| /* |
| * Copyright 2015 Freescale Semiconductor, Inc. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __LS1043AQDS_H__ |
| #define __LS1043AQDS_H__ |
| |
| #include "ls1043a_common.h" |
| |
| #if defined(CONFIG_NAND_BOOT) || defined(CONFIG_SD_BOOT) |
| #define CONFIG_SYS_TEXT_BASE 0x82000000 |
| #elif defined(CONFIG_QSPI_BOOT) |
| #define CONFIG_SYS_TEXT_BASE 0x40100000 |
| #else |
| #define CONFIG_SYS_TEXT_BASE 0x60100000 |
| #endif |
| |
| #ifndef __ASSEMBLY__ |
| unsigned long get_board_sys_clk(void); |
| unsigned long get_board_ddr_clk(void); |
| #endif |
| |
| #define CONFIG_SYS_CLK_FREQ get_board_sys_clk() |
| #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() |
| |
| #define CONFIG_SKIP_LOWLEVEL_INIT |
| |
| #define CONFIG_LAYERSCAPE_NS_ACCESS |
| |
| #define CONFIG_DIMM_SLOTS_PER_CTLR 1 |
| /* Physical Memory Map */ |
| #define CONFIG_CHIP_SELECTS_PER_CTRL 4 |
| #define CONFIG_NR_DRAM_BANKS 2 |
| |
| #define CONFIG_DDR_SPD |
| #define SPD_EEPROM_ADDRESS 0x51 |
| #define CONFIG_SYS_SPD_BUS_NUM 0 |
| |
| #ifndef CONFIG_SPL |
| #define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */ |
| #endif |
| |
| #define CONFIG_DDR_ECC |
| #ifdef CONFIG_DDR_ECC |
| #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER |
| #define CONFIG_MEM_INIT_VALUE 0xdeadbeef |
| #endif |
| |
| #ifdef CONFIG_SYS_DPAA_FMAN |
| #define CONFIG_FMAN_ENET |
| #define CONFIG_PHY_VITESSE |
| #define CONFIG_PHY_REALTEK |
| #define CONFIG_PHYLIB_10G |
| #define RGMII_PHY1_ADDR 0x1 |
| #define RGMII_PHY2_ADDR 0x2 |
| #define SGMII_CARD_PORT1_PHY_ADDR 0x1C |
| #define SGMII_CARD_PORT2_PHY_ADDR 0x1D |
| #define SGMII_CARD_PORT3_PHY_ADDR 0x1E |
| #define SGMII_CARD_PORT4_PHY_ADDR 0x1F |
| /* PHY address on QSGMII riser card on slot 1 */ |
| #define QSGMII_CARD_PORT1_PHY_ADDR_S1 0x4 |
| #define QSGMII_CARD_PORT2_PHY_ADDR_S1 0x5 |
| #define QSGMII_CARD_PORT3_PHY_ADDR_S1 0x6 |
| #define QSGMII_CARD_PORT4_PHY_ADDR_S1 0x7 |
| /* PHY address on QSGMII riser card on slot 2 */ |
| #define QSGMII_CARD_PORT1_PHY_ADDR_S2 0x8 |
| #define QSGMII_CARD_PORT2_PHY_ADDR_S2 0x9 |
| #define QSGMII_CARD_PORT3_PHY_ADDR_S2 0xA |
| #define QSGMII_CARD_PORT4_PHY_ADDR_S2 0xB |
| #endif |
| |
| #ifdef CONFIG_RAMBOOT_PBL |
| #define CONFIG_SYS_FSL_PBL_PBI board/freescale/ls1043aqds/ls1043aqds_pbi.cfg |
| #endif |
| |
| #ifdef CONFIG_NAND_BOOT |
| #define CONFIG_SYS_FSL_PBL_RCW board/freescale/ls1043aqds/ls1043aqds_rcw_nand.cfg |
| #endif |
| |
| #ifdef CONFIG_SD_BOOT |
| #ifdef CONFIG_SD_BOOT_QSPI |
| #define CONFIG_SYS_FSL_PBL_RCW \ |
| board/freescale/ls1043aqds/ls1043aqds_rcw_sd_qspi.cfg |
| #else |
| #define CONFIG_SYS_FSL_PBL_RCW board/freescale/ls1043aqds/ls1043aqds_rcw_sd_ifc.cfg |
| #endif |
| #endif |
| |
| /* LPUART */ |
| #ifdef CONFIG_LPUART |
| #define CONFIG_LPUART_32B_REG |
| #endif |
| |
| /* SATA */ |
| #define CONFIG_LIBATA |
| #define CONFIG_SCSI_AHCI |
| #define CONFIG_SCSI_AHCI_PLAT |
| |
| /* EEPROM */ |
| #define CONFIG_ID_EEPROM |
| #define CONFIG_SYS_I2C_EEPROM_NXID |
| #define CONFIG_SYS_EEPROM_BUS_NUM 0 |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 |
| |
| #define CONFIG_SYS_SATA AHCI_BASE_ADDR |
| |
| #define CONFIG_SYS_SCSI_MAX_SCSI_ID 1 |
| #define CONFIG_SYS_SCSI_MAX_LUN 1 |
| #define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ |
| CONFIG_SYS_SCSI_MAX_LUN) |
| |
| /* |
| * IFC Definitions |
| */ |
| #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) |
| #define CONFIG_SYS_NOR0_CSPR_EXT (0x0) |
| #define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ |
| CSPR_PORT_SIZE_16 | \ |
| CSPR_MSEL_NOR | \ |
| CSPR_V) |
| #define CONFIG_SYS_NOR1_CSPR_EXT (0x0) |
| #define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \ |
| + 0x8000000) | \ |
| CSPR_PORT_SIZE_16 | \ |
| CSPR_MSEL_NOR | \ |
| CSPR_V) |
| #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128 * 1024 * 1024) |
| |
| #define CONFIG_SYS_NOR_CSOR (CSOR_NOR_ADM_SHIFT(4) | \ |
| CSOR_NOR_TRHZ_80) |
| #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ |
| FTIM0_NOR_TEADC(0x5) | \ |
| FTIM0_NOR_TEAHC(0x5)) |
| #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ |
| FTIM1_NOR_TRAD_NOR(0x1a) | \ |
| FTIM1_NOR_TSEQRAD_NOR(0x13)) |
| #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ |
| FTIM2_NOR_TCH(0x4) | \ |
| FTIM2_NOR_TWPH(0xe) | \ |
| FTIM2_NOR_TWP(0x1c)) |
| #define CONFIG_SYS_NOR_FTIM3 0 |
| |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ |
| |
| #define CONFIG_SYS_FLASH_EMPTY_INFO |
| #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS, \ |
| CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000} |
| |
| #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS |
| #define CONFIG_SYS_WRITE_SWAPPED_DATA |
| |
| /* |
| * NAND Flash Definitions |
| */ |
| #define CONFIG_NAND_FSL_IFC |
| |
| #define CONFIG_SYS_NAND_BASE 0x7e800000 |
| #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE |
| |
| #define CONFIG_SYS_NAND_CSPR_EXT (0x0) |
| |
| #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ |
| | CSPR_PORT_SIZE_8 \ |
| | CSPR_MSEL_NAND \ |
| | CSPR_V) |
| #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) |
| #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ |
| | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ |
| | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ |
| | CSOR_NAND_RAL_3 /* RAL = 3 Bytes */ \ |
| | CSOR_NAND_PGS_2K /* Page Size = 2K */ \ |
| | CSOR_NAND_SPRZ_64 /* Spare size = 64 */ \ |
| | CSOR_NAND_PB(64)) /* 64 Pages Per Block */ |
| |
| #define CONFIG_SYS_NAND_ONFI_DETECTION |
| |
| #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x7) | \ |
| FTIM0_NAND_TWP(0x18) | \ |
| FTIM0_NAND_TWCHT(0x7) | \ |
| FTIM0_NAND_TWH(0xa)) |
| #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ |
| FTIM1_NAND_TWBE(0x39) | \ |
| FTIM1_NAND_TRR(0xe) | \ |
| FTIM1_NAND_TRP(0x18)) |
| #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0xf) | \ |
| FTIM2_NAND_TREH(0xa) | \ |
| FTIM2_NAND_TWHRE(0x1e)) |
| #define CONFIG_SYS_NAND_FTIM3 0x0 |
| |
| #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| #define CONFIG_MTD_NAND_VERIFY_WRITE |
| |
| #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) |
| #endif |
| |
| #ifdef CONFIG_NAND_BOOT |
| #define CONFIG_SPL_PAD_TO 0x20000 /* block aligned */ |
| #define CONFIG_SYS_NAND_U_BOOT_OFFS CONFIG_SPL_PAD_TO |
| #define CONFIG_SYS_NAND_U_BOOT_SIZE (640 << 10) |
| #endif |
| |
| #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) |
| #define CONFIG_QIXIS_I2C_ACCESS |
| #define CONFIG_SYS_I2C_EARLY_INIT |
| #endif |
| |
| /* |
| * QIXIS Definitions |
| */ |
| #define CONFIG_FSL_QIXIS |
| |
| #ifdef CONFIG_FSL_QIXIS |
| #define QIXIS_BASE 0x7fb00000 |
| #define QIXIS_BASE_PHYS QIXIS_BASE |
| #define CONFIG_SYS_I2C_FPGA_ADDR 0x66 |
| #define QIXIS_LBMAP_SWITCH 6 |
| #define QIXIS_LBMAP_MASK 0x0f |
| #define QIXIS_LBMAP_SHIFT 0 |
| #define QIXIS_LBMAP_DFLTBANK 0x00 |
| #define QIXIS_LBMAP_ALTBANK 0x04 |
| #define QIXIS_LBMAP_NAND 0x09 |
| #define QIXIS_LBMAP_SD 0x00 |
| #define QIXIS_LBMAP_SD_QSPI 0xff |
| #define QIXIS_LBMAP_QSPI 0xff |
| #define QIXIS_RCW_SRC_NAND 0x106 |
| #define QIXIS_RCW_SRC_SD 0x040 |
| #define QIXIS_RCW_SRC_QSPI 0x045 |
| #define QIXIS_RST_CTL_RESET 0x41 |
| #define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 |
| #define QIXIS_RCFG_CTL_RECONFIG_START 0x21 |
| #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 |
| |
