONFIG_TQM834X)
i2c_t * mpc8349_i2c = (i2c_t*)(CFG_IMMRBAR + CFG_I2C_OFFSET);
#endif
diff --git a/drivers/cfi_flash.c b/drivers/cfi_flash.c
index 2e37480..3717237 100644
--- a/drivers/cfi_flash.c
+++ b/drivers/cfi_flash.c
@@ -45,6 +45,7 @@
/* #define DEBUG */
#include <common.h>
+#include <watchdog.h>
#include <asm/processor.h>
#include <asm/byteorder.h>
#include <environment.h>
@@ -1307,6 +1308,10 @@
if (flag)
enable_interrupts ();
+#if defined(CONFIG_MCF52x2)
+ WATCHDOG_RESET();
+#endif
+
return flash_full_status_check (info, find_sector (info, dest),
info->write_tout, "write");
}
diff --git a/examples/Makefile b/examples/Makefile
index fee2674..b198048 100644
--- a/examples/Makefile
+++ b/examples/Makefile
@@ -122,7 +122,7 @@
CPPFLAGS += -I..
-all: .depend $(OBJS) $(LIB) $(SREC) $(BIN)
+all: .depend $(OBJS) $(LIB) #$(SREC) $(BIN)
#########################################################################
$(LIB): .depend $(LIBOBJS)
diff --git a/include/asm-m68k/immap_5271.h b/include/asm-m68k/immap_5271.h
new file mode 100644
index 0000000..424dc1d
--- /dev/null
+++ b/include/asm-m68k/immap_5271.h
@@ -0,0 +1,98 @@
+/*
+ * MCF5272 Internal Memory Map
+ *
+ * Copyright (c) 2003 Josef Baumgartner <josef.baumgartner@telex.de>
+ * 2006 Zachary P. Landau <zachary.landau@labxtechnologies.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __IMMAP_5271__
+#define __IMMAP_5271__
+
+/* Interrupt module registers
+*/
+typedef struct int_ctrl {
+ uint int_icr1;
+ uint int_icr2;
+ uint int_icr3;
+ uint int_icr4;
+ uint int_isr;
+ uint int_pitr;
+ uint int_piwr;
+ uchar res1[3];
+ uchar int_pivr;
+} intctrl_t;
+
+/* Timer module registers
+ */
+typedef struct timer_ctrl {
+ ushort timer_tmr;
+ ushort res1;
+ ushort timer_trr;
+ ushort res2;
+ ushort timer_tcap;
+ ushort res3;
+ ushort timer_tcn;
+ ushort res4;
+ ushort timer_ter;
+ uchar res5[14];
+} timer_t;
+
+ /* Fast ethernet controller registers
+ */
+typedef struct fec {
+ uint res1;
+ uint fec_ievent;
+ uint fec_imask;
+ uint res2;
+ uint fec_r_des_active;
+ uint fec_x_des_active;
+ uint res3[3];
+ uint fec_ecntrl;
+ uint res4[6];
+ uint fec_mii_data;
+ uint fec_mii_speed;
+ uint res5[7];
+ uint fec_mibc;
+ uint res6[7];
+ uint fec_r_cntrl;
+ uint res7[15];
+ uint fec_x_cntrl;
+ uint res8[7];
+ uint fec_addr_low;
+ uint fec_addr_high;
+ uint fec_opd;
+ uint res9[10];
+ uint fec_ihash_table_high;
+ uint fec_ihash_table_low;
+ uint fec_ghash_table_high;
+ uint fec_ghash_table_low;
+ uint res10[7];
+ uint fec_tfwr;
+ uint res11;
+ uint fec_r_bound;
+ uint fec_r_fstart;
+ uint res12[11];
+ uint fec_r_des_start;
+ uint fec_x_des_start;
+ uint fec_r_buff_size;
+} fec_t;
+
+#endif /* __IMMAP_5271__ */
diff --git a/include/asm-m68k/m5271.h b/include/asm-m68k/m5271.h
new file mode 100644
index 0000000..765414f
--- /dev/null
+++ b/include/asm-m68k/m5271.h
@@ -0,0 +1,114 @@
+/*
+ * mcf5271.h -- Definitions for Motorola Coldfire 5271
+ *
+ * (C) Copyright 2006, Lab X Technologies <zachary.landau@labxtechnologies.com>
+ * Based on mcf5272sim.h of uCLinux distribution:
+ * (C) Copyright 1999, Greg Ungerer (gerg@snapgear.com)
+ * (C) Copyright 2000, Lineo Inc. (www.lineo.com)
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+
+#ifndef _MCF5271_H_
+#define _MCF5271_H_
+
+#define mbar_readLong(x) *((volatile unsigned long *) (CFG_MBAR + x))
+#define mbar_readShort(x) *((volatile unsigned short *) (CFG_MBAR + x))
+#define mbar_readByte(x) *((volatile unsigned char *) (CFG_MBAR + x))
+#define mbar_writeLong(x,y) *((volatile unsigned long *) (CFG_MBAR + x)) = y
+#define mbar_writeShort(x,y) *((volatile unsigned short *) (CFG_MBAR + x)) = y
+#define mbar_writeByte(x,y) *((volatile unsigned char *) (CFG_MBAR + x)) = y
+
+#define MCF_FMPLL_SYNCR 0x120000
+#define MCF_FMPLL_SYNSR 0x120004
+#define MCF_FMPLL_SYNCR_MFD(x) ((x&0x7)<<24)
+#define MCF_FMPLL_SYNCR_RFD(x) ((x&0x7)<<19)
+#define MCF_FMPLL_SYNSR_LOCK 0x8
+
+#define MCF_WTM_WCR 0x140000
+#define MCF_WTM_WCNTR 0x140004
+#define MCF_WTM_WSR 0x140006
+#define MCF_WTM_WCR_EN 0x0001
+
+#define MCF_RCM_RCR 0x110000
+#define MCF_RCM_RCR_FRCRSTOUT 0x40
+#define MCF_RCM_RCR_SOFTRST 0x80
+
+#define MCF_GPIO_PAR_AD 0x100040
+#define MCF_GPIO_PAR_CS 0x100045
+#define MCF_GPIO_PAR_SDRAM 0x100046
+#define MCF_GPIO_PAR_FECI2C 0x100047
+#define MCF_GPIO_PAR_UART 0x100048
+
+#define MCF_GPIO_AD_ADDR23 0x80
+#define MCF_GPIO_AD_ADDR22 0x40
+#define MCF_GPIO_AD_ADDR21 0x20
+#define MCF_GPIO_AD_DATAL 0x01
+#define MCF_GPIO_AD_MASK 0xe1
+
+#define MCF_GPIO_PAR_CS_PAR_CS2 0x04
+
+#define MCF_GPIO_SDRAM_CSSDCS_00 0x00 /* CS[3:2] pins: CS3, CS2 */
+#define MCF_GPIO_SDRAM_CSSDCS_01 0x40 /* CS[3:2] pins: CS3, SD_CS0 */
+#define MCF_GPIO_SDRAM_CSSDCS_10 0x80 /* CS[3:2] pins: SD_CS1, SC2 */
+#define MCF_GPIO_SDRAM_CSSDCS_11 0xc0 /* CS[3:2] pins: SD_CS1, SD_CS0 */
+#define MCF_GPIO_SDRAM_SDWE 0x20 /* WE pin */
+#define MCF_GPIO_SDRAM_SCAS 0x10 /* CAS pin */
+#define MCF_GPIO_SDRAM_SRAS 0x08 /* RAS pin */
+#define MCF_GPIO_SDRAM_SCKE 0x04 /* CKE pin */
+#define MCF_GPIO_SDRAM_SDCS_00 0x00 /* SD_CS[0:1] pins: GPIO, GPIO */
+#define MCF_GPIO_SDRAM_SDCS_01 0x01 /* SD_CS[0:1] pins: GPIO, SD_CS0 */
+#define MCF_GPIO_SDRAM_SDCS_10 0x02 /* SD_CS[0:1] pins: SD_CS1, GPIO */
+#define MCF_GPIO_SDRAM_SDCS_11 0x03 /* SD_CS[0:1] pins: SD_CS1, SD_CS0 */
+
+#define MCF_GPIO_PAR_UART_U0RTS 0x0001
+#define MCF_GPIO_PAR_UART_U0CTS 0x0002
+#define MCF_GPIO_PAR_UART_U0TXD 0x0004
+#define MCF_GPIO_PAR_UART_U0RXD 0x0008
+#define MCF_GPIO_PAR_UART_U1RXD_UART1 0x0C00
+#define MCF_GPIO_PAR_UART_U1TXD_UART1 0x0300
+
+#define MCF_GPIO_PAR_SDRAM_PAR_CSSDCS(x) (((x)&0x03)<<6)
+
+#define MCF_SDRAMC_DCR 0x000040
+#define MCF_SDRAMC_DACR0 0x000048
+#define MCF_SDRAMC_DMR0 0x00004C
+
+#define MCF_SDRAMC_DCR_RC(x) (((x)&0x01FF)<<0)
+#define MCF_SDRAMC_DCR_RTIM(x) (((x)&0x0003)<<9)
+#define MCF_SDRAMC_DCR_IS 0x0800
+#define MCF_SDRAMC_DCR_COC 0x1000
+#define MCF_SDRAMC_DCR_NAM 0x2000
+
+#define MCF_SDRAMC_DACRn_IP 0x00000008
+#define MCF_SDRAMC_DACRn_PS(x) (((x)&0x00000003)<<4)
+#define MCF_SDRAMC_DACRn_MRS 0x00000040
+#define MCF_SDRAMC_DACRn_CBM(x) (((x)&0x00000007)<<8)
+#define MCF_SDRAMC_DACRn_CASL(x) (((x)&0x00000003)<<12)
+#define MCF_SDRAMC_DACRn_RE 0x00008000
+#define MCF_SDRAMC_DACRn_BA(x) (((x)&0x00003FFF)<<18)
+
+#define MCF_SDRAMC_DMRn_BAM_8M 0x007C0000
+#define MCF_SDRAMC_DMRn_BAM_16M 0x00FC0000
+#define MCF_SDRAMC_DMRn_V 0x00000001
+
