drivers: misc: add Gateworks System Controller driver
Add a driver for the Gateworks System Controller used on Gateworks boards
which provides a boot watchdog, power control, temperature monitor,
and voltage ADCs.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
diff --git a/MAINTAINERS b/MAINTAINERS
index cf060da..bde298c 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -882,6 +882,12 @@
F: drivers/watchdog/sp805_wdt.c
F: drivers/watchdog/sbsa_gwdt.c
+GATEWORKS_SC
+M: Tim Harvey <tharvey@gateworks.com>
+S: Maintained
+F: drivers/misc/gsc.c
+F: include/gsc.h
+
I2C
M: Heiko Schocher <hs@denx.de>
S: Maintained
diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
index 7029bb7..10fd601 100644
--- a/drivers/misc/Kconfig
+++ b/drivers/misc/Kconfig
@@ -46,6 +46,14 @@
CryptoAuthentication module found for example on the Turris Omnia
board.
+config GATEWORKS_SC
+ bool "Gateworks System Controller Support"
+ depends on MISC
+ help
+ Enable access for the Gateworks System Controller used on Gateworks
+ boards to provide a boot watchdog, power control, temperature monitor,
+ voltage ADCs, and EEPROM.
+
config ROCKCHIP_EFUSE
bool "Rockchip e-fuse support"
depends on MISC
diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile
index f22eff6..6150d01 100644
--- a/drivers/misc/Makefile
+++ b/drivers/misc/Makefile
@@ -38,6 +38,7 @@
obj-$(CONFIG_FSL_MC9SDZ60) += mc9sdz60.o
obj-$(CONFIG_FSL_SEC_MON) += fsl_sec_mon.o
obj-$(CONFIG_$(SPL_)FS_LOADER) += fs_loader.o
+obj-$(CONFIG_GATEWORKS_SC) += gsc.o
obj-$(CONFIG_GDSYS_IOEP) += gdsys_ioep.o
obj-$(CONFIG_GDSYS_RXAUI_CTRL) += gdsys_rxaui_ctrl.o
obj-$(CONFIG_GDSYS_SOC) += gdsys_soc.o
diff --git a/drivers/misc/gsc.c b/drivers/misc/gsc.c
new file mode 100644
index 0000000..ec24ca8
--- /dev/null
+++ b/drivers/misc/gsc.c
@@ -0,0 +1,633 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2022 Gateworks Corporation
+ */
+
+#include <command.h>
+#include <gsc.h>
+#include <i2c.h>
+#include <rtc.h>
+#include <asm/unaligned.h>
+#include <linux/delay.h>
+#include <dm/device.h>
+#include <dm/device-internal.h>
+#include <dm/ofnode.h>
+#include <dm/read.h>
+
+#define GSC_BUSNO 0
+#define GSC_SC_ADDR 0x20
+#define GSC_HWMON_ADDR 0x29
+#define GSC_RTC_ADDR 0x68
+
+/* System Controller registers */
+enum {
+ GSC_SC_CTRL0 = 0,
+ GSC_SC_CTRL1 = 1,
+ GSC_SC_TIME = 2,
+ GSC_SC_TIME_ADD = 6,
+ GSC_SC_STATUS = 10,
+ GSC_SC_FWCRC = 12,
+ GSC_SC_FWVER = 14,
+ GSC_SC_WP = 15,
+ GSC_SC_RST_CAUSE = 16,
+ GSC_SC_THERM_PROTECT = 19,
+};
+
+/* System Controller Control1 bits */
+enum {
+ GSC_SC_CTRL1_SLEEP_EN = 0, /* 1 = enable sleep */
+ GSC_SC_CTRL1_SLEEP_ACTIVATE = 1, /* 1 = activate sleep */
+ GSC_SC_CTRL1_SLEEP_ADD = 2, /* 1 = latch and add sleep time */
+ GSC_SC_CTRL1_SLEEP_NOWAKEPB = 3, /* 1 = do not wake on sleep on button press */
+ GSC_SC_CTRL1_WDTIME = 4, /* 1 = 60s timeout, 0 = 30s timeout */
+ GSC_SC_CTRL1_WDEN = 5, /* 1 = enable, 0 = disable */
+ GSC_SC_CTRL1_BOOT_CHK = 6, /* 1 = enable alt boot check */
