drivers: spl: consistently use the $(SPL_TPL_) macro
To simplify drivers/Makefile a bit when using TPL/SPL, we consistently
use the $(SPL_TPL_) macro to test for drivers that have separate
configuration symbols for the full U-boot, SPL and TPL stages.
Instead of explicitly repeating them in two separate if-guarded
sections of the Makefile, we can now simply list these options once.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
diff --git a/drivers/Makefile b/drivers/Makefile
index e4a9cb4..a41444a 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -2,33 +2,34 @@
# SPDX-License-Identifier: GPL-2.0+
#
-obj-$(CONFIG_$(SPL_TPL_)DM) += core/
-obj-$(CONFIG_$(SPL_)CLK) += clk/
-obj-$(CONFIG_$(SPL_)LED) += led/
-obj-$(CONFIG_$(SPL_)PHY) += phy/
-obj-$(CONFIG_$(SPL_)PINCTRL) += pinctrl/
-obj-$(CONFIG_$(SPL_)RAM) += ram/
+obj-$(CONFIG_$(SPL_TPL_)CLK) += clk/
+obj-$(CONFIG_$(SPL_TPL_)DM) += core/
+obj-$(CONFIG_$(SPL_TPL_)DRIVERS_MISC_SUPPORT) += misc/ sysreset/ firmware/
+obj-$(CONFIG_$(SPL_TPL_)I2C_SUPPORT) += i2c/
+obj-$(CONFIG_$(SPL_TPL_)LED) += led/
+obj-$(CONFIG_$(SPL_TPL_)MMC_SUPPORT) += mmc/
+obj-$(CONFIG_$(SPL_TPL_)NAND_SUPPORT) += mtd/nand/
+obj-$(CONFIG_$(SPL_TPL_)PHY) += phy/
+obj-$(CONFIG_$(SPL_TPL_)PINCTRL) += pinctrl/
+obj-$(CONFIG_$(SPL_TPL_)RAM) += ram/
+obj-$(CONFIG_$(SPL_TPL_)SERIAL_SUPPORT) += serial/
+obj-$(CONFIG_$(SPL_TPL_)SPI_FLASH_SUPPORT) += mtd/spi/
+obj-$(CONFIG_$(SPL_TPL_)SPI_SUPPORT) += spi/
+ifndef CONFIG_TPL_BUILD
ifdef CONFIG_SPL_BUILD
obj-$(CONFIG_SPL_CPU_SUPPORT) += cpu/
obj-$(CONFIG_SPL_CRYPTO_SUPPORT) += crypto/
-obj-$(CONFIG_SPL_I2C_SUPPORT) += i2c/
obj-$(CONFIG_SPL_GPIO_SUPPORT) += gpio/
-obj-$(CONFIG_SPL_MMC_SUPPORT) += mmc/
obj-$(CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT) += ddr/fsl/
obj-$(CONFIG_ARMADA_38X) += ddr/marvell/a38x/
obj-$(CONFIG_ARMADA_XP) += ddr/marvell/axp/
obj-$(CONFIG_ALTERA_SDRAM) += ddr/altera/
-obj-$(CONFIG_SPL_SERIAL_SUPPORT) += serial/
-obj-$(CONFIG_SPL_SPI_SUPPORT) += spi/
obj-$(CONFIG_SPL_POWER_SUPPORT) += power/ power/pmic/
obj-$(CONFIG_SPL_POWER_SUPPORT) += power/regulator/
-obj-$(CONFIG_SPL_DRIVERS_MISC_SUPPORT) += misc/ sysreset/ firmware/
obj-$(CONFIG_SPL_MTD_SUPPORT) += mtd/
-obj-$(CONFIG_SPL_NAND_SUPPORT) += mtd/nand/
obj-$(CONFIG_SPL_ONENAND_SUPPORT) += mtd/onenand/
-obj-$(CONFIG_SPL_SPI_FLASH_SUPPORT) += mtd/spi/
obj-$(CONFIG_SPL_UBI) += mtd/ubispl/
obj-$(CONFIG_SPL_DMA_SUPPORT) += dma/
obj-$(CONFIG_SPL_ETH_SUPPORT) += net/
@@ -49,18 +50,13 @@
obj-$(CONFIG_SPL_USB_HOST_SUPPORT) += block/
obj-$(CONFIG_SPL_MMC_SUPPORT) += block/
obj-$(CONFIG_SPL_FPGA_SUPPORT) += fpga/
+
+endif
endif
ifdef CONFIG_TPL_BUILD
-obj-$(CONFIG_TPL_I2C_SUPPORT) += i2c/
-obj-$(CONFIG_TPL_DRIVERS_MISC_SUPPORT) += misc/ sysreset/ firmware/
-obj-$(CONFIG_TPL_MMC_SUPPORT) += mmc/
obj-$(CONFIG_TPL_MPC8XXX_INIT_DDR_SUPPORT) += ddr/fsl/
-obj-$(CONFIG_TPL_NAND_SUPPORT) += mtd/nand/
-obj-$(CONFIG_TPL_SERIAL_SUPPORT) += serial/
-obj-$(CONFIG_TPL_SPI_FLASH_SUPPORT) += mtd/spi/
-obj-$(CONFIG_TPL_SPI_SUPPORT) += spi/
endif