+#define MCFSIM_ICR1 0x000C41
+
+#endif /* _MCF5271_H_ */
diff --git a/include/asm-m68k/mcftimer.h b/include/asm-m68k/mcftimer.h
index 047950b..a73b80e 100644
--- a/include/asm-m68k/mcftimer.h
+++ b/include/asm-m68k/mcftimer.h
@@ -45,7 +45,7 @@
#elif defined(CONFIG_M5249) || defined(CONFIG_M5307) || defined(CONFIG_M5407)
#define MCFTIMER_BASE1 0x140 /* Base address of TIMER1 */
#define MCFTIMER_BASE2 0x180 /* Base address of TIMER2 */
-#elif defined(CONFIG_M5282)
+#elif defined(CONFIG_M5282) | defined(CONFIG_M5271)
#define MCFTIMER_BASE1 0x150000 /* Base address of TIMER1 */
#define MCFTIMER_BASE2 0x160000 /* Base address of TIMER2 */
#define MCFTIMER_BASE3 0x170000 /* Base address of TIMER4 */
diff --git a/include/asm-m68k/mcfuart.h b/include/asm-m68k/mcfuart.h
index e5082a9..7c0999d 100644
--- a/include/asm-m68k/mcfuart.h
+++ b/include/asm-m68k/mcfuart.h
@@ -46,7 +46,7 @@
#define MCFUART_BASE1 0x140 /* Base address of UART1 */
#define MCFUART_BASE2 0x180 /* Base address of UART2 */
#endif
-#elif defined(CONFIG_M5282)
+#elif defined(CONFIG_M5282) || defined(CONFIG_M5271)
#define MCFUART_BASE1 0x200 /* Base address of UART1 */
#define MCFUART_BASE2 0x240 /* Base address of UART2 */
#define MCFUART_BASE3 0x280 /* Base address of UART3 */
diff --git a/include/asm-m68k/ptrace.h b/include/asm-m68k/ptrace.h
index a6d3d74..75b2418 100644
--- a/include/asm-m68k/ptrace.h
+++ b/include/asm-m68k/ptrace.h
@@ -43,7 +43,7 @@
ulong a4;
ulong a5;
ulong a6;
-#if defined(CONFIG_M5272) || defined(CONFIG_M5282) || defined(CONFIG_M5249)
+#if defined(CONFIG_M5272) || defined(CONFIG_M5282) || defined(CONFIG_M5249) || defined(CONFIG_M5271)
unsigned format : 4; /* frame format specifier */
unsigned vector : 12; /* vector offset */
unsigned short sr;
diff --git a/include/asm-ppc/i2c.h b/include/asm-ppc/i2c.h
index fa9d164..1680d3a 100644
--- a/include/asm-ppc/i2c.h
+++ b/include/asm-ppc/i2c.h
@@ -87,7 +87,7 @@
#error CFG_I2C_OFFSET is not defined in /include/configs/${BOARD}.h
#endif
-#if defined(CONFIG_MPC8349ADS) || defined(CONFIG_TQM834X)
+#if defined(CONFIG_MPC8349EMDS) || defined(CONFIG_TQM834X)
/*
* MPC8349 have two i2c bus
*/
diff --git a/include/configs/BC3450.h b/include/configs/BC3450.h
index a79de40..5b54f30 100644
--- a/include/configs/BC3450.h
+++ b/include/configs/BC3450.h
@@ -42,21 +42,21 @@
#define CONFIG_MPC5200 1 /* (more precisely a MPC5200 CPU) */
#define CONFIG_TQM5200 1 /* ... on a TQM5200 module */
-#define CONFIG_BC3450 1 /* ... on a BC3450 mainboard */
-#define CONFIG_BC3450_PS2 1 /* + a PS/2 converter onboard */
-#define CONFIG_BC3450_IDE 1 /* + IDE drives (Compact Flash) */
+#define CONFIG_BC3450 1 /* ... on a BC3450 mainboard */
+#define CONFIG_BC3450_PS2 1 /* + a PS/2 converter onboard */
+#define CONFIG_BC3450_IDE 1 /* + IDE drives (Compact Flash) */
#define CONFIG_BC3450_USB 1 /* + USB support */
# define CONFIG_FAT 1 /* + FAT support */
# define CONFIG_EXT2 1 /* + EXT2 support */
#undef CONFIG_BC3450_BUZZER /* + Buzzer onboard */
#undef CONFIG_BC3450_CAN /* + CAN transceiver */
#undef CONFIG_BC3450_DS1340 /* + a RTC DS1340 onboard */
-#undef CONFIG_BC3450_DS3231 /* + a RTC DS3231 onboard tbd */
-#undef CONFIG_BC3450_AC97 /* + AC97 on PSC2, tbd */
+#undef CONFIG_BC3450_DS3231 /* + a RTC DS3231 onboard tbd */
+#undef CONFIG_BC3450_AC97 /* + AC97 on PSC2, tbd */
#define CONFIG_BC3450_FP 1 /* + enable FP O/P */
#undef CONFIG_BC3450_CRT /* + enable CRT O/P (Debug only!) */
-#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
+#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
@@ -91,7 +91,7 @@
*/
# define CONFIG_PCI 1
# define CONFIG_PCI_PNP 1
-/* #define CONFIG_PCI_SCAN_SHOW 1 */
+/* #define CONFIG_PCI_SCAN_SHOW 1 */
#define CONFIG_PCI_MEM_BUS 0x40000000
#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
@@ -103,7 +103,7 @@
#define CONFIG_NET_MULTI 1
/*#define CONFIG_EEPRO100 XXX - FIXME: conflicts when CONFIG_MII is enabled */
-#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
+#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define CONFIG_NS8382X 1
#ifdef CONFIG_PCI
@@ -132,15 +132,15 @@
# define ADD_BMP_CMD 0
#endif
-/*
- * Partitions
+/*
+ * Partitions
*/
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
#define CONFIG_ISO_PARTITION
-/*
- * USB
+/*
+ * USB
*/
#ifdef CONFIG_BC3450_USB
# define CONFIG_USB_OHCI
@@ -150,8 +150,8 @@
# define ADD_USB_CMD 0
#endif /* CONFIG_BC3450_USB */
-/*
- * POST support
+/*
+ * POST support
*/
#define CONFIG_POST (CFG_POST_MEMORY | \
CFG_POST_CPU | \
@@ -165,8 +165,8 @@
# define CFG_CMD_POST_DIAG 0
#endif /* CONFIG_POST */
-/*
- * IDE
+/*
+ * IDE
*/
#ifdef CONFIG_BC3450_IDE
# define ADD_IDE_CMD CFG_CMD_IDE
@@ -219,7 +219,7 @@
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
-#define CONFIG_TIMESTAMP /* display image timestamps */
+#define CONFIG_TIMESTAMP /* display image timestamps */
#if (TEXT_BASE == 0xFC000000) /* Boot low */
# define CFG_LOWBOOT 1
@@ -242,14 +242,14 @@
"ipaddr=192.168.1.10\0" \
"serverip=192.168.1.3\0" \
"netmask=255.255.255.0\0" \
- "hostname=bc3450\0" \
+ "hostname=bc3450\0" \
"rootpath=/opt/eldk/ppc_6xx\0" \
- "kernel_addr=fc0a0000\0" \
- "ramdisk_addr=fc1c0000\0" \
+ "kernel_addr=fc0a0000\0" \
+ "ramdisk_addr=fc1c0000\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=$(serverip):$(rootpath)\0" \
- "ideargs=setenv bootargs root=/dev/hda2 ro\0" \
+ "ideargs=setenv bootargs root=/dev/hda2 ro\0" \
"addip=setenv bootargs $(bootargs) " \
"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
":$(hostname):$(netdev):off panic=1\0" \
@@ -260,10 +260,10 @@
"flash_nfs=run nfsargs addip addcons; bootm $(kernel_addr)\0" \
"net_nfs=tftp 200000 $(bootfile); " \
"run nfsargs addip addcons; bootm\0" \
- "ide_nfs=run nfsargs addip addcons; " \
- "disk 200000 0:1; bootm\0" \
- "ide_ide=run ideargs addip addcons; " \
- "disk 200000 0:1; bootm\0" \
+ "ide_nfs=run nfsargs addip addcons; " \
+ "disk 200000 0:1; bootm\0" \
+ "ide_ide=run ideargs addip addcons; " \
+ "disk 200000 0:1; bootm\0" \
"usb_self=run usbload; run ramargs addip addcons; " \
"bootm 200000 400000\0" \
"usbload=usb reset; usb scan; usbboot 200000 0:1; " \
@@ -288,7 +288,7 @@
* PCI Bus clocking configuration
*
* Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
- * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet
+ * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet
* hasn't been tested with a IPB Bus Clock of 66 MHz.