+ GSC_SC_CTRL1_WDDIS = 7, /* 1 = disable boot watchdog */
+};
+
+/* System Controller Interrupt bits */
+enum {
+ GSC_SC_IRQ_PB = 0, /* Pushbutton switch */
+ GSC_SC_IRQ_SECURE = 1, /* Secure Key erase operation complete */
+ GSC_SC_IRQ_EEPROM_WP = 2, /* EEPROM write violation */
+ GSC_SC_IRQ_GPIO = 4, /* GPIO change */
+ GSC_SC_IRQ_TAMPER = 5, /* Tamper detect */
+ GSC_SC_IRQ_WATCHDOG = 6, /* Watchdog trip */
+ GSC_SC_IRQ_PBLONG = 7, /* Pushbutton long hold */
+};
+
+/* System Controller WP bits */
+enum {
+ GSC_SC_WP_ALL = 0, /* Write Protect All EEPROM regions */
+ GSC_SC_WP_BOARDINFO = 1, /* Write Protect Board Info region */
+};
+
+/* System Controller Reset Cause */
+enum {
+ GSC_SC_RST_CAUSE_VIN = 0,
+ GSC_SC_RST_CAUSE_PB = 1,
+ GSC_SC_RST_CAUSE_WDT = 2,
+ GSC_SC_RST_CAUSE_CPU = 3,
+ GSC_SC_RST_CAUSE_TEMP_LOCAL = 4,
+ GSC_SC_RST_CAUSE_TEMP_REMOTE = 5,
+ GSC_SC_RST_CAUSE_SLEEP = 6,
+ GSC_SC_RST_CAUSE_BOOT_WDT = 7,
+ GSC_SC_RST_CAUSE_BOOT_WDT_MAN = 8,
+ GSC_SC_RST_CAUSE_SOFT_PWR = 9,
+ GSC_SC_RST_CAUSE_MAX = 10,
+};
+
+#if (IS_ENABLED(CONFIG_DM_I2C))
+
+struct gsc_priv {
+ int gscver;
+ int fwver;
+ int fwcrc;
+ struct udevice *hwmon;
+ struct udevice *rtc;
+};
+
+/*
+ * GSCv2 will fail to ACK an I2C transaction if it is busy, which can occur
+ * during its 1HZ timer tick while reading ADC's. When this does occur,
+ * it will never be busy longer than 2 back-to-back transfers so retry 3 times.
+ */
+static int gsc_i2c_read(struct udevice *dev, uint addr, u8 *buf, int len)
+{
+ struct gsc_priv *priv = dev_get_priv(dev);
+ int retry = (priv->gscver == 3) ? 1 : 3;
+ int n = 0;
+ int ret;
+
+ while (n++ < retry) {
+ ret = dm_i2c_read(dev, addr, buf, len);
+ if (!ret)
+ break;
+ if (ret != -EREMOTEIO)
+ break;
+ mdelay(10);
+ }
+ return ret;
+}
+
+static int gsc_i2c_write(struct udevice *dev, uint addr, const u8 *buf, int len)
+{
+ struct gsc_priv *priv = dev_get_priv(dev);
+ int retry = (priv->gscver == 3) ? 1 : 3;
+ int n = 0;
+ int ret;
+
+ while (n++ < retry) {
+ ret = dm_i2c_write(dev, addr, buf, len);
+ if (!ret)
+ break;
+ if (ret != -EREMOTEIO)
+ break;
+ mdelay(10);
+ }
+ return ret;
+}
+
+static struct udevice *gsc_get_dev(int busno, int slave)
+{
+ struct udevice *dev, *bus;
+ int ret;
+
+ ret = uclass_get_device_by_seq(UCLASS_I2C, busno, &bus);
+ if (ret)
+ return NULL;
+ ret = dm_i2c_probe(bus, slave, 0, &dev);
+ if (ret)
+ return NULL;
+
+ return dev;
+}
+
+static int gsc_thermal_get_info(struct udevice *dev, u8 *outreg, int *tmax, bool *enable)
+{
+ struct gsc_priv *priv = dev_get_priv(dev);
+ int ret;
+ u8 reg;
+
+ if (priv->gscver > 2 && priv->fwver > 52) {
+ ret = gsc_i2c_read(dev, GSC_SC_THERM_PROTECT, ®, 1);
+ if (!ret) {
+ if (outreg)
+ *outreg = reg;
+ if (tmax) {
+ *tmax = ((reg & 0xf8) >> 3) * 2;
+ if (*tmax)
+ *tmax += 70;
+ else
+ *tmax = 120;
+ }
+ if (enable)
+ *enable = reg & 1;
+ }
+ } else {
+ ret = -ENODEV;
+ }
+
+ return ret;
+}
+