| #define CONFIG_SYS_FPGA_CSPR_EXT (0x0) |
| #define CONFIG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) | \ |
| CSPR_PORT_SIZE_8 | \ |
| CSPR_MSEL_GPCM | \ |
| CSPR_V) |
| #define CONFIG_SYS_FPGA_AMASK IFC_AMASK(64 * 1024) |
| #define CONFIG_SYS_FPGA_CSOR (CSOR_NOR_ADM_SHIFT(4) | \ |
| CSOR_NOR_NOR_MODE_AVD_NOR | \ |
| CSOR_NOR_TRHZ_80) |
| |
| /* |
| * QIXIS Timing parameters for IFC GPCM |
| */ |
| #define CONFIG_SYS_FPGA_FTIM0 (FTIM0_GPCM_TACSE(0xc) | \ |
| FTIM0_GPCM_TEADC(0x20) | \ |
| FTIM0_GPCM_TEAHC(0x10)) |
| #define CONFIG_SYS_FPGA_FTIM1 (FTIM1_GPCM_TACO(0x50) | \ |
| FTIM1_GPCM_TRAD(0x1f)) |
| #define CONFIG_SYS_FPGA_FTIM2 (FTIM2_GPCM_TCS(0x8) | \ |
| FTIM2_GPCM_TCH(0x8) | \ |
| FTIM2_GPCM_TWP(0xf0)) |
| #define CONFIG_SYS_FPGA_FTIM3 0x0 |
| #endif |
| |
| #ifdef CONFIG_NAND_BOOT |
| #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT |
| #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR |
| #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK |
| #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR |
| #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 |
| #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 |
| #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 |
| #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 |
| #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT |
| #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR |
| #define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK |
| #define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR |
| #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 |
| #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 |
| #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 |
| #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 |
| #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR1_CSPR_EXT |
| #define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR1_CSPR |
| #define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK |
| #define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR |
| #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0 |
| #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1 |
| #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2 |
| #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3 |
| #define CONFIG_SYS_CSPR3_EXT CONFIG_SYS_FPGA_CSPR_EXT |
| #define CONFIG_SYS_CSPR3 CONFIG_SYS_FPGA_CSPR |
| #define CONFIG_SYS_AMASK3 CONFIG_SYS_FPGA_AMASK |
| #define CONFIG_SYS_CSOR3 CONFIG_SYS_FPGA_CSOR |
| #define CONFIG_SYS_CS3_FTIM0 CONFIG_SYS_FPGA_FTIM0 |
| #define CONFIG_SYS_CS3_FTIM1 CONFIG_SYS_FPGA_FTIM1 |
| #define CONFIG_SYS_CS3_FTIM2 CONFIG_SYS_FPGA_FTIM2 |
| #define CONFIG_SYS_CS3_FTIM3 CONFIG_SYS_FPGA_FTIM3 |
| #else |
| #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT |
| #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR |
| #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK |
| #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR |
| #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 |
| #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 |
| #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 |
| #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 |
| #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT |
| #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR |
| #define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK |
| #define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR |
| #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 |
| #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 |
| #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 |
| #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 |