*/
#if defined(CFG_IPBSPEED_133)
@@ -314,9 +314,9 @@
#define CFG_I2C_SLAVE 0x7F
/*
- * EEPROM configuration for I²C EEPROM M24C32
+ * EEPROM configuration for I²C EEPROM M24C32
* M24C64 should work also. For other EEPROMs config should be verified.
- *
+ *
* The TQM5200 module may hold an EEPROM at address 0x50.
*/
#define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x (TQM) */
@@ -376,7 +376,7 @@
#define CFG_ENV_SIZE 0x10000
#define CFG_ENV_SECT_SIZE 0x20000
#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
/*
* Memory map
@@ -419,25 +419,25 @@
/*
* GPIO configuration on BC3450
*
- * PSC1: UART1 (Service-UART) [0x xxxxxxx4]
- * PSC2: UART2 [0x xxxxxx4x]
- * or: AC/97 if CONFIG_BC3450_AC97 [0x xxxxxx2x]
- * PSC3: USB2 [0x xxxxx1xx]
- * USB: UART4(ext.)/UART5(int.) [0x xxxx2xxx]
- * (this has to match
- * CONFIG_USB_CONFIG which is
- * used by usb_ohci.c to set
- * the USB ports)
- * Eth: 10/100Mbit Ethernet [0x xxx0xxxx]
- * (this is reset to '5'
- * in FEC driver: fec.c)
- * PSC6: UART6 (int. to PS/2 contr.) [0x xx5xxxxx]
- * ATA/CS: ??? [0x x1xxxxxx]
- * FIXME! UM Fig 2-10 suggests [0x x0xxxxxx]
+ * PSC1: UART1 (Service-UART) [0x xxxxxxx4]
+ * PSC2: UART2 [0x xxxxxx4x]
+ * or: AC/97 if CONFIG_BC3450_AC97 [0x xxxxxx2x]
+ * PSC3: USB2 [0x xxxxx1xx]
+ * USB: UART4(ext.)/UART5(int.) [0x xxxx2xxx]
+ * (this has to match
+ * CONFIG_USB_CONFIG which is
+ * used by usb_ohci.c to set
+ * the USB ports)
+ * Eth: 10/100Mbit Ethernet [0x xxx0xxxx]
+ * (this is reset to '5'
+ * in FEC driver: fec.c)
+ * PSC6: UART6 (int. to PS/2 contr.) [0x xx5xxxxx]
+ * ATA/CS: ??? [0x x1xxxxxx]
+ * FIXME! UM Fig 2-10 suggests [0x x0xxxxxx]
* CS1: Use Pin gpio_wkup_6 as second
- * SDRAM chip select (mem_cs1)
+ * SDRAM chip select (mem_cs1)
* Timer: CAN2 / SPI
- * I2C: CAN1 / I²C2 [0x bxxxxxxx]
+ * I2C: CAN1 / I²C2 [0x bxxxxxxx]
*/
#ifdef CONFIG_BC3450_AC97
# define CFG_GPS_PORT_CONFIG 0xb1502124
@@ -465,7 +465,7 @@
#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_HZ 1000 /* dec freq: 1ms ticks */
@@ -489,7 +489,7 @@
#define CFG_BOOTCS_START CFG_FLASH_BASE
#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
#ifdef CFG_PCISPEED_66
-# define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
+# define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
#else
# define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */
#endif
@@ -533,17 +533,17 @@
* USB stuff
*/
#define CONFIG_USB_CLOCK 0x0001BBBB
-#define CONFIG_USB_CONFIG 0x00002000 /* we're using Port 2 */
+#define CONFIG_USB_CONFIG 0x00002000 /* we're using Port 2 */
/*
* IDE/ATA stuff Supports IDE harddisk
*/
#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
+#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
+#undef CONFIG_IDE_LED /* LED for ide not supported */
-#define CONFIG_IDE_RESET /* reset for ide supported */
+#define CONFIG_IDE_RESET /* reset for ide supported */
#define CONFIG_IDE_PREINIT
#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
diff --git a/include/configs/M5271EVB.h b/include/configs/M5271EVB.h
new file mode 100644
index 0000000..3935f56
--- /dev/null
+++ b/include/configs/M5271EVB.h
@@ -0,0 +1,154 @@
+/*
+ * Configuation settings for the Freescale M5271EVB
+ *
+ * Based on MC5272C3 and r5200 board configs
+ * (C) Copyright 2006 Lab X Technologies <zachary.landau@labxtechnologies.com>
+ * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef _M5271EVB_H
+#define _M5271EVB_H
+
+#define DEBUG
+#undef DEBUG
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_MCF52x2 /* define processor family */
+#define CONFIG_M5271 /* define processor type */
+#define CONFIG_M5271EVB /* define board type */
+
+#define CONFIG_IPADDR 192.168.30.1
+#define CONFIG_SERVERIP 192.168.1.1
+#define CONFIG_ETHADDR 00:06:3b:01:41:55
+
+#define CONFIG_BAUDRATE 19200
+#define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
+
+#undef CONFIG_WATCHDOG /* disable watchdog */
+
+/* Configuration for environment
+ * Environment is embedded in u-boot in the second sector of the flash
+ */
+#ifndef CONFIG_MONITOR_IS_IN_RAM
+#define CFG_ENV_OFFSET 0x4000
+#define CFG_ENV_SECT_SIZE 0x2000
+#define CFG_ENV_IS_IN_FLASH 1
+#else
+#define CFG_ENV_ADDR 0xffe04000
+#define CFG_ENV_SECT_SIZE 0x2000
+#define CFG_ENV_IS_IN_FLASH 1
+#endif
+
+#define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PING | CFG_CMD_NET ) & ~(CFG_CMD_LOADS | CFG_CMD_LOADB))
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#define CFG_PROMPT "=> "
+#define CFG_LONGHELP /* undef to save memory */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_LOAD_ADDR 0x00100000
+
+#define CFG_MEMTEST_START 0x400
+#define CFG_MEMTEST_END 0x380000
+
+#define CFG_HZ 1000000
+#define CFG_CLK 100000000
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+
+#define CFG_MBAR 0x40000000 /* Register Base Addrs */
+
+/* Enable FEC ethernet */
+#define FEC_ENET
+#define CONFIG_NET_RETRY_COUNT 5
+#define CFG_ENET_BD_BASE 0x480000
+
+/*
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR 0x20000000
+#define CFG_INIT_RAM_END 0x1000 /* End of used area in internal SRAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_SDRAM_SIZE 16 /* SDRAM size in MB */
+#define CFG_FLASH_BASE 0xffe00000
+
+#ifdef CONFIG_MONITOR_IS_IN_RAM
+#define CFG_MONITOR_BASE 0x20000
+#else
+#define CFG_MONITOR_BASE (CFG_FLASH_BASE + 0x400)
+#endif
+
+#define CFG_MONITOR_LEN 0x40000
+#define CFG_MALLOC_LEN (256 << 10)
+#define CFG_BOOTPARAMS_LEN (64*1024)
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization ??
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/* FLASH organization */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 11 /* max number of sectors on one chip */
+#define CFG_FLASH_ERASE_TOUT 1000
+
+#define CFG_FLASH_CFI 1
+#define CFG_FLASH_CFI_DRIVER 1
+#define CFG_FLASH_SIZE 0x200000
+
+/* Cache Configuration */
+#define CFG_CACHELINE_SIZE 16
+
+/* Port configuration */
+#define CFG_FECI2C 0xF0
+
+#endif /* _M5271EVB_H */
diff --git a/include/configs/MPC8349ADS.h b/include/configs/MPC8349ADS.h
deleted file mode 100644
index 1e9a1f7..0000000
--- a/include/configs/MPC8349ADS.h
+++ /dev/null
@@ -1,653 +0,0 @@
-/*
- * Copyright 2004 Freescale Semiconductor.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
- * mpc8349ads board configuration file
- *
- * Please refer to doc/README.mpc83xxads for more info.
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#undef DEBUG
-
-#define CONFIG_MII
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_E300 1 /* E300 Family */
-#define CONFIG_MPC83XX 1 /* MPC83XX family */
-#define CONFIG_MPC8349 1 /* MPC8349 specific */
-#define CONFIG_MPC8349ADS 1 /* MPC8349ADS board specific */
-
-#define CONFIG_PCI
-#undef CONFIG_MPC83XX_PCI2 /* support for 2nd PCI controller */
-#define CONFIG_TSEC_ENET /* tsec ethernet support */
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
-
-#undef CONFIG_DDR_ECC /* only for ECC DDR module */
-
-#define PCI_66M
-#ifdef PCI_66M
-#define CONFIG_83XX_CLKIN 66000000 /* in Hz */
-#else
-#define CONFIG_83XX_CLKIN 33000000 /* in Hz */
-#endif
-
-#ifndef CONFIG_SYS_CLK_FREQ
-#ifdef PCI_66M
-#define CONFIG_SYS_CLK_FREQ 66000000
-#else
-#define CONFIG_SYS_CLK_FREQ 33000000
-#endif
-#endif
-
-#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
-
-#define CFG_IMMRBAR 0xE0000000
-
-#undef CFG_DRAM_TEST /* memory test, takes time */
-#define CFG_MEMTEST_START 0x00000000 /* memtest region */
-#define CFG_MEMTEST_END 0x00100000
-
-/*
- * DDR Setup
- */
-
-#define CFG_DDR_BASE 0x00000000 /* DDR is system memory*/
-#define CFG_SDRAM_BASE CFG_DDR_BASE
-#undef CONFIG_DDR_2T_TIMING
-#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE
-
-#if defined(CONFIG_SPD_EEPROM)
- /*
- * Determine DDR configuration from I2C interface.