+static int gsc_thermal_get_temp(struct udevice *dev)
+{
+ struct gsc_priv *priv = dev_get_priv(dev);
+ u32 reg, mode, val;
+ const char *label;
+ ofnode node;
+ u8 buf[2];
+
+ ofnode_for_each_subnode(node, dev_read_subnode(dev, "adc")) {
+ if (ofnode_read_u32(node, "reg", ®))
+ reg = -1;
+ if (ofnode_read_u32(node, "gw,mode", &mode))
+ mode = -1;
+ label = ofnode_read_string(node, "label");
+
+ if ((reg == -1) || (mode == -1) || !label)
+ continue;
+
+ if (mode != 0 || strcmp(label, "temp"))
+ continue;
+
+ memset(buf, 0, sizeof(buf));
+ if (!gsc_i2c_read(priv->hwmon, reg, buf, sizeof(buf))) {
+ val = buf[0] | buf[1] << 8;
+ if (val > 0x8000)
+ val -= 0xffff;
+ return val;
+ }
+ }
+
+ return 0;
+}
+
+static void gsc_thermal_info(struct udevice *dev)
+{
+ struct gsc_priv *priv = dev_get_priv(dev);
+
+ switch (priv->gscver) {
+ case 2:
+ printf("board_temp:%dC ", gsc_thermal_get_temp(dev) / 10);
+ break;
+ case 3:
+ if (priv->fwver > 52) {
+ bool enabled;
+ int tmax;
+
+ if (!gsc_thermal_get_info(dev, NULL, &tmax, &enabled)) {
+ puts("Thermal protection:");
+ if (enabled)
+ printf("enabled at %dC ", tmax);
+ else
+ puts("disabled ");
+ }
+ }
+ break;
+ }
+}
+
+static void gsc_reset_info(struct udevice *dev)
+{
+ struct gsc_priv *priv = dev_get_priv(dev);
+ static const char * const names[] = {
+ "VIN",
+ "PB",
+ "WDT",
+ "CPU",
+ "TEMP_L",
+ "TEMP_R",
+ "SLEEP",
+ "BOOT_WDT1",
+ "BOOT_WDT2",
+ "SOFT_PWR",
+ };
+ u8 reg;
+
+ /* reset cause */
+ switch (priv->gscver) {
+ case 2:
+ if (!gsc_i2c_read(dev, GSC_SC_STATUS, ®, 1)) {
+ if (reg & BIT(GSC_SC_IRQ_WATCHDOG)) {
+ puts("RST:WDT");
+ reg &= ~BIT(GSC_SC_IRQ_WATCHDOG);
+ gsc_i2c_write(dev, GSC_SC_STATUS, ®, 1);
+ } else {
+ puts("RST:VIN");
+ }
+ printf(" WDT:%sabled ",
+ (reg & BIT(GSC_SC_CTRL1_WDEN)) ? "en" : "dis");
+ }
+ break;
+ case 3:
+ if (priv->fwver > 52 &&
+ !gsc_i2c_read(dev, GSC_SC_RST_CAUSE, ®, 1)) {
+ puts("RST:");
+ if (reg < ARRAY_SIZE(names))
+ printf("%s ", names[reg]);
+ else
+ printf("0x%02x ", reg);
+ }
+ break;
+ }
+}
+
+/* display hardware monitor ADC channels */
+static int gsc_hwmon(struct udevice *dev)
+{
+ struct gsc_priv *priv = dev_get_priv(dev);
+ u32 reg, mode, val, offset;
+ const char *label;
+ ofnode node;
+ u8 buf[2];
+ u32 r[2];
+ int ret;
+
+ /* iterate over hwmon nodes */
+ ofnode_for_each_subnode(node, dev_read_subnode(dev, "adc")) {
+ if (ofnode_read_u32(node, "reg", ®))
+ reg = -1;
+ if (ofnode_read_u32(node, "gw,mode", &mode))
+ mode = -1;
+ label = ofnode_read_string(node, "label");
+ if ((reg == -1) || (mode == -1) || !label)
+ continue;
+
+ memset(buf, 0, sizeof(buf));
+ ret = gsc_i2c_read(priv->hwmon, reg, buf, sizeof(buf));
+ if (ret) {
+ printf("i2c error: %d\n", ret);
+ continue;
+ }
+ val = buf[0] | buf[1] << 8;
+
+ switch (mode) {
+ case 0: /* temperature (C*10) */
+ if (val > 0x8000)
+ val -= 0xffff;
+ printf("%-8s: %d.%ldC\n", label, val / 10, abs(val % 10));
+ break;
+ case 1: /* prescaled voltage */
+ if (val != 0xffff)