| #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT |
| #define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR |
| #define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK |
| #define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR |
| #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0 |
| #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1 |
| #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2 |
| #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3 |
| #define CONFIG_SYS_CSPR3_EXT CONFIG_SYS_FPGA_CSPR_EXT |
| #define CONFIG_SYS_CSPR3 CONFIG_SYS_FPGA_CSPR |
| #define CONFIG_SYS_AMASK3 CONFIG_SYS_FPGA_AMASK |
| #define CONFIG_SYS_CSOR3 CONFIG_SYS_FPGA_CSOR |
| #define CONFIG_SYS_CS3_FTIM0 CONFIG_SYS_FPGA_FTIM0 |
| #define CONFIG_SYS_CS3_FTIM1 CONFIG_SYS_FPGA_FTIM1 |
| #define CONFIG_SYS_CS3_FTIM2 CONFIG_SYS_FPGA_FTIM2 |
| #define CONFIG_SYS_CS3_FTIM3 CONFIG_SYS_FPGA_FTIM3 |
| #endif |
| |
| /* |
| * I2C bus multiplexer |
| */ |
| #define I2C_MUX_PCA_ADDR_PRI 0x77 |
| #define I2C_MUX_PCA_ADDR_SEC 0x76 /* Secondary multiplexer */ |
| #define I2C_RETIMER_ADDR 0x18 |
| #define I2C_MUX_CH_DEFAULT 0x8 |
| #define I2C_MUX_CH_CH7301 0xC |
| #define I2C_MUX_CH5 0xD |
| #define I2C_MUX_CH7 0xF |
| |
| #define I2C_MUX_CH_VOL_MONITOR 0xa |
| |
| /* Voltage monitor on channel 2*/ |
| #define I2C_VOL_MONITOR_ADDR 0x40 |
| #define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2 |
| #define I2C_VOL_MONITOR_BUS_V_OVF 0x1 |
| #define I2C_VOL_MONITOR_BUS_V_SHIFT 3 |
| |
| #define CONFIG_VID_FLS_ENV "ls1043aqds_vdd_mv" |
| #ifndef CONFIG_SPL_BUILD |
| #define CONFIG_VID |
| #endif |
| #define CONFIG_VOL_MONITOR_IR36021_SET |
| #define CONFIG_VOL_MONITOR_INA220 |
| /* The lowest and highest voltage allowed for LS1043AQDS */ |
| #define VDD_MV_MIN 819 |
| #define VDD_MV_MAX 1212 |
| |
| /* QSPI device */ |
| #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) |
| #define CONFIG_FSL_QSPI |
| #ifdef CONFIG_FSL_QSPI |
| #define CONFIG_SPI_FLASH_SPANSION |
| #define FSL_QSPI_FLASH_SIZE (1 << 24) |
| #define FSL_QSPI_FLASH_NUM 2 |
| #endif |
| #endif |
| |
| /* USB */ |
| #define CONFIG_HAS_FSL_XHCI_USB |
| #ifdef CONFIG_HAS_FSL_XHCI_USB |
| #define CONFIG_USB_XHCI_FSL |
| #define CONFIG_USB_MAX_CONTROLLER_COUNT 3 |
| #endif |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_MISC_INIT_R |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_AUTO_COMPLETE |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE |
| |
| #define CONFIG_SYS_MEMTEST_START 0x80000000 |
| #define CONFIG_SYS_MEMTEST_END 0x9fffffff |
| |
| #define CONFIG_SYS_HZ 1000 |
| |
| #define CONFIG_SYS_INIT_SP_OFFSET \ |
| (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| |
| #ifdef CONFIG_SPL_BUILD |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE |
| #else |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ |
| #endif |
| |
| /* |
| * Environment |
| */ |
| #define CONFIG_ENV_OVERWRITE |
| |
| #ifdef CONFIG_NAND_BOOT |
| #define CONFIG_ENV_SIZE 0x2000 |
| #define CONFIG_ENV_OFFSET (24 * CONFIG_SYS_NAND_BLOCK_SIZE) |
| #elif defined(CONFIG_SD_BOOT) |
| #define CONFIG_ENV_OFFSET (3 * 1024 * 1024) |
| #define CONFIG_SYS_MMC_ENV_DEV 0 |
| #define CONFIG_ENV_SIZE 0x2000 |
| #elif defined(CONFIG_QSPI_BOOT) |
| #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ |
| #define CONFIG_ENV_OFFSET 0x300000 /* 3MB */ |
| #define CONFIG_ENV_SECT_SIZE 0x10000 |
| #else |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x300000) |
| #define CONFIG_ENV_SECT_SIZE 0x20000 |
| #define CONFIG_ENV_SIZE 0x20000 |
| #endif |
| |
| #define CONFIG_CMDLINE_TAG |
| |
| #include <asm/fsl_secure_boot.h> |
| |
| #endif /* __LS1043AQDS_H__ */ |