- */
- #define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
-#else
- /*
- * Manually set up DDR parameters
- */
- #define CFG_DDR_SIZE 256 /* Mb */
- #define CFG_DDR_CONFIG (CSCONFIG_EN | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_9)
- #define CFG_DDR_TIMING_1 0x37344321
- #define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */
- #define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */
- #define CFG_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */
- #define CFG_DDR_INTERVAL 0x05200100 /* autocharge,no open page */
-#endif
-
-/*
- * SDRAM on the Local Bus
- */
-#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
-#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
-
-/*
- * FLASH on the Local Bus
- */
-#define CFG_FLASH_CFI /* use the Common Flash Interface */
-#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */
-#define CFG_FLASH_BASE 0xFE000000 /* start of FLASH */
-#define CFG_FLASH_SIZE 8 /* FLASH size in MB */
-/* #define CFG_FLASH_USE_BUFFER_WRITE */
-
-#define CFG_BR0_PRELIM (CFG_FLASH_BASE | /* Flash Base address */ \
- (2 << BR_PS_SHIFT) | /* 32 bit port size */ \
- BR_V) /* valid */
-#define CFG_OR0_PRELIM 0xff806ff7 /* 16Mb Flash size*/
-#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */
-#define CFG_LBLAWAR0_PRELIM 0x80000016 /* 16Mb window size */
-
-#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
-#define CFG_MAX_FLASH_SECT 64 /* sectors per device */
-
-#undef CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
-#define CFG_MID_FLASH_JUMP 0x7F000000
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
-
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
-#define CFG_RAMBOOT
-#else
-#undef CFG_RAMBOOT
-#endif
-
-/*
- * BCSR register on local bus 32KB, 8-bit wide for ADS config reg
- */
-#define CFG_BCSR 0xF8000000
-#define CFG_LBLAWBAR1_PRELIM CFG_BCSR /* Access window base at BCSR base */
-#define CFG_LBLAWAR1_PRELIM 0x8000000E /* Access window size 32K */
-#define CFG_BR1_PRELIM (CFG_BCSR|0x00000801) /* Port-size=8bit, MSEL=GPCM */
-#define CFG_OR1_PRELIM 0xFFFFE8f0 /* length 32K */
-
-#define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0x40000000 /* Initial RAM address */
-#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM*/
-
-#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
-
-/*
- * Local Bus LCRR and LBCR regs
- * LCRR: DLL bypass, Clock divider is 4
- * External Local Bus rate is
- * CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
- */
-#define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_4)
-#define CFG_LBC_LBCR 0x00000000
-
-#define CFG_LB_SDRAM /* if board has SRDAM on local bus */
-
-#ifdef CFG_LB_SDRAM
-/*local bus BR2, OR2 definition for SDRAM if soldered on the ADS board*/
-/*
- * Base Register 2 and Option Register 2 configure SDRAM.
- * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000.
- *
- * For BR2, need:
- * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
- * port-size = 32-bits = BR2[19:20] = 11
- * no parity checking = BR2[21:22] = 00
- * SDRAM for MSEL = BR2[24:26] = 011
- * Valid = BR[31] = 1
- *
- * 0 4 8 12 16 20 24 28
- * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
- *
- * FIXME: CFG_LBC_SDRAM_BASE should be masked and OR'ed into
- * FIXME: the top 17 bits of BR2.
- */
-
-#define CFG_BR2_PRELIM 0xf0001861 /*Port-size=32bit, MSEL=SDRAM*/
-#define CFG_LBLAWBAR2_PRELIM 0xF0000000
-#define CFG_LBLAWAR2_PRELIM 0x80000019 /*64M*/
-
-/*
- * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64.
- *
- * For OR2, need:
- * 64MB mask for AM, OR2[0:7] = 1111 1100
- * XAM, OR2[17:18] = 11
- * 9 columns OR2[19-21] = 010
- * 13 rows OR2[23-25] = 100
- * EAD set for extra time OR[31] = 1
- *
- * 0 4 8 12 16 20 24 28
- * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
- */
-
-#define CFG_OR2_PRELIM 0xfc006901
-
-#define CFG_LBC_LSRT 0x32000000 /* LB sdram refresh timer, about 6us */
-#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer prescal, 266MHz/32*/
-
-/*
- * LSDMR masks
- */
-#define CFG_LBC_LSDMR_RFEN (1 << (31 - 1))
-#define CFG_LBC_LSDMR_BSMA1516 (3 << (31 - 10))
-#define CFG_LBC_LSDMR_BSMA1617 (4 << (31 - 10))
-#define CFG_LBC_LSDMR_RFCR5 (3 << (31 - 16))
-#define CFG_LBC_LSDMR_RFCR8 (5 << (31 - 16))
-#define CFG_LBC_LSDMR_RFCR16 (7 << (31 - 16))
-#define CFG_LBC_LSDMR_PRETOACT3 (3 << (31 - 19))
-#define CFG_LBC_LSDMR_PRETOACT6 (5 << (31 - 19))
-#define CFG_LBC_LSDMR_PRETOACT7 (7 << (31 - 19))
-#define CFG_LBC_LSDMR_ACTTORW3 (3 << (31 - 22))
-#define CFG_LBC_LSDMR_ACTTORW7 (7 << (31 - 22))
-#define CFG_LBC_LSDMR_ACTTORW6 (6 << (31 - 22))
-#define CFG_LBC_LSDMR_BL8 (1 << (31 - 23))
-#define CFG_LBC_LSDMR_WRC2 (2 << (31 - 27))
-#define CFG_LBC_LSDMR_WRC3 (3 << (31 - 27))
-#define CFG_LBC_LSDMR_WRC4 (0 << (31 - 27))
-#define CFG_LBC_LSDMR_BUFCMD (1 << (31 - 29))
-#define CFG_LBC_LSDMR_CL3 (3 << (31 - 31))
-
-#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4))
-
-#define CFG_LBC_LSDMR_COMMON ( CFG_LBC_LSDMR_RFEN \
- | CFG_LBC_LSDMR_BSMA1516 \
- | CFG_LBC_LSDMR_RFCR8 \
- | CFG_LBC_LSDMR_PRETOACT6 \
- | CFG_LBC_LSDMR_ACTTORW3 \
- | CFG_LBC_LSDMR_BL8 \
- | CFG_LBC_LSDMR_WRC3 \
- | CFG_LBC_LSDMR_CL3 \
- )
-
-/*
- * SDRAM Controller configuration sequence.