+ printf("%-8s: %d.%03dV\n", label, val / 1000, val % 1000);
+ break;
+ case 2: /* scaled based on ref volt and resolution */
+ val *= 2500;
+ val /= 1 << 12;
+
+ /* apply pre-scaler voltage divider */
+ if (!ofnode_read_u32_index(node, "gw,voltage-divider-ohms", 0, &r[0]) &&
+ !ofnode_read_u32_index(node, "gw,voltage-divider-ohms", 1, &r[1]) &&
+ r[0] && r[1]) {
+ val *= (r[0] + r[1]);
+ val /= r[1];
+ }
+
+ /* adjust by offset */
+ val += (offset / 1000);
+
+ printf("%-8s: %d.%03dV\n", label, val / 1000, val % 1000);
+ break;
+ }
+ }
+
+ return 0;
+}
+
+static int gsc_banner(struct udevice *dev)
+{
+ struct gsc_priv *priv = dev_get_priv(dev);
+
+ /* banner */
+ printf("GSCv%d : v%d 0x%04x ", priv->gscver, priv->fwver, priv->fwcrc);
+ gsc_reset_info(dev);
+ gsc_thermal_info(dev);
+ puts("\n");
+
+ /* Display RTC */
+ if (priv->rtc) {
+ u8 buf[4];
+ time_t timestamp;
+ struct rtc_time tm;
+
+ if (!gsc_i2c_read(priv->rtc, 0, buf, 4)) {
+ timestamp = get_unaligned_le32(buf);
+ rtc_to_tm(timestamp, &tm);
+ printf("RTC : %4d-%02d-%02d %2d:%02d:%02d UTC\n",
+ tm.tm_year, tm.tm_mon, tm.tm_mday,
+ tm.tm_hour, tm.tm_min, tm.tm_sec);
+ }
+ }
+
+ return 0;
+}
+
+static int gsc_probe(struct udevice *dev)
+{
+ struct gsc_priv *priv = dev_get_priv(dev);
+ u8 buf[32];
+ int ret;
+
+ ret = gsc_i2c_read(dev, 0, buf, sizeof(buf));
+ if (ret)
+ return ret;
+
+ /*
+ * GSC chip version:
+ * GSCv2 has 16 registers (which overlap)
+ * GSCv3 has 32 registers
+ */
+ priv->gscver = memcmp(buf, buf + 16, 16) ? 3 : 2;
+ priv->fwver = buf[GSC_SC_FWVER];
+ priv->fwcrc = buf[GSC_SC_FWCRC] | buf[GSC_SC_FWCRC + 1] << 8;
+ priv->hwmon = gsc_get_dev(GSC_BUSNO, GSC_HWMON_ADDR);
+ if (priv->hwmon)
+ dev_set_priv(priv->hwmon, priv);
+ priv->rtc = gsc_get_dev(GSC_BUSNO, GSC_RTC_ADDR);
+ if (priv->rtc)
+ dev_set_priv(priv->rtc, priv);
+
+#ifdef CONFIG_SPL_BUILD
+ gsc_banner(dev);
+#endif
+
+ return 0;
+};
+
+static const struct udevice_id gsc_ids[] = {
+ { .compatible = "gw,gsc", },
+ { }
+};
+
+U_BOOT_DRIVER(gsc) = {
+ .name = "gsc",
+ .id = UCLASS_MISC,
+ .of_match = gsc_ids,
+ .probe = gsc_probe,
+ .priv_auto = sizeof(struct gsc_priv),
+ .flags = DM_FLAG_PRE_RELOC,
+};
+
+static int gsc_sleep(struct udevice *dev, unsigned long secs)
+{
+ u8 regs[4];
+ int ret;
+
+ printf("GSC Sleeping for %ld seconds\n", secs);
+ put_unaligned_le32(secs, regs);
+ ret = gsc_i2c_write(dev, GSC_SC_TIME_ADD, regs, sizeof(regs));
+ if (ret)
+ goto err;
+ ret = gsc_i2c_read(dev, GSC_SC_CTRL1, regs, 1);
+ if (ret)
+ goto err;
+ regs[0] |= BIT(GSC_SC_CTRL1_SLEEP_ADD);
+ ret = gsc_i2c_write(dev, GSC_SC_CTRL1, regs, 1);
+ if (ret)
+ goto err;
+ regs[0] &= ~BIT(GSC_SC_CTRL1_SLEEP_ADD);
+ regs[0] |= BIT(GSC_SC_CTRL1_SLEEP_EN) | BIT(GSC_SC_CTRL1_SLEEP_ACTIVATE);
+ ret = gsc_i2c_write(dev, GSC_SC_CTRL1, regs, 1);
+ if (ret)
+ goto err;
+
+ return 0;
+
+err:
+ printf("i2c error: %d\n", ret);
+ return ret;
+}
+
+static int gsc_wd_disable(struct udevice *dev)
+{
+ int ret;