- */
-#define CFG_LBC_LSDMR_1 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_PCHALL)
-#define CFG_LBC_LSDMR_2 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_ARFRSH)
-#define CFG_LBC_LSDMR_3 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_ARFRSH)
-#define CFG_LBC_LSDMR_4 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_MRW)
-#define CFG_LBC_LSDMR_5 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_NORMAL)
-#endif
-
-/*
- * Serial Port
- */
-#define CONFIG_CONS_INDEX 1
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE 1
-#define CFG_NS16550_CLK get_bus_freq(0)
-
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-
-#define CFG_NS16550_COM1 (CFG_IMMRBAR+0x4500)
-#define CFG_NS16550_COM2 (CFG_IMMRBAR+0x4600)
-
-/* Use the HUSH parser */
-#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
-#endif
-
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
-#define CFG_I2C_OFFSET 0x3000
-#define CFG_I2C2_OFFSET 0x3100
-
-/* TSEC */
-#define CFG_TSEC1_OFFSET 0x24000
-#define CFG_TSEC1 (CFG_IMMRBAR+CFG_TSEC1_OFFSET)
-#define CFG_TSEC2_OFFSET 0x25000
-#define CFG_TSEC2 (CFG_IMMRBAR+CFG_TSEC2_OFFSET)
-
-/* IO Configuration */
-#define CFG_IO_CONF (\
- IO_CONF_UART |\
- IO_CONF_TSEC1 |\
- IO_CONF_IRQ0 |\
- IO_CONF_IRQ1 |\
- IO_CONF_IRQ2 |\
- IO_CONF_IRQ3 |\
- IO_CONF_IRQ4 |\
- IO_CONF_IRQ5 |\
- IO_CONF_IRQ6 |\
- IO_CONF_IRQ7 )
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-
-#define CFG_PCI1_MEM_BASE 0x80000000
-#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
-#define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */
-#define CFG_PCI1_MMIO_BASE 0x90000000
-#define CFG_PCI1_MMIO_PHYS CFG_PCI1_MMIO_BASE
-#define CFG_PCI1_MMIO_SIZE 0x10000000 /* 256M */
-#define CFG_PCI1_IO_BASE 0x00000000
-#define CFG_PCI1_IO_PHYS 0xe2000000
-#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */
-
-#define CFG_PCI2_MEM_BASE 0xa0000000
-#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
-#define CFG_PCI2_MEM_SIZE 0x10000000 /* 256M */
-#define CFG_PCI2_MMIO_BASE 0xb0000000
-#define CFG_PCI2_MMIO_PHYS CFG_PCI2_MMIO_BASE
-#define CFG_PCI2_MMIO_SIZE 0x10000000 /* 256M */
-#define CFG_PCI2_IO_BASE 0x00000000
-#define CFG_PCI2_IO_PHYS 0xe2100000
-#define CFG_PCI2_IO_SIZE 0x00100000 /* 1M */
-#if defined(CONFIG_PCI)
-
-#define PCI_ALL_PCI1
-#if defined(PCI_64BIT)
-#undef PCI_ALL_PCI1
-#undef PCI_TWO_PCI1
-#undef PCI_ONE_PCI1
-#endif
-
-#define CONFIG_NET_MULTI
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
-
-#undef CONFIG_EEPRO100
-#undef CONFIG_TULIP
-
-#if !defined(CONFIG_PCI_PNP)
- #define PCI_ENET0_IOADDR 0xFIXME
- #define PCI_ENET0_MEMADDR 0xFIXME
- #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
-#endif
-
-#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
-
-#endif /* CONFIG_PCI */
-
-#if defined(CONFIG_TSEC_ENET)
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI 1
-#endif
-
-#define CONFIG_GMII 1 /* MII PHY management */
-#define CONFIG_MPC83XX_TSEC1 1
-#define CONFIG_MPC83XX_TSEC1_NAME "TSEC0"
-#define CONFIG_MPC83XX_TSEC2 1
-#define CONFIG_MPC83XX_TSEC2_NAME "TSEC1"
-#define TSEC1_PHY_ADDR 0
-#define TSEC2_PHY_ADDR 1
-#define TSEC1_PHYIDX 0
-#define TSEC2_PHYIDX 0
-
-/* Options are: TSEC[0-1] */
-#define CONFIG_ETHPRIME "TSEC0"
-
-#endif /* CONFIG_TSEC_ENET */
-
-/*
- * Environment
- */
-#ifndef CFG_RAMBOOT
- #define CFG_ENV_IS_IN_FLASH 1
- #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
- #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
- #define CFG_ENV_SIZE 0x2000
-#else
- #define CFG_NO_FLASH 1 /* Flash is not usable now */
- #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
- #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
- #define CFG_ENV_SIZE 0x2000
-#endif
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#if defined(CFG_RAMBOOT)
-#if defined(CONFIG_PCI)
-#define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
- | CFG_CMD_PING \
- | CFG_CMD_PCI \
- | CFG_CMD_I2C) \
- & \
- ~(CFG_CMD_ENV \
- | CFG_CMD_LOADS))
-#else
-#define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
- | CFG_CMD_PING \
- | CFG_CMD_I2C) \
- & \
- ~(CFG_CMD_ENV \
- | CFG_CMD_LOADS))
-#endif
-#else
-#if defined(CONFIG_PCI)
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
- | CFG_CMD_PCI \
- | CFG_CMD_PING \
- | CFG_CMD_I2C)
-#else
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
- | CFG_CMD_PING \
- | CFG_CMD_I2C \
- | CFG_CMD_MII \
- )
-#endif
-#endif
-
-#include <cmd_confdefs.h>
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_LOAD_ADDR 0x2000000 /* default load address */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
- #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
- #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
-
-/* Cache Configuration */
-#define CFG_DCACHE_SIZE 32768
-#define CFG_CACHELINE_SIZE 32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
-#endif
-
-#define CFG_RCWH_PCIHOST 0x80000000 /* PCIHOST */
-
-#define CFG_HRCW_LOW (\
- HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
- HRCWL_DDR_TO_SCB_CLK_1X1 |\
- HRCWL_CSB_TO_CLKIN_4X1 |\
- HRCWL_VCO_1X2 |\
- HRCWL_CORE_TO_CSB_2X1)
-
-#if defined(PCI_64BIT)
-#define CFG_HRCW_HIGH (\
- HRCWH_PCI_HOST |\
- HRCWH_64_BIT_PCI |\
- HRCWH_PCI1_ARBITER_ENABLE |\
- HRCWH_PCI2_ARBITER_DISABLE |\
- HRCWH_CORE_ENABLE |\
- HRCWH_FROM_0X00000100 |\
- HRCWH_BOOTSEQ_DISABLE |\
- HRCWH_SW_WATCHDOG_DISABLE |\
- HRCWH_ROM_LOC_LOCAL_16BIT |\
- HRCWH_TSEC1M_IN_GMII |\
- HRCWH_TSEC2M_IN_GMII )
-#else
-#define CFG_HRCW_HIGH (\
- HRCWH_PCI_HOST |\
- HRCWH_32_BIT_PCI |\
- HRCWH_PCI1_ARBITER_ENABLE |\
- HRCWH_PCI2_ARBITER_ENABLE |\
- HRCWH_CORE_ENABLE |\
- HRCWH_FROM_0X00000100 |\
- HRCWH_BOOTSEQ_DISABLE |\
- HRCWH_SW_WATCHDOG_DISABLE |\
- HRCWH_ROM_LOC_LOCAL_16BIT |\
- HRCWH_TSEC1M_IN_GMII |\
- HRCWH_TSEC2M_IN_GMII )
-#endif
-
-/* System IO Config */
-#define CFG_SICRH SICRH_TSOBI1
-#define CFG_SICRL SICRL_LDP_A
-
-#define CFG_HID0_INIT 0x000000000
-
-#define CFG_HID0_FINAL CFG_HID0_INIT
-
-/* #define CFG_HID0_FINAL (\
- HID0_ENABLE_INSTRUCTION_CACHE |\
- HID0_ENABLE_M_BIT |\
- HID0_ENABLE_ADDRESS_BROADCAST ) */
-
-#define CFG_HID2 HID2_HBE
-
-/* DDR 0 - 256MB */
-#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-
-/* stack in DCACHE @ 1GB (no backing mem) */
-#define CFG_IBAT1L (CFG_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT1U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-
-/* 2G - 3G PCI */
-#ifdef CONFIG_PCI
-#define CFG_IBAT2L (CFG_PCI1_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT2U (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_IBAT3L (CFG_PCI1_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT3U (CFG_PCI1_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-#else
-#define CFG_IBAT2L (0)
-#define CFG_IBAT2U (0)
-#define CFG_IBAT3L (0)
-#define CFG_IBAT3U (0)
-#endif
-
-#ifdef CONFIG_MPC83XX_PCI2
-#define CFG_IBAT4L (CFG_PCI2_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT4U (CFG_PCI2_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_IBAT5L (CFG_PCI2_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT5U (CFG_PCI2_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-#else
-#define CFG_IBAT4L (0)
-#define CFG_IBAT4U (0)
-#define CFG_IBAT5L (0)
-#define CFG_IBAT5U (0)
-#endif
-
-/* IMMRBAR */
-#define CFG_IBAT6L (CFG_IMMRBAR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT6U (CFG_IMMRBAR | BATU_BL_256M | BATU_VS | BATU_VP)
-
-/* SDRAM, BCSR & FLASH */
-#define CFG_IBAT7L (0xf0000000 | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT7U (0xf0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CFG_DBAT0L CFG_IBAT0L
-#define CFG_DBAT0U CFG_IBAT0U
-#define CFG_DBAT1L CFG_IBAT1L
-#define CFG_DBAT1U CFG_IBAT1U
-#define CFG_DBAT2L CFG_IBAT2L
-#define CFG_DBAT2U CFG_IBAT2U
-#define CFG_DBAT3L CFG_IBAT3L