+ u8 reg;
+
+ ret = gsc_i2c_read(dev, GSC_SC_CTRL1, ®, 1);
+ if (ret)
+ goto err;
+ reg |= BIT(GSC_SC_CTRL1_WDDIS);
+ reg &= ~BIT(GSC_SC_CTRL1_BOOT_CHK);
+ ret = gsc_i2c_write(dev, GSC_SC_CTRL1, ®, 1);
+ if (ret)
+ goto err;
+ puts("GSC : boot watchdog disabled\n");
+
+ return 0;
+
+err:
+ puts("i2c error");
+ return ret;
+}
+
+static int gsc_thermal(struct udevice *dev, const char *cmd, const char *val)
+{
+ struct gsc_priv *priv = dev_get_priv(dev);
+ int ret, tmax;
+ bool enabled;
+ u8 reg;
+
+ if (priv->gscver < 3 || priv->fwver < 53)
+ return -EINVAL;
+ ret = gsc_thermal_get_info(dev, ®, &tmax, &enabled);
+ if (ret)
+ return ret;
+ if (cmd && !strcmp(cmd, "enable")) {
+ if (val && *val) {
+ tmax = clamp((int)simple_strtoul(val, NULL, 0), 72, 122);
+ reg &= ~0xf8;
+ reg |= ((tmax - 70) / 2) << 3;
+ }
+ reg |= BIT(0);
+ gsc_i2c_write(dev, GSC_SC_THERM_PROTECT, ®, 1);
+ } else if (cmd && !strcmp(cmd, "disable")) {
+ reg &= ~BIT(0);
+ gsc_i2c_write(dev, GSC_SC_THERM_PROTECT, ®, 1);
+ } else if (cmd) {
+ return -EINVAL;
+ }
+
+ /* show status */
+ gsc_thermal_info(dev);
+ puts("\n");
+
+ return 0;
+}
+
+/* override in board files to display additional board EEPROM info */
+__weak void board_gsc_info(void)
+{
+}
+
+static void gsc_info(struct udevice *dev)
+{
+ gsc_banner(dev);
+ board_gsc_info();
+}
+
+static int do_gsc(struct cmd_tbl *cmdtp, int flag, int argc, char * const argv[])
+{
+ struct udevice *dev;
+ int ret;
+
+ /* get/probe driver */
+ ret = uclass_get_device_by_driver(UCLASS_MISC, DM_DRIVER_GET(gsc), &dev);
+ if (ret)
+ return CMD_RET_USAGE;
+ if (argc < 2) {
+ gsc_info(dev);
+ return CMD_RET_SUCCESS;
+ } else if (strcasecmp(argv[1], "sleep") == 0) {
+ if (argc < 3)
+ return CMD_RET_USAGE;
+ if (!gsc_sleep(dev, dectoul(argv[2], NULL)))
+ return CMD_RET_SUCCESS;
+ } else if (strcasecmp(argv[1], "hwmon") == 0) {
+ if (!gsc_hwmon(dev))
+ return CMD_RET_SUCCESS;
+ } else if (strcasecmp(argv[1], "wd-disable") == 0) {
+ if (!gsc_wd_disable(dev))
+ return CMD_RET_SUCCESS;
+ } else if (strcasecmp(argv[1], "thermal") == 0) {
+ char *cmd, *val;
+
+ cmd = (argc > 2) ? argv[2] : NULL;
+ val = (argc > 3) ? argv[3] : NULL;
+ if (!gsc_thermal(dev, cmd, val))
+ return CMD_RET_SUCCESS;
+ }
+
+ return CMD_RET_USAGE;
+}
+
+U_BOOT_CMD(gsc, 4, 1, do_gsc, "Gateworks System Controller",
+ "[sleep <secs>]|[hwmon]|[wd-disable][thermal [disable|enable [temp]]]\n");
+
+/* disable boot watchdog - useful for an SPL that wants to use falcon mode */
+int gsc_boot_wd_disable(void)
+{
+ struct udevice *dev;
+ int ret;
+
+ /* get/probe driver */
+ ret = uclass_get_device_by_driver(UCLASS_MISC, DM_DRIVER_GET(gsc), &dev);
+ if (!ret)
+ ret = gsc_wd_disable(dev);
+
+ return ret;
+}
+
+# else
+
+/*
+ * GSCv2 will fail to ACK an I2C transaction if it is busy, which can occur
+ * during its 1HZ timer tick while reading ADC's. When this does occur,
+ * it will never be busy longer than 2 back-to-back transfers so retry 3 times.