-#define CFG_DBAT3U CFG_IBAT3U
-#define CFG_DBAT4L CFG_IBAT4L
-#define CFG_DBAT4U CFG_IBAT4U
-#define CFG_DBAT5L CFG_IBAT5L
-#define CFG_DBAT5U CFG_IBAT5U
-#define CFG_DBAT6L CFG_IBAT6L
-#define CFG_DBAT6U CFG_IBAT6U
-#define CFG_DBAT7L CFG_IBAT7L
-#define CFG_DBAT7U CFG_IBAT7U
-
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/*
- * Environment Configuration
- */
-
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_ETHADDR 00:04:9f:11:22:33
-#define CONFIG_HAS_ETH1
-#define CONFIG_ETH1ADDR 00:E0:0C:00:7D:01
-#endif
-
-#define CONFIG_IPADDR 192.168.1.253
-
-#define CONFIG_HOSTNAME unknown
-#define CONFIG_ROOTPATH /nfsroot
-#define CONFIG_BOOTFILE your.uImage
-
-#define CONFIG_SERVERIP 192.168.1.1
-#define CONFIG_GATEWAYIP 192.168.1.1
-#define CONFIG_NETMASK 255.255.255.0
-
-#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
-
-#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
-#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
-
-#define CONFIG_BAUDRATE 115200
-
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "consoledev=ttyS0\0" \
- "ramdiskaddr=400000\0" \
- "ramdiskfile=ramfs.83xx\0"
-
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "bootm $loadaddr"
-
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "bootm $loadaddr $ramdiskaddr"
-
-#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/MPC8349EMDS.h b/include/configs/MPC8349EMDS.h
index 1a47980..0300b0d 100644
--- a/include/configs/MPC8349EMDS.h
+++ b/include/configs/MPC8349EMDS.h
@@ -29,7 +29,6 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-#define DEBUG
#undef DEBUG
/*
@@ -40,8 +39,8 @@
#define CONFIG_MPC8349 1 /* MPC8349 specific */
#define CONFIG_MPC8349EMDS 1 /* MPC8349EMDS board specific */
-/* FIXME: Real PCI support will come in a follow-up update. */
-#undef CONFIG_PCI
+#undef CONFIG_PCI
+#undef CONFIG_MPC83XX_PCI2 /* support for 2nd PCI controller */
#define PCI_66M
#ifdef PCI_66M
@@ -53,8 +52,10 @@
#ifndef CONFIG_SYS_CLK_FREQ
#ifdef PCI_66M
#define CONFIG_SYS_CLK_FREQ 66000000
+#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_4X1
#else
#define CONFIG_SYS_CLK_FREQ 33000000
+#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_8X1
#endif
#endif
@@ -69,7 +70,7 @@
/*
* DDR Setup
*/
-#define CONFIG_DDR_ECC /* only for ECC DDR module */
+#undef CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */
#define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/
@@ -157,7 +158,7 @@
/*
* BCSR register on local bus 32KB, 8-bit wide for MDS config reg
*/
-#define CFG_BCSR 0xF8000000
+#define CFG_BCSR 0xE2400000
#define CFG_LBLAWBAR1_PRELIM CFG_BCSR /* Access window base at BCSR base */
#define CFG_LBLAWAR1_PRELIM 0x8000000E /* Access window size 32K */
#define CFG_BR1_PRELIM (CFG_BCSR|0x00000801) /* Port-size=8bit, MSEL=GPCM */
@@ -165,7 +166,7 @@
#define CONFIG_L1_INIT_RAM
#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0xE8000000 /* Initial RAM address */
+#define CFG_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */
#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM*/
#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */
@@ -322,18 +323,8 @@
#define CFG_TSEC2_OFFSET 0x25000
#define CFG_TSEC2 (CFG_IMMRBAR+CFG_TSEC2_OFFSET)
-/* IO Configuration */
-#define CFG_IO_CONF (\
- IO_CONF_UART |\
- IO_CONF_TSEC1 |\
- IO_CONF_IRQ0 |\
- IO_CONF_IRQ1 |\
- IO_CONF_IRQ2 |\
- IO_CONF_IRQ3 |\
- IO_CONF_IRQ4 |\
- IO_CONF_IRQ5 |\
- IO_CONF_IRQ6 |\
- IO_CONF_IRQ7 )
+/* USB */
+#define CFG_USE_MPC834XSYS_USB_PHY 1 /* Use SYS board PHY */
/*
* General PCI
@@ -341,21 +332,27 @@
*/
#define CFG_PCI1_MEM_BASE 0x80000000
#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
-#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */
+#define CFG_PCI1_MMIO_BASE 0x90000000
+#define CFG_PCI1_MMIO_PHYS CFG_PCI1_MMIO_BASE
+#define CFG_PCI1_MMIO_SIZE 0x10000000 /* 256M */
#define CFG_PCI1_IO_BASE 0x00000000
-#define CFG_PCI1_IO_PHYS 0xe2000000
-#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
+#define CFG_PCI1_IO_PHYS 0xE2000000
+#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */
#define CFG_PCI2_MEM_BASE 0xA0000000
#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
-#define CFG_PCI2_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PCI2_MEM_SIZE 0x10000000 /* 256M */
+#define CFG_PCI2_MMIO_BASE 0xB0000000
+#define CFG_PCI2_MMIO_PHYS CFG_PCI2_MMIO_BASE
+#define CFG_PCI2_MMIO_SIZE 0x10000000 /* 256M */
#define CFG_PCI2_IO_BASE 0x00000000
-#define CFG_PCI2_IO_PHYS 0xe3000000
-#define CFG_PCI2_IO_SIZE 0x1000000 /* 16M */
+#define CFG_PCI2_IO_PHYS 0xE2100000
+#define CFG_PCI2_IO_SIZE 0x00100000 /* 1M */
#if defined(CONFIG_PCI)
-#define PCI_ALL_PCI1
+#define PCI_ONE_PCI1
#if defined(PCI_64BIT)
#undef PCI_ALL_PCI1
#undef PCI_TWO_PCI1
@@ -512,35 +509,35 @@
#define CFG_HRCW_LOW (\
HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
HRCWL_DDR_TO_SCB_CLK_1X1 |\
- HRCWL_CSB_TO_CLKIN_4X1 |\
+ HRCWL_CSB_TO_CLKIN |\
HRCWL_VCO_1X2 |\
HRCWL_CORE_TO_CSB_2X1)
#elif 0 /*396/132*/
#define CFG_HRCW_LOW (\
HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
HRCWL_DDR_TO_SCB_CLK_1X1 |\
- HRCWL_CSB_TO_CLKIN_2X1 |\
+ HRCWL_CSB_TO_CLKIN |\
HRCWL_VCO_1X4 |\
HRCWL_CORE_TO_CSB_3X1)
#elif 0 /*264/132*/
#define CFG_HRCW_LOW (\
HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
HRCWL_DDR_TO_SCB_CLK_1X1 |\
- HRCWL_CSB_TO_CLKIN_2X1 |\
+ HRCWL_CSB_TO_CLKIN |\
HRCWL_VCO_1X4 |\
HRCWL_CORE_TO_CSB_2X1)
#elif 0 /*132/132*/
#define CFG_HRCW_LOW (\
HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
HRCWL_DDR_TO_SCB_CLK_1X1 |\
- HRCWL_CSB_TO_CLKIN_2X1 |\
+ HRCWL_CSB_TO_CLKIN |\
HRCWL_VCO_1X4 |\
HRCWL_CORE_TO_CSB_1X1)
#elif 0 /*264/264 */
#define CFG_HRCW_LOW (\
HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
HRCWL_DDR_TO_SCB_CLK_1X1 |\
- HRCWL_CSB_TO_CLKIN_4X1 |\
+ HRCWL_CSB_TO_CLKIN |\
HRCWL_VCO_1X4 |\
HRCWL_CORE_TO_CSB_1X1)
#endif
@@ -578,7 +575,7 @@
#define CFG_SICRL SICRL_LDP_A
#define CFG_HID0_INIT 0x000000000
-#define CFG_HID0_FINAL CFG_HID0_INIT
+#define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK
/* #define CFG_HID0_FINAL (\
HID0_ENABLE_INSTRUCTION_CACHE |\
@@ -605,25 +602,28 @@
#define CFG_IBAT2U (0)
#endif
-/* IMMRBAR @ 0xE0000000 */
-#define CFG_IBAT3L (CFG_IMMRBAR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT3U (CFG_IMMRBAR | BATU_BL_1M | BATU_VS | BATU_VP)
+#ifdef CONFIG_MPC83XX_PCI2
+#define CFG_IBAT3L (CFG_PCI2_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT3U (CFG_PCI2_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_IBAT4L (CFG_PCI2_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT4U (CFG_PCI2_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#else
+#define CFG_IBAT3L (0)
+#define CFG_IBAT3U (0)
+#define CFG_IBAT4L (0)
+#define CFG_IBAT4U (0)
+#endif
-/* stack in DCACHE (no backing mem) @ 0xE8000000 */
-#define CFG_IBAT4L (CFG_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT4U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
+#define CFG_IBAT5L (CFG_IMMRBAR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT5U (CFG_IMMRBAR | BATU_BL_256M | BATU_VS | BATU_VP)
-/* LBC SDRAM @ 0xF0000000 */
-#define CFG_IBAT5L (CFG_LBC_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT5U (CFG_LBC_SDRAM_BASE | BATU_BL_64M | BATU_VS | BATU_VP)
+/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
+#define CFG_IBAT6L (0xF0000000 | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-/* BCSR @ 0xF8000000 */
-#define CFG_IBAT6L (CFG_BCSR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT6U (CFG_BCSR | BATU_BL_128K | BATU_VS | BATU_VP)
-
-/* FLASH @ 0xFE000000 */
-#define CFG_IBAT7L (CFG_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT7U (CFG_FLASH_BASE | BATU_BL_8M | BATU_VS | BATU_VP)
+#define CFG_IBAT7L (0)
+#define CFG_IBAT7U (0)
#define CFG_DBAT0L CFG_IBAT0L
#define CFG_DBAT0U CFG_IBAT0U