+ */
+static int gsc_i2c_read(uint chip, uint addr, u8 *buf, int len)
+{
+ int retry = 3;
+ int n = 0;
+ int ret;
+
+ while (n++ < retry) {
+ ret = i2c_read(chip, addr, 1, buf, len);
+ if (!ret)
+ break;
+ if (ret != -EREMOTEIO)
+ break;
+printf("%s 0x%02x retry %d\n", __func__, addr, n);
+ mdelay(10);
+ }
+ return ret;
+}
+
+static int gsc_i2c_write(uint chip, uint addr, u8 *buf, int len)
+{
+ int retry = 3;
+ int n = 0;
+ int ret;
+
+ while (n++ < retry) {
+ ret = i2c_write(chip, addr, 1, buf, len);
+ if (!ret)
+ break;
+ if (ret != -EREMOTEIO)
+ break;
+printf("%s 0x%02x retry %d\n", __func__, addr, n);
+ mdelay(10);
+ }
+ return ret;
+}
+
+/* disable boot watchdog - useful for an SPL that wants to use falcon mode */
+int gsc_boot_wd_disable(void)
+{
+ u8 buf[32];
+ int ret;
+
+ i2c_set_bus_num(GSC_BUSNO);
+ ret = gsc_i2c_read(GSC_SC_ADDR, 0, buf, sizeof(buf));
+ if (!ret) {
+ buf[GSC_SC_CTRL1] |= BIT(GSC_SC_CTRL1_WDDIS);
+ ret = gsc_i2c_write(GSC_SC_ADDR, GSC_SC_CTRL1, &buf[GSC_SC_CTRL1], 1);
+ printf("GSCv%d: v%d 0x%04x ",
+ memcmp(buf, buf + 16, 16) ? 3 : 2,
+ buf[GSC_SC_FWVER],
+ buf[GSC_SC_FWCRC] | buf[GSC_SC_FWCRC + 1] << 8);
+ if (buf[GSC_SC_STATUS] & BIT(GSC_SC_IRQ_WATCHDOG)) {
+ puts("RST:WDT ");
+ buf[GSC_SC_STATUS] &= ~BIT(GSC_SC_IRQ_WATCHDOG);
+ gsc_i2c_write(GSC_SC_ADDR, GSC_SC_STATUS, &buf[GSC_SC_STATUS], 1);
+ } else {
+ puts("RST:VIN ");
+ }
+ puts("WDT:disabled\n");
+ }
+
+ return ret;
+}
+
+#endif
diff --git a/include/gsc.h b/include/gsc.h
new file mode 100644
index 0000000..132c312
--- /dev/null
+++ b/include/gsc.h
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright 2022 Gateworks Corporation
+ */
+
+#ifndef _GSC_H_
+#define _GSC_H_
+
+/*
+ * board_gsc_info - Display additional board info
+ */
+void board_gsc_info(void);
+
+/*
+ * gsc_boot_wd_disable - disable the BOOT watchdog
+ *
+ * Return: 0 on success or negative error on failure
+ */
+int gsc_boot_wd_disable(void);
+
+#endif