diff --git a/include/configs/delta.h b/include/configs/delta.h
index e4c8cca..91284fd 100644
--- a/include/configs/delta.h
+++ b/include/configs/delta.h
@@ -66,6 +66,17 @@
#define CFG_I2C_INIT_BOARD 1
/* #define CONFIG_HW_WATCHDOG 1 /\* Required for hitting the DA9030 WD *\/ */
+#define DELTA_CHECK_KEYBD 1 /* check for keys pressed during boot */
+#define CONFIG_PREBOOT "\0"
+
+#ifdef DELTA_CHECK_KEYBD
+# define KEYBD_DATALEN 4 /* we have four keys */
+# define KEYBD_KP_DKIN0 0x1 /* vol+ */
+# define KEYBD_KP_DKIN1 0x2 /* vol- */
+# define KEYBD_KP_DKIN2 0x3 /* multi */
+# define KEYBD_KP_DKIN5 0x4 /* SWKEY_GN */
+#endif /* DELTA_CHECK_KEYBD */
+
/*
* select serial console configuration
*/
diff --git a/include/configs/mcc200.h b/include/configs/mcc200.h
index 2b1c0d0..d8d63a1 100644
--- a/include/configs/mcc200.h
+++ b/include/configs/mcc200.h
@@ -172,6 +172,10 @@
#define CONFIG_ENV_OVERWRITE 1 /* allow modification of vendor params */
+#if TEXT_BASE == CFG_FLASH_BASE
+#define CFG_LOWBOOT 1
+#endif
+
/*
* Memory map
*/
diff --git a/include/configs/r5200.h b/include/configs/r5200.h
new file mode 100644
index 0000000..7049704
--- /dev/null
+++ b/include/configs/r5200.h
@@ -0,0 +1,169 @@
+/*
+ * Configuation settings for the R5200 board
+ *
+ * (C) Copyright 2006 Lab X Technologies <zachary.landau@labxtechnologies.com>
+ * Based on Motorola MC5272C3 board config
+ * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef _R5200_H
+#define _R5200_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_MCF52x2 /* define processor family */
+#define CONFIG_M5271 /* define processor type */
+#define CONFIG_R5200 /* define board type */
+
+#define FEC_ENET
+#define CONFIG_NET_RETRY_COUNT 5
+
+#define CONFIG_IPADDR 192.168.0.172
+#define CONFIG_SERVERIP 192.168.0.148
+#define CONFIG_ETHADDR 00:06:3b:00:44:55
+
+#define CONFIG_BAUDRATE 19200
+#define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
+
+#define CONFIG_WATCHDOG
+#define CONFIG_WATCHDOG_TIMEOUT 0xFFFF /* clock modulus */
+
+/* Configuration for environment
+ * Environment is embedded in u-boot in the second sector of the flash
+ */
+#ifndef CONFIG_MONITOR_IS_IN_RAM
+#define CFG_ENV_OFFSET 0x20000
+#define CFG_ENV_SECT_SIZE 0x20000
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_IS_EMBEDDED 1
+#else
+#define CFG_ENV_ADDR 0xf0020000
+#define CFG_ENV_SECT_SIZE 0x2000
+#define CFG_ENV_IS_IN_FLASH 1
+#endif
+
+#define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PING | CFG_CMD_NET ) & ~(CFG_CMD_LOADS | CFG_CMD_LOADB))
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/* Note: We only copy one sectors worth of application code from location
+ * 10200000 for speed purposes. Increase the size if necessary */
+#define CONFIG_BOOTCOMMAND "cp.b 10200000 0 20000; go 400"
+#define CONFIG_BOOTDELAY 1
+
+#define CFG_PROMPT "u-boot> "
+#define CFG_LONGHELP /* undef to save memory */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_LOAD_ADDR 0x00002000
+
+#define CFG_MEMTEST_START 0x400
+#define CFG_MEMTEST_END 0x380000
+
+#define CFG_HZ 1000000
+#define CFG_CLK 100000000
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+
+#define CFG_MBAR 0x40000000 /* Register Base Addrs */
+
+#define CFG_ENET_BD_BASE 0x480000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR 0x20000000
+#define CFG_INIT_RAM_END 0x1000 /* End of used area in internal SRAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_SDRAM_SIZE 8 /* SDRAM size in MB */
+#define CFG_FLASH_BASE 0x10000000
+
+#ifdef CONFIG_MONITOR_IS_IN_RAM
+#define CFG_MONITOR_BASE 0x20000
+#else
+#define CFG_MONITOR_BASE (CFG_FLASH_BASE + 0x400)
+#endif
+
+#define CFG_MONITOR_LEN 0x20001
+#define CFG_MALLOC_LEN (256 << 10)
+#define CFG_BOOTPARAMS_LEN 64*1024
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization ??
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 1024 /* max number of sectors on one chip */
+#define CFG_FLASH_ERASE_TOUT 1000
+
+#define CFG_FLASH_CFI 1
+#define CFG_FLASH_CFI_DRIVER 1
+#define CFG_FLASH_SIZE 0x800000
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 16
+
+/*-----------------------------------------------------------------------
+ * Memory bank definitions
+ */
+
+/*-----------------------------------------------------------------------
+ * Port configuration
+ */
+#define CFG_FECI2C 0xF0
+
+#endif /* _R5200_H */
diff --git a/include/configs/zylonite.h b/include/configs/zylonite.h
index 4232d50..c6aa8ec 100644
--- a/include/configs/zylonite.h
+++ b/include/configs/zylonite.h
@@ -76,14 +76,17 @@
#define CONFIG_BAUDRATE 115200
-/* #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_MMC | CFG_CMD_FAT) */
#ifdef TURN_ON_ETHERNET
# define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PING)
#else
-# define CONFIG_COMMANDS (CONFIG_CMD_DFL & ~CFG_CMD_NET)
+# define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
+ | CFG_CMD_ENV \
+ | CFG_CMD_NAND) \
+ & ~(CFG_CMD_NET \
+ | CFG_CMD_FLASH \
+ | CFG_CMD_IMLS))
#endif
-
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
@@ -127,8 +130,11 @@
#define CFG_LOAD_ADDR (CFG_DRAM_BASE + 0x8000) /* default load address */
-#define CFG_HZ 3686400 /* incrementer freq: 3.6864 MHz */
-#define CFG_CPUSPEED 0x161 /* set core clock to 400/200/100 MHz */
+#define CFG_HZ 3250000 /* incrementer freq: 3.25 MHz */
+
+/* Monahans Core Frequency */
+#define CFG_MONAHANS_RUN_MODE_OSC_RATIO 16 /* valid values: 8, 16, 24, 31 */
+#define CFG_MONAHANS_TURBO_RUN_MODE_RATIO 1 /* valid values: 1, 2 */
/* valid baudrates */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
@@ -159,98 +165,64 @@
#define PHYS_SDRAM_4 0xac000000 /* SDRAM Bank #4 */
#define PHYS_SDRAM_4_SIZE 0x00000000 /* 0 MB */
-#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
-#define PHYS_FLASH_2 0x04000000 /* Flash Bank #2 */
-#define PHYS_FLASH_SIZE 0x02000000 /* 32 MB */
-#define PHYS_FLASH_BANK_SIZE 0x02000000 /* 32 MB Banks */
-#define PHYS_FLASH_SECT_SIZE 0x00040000 /* 256 KB sectors (x2) */
+#define CFG_DRAM_BASE 0x80000000 /* at CS0 */
+#define CFG_DRAM_SIZE 0x04000000 /* 64 MB Ram */
-#define CFG_DRAM_BASE 0xa0000000
-#define CFG_DRAM_SIZE 0x04000000
-
-#define CFG_FLASH_BASE PHYS_FLASH_1
-
-#define FPGA_REGS_BASE_PHYSICAL 0x08000000
-
-/*
- * GPIO settings
- */
-#define CFG_GPSR0_VAL 0x00008000
-#define CFG_GPSR1_VAL 0x00FC0382
-#define CFG_GPSR2_VAL 0x0001FFFF
-#define CFG_GPCR0_VAL 0x00000000
-#define CFG_GPCR1_VAL 0x00000000
-#define CFG_GPCR2_VAL 0x00000000
-#define CFG_GPDR0_VAL 0x0060A800
-#define CFG_GPDR1_VAL 0x00FF0382
-#define CFG_GPDR2_VAL 0x0001C000
-#define CFG_GAFR0_L_VAL 0x98400000
-#define CFG_GAFR0_U_VAL 0x00002950
-#define CFG_GAFR1_L_VAL 0x000A9558
-#define CFG_GAFR1_U_VAL 0x0005AAAA
-#define CFG_GAFR2_L_VAL 0xA0000000
-#define CFG_GAFR2_U_VAL 0x00000002
-
-#define CFG_PSSR_VAL 0x20
-
-/*
- * Memory settings
- */
-#define CFG_MSC0_VAL 0x23F223F2
-#define CFG_MSC1_VAL 0x3FF1A441
-#define CFG_MSC2_VAL 0x7FF97FF1
-#define CFG_MDCNFG_VAL 0x00001AC9
-#define CFG_MDREFR_VAL 0x00018018
-#define CFG_MDMRS_VAL 0x00000000
-
-/*
- * PCMCIA and CF Interfaces
- */
-#define CFG_MECR_VAL 0x00000000
-#define CFG_MCMEM0_VAL 0x00010504
-#define CFG_MCMEM1_VAL 0x00010504
-#define CFG_MCATT0_VAL 0x00010504
-#define CFG_MCATT1_VAL 0x00010504
-#define CFG_MCIO0_VAL 0x00004715
-#define CFG_MCIO1_VAL 0x00004715
-
-#define _LED 0x08000010
-#define LED_BLANK 0x08000040
-
-/*
- * FLASH and environment organization
- */
-#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
-
-/* timeout values are in ticks */
-#define CFG_FLASH_ERASE_TOUT (25*CFG_HZ) /* Timeout for Flash Erase */
-#define CFG_FLASH_WRITE_TOUT (25*CFG_HZ) /* Timeout for Flash Write */
-
-/* NOTE: many default partitioning schemes assume the kernel starts at the
- * second sector, not an environment. You have been warned!
- */
-#define CFG_MONITOR_LEN PHYS_FLASH_SECT_SIZE
-
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_ADDR (PHYS_FLASH_1 + PHYS_FLASH_SECT_SIZE)
-#define CFG_ENV_SECT_SIZE PHYS_FLASH_SECT_SIZE
-#define CFG_ENV_SIZE (PHYS_FLASH_SECT_SIZE / 16)
+#undef CFG_SKIP_DRAM_SCRUB
/*
- * FPGA Offsets
+ * NAND Flash
*/
-#define WHOAMI_OFFSET 0x00
-#define HEXLED_OFFSET 0x10
-#define BLANKLED_OFFSET 0x40
-#define DISCRETELED_OFFSET 0x40
-#define CNFG_SWITCHES_OFFSET 0x50
-#define USER_SWITCHES_OFFSET 0x60
-#define MISC_WR_OFFSET 0x80
-#define MISC_RD_OFFSET 0x90
-#define INT_MASK_OFFSET 0xC0
-#define INT_CLEAR_OFFSET 0xD0
-#define GP_OFFSET 0x100
+/* Use the new NAND code. (BOARDLIBS = drivers/nand/libnand.a required) */
+#define CONFIG_NEW_NAND_CODE
+#define CFG_NAND0_BASE 0x0
+#undef CFG_NAND1_BASE
+
+#define CFG_NAND_BASE_LIST { CFG_NAND0_BASE }
+#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
+
+/* nand timeout values */
+#define CFG_NAND_PROG_ERASE_TO 3000
+#define CFG_NAND_OTHER_TO 100
+#define CFG_NAND_SENDCMD_RETRY 3
+#undef NAND_ALLOW_ERASE_ALL /* Allow erasing bad blocks - don't use */
+
+/* NAND Timing Parameters (in ns) */
+#define NAND_TIMING_tCH 10
+#define NAND_TIMING_tCS 0
+#define NAND_TIMING_tWH 20
+#define NAND_TIMING_tWP 40
+
+#define NAND_TIMING_tRH 20
+#define NAND_TIMING_tRP 40
+
+#define NAND_TIMING_tR 11123
+#define NAND_TIMING_tWHR 100
+#define NAND_TIMING_tAR 10
+
+/* NAND debugging */
+#define CFG_DFC_DEBUG1 /* usefull */
+#undef CFG_DFC_DEBUG2 /* noisy */
+#undef CFG_DFC_DEBUG3 /* extremly noisy */
+
+#define CONFIG_MTD_DEBUG
+#define CONFIG_MTD_DEBUG_VERBOSE 1
+
+#define ADDR_COLUMN 1
+#define ADDR_PAGE 2
+#define ADDR_COLUMN_PAGE 3
+
+#define NAND_ChipID_UNKNOWN 0x00
+#define NAND_MAX_FLOORS 1
+#define NAND_MAX_CHIPS 1
+
+#define CFG_NO_FLASH 1
+
+#define CFG_ENV_IS_IN_NAND 1
+#define CFG_ENV_OFFSET 0x40000
+#define CFG_ENV_OFFSET_REDUND 0x44000
+#define CFG_ENV_SIZE 0x4000
+
#endif /* __CONFIG_H */
diff --git a/include/linux/string.h b/include/linux/string.h
index 1a45fd3..6239039 100644
--- a/include/linux/string.h
+++ b/include/linux/string.h
@@ -38,7 +38,7 @@
#ifndef __HAVE_ARCH_STRNCMP
extern int strncmp(const char *,const char *,__kernel_size_t);
#endif
-#ifndef __HAVE_ARCH_STRNICMP
+#if 0 /* not used - was: #ifndef __HAVE_ARCH_STRNICMP */
extern int strnicmp(const char *, const char *, __kernel_size_t);
#endif
#ifndef __HAVE_ARCH_STRCHR
diff --git a/lib_arm/board.c b/lib_arm/board.c
index 1028b04..babc254 100644
--- a/lib_arm/board.c
+++ b/lib_arm/board.c
@@ -297,7 +297,7 @@
mem_malloc_init (_armboot_start - CFG_MALLOC_LEN);
#if (CONFIG_COMMANDS & CFG_CMD_NAND)
- puts ("NAND:");
+ puts ("NAND: ");
nand_init(); /* go init the NAND */
#endif
diff --git a/lib_generic/string.c b/lib_generic/string.c
index 0e99d1b..e0b793a 100644
--- a/lib_generic/string.c
+++ b/lib_generic/string.c
@@ -21,7 +21,7 @@
#include <malloc.h>
-#ifndef __HAVE_ARCH_STRNICMP
+#if 0 /* not used - was: #ifndef __HAVE_ARCH_STRNICMP */
/**
* strnicmp - Case insensitive, length-limited string comparison
* @s1: One string
diff --git a/lib_m68k/board.c b/lib_m68k/board.c
index e25833b..73d2e3f 100644
--- a/lib_m68k/board.c
+++ b/lib_m68k/board.c
@@ -261,6 +261,7 @@
{
bd_t *bd;
ulong len, addr, addr_sp;
+ ulong *paddr;
gd_t *id;
init_fnc_t **init_fnc_ptr;
#ifdef CONFIG_PRAM
@@ -357,8 +358,12 @@
*/
addr_sp -= 16;
addr_sp &= ~0xF;
- *((ulong *) addr_sp)-- = 0;
- *((ulong *) addr_sp)-- = 0;
+
+ paddr = (ulong *)addr_sp;
+ *paddr-- = 0;
+ *paddr-- = 0;
+ addr_sp = (ulong)paddr;
+
debug ("Stack Pointer at: %08lx\n", addr_sp);
/*
@@ -631,7 +636,7 @@
#if (CONFIG_COMMANDS & CFG_CMD_NAND)
WATCHDOG_RESET ();
- puts ("NAND:");
+ puts ("NAND: ");
nand_init(); /* go init the NAND */
#endif
diff --git a/lib_m68k/time.c b/lib_m68k/time.c
index 1d6d297..d45e470 100644
--- a/lib_m68k/time.c
+++ b/lib_m68k/time.c
@@ -27,6 +27,11 @@
#include <asm/mcftimer.h>
+#ifdef CONFIG_M5271
+#include <asm/m5271.h>
+#include <asm/immap_5271.h>
+#endif
+
#ifdef CONFIG_M5272
#include <asm/m5272.h>
#include <asm/immap_5272.h>
@@ -43,7 +48,7 @@
static ulong timestamp;
-#ifdef CONFIG_M5282
+#if defined(CONFIG_M5282) || defined(CONFIG_M5271)
static unsigned short lastinc;
#endif
@@ -127,7 +132,7 @@
}
#endif
-#if defined(CONFIG_M5282)
+#if defined(CONFIG_M5282) || defined(CONFIG_M5271)
void udelay(unsigned long usec)
{
diff --git a/rtc/ds1306.c b/rtc/ds1306.c
index e143bf7..e01e1ce 100644
--- a/rtc/ds1306.c
+++ b/rtc/ds1306.c
@@ -360,13 +360,13 @@
tmp->tm_year, tmp->tm_mon, tmp->tm_mday, tmp->tm_wday,
tmp->tm_hour, tmp->tm_min, tmp->tm_sec);
- rtc_write (RTC_YEAR, bin2bcd (tmp->tm_year - 2000));
- rtc_write (RTC_MONTH, bin2bcd (tmp->tm_mon));
- rtc_write (RTC_DATE_OF_MONTH, bin2bcd (tmp->tm_mday));
- rtc_write (RTC_DAY_OF_WEEK, bin2bcd (tmp->tm_wday + 1));
- rtc_write (RTC_HOURS, bin2bcd (tmp->tm_hour));
- rtc_write (RTC_MINUTES, bin2bcd (tmp->tm_min));
rtc_write (RTC_SECONDS, bin2bcd (tmp->tm_sec));
+ rtc_write (RTC_MINUTES, bin2bcd (tmp->tm_min));
+ rtc_write (RTC_HOURS, bin2bcd (tmp->tm_hour));
+ rtc_write (RTC_DAY_OF_WEEK, bin2bcd (tmp->tm_wday + 1));
+ rtc_write (RTC_DATE_OF_MONTH, bin2bcd (tmp->tm_mday));
+ rtc_write (RTC_MONTH, bin2bcd (tmp->tm_mon));
+ rtc_write (RTC_YEAR, bin2bcd (tmp->tm_year - 2000));
}
/* ------------------------------------------------------------------------- */
diff --git a/tools/mkimage.c b/tools/mkimage.c
index 5222bb2..fea3e5b 100644
--- a/tools/mkimage.c
+++ b/tools/mkimage.c
@@ -277,7 +277,8 @@
*/
if (xflag) {
if (ep != addr + sizeof(image_header_t)) {
- fprintf (stderr, "%s: For XIP, the entry point must be the load addr + %lu\n",
+ fprintf (stderr,
+ "%s: For XIP, the entry point must be the load addr + %lu\n",
cmdname,
(unsigned long)sizeof(image_header_t));
exit (EXIT_FAILURE);
@@ -347,8 +348,9 @@
if (crc32 (0, data, len) != checksum) {
fprintf (stderr,
- "*** Warning: \"%s\" has bad header checksum!\n",
- imagefile);
+ "%s: ERROR: \"%s\" has bad header checksum!\n",
+ cmdname, imagefile);
+ exit (EXIT_FAILURE);
}
data = (char *)(ptr + sizeof(image_header_t));
@@ -356,8 +358,9 @@
if (crc32 (0, data, len) != ntohl(hdr->ih_dcrc)) {
fprintf (stderr,
- "*** Warning: \"%s\" has corrupted data!\n",
- imagefile);
+ "%s: ERROR: \"%s\" has corrupted data!\n",
+ cmdname, imagefile);
+ exit (EXIT_FAILURE);
}
/* for multi-file images we need the data part